summaryrefslogtreecommitdiff
path: root/doc/rfc/rfc4319.txt
diff options
context:
space:
mode:
Diffstat (limited to 'doc/rfc/rfc4319.txt')
-rw-r--r--doc/rfc/rfc4319.txt4203
1 files changed, 4203 insertions, 0 deletions
diff --git a/doc/rfc/rfc4319.txt b/doc/rfc/rfc4319.txt
new file mode 100644
index 0000000..580e2db
--- /dev/null
+++ b/doc/rfc/rfc4319.txt
@@ -0,0 +1,4203 @@
+
+
+
+
+
+
+Network Working Group C. Sikes
+Request for Comments: 4319 Zhone Technologies, Inc.
+Obsoletes: 3276 B. Ray
+Category: Standards Track PESA Switching Systems, Inc.
+ R. Abbi
+ Alcatel USA
+ December 2005
+
+
+ Definitions of Managed Objects for
+ High Bit-Rate DSL - 2nd generation (HDSL2) and
+ Single-Pair High-Speed Digital Subscriber Line (SHDSL) Lines
+
+Status of This Memo
+
+ This document specifies an Internet standards track protocol for the
+ Internet community, and requests discussion and suggestions for
+ improvements. Please refer to the current edition of the "Internet
+ Official Protocol Standards" (STD 1) for the standardization state
+ and status of this protocol. Distribution of this memo is unlimited.
+
+Copyright Notice
+
+ Copyright (C) The Internet Society (2005).
+
+Abstract
+
+ This document defines a Management Information Base (MIB) module for
+ use with network management protocols in the Internet community. In
+ particular, it describes objects used for managing High Bit-Rate
+ Digital Subscriber Line (DSL) - 2nd generation (HDSL2) and
+ Single-Pair High-Speed Digital Subscriber Line (SHDSL) interfaces.
+ This document introduces extensions to several objects and textual
+ conventions defined in HDSL2-SHDSL-Line MIB (RFC 3276). This
+ document obsoletes RFC 3276.
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+Sikes, et al. Standards Track [Page 1]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+Table of Contents
+
+ 1. The Internet-Standard Management Framework ......................2
+ 2. Overview ........................................................2
+ 2.1. Relationship to Other MIBs .................................3
+ 2.1.1. General IF-MIB Integration (RFC 2863) ...............3
+ 2.1.2. Usage of ifTable ....................................3
+ 2.2. IANA Considerations ........................................4
+ 2.3. Conventions Used in the MIB Module .........................5
+ 2.3.1. Naming Conventions ..................................5
+ 2.3.2. Textual Conventions .................................5
+ 2.4. Structure ..................................................7
+ 2.5. Line Topology ..............................................9
+ 2.6. Counters, Interval Buckets, and Thresholds ................10
+ 2.7. Profiles ..................................................11
+ 2.8. Notifications .............................................12
+ 3. Definitions ....................................................14
+ 4. Implementation Analysis ........................................66
+ 5. Security Considerations ........................................66
+ 6. Acknowledgements ...............................................71
+ 7. References .....................................................72
+ 7.1. Normative References ......................................72
+ 7.2. Informative References ....................................73
+
+1. The Internet-Standard Management Framework
+
+ For a detailed overview of the documents that describe the current
+ Internet-Standard Management Framework, please refer to Section 7 of
+ RFC 3410 [RFC3410].
+
+ Managed objects are accessed via a virtual information store, termed
+ the Management Information Base or MIB. MIB objects are generally
+ accessed through the Simple Network Management Protocol (SNMP).
+ Objects in the MIB are defined using the mechanisms defined in the
+ Structure of Management Information (SMI). This memo specifies a MIB
+ module that is compliant to the SMIv2, which is described in STD 58,
+ RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
+ [RFC2580].
+
+ The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
+ "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
+ document are to be interpreted as described in RFC 2119 [RFC2119].
+
+2. Overview
+
+ This document defines a Management Information Base (MIB) module for
+ use with network management protocols in the Internet community for
+ the purpose of managing HDSL2/SHDSL lines.
+
+
+
+Sikes, et al. Standards Track [Page 2]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ The MIB module described in RFC 3276 [RFC3276] describes objects used
+ for managing High Bit-Rate DSL - 2nd generation (HDSL2) [T1E1.4] and
+ Single-Pair High-Speed Digital Subscriber Line (SHDSL) interfaces
+ [G.991.2]. These object descriptions are based upon the
+ specifications for the HDSL2 and SHDSL Embedded Operations Channel
+ (EOC), as defined in the American National Standards Institute (ANSI)
+ T1E1.4/2000-006 [T1E1.4] and International Telecommunication Union
+ (ITU) G.991.2 [G.991.2].
+
+ This document obsoletes RFC 3276 [RFC3276], which supports G.shdsl in
+ that the MIB module described herein supports G.shdsl.bis as
+ described in the G.991.2 [G.991.2]. In addition, objects have been
+ added to improve the management of SHDSL lines.
+
+ The MIB module is located in the MIB tree under MIB 2 transmission,
+ as discussed in the MIB-2 Integration (RFC 2863 [RFC2863]) section of
+ this document.
+
+2.1. Relationship to Other MIBs
+
+ This section outlines the relationship of this MIB module with other
+ MIB modules described in RFCs. Specifically, the IF-MIB, as
+ presented in RFC 2863 [RFC2863], is discussed.
+
+2.1.1. General IF-MIB Integration (RFC 2863)
+
+ The HDSL2/SHDSL line MIB specifies the detailed attributes of a data
+ interface. As such, it needs to integrate with RFC 2863 [RFC2863].
+ The IANA has assigned the following ifTypes to HDSL2 and SHDSL:
+
+ IANAifType ::= TEXTUAL-CONVENTION
+ ...
+ SYNTAX INTEGER {
+ ...
+ hdsl2 (168), -- High Bit-Rate DSL, 2nd generation
+ shdsl (169), -- Multirate HDSL2
+ ...
+ }
+
+ Note that the ifFixedLengthGroup from RFC 2863 [RFC2863] MUST be
+ supported and that the ifRcvAddressGroup does not apply to this MIB
+ module.
+
+2.1.2. Usage of ifTable
+
+ The MIB branch identified by this ifType contains tables appropriate
+ for this interface type. Most such tables extend the ifEntry table
+ and are indexed by ifIndex. For interfaces in systems implementing
+
+
+
+Sikes, et al. Standards Track [Page 3]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ this MIB module, those table entries indexed by ifIndex MUST be
+ persistent.
+
+ The following attributes are part of the mandatory
+ ifGeneralInformationGroup in RFC 2863 [RFC2863] and are not
+ duplicated in the HDSL2/SHDSL line MIB.
+
+ ===================================================================
+
+ ifIndex Interface index.
+
+ ifDescr See interfaces MIB [RFC2863].
+
+ ifType hdsl2(168) or shdsl(169).
+
+ ifSpeed Set as appropriate.
+ (This is fixed at 1552000 for HDSL2
+ lines)
+
+ ifPhysAddress This object MUST have an octet string
+ with zero length.
+
+ ifAdminStatus See interfaces MIB [RFC2863].
+
+ ifOperStatus See interfaces MIB [RFC2863].
+
+ ifLastChange See interfaces MIB [RFC2863].
+
+ ifName See interfaces MIB [RFC2863].
+
+ ifAlias See interfaces MIB [RFC2863].
+
+ ifLinkUpDownTrapEnable Default to enabled(1).
+
+ ifHighSpeed Set as appropriate.
+ (For HDSL2 lines, this is fixed at 2)
+
+ ifConnectorPresent Set as appropriate.
+
+ ===================================================================
+ Figure 1: Use of ifTable Objects
+
+2.2. IANA Considerations
+
+ The HDSL2-SHDSL-LINE-MIB module requires the allocation of a single
+ object identifier for its MODULE-IDENTITY. The IANA has allocated
+ this object identifier in the transmission subtree (48), defined in
+ the SNMPv2-SMI MIB module.
+
+
+
+Sikes, et al. Standards Track [Page 4]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ The assignment was in fact done when RFC 3276 was published, and this
+ revision of the RFC does not require any new action from IANA.
+
+2.3. Conventions Used in the MIB Module
+
+2.3.1. Naming Conventions
+
+ A. xtuC refers to a central site terminal unit;
+ H2TU-C for HDSL2, or STU-C for SHDSL.
+ B. xtuR refers to a remote site terminal unit;
+ H2TU-R for HDSL2, or STU-R for SHDSL.
+ C. xtu refers to a terminal unit; either an xtuC or xtuR.
+ D. xru refer to a regenerator unit;
+ H2RU for HDSL2, or SRU for SHDSL.
+ E. xU refers to any HDSL2/SHDSL unit; either an xtu or xru.
+ F. CRC is Cyclic Redundancy Check [G.991.2].
+ G. ES means Errored Second [G.991.2].
+ J. LOSW means Loss of Sync Word [G.991.2].
+ I. LOSWS means LOSW Seconds [G.991.2].
+ J. SES means Severely Errored Second [G.991.2].
+ K. SNR means Signal-to-Noise Ratio [G.991.2].
+ L. UAS means Unavailable Second [G.991.2].
+
+2.3.2. Textual Conventions
+
+ The following textual conventions are defined to reflect the line
+ topology in the MIB module (further discussed in the following
+ section) and to define the behavior of the statistics to be
+ maintained by an agent.
+
+ o Hdsl2ShdslUnitId:
+
+ Attributes with this syntax uniquely identify each unit in an
+ HDSL2/SHDSL span. It mirrors the EOC addressing mechanism:
+
+ xtuC(1) - central office (CO) terminal unit
+ xtuR(2) - customer premises equipment (CPE)
+ terminal unit
+ xru1(3) .. xru8(10) - regenerators, numbered from
+ central office side
+
+ o Hdsl2ShdslUnitSide:
+
+ Attributes with this syntax reference the two sides of a unit:
+
+ networkSide(1) - N in figure 2, below
+ customerSide(2) - C in figure 2, below
+
+
+
+
+Sikes, et al. Standards Track [Page 5]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ o Hdsl2ShdslWirePair:
+
+ Attributes with this syntax reference the wire pairs connecting
+ the units:
+
+ wirePair1(1) - First pair for HDSL2/SHDSL.
+ wirePair2(2) - Optional second pair for SHDSL only.
+ wirePair3(3) - Optional third pair for SHDSL.bis only.
+ wirePair4(4) - Optional fourth pair for SHDSL.bis only.
+
+ o Hdsl2ShdslTransmissionModeType:
+
+ Attributes with this syntax specify the regional setting for an
+ SHDSL line. Specified as a BITS construct, the two mode types
+ are:
+
+ region1 - ITU-T G.991.2 Annex A
+ region2 - ITU-T G.991.2 Annex B
+
+ o Hdsl2ShdslPerfCurrDayCount:
+
+ Attributes with this syntax define the behavior of the 1-day (24
+ hour) gauges found in the MIB module.
+
+ o Hdsl2Shdsl1DayIntervalCount:
+
+ Attributes with this syntax define the behavior of the 1-day (24
+ hour) interval counters found in the MIB module.
+
+ o Hdsl2ShdslPerfTimeElapsed:
+
+ Attributes with this syntax define the behavior of the elapsed
+ time counters found in the MIB module.
+
+ o Hdsl2ShdslPerfIntervalThreshold:
+
+ Attributes with this syntax define the behavior of the alarm
+ thresholds found in the MIB module.
+
+ o Hdsl2ShdslClockReferenceType:
+
+ Attributes with this syntax define the clock references for the
+ HDSL2/SHDSL span.
+
+
+
+
+
+
+
+
+Sikes, et al. Standards Track [Page 6]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+2.4. Structure
+
+ The MIB module is structured into the following MIB groups:
+
+ o Span Configuration Group:
+
+ This group supports MIB objects for configuring parameters for the
+ HDSL2/SHDSL span. It contains the following table:
+
+ - hdsl2ShdslSpanConfTable
+
+ o Span Status Group:
+
+ This group supports MIB objects for retrieving span status
+ information. It contains the following table:
+
+ - hdsl2ShdslSpanStatusTable
+
+ o Unit Inventory Group:
+
+ This group supports MIB objects for retrieving unit inventory
+ information about units in HDSL2/SHDSL lines via the EOC. It
+ contains the following table:
+
+ - hdsl2ShdslInventoryTable
+
+ o Segment Endpoint Configuration Group:
+
+ This group supports MIB objects for configuring parameters for the
+ HDSL2/SHDSL segment endpoints. It contains the following table:
+
+ - hdsl2ShdslEndpointConfTable
+
+ o Segment Endpoint Current Status/Performance Group:
+
+ This group supports MIB objects that provide the current status/
+ performance information relating to segment endpoints. It
+ contains the following table:
+
+ - hdsl2ShdslEndpointCurrTable
+
+ o Segment Endpoint 15-Minute Interval Status/Performance Group:
+
+ This group supports MIB objects that provide historic status/
+ performance information relating to segment endpoints in 15-minute
+ intervals. It contains the following table:
+
+ - hdsl2Shdsl15MinIntervalTable
+
+
+
+Sikes, et al. Standards Track [Page 7]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ o Segment Endpoint 1-Day Interval Status/Performance Group:
+
+ This group supports MIB objects that provide historic status/
+ performance information relating to segment endpoints in 1-day
+ intervals. It contains the following table:
+
+ - hdsl2Shdsl1DayIntervalTable
+
+ o Maintenance Group:
+
+ This group supports MIB objects for performing maintenance
+ operations such as loopbacks for HDSL2/SHDSL lines. It contains
+ the following table(s):
+
+ - hdsl2ShdslEndpointMaintTable
+ - hdsl2ShdslUnitMaintTable
+
+ o Span Configuration Profile Group:
+
+ This group supports MIB objects for defining configuration
+ profiles for HDSL2/SHDSL spans. It contains the following table:
+
+ - hdsl2ShdslSpanConfProfileTable
+
+ o Segment Endpoint Alarm Configuration Profile Group:
+
+ This group supports MIB objects for defining alarm configuration
+ profiles for HDSL2/SHDSL segment endpoints. It contains the
+ following table:
+
+ - hdsl2ShdslEndpointAlarmConfProfileTable
+
+ o Notifications Group:
+
+ This group defines the notifications supported for HDSL2/SHDSL
+ lines:
+
+ - hdsl2ShdslLoopAttenCrossing
+ - hdsl2ShdslSNRMarginCrossing
+ - hdsl2ShdslPerfESThresh
+ - hdsl2ShdslPerfSESThresh
+ - hdsl2ShdslPerfCRCanomaliesThresh
+ - hdsl2ShdslPerfLOSWSThresh
+ - hdsl2ShdslPerfUASThresh
+ - hdsl2ShdslSpanInvalidNumRepeaters
+ - hdsl2ShdslLoopbackFailure
+ - hdsl2ShdslpowerBackoff
+ - hdsl2ShdsldeviceFault
+
+
+
+Sikes, et al. Standards Track [Page 8]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ - hdsl2ShdsldcContinuityFault
+ - hdsl2ShdslconfigInitFailure
+ - hdsl2ShdslprotocolInitFailure
+ - hdsl2ShdslnoNeighborPresent
+ - hdsl2ShdslLocalPowerLoss
+
+ o SHDSL Wire Pair Group:
+
+ This group supports MIB objects that provide status of the SHDSL-
+ specific wire pairs.
+
+ - hdsl2ShdslEndpointCurrTipRingReversal
+ - hdsl2ShdslEndpointCurrActivationState
+
+ o Payload Group:
+
+ This group supports MIB objects for retrieving payload rates that
+ exclude any framing overhead.
+
+ - hdsl2ShdslStatusMaxAttainablePayloadRate
+ - hdsl2ShdslStatusActualPayloadRate
+
+2.5. Line Topology
+
+ An HDSL2/SHDSL line consists of a minimum of two units: xtuC (the
+ central termination unit) and an xtuR (the remote termination unit).
+ The line may optionally support up to 8 repeater/regenerator units
+ (xru) as shown in the figure below.
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+Sikes, et al. Standards Track [Page 9]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ <-- Network Side Customer Side -->
+
+ |</////////////////// HDSL2/SHDSL Span ////////////////////>|
+
+ <~~~> <~~~> HDSL2/SHDSL Segments <~~~>
+
+ +-------+ +-------+ +-------+ +-------+ +-------+
+ + C=1=N C=1=N C=..1..=N C=1=N +
+ | xtuC | | xru1 | | xru2 | | xru8 | | xtuR |
+ + C=2=N C=2=N C=..2..=N C=2=N +
+ +-------+ +-------+ +-------+ +-------+ +-------+
+
+ Key: <////> HDSL2/SHDSL span
+ <~~~~> HDSL2/SHDSL segment
+ =1= HDSL2/SHDSL wire-pair-1
+ =2= SHDSL optional wire-pair-2 (Not applicable to HDSL2)
+ C Customer side segment endpoint (modem)
+ N Network side segment endpoint (modem)
+
+ Figure 2: General Topology for an HDSL2/SHDSL Line
+
+2.6. Counters, Interval Buckets, and Thresholds
+
+ For SNR Margin, Loop Attenuation, ES, SES, CRC anomalies, LOSW, and
+ UAS, there are event counters, current 15-minute and 0 to 96 15-
+ minute history bucket(s) of "interval-counters", as well as current
+ and 0 to 30 previous 1-day interval-counter(s). Each current 15-
+ minute event bucket has an associated threshold notification.
+
+ Unlike RFC 3593 [RFC3593] and RFC 2662 [RFC2662], there is no
+ representation in the MIB module for invalid buckets. In those cases
+ where the data for an interval is suspect or known to be invalid, the
+ agent MUST NOT report the interval. If the current 15-minute event
+ bucket is determined to be invalid, notifications based upon the
+ value of the event bucket MUST NOT be generated.
+
+ Not reporting an interval will result in holes in the associated
+ table. For example, the table hdsl2Shdsl15MinIntervalTable is
+ indexed by { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
+ hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}. If
+ interval 12 is determined to be invalid but intervals 11 and 13 are
+ valid, a Get Next operation on the indices .1.1.1.1.11 would return
+ indices .1.1.1.1.13.
+
+ There is no requirement for an agent to ensure a fixed relationship
+ between the start of a 15-minute interval and any wall clock;
+ however, some implementations may align the 15-minute intervals with
+
+
+
+
+Sikes, et al. Standards Track [Page 10]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ quarter hours. Likewise, an implementation may choose to align 1-day
+ intervals with the start of a day.
+
+ Counters are not reset when an xU is reinitialized, only when the
+ agent is reset or reinitialized (or under specific request outside
+ the scope of this MIB module).
+
+2.7. Profiles
+
+ As a managed node can handle a large number of xUs (e.g., hundreds or
+ perhaps thousands of lines), provisioning every parameter on every xU
+ may become burdensome. Moreover, most lines are provisioned
+ identically with the same set of parameters. To simplify the
+ provisioning process, this MIB module makes use of profiles. A
+ profile is a set of parameters that can be shared by multiple lines
+ using the same configuration.
+
+ The following profiles are used in this MIB module:
+
+ o Span Configuration Profiles - Span configuration profiles contain
+ parameters for configuring HDSL2/SHDSL spans. They are defined in
+ the hdsl2ShdslSpanConfProfileTable. Since span configuration
+ parameters are only applicable for SHDSL, the support for span
+ configuration profiles is optional for HDSL2 interfaces.
+
+ Note that the configuration of the span dictates the behavior for
+ each individual segment endpoint in the span. If a different
+ configuration is provisioned for any given segment endpoint within
+ the span, the new configuration for this segment endpoint will
+ override the span configuration for this segment endpoint only.
+
+ o Segment Endpoint Alarm Configuration Profiles - These profiles
+ contain parameters for configuring alarm thresholds for HDSL2/
+ SHDSL segment endpoints. These profiles are defined in the
+ hdsl2ShdslEndpointAlarmConfProfileTable.
+
+ The index value for this profile is a locally-unique
+ administratively-assigned name for the profile having the textual
+ convention 'SnmpAdminString' (RFC 3411 [RFC3411]).
+
+ One or more lines may be configured to share parameters of a single
+ profile (e.g., hdsl2ShdslEndpointAlarmConfProfile = 'silver') by
+ setting its hdsl2ShdslEndpointAlarmConfProfile objects to the value
+ of this profile. If a change is made to the profile, all lines that
+ refer to it will be reconfigured to the changed parameters. Before a
+ profile can be deleted or taken out of service, it must be first
+ unreferenced from all associated lines.
+
+
+
+
+Sikes, et al. Standards Track [Page 11]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ Implementations MUST provide a default profile whose name is 'DEFVAL'
+ for each profile type. The values of the associated parameters will
+ be vendor specific unless otherwise indicated in this document.
+ Before a line's profiles have been set, these profiles will be
+ automatically used by setting hdsl2ShdslEndpointAlarmConfProfile and
+ hdsl2ShdslSpanConfProfile to 'DEFVAL' where appropriate. This
+ default profile name, 'DEFVAL', is considered reserved in the context
+ of profiles defined in this MIB module.
+
+ Profiles are created, assigned, and deleted dynamically using the
+ profile name and profile row status in each of the four profile
+ tables.
+
+ Profile changes MUST take effect immediately. These changes MAY
+ result in a restart (hard reset or soft restart) of the units on the
+ line.
+
+2.8. Notifications
+
+ The ability to generate the SNMP notifications coldStart/warmStart
+ (per [RFC3418]), which are per agent (e.g., per Digital Subscriber
+ Line Access Multiplexer, or DSLAM, in such a device), and linkUp/
+ linkDown (per [RFC2863]), which are per interface (i.e., HDSL2/SHDSL
+ line) is required.
+
+ A linkDown notification MAY be generated whenever any ES, SES, CRC
+ anomaly, LOSW, or UAS event occurs. The corresponding linkUp
+ notification MAY be sent when all link failure conditions are
+ cleared.
+
+ The notifications defined in this MIB module are for initialization
+ failure and for the threshold crossings associated with the following
+ events: ES, SES, CRC anomaly, LOSW, and UAS. Each threshold has its
+ own enable/threshold value. When that value is 0, the notification
+ is disabled.
+
+ The hdsl2ShdslEndpointCurrStatus is a bitmask representing all
+ outstanding error conditions associated with a particular segment
+ endpoint. Note that since the status of remote endpoints is obtained
+ via the EOC, this information may be unavailable for units that are
+ unreachable via EOC during a line error condition. Therefore, not
+ all conditions may always be included in its current status.
+ Notifications corresponding to the bit fields in this object are
+ defined.
+
+ Two alarm conditions, SNR Margin Alarm and Loop Attenuation Alarm,
+ are organized in a manner slightly different from that implied in the
+ EOC specifications. In the MIB module, these alarm conditions are
+
+
+
+Sikes, et al. Standards Track [Page 12]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ tied to the two thresholds, hdsl2ShdslEndpointThreshSNRMargin and
+ hdsl2ShdslEndpointThreshLoopAttenuation, found in the
+ hdsl2ShdslEndpointAlarmConfProfileTable. In the EOC, the alarm
+ conditions associated with these thresholds are per unit. In the MIB
+ module, these alarm conditions are per endpoint. For terminal units,
+ this has no impact. For repeaters, this implies an implementation
+ variance where the agent in the terminal unit is responsible for
+ detecting a threshold crossing. As the reporting of a repeater
+ detected alarm condition to the polling terminal unit occurs in the
+ same EOC message as the reporting of the current SNR Margin and Loop
+ Attenuation values, it is anticipated that this will have very little
+ impact on agent implementation.
+
+ A threshold notification occurs whenever the corresponding current
+ 15-minute interval error counter becomes equal to, or exceeds, the
+ threshold value. Only one notification SHOULD be sent per interval
+ per interface. Since the current 15-minute counter is reset to 0
+ every 15 minutes, and if the condition persists, the notification may
+ recur as often as every 15 minutes. For example, to get a
+ notification whenever a "loss of" event occurs (but at most once
+ every 15 minutes), set the corresponding threshold to 1. The agent
+ will generate a notification when the event originally occurs.
+
+ Notifications, other than the threshold notifications listed above,
+ SHOULD be rate limited (throttled) such that there is at least a
+ 1-minute gap between the generation of consecutive notifications of
+ the same event. When notifications are rate limited, they are
+ dropped and not queued for sending at a future time. This is
+ intended to be a general rate-limiting statement for notifications
+ that have no explicit rate-limiting assertions in this document
+ otherwise.
+
+ Note that the Network Management System, or NMS, may receive a
+ linkDown notification as well, if enabled (via ifLinkUpDownTrapEnable
+ [RFC2863]). At the beginning of the next 15-minute interval, the
+ counter is reset. When the first second goes by and the event
+ occurs, the current interval bucket will be 1, which equals the
+ threshold, and the notification will be sent again.
+
+ An hdsl2ShdslSpanInvalidNumRepeaters notification may be generated
+ following completion of the discovery phase if the number of
+ repeaters discovered on the line differs from the number of repeaters
+ specified in hdsl2ShdslSpanConfNumRepeaters. For those conditions
+ where the number of provisioned repeaters is greater than those
+ encountered during span discovery, all table entries associated with
+ the nonexistent repeaters are to be discarded. For those conditions
+ where the number of provisioned repeaters is less than those
+
+
+
+
+Sikes, et al. Standards Track [Page 13]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ encountered during span discovery, additional table entries are to be
+ created using the default span configuration profile.
+
+3. Definitions
+
+ HDSL2-SHDSL-LINE-MIB DEFINITIONS ::= BEGIN
+
+ IMPORTS
+ MODULE-IDENTITY,
+ OBJECT-TYPE,
+ Counter32,
+ Unsigned32,
+ Gauge32,
+ NOTIFICATION-TYPE,
+ Integer32,
+ transmission
+ FROM SNMPv2-SMI
+ RowStatus,
+ TEXTUAL-CONVENTION
+ FROM SNMPv2-TC
+ ifIndex
+ FROM IF-MIB
+ PerfCurrentCount,
+ PerfIntervalCount
+ FROM PerfHist-TC-MIB
+ SnmpAdminString
+ FROM SNMP-FRAMEWORK-MIB
+ MODULE-COMPLIANCE,
+ OBJECT-GROUP,
+ NOTIFICATION-GROUP
+ FROM SNMPv2-CONF;
+
+ hdsl2ShdslMIB MODULE-IDENTITY
+ LAST-UPDATED "200512070000Z" -- December 7, 2005
+ ORGANIZATION "ADSLMIB Working Group"
+ CONTACT-INFO "WG-email: adslmib@ietf.org
+ WG-URL:
+ http://www.ietf.org/html.charters/adslmib-charter.html
+ Info: https://www1.ietf.org/mailman/listinfo/adslmib
+ Chair: Mike Sneed
+ Sand Channel Systems
+ Postal: 1210-203 Westview Ln
+ Raleigh NC 27605 USA
+ Email: sneedmike@hotmail.com
+ Phone: +1 206 600 7022
+
+ Co-Chair Bob Ray
+ PESA Switching Systems, Inc.
+
+
+
+Sikes, et al. Standards Track [Page 14]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ Postal 330-A Wynn Drive
+ Huntsville, AL 35805 USA
+ Phone +1 256 726 9200 ext. 142
+
+ Co-editor: Clay Sikes
+ Zhone Technologies, Inc.
+ Postal: 8545 126th Ave. N.
+ Largo, FL 33772 USA
+ Email: csikes@zhone.com
+ Phone: +1 727 530 8257
+
+ Co-editor: Bob Ray
+ PESA Switching Systems, Inc.
+ Postal: 330-A Wynn Drive
+ Huntsville, AL 35805 USA
+ Email: rray@pesa.com
+ Phone: +1 256 726 9200 ext. 142
+
+ Co-editor: Rajesh Abbi
+ Alcatel USA
+ Postal: 2301 Sugar Bush Road
+ Raleigh, NC 27612-3339 USA
+
+ Email: Rajesh.Abbi@alcatel.com
+ Phone: +1 919 850 6194"
+
+ DESCRIPTION
+ "This MIB module defines a collection of objects for managing
+ HDSL2/SHDSL lines. An agent may reside at either end of the
+ line; however, the MIB module is designed to require no
+ management communication between the modems beyond that
+ inherent in the low-level EOC line protocol as defined in
+ ANSI T1E1.4/2000-006 (for HDSL2 lines) or in ITU G.991.2
+ (for SHDSL lines).
+
+ Copyright (C) The Internet Society (2005). This version of
+ this MIB module is part of RFC 4319; see the RFC itself for
+ full legal notices."
+
+ REVISION "200512070000Z" -- December 7, 2005
+ DESCRIPTION "This version, published as RFC 4319.
+ The following changes have been made in this version:
+ 1. Added a 3rd and 4th wire pair.
+ 2. Modified all rates such that their rates are only
+ constrained by an unsigned 32-bit value and not by
+ what today's perceived technology limitations are.
+
+
+
+
+
+Sikes, et al. Standards Track [Page 15]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ 3. Clarified that the rates from RFC 3276 include
+ payload and any applicable framing and added
+ objects for payload-only rates.
+ 4. Added an object to indicate whether the
+ tip and ring are reversed on a wire pair.
+ 5. Added an object to display the activation state
+ of a wire pair.
+ 6. Added references as necessary for clarification.
+ 7. Added display hints to textual conventions as
+ necessary.
+ 8. Updated conformance statements as necessary.
+ 9. Some changes were due to IETF requirements and
+ RFC generation tools."
+
+ REVISION "200205090000Z" -- May 9, 2002
+ DESCRIPTION "Initial version, published as RFC 3276."
+
+ ::= { transmission 48 }
+
+ hdsl2ShdslMibObjects OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 1 }
+
+ -- Textual Conventions used in this MIB module
+ --
+
+ Hdsl2ShdslPerfCurrDayCount ::= TEXTUAL-CONVENTION
+ DISPLAY-HINT "d"
+ STATUS current
+ DESCRIPTION
+ "A gauge associated with interface performance measurements in
+ a current 1-day (24 hour) measurement interval.
+
+ The value of this gauge starts at zero at the beginning of an
+ interval and is increased when associated events occur, until
+ the end of the 1-day interval. At that time, the value of the
+ gauge is stored in the previous 1-day history interval, as
+ defined in a companion object of type
+ Hdsl2Shdsl1DayIntevalCount, and the current interval gauge
+ is restarted at zero.
+
+ In the case where the agent has no valid data available for
+ this interval, the corresponding object instance is not
+ available, and upon a retrieval request, a corresponding error
+ message shall be returned to indicate that this instance does
+ not exist. Please note that zero is a valid value."
+ SYNTAX Gauge32
+
+ Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION
+ DISPLAY-HINT "d"
+
+
+
+Sikes, et al. Standards Track [Page 16]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ STATUS current
+ DESCRIPTION
+ "A counter associated with interface performance measurements
+ during the most previous 1-day (24 hour) measurement interval.
+ The value of this gauge is equal to the value of the current
+ day gauge, as defined in a companion object of type
+ Hdsl2ShdslPerfCurrDayCount, at the end of its most recent
+ interval.
+
+ In the case where the agent has no valid data available for
+ this interval, the corresponding object instance is not
+ available, and upon a retrieval request, a corresponding error
+ message shall be returned to indicate that this instance does
+ not exist."
+ SYNTAX Gauge32
+
+ Hdsl2ShdslPerfTimeElapsed ::= TEXTUAL-CONVENTION
+ DISPLAY-HINT "d"
+ STATUS current
+ DESCRIPTION
+ "The number of seconds that have elapsed since the beginning of
+ the current measurement period. If, for some reason, such as
+ an adjustment in the system's time-of-day clock or the addition
+ of a leap second, the current interval exceeds the maximum
+ value, the agent will return the maximum value.
+
+ For 15-minute intervals, the range is limited to (0..899).
+ For 24-hour intervals, the range is limited to (0..86399)."
+ SYNTAX Unsigned32(0..86399)
+
+ Hdsl2ShdslPerfIntervalThreshold ::= TEXTUAL-CONVENTION
+ DISPLAY-HINT "d"
+ STATUS current
+ DESCRIPTION
+ "This convention defines a range of values that may be set in
+ a fault threshold alarm control. As the number of seconds in
+ a 15-minute interval numbers at most 900, objects of this type
+ may have a range of 0...900, where the value of 0 disables the
+ alarm."
+ SYNTAX Unsigned32(0..900)
+
+ Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "This is the unique identification for all units in an
+ HDSL2/SHDSL span. It is based on the EOC unit addressing
+ scheme with reference to the xtuC."
+ SYNTAX INTEGER
+
+
+
+Sikes, et al. Standards Track [Page 17]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ {
+ xtuC(1),
+ xtuR(2),
+ xru1(3),
+ xru2(4),
+ xru3(5),
+ xru4(6),
+ xru5(7),
+ xru6(8),
+ xru7(9),
+ xru8(10)
+ }
+
+ Hdsl2ShdslUnitSide ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "This is the referenced side of an HDSL2/SHDSL unit - Network
+ or Customer side. The side facing the Network is the Network
+ side, while the side facing the Customer is the Customer side."
+ SYNTAX INTEGER
+ {
+ networkSide(1),
+ customerSide(2)
+ }
+
+ Hdsl2ShdslWirePair ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "This is the referenced pair of wires in an HDSL2/SHDSL segment.
+ HDSL2 only supports a single pair (wirePair1 or two wire),
+ SHDSL lines support an optional second pair (wirePair2 or four
+ wire), and G.shdsl.bis support an optional third pair
+ (wirePair3 or six wire) and an optional fourth pair
+ (wirePair4 or eight wire)."
+ SYNTAX INTEGER
+ {
+ wirePair1(1), -- two wire
+ wirePair2(2), -- four wire
+ wirePair3(3), -- six wire
+ wirePair4(4) -- eight wire
+ }
+
+ Hdsl2ShdslTransmissionModeType ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "Contains the regional setting of the HDSL2/SHDSL span,
+ represented as a bit-map of possible settings. The various
+ bit positions are as follows:
+
+
+
+Sikes, et al. Standards Track [Page 18]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ Bit Meaning Description
+ 1 region 1 Indicates ITU-T G.991.2 Annex A.
+ 2 region 2 Indicates ITU-T G.991.2 Annex B."
+ SYNTAX BITS
+ {
+ region1(0),
+ region2(1)
+ }
+
+ Hdsl2ShdslClockReferenceType ::= TEXTUAL-CONVENTION
+ STATUS current
+ DESCRIPTION
+ "The various STU-C symbol clock references for the
+ HDSL2/SHDSL span, represented as an enumeration."
+ SYNTAX INTEGER
+ {
+ localClk(1), -- Mode-1 per G991.2
+ networkClk(2), -- Mode-2 per G991.2
+ dataOrNetworkClk(3), -- Mode-3a per G991.2
+ dataClk(4) -- Mode-3b per G991.2
+ }
+
+ -- Span Configuration Group
+ --
+
+ hdsl2ShdslSpanConfTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+
+ DESCRIPTION
+ "This table supports overall configuration of HDSL2/SHDSL
+ spans. Entries in this table MUST be maintained in a
+ persistent manner."
+ ::= { hdsl2ShdslMibObjects 1 }
+
+ hdsl2ShdslSpanConfEntry OBJECT-TYPE
+ SYNTAX Hdsl2ShdslSpanConfEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "An entry in the hdsl2ShdslSpanConfTable. Each entry
+ represents the complete span in a single HDSL2/SHDSL line.
+ It is indexed by the ifIndex of the associated HDSL2/SHDSL
+ line."
+ INDEX { ifIndex }
+ ::= { hdsl2ShdslSpanConfTable 1 }
+
+
+
+
+Sikes, et al. Standards Track [Page 19]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ Hdsl2ShdslSpanConfEntry ::=
+ SEQUENCE
+ {
+ hdsl2ShdslSpanConfNumRepeaters Unsigned32,
+ hdsl2ShdslSpanConfProfile SnmpAdminString,
+ hdsl2ShdslSpanConfAlarmProfile SnmpAdminString
+ }
+
+ hdsl2ShdslSpanConfNumRepeaters OBJECT-TYPE
+ SYNTAX Unsigned32(0..8)
+ UNITS "repeaters"
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object provisions the number of repeaters/regenerators
+ in this HDSL2/SHDSL span."
+ ::= { hdsl2ShdslSpanConfEntry 1 }
+
+ hdsl2ShdslSpanConfProfile OBJECT-TYPE
+ SYNTAX SnmpAdminString (SIZE(1..32))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object is a pointer to a span configuration profile in
+ the hdsl2ShdslSpanConfProfileTable, which applies to this
+ span. The value of this object is the index of the referenced
+ profile in the hdsl2ShdslSpanConfProfileTable. Note that span
+ configuration profiles are only applicable to SHDSL lines.
+
+ HDSL2 lines MUST reference the default profile, 'DEFVAL'.
+ By default, this object will have the value 'DEFVAL'
+ (the index of the default profile).
+
+ Any attempt to set this object to a value that is not the value
+ of the index for an active entry in the profile table,
+ hdsl2ShdslSpanConfProfileTable, MUST be rejected."
+ ::= { hdsl2ShdslSpanConfEntry 2 }
+
+ hdsl2ShdslSpanConfAlarmProfile OBJECT-TYPE
+ SYNTAX SnmpAdminString (SIZE(1..32))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object is a pointer to an alarm configuration profile in
+ the hdsl2ShdslEndpointAlarmConfProfileTable. The value of
+ this object is the index of the referenced profile in the
+ hdsl2ShdslEndpointAlarmConfProfileTable. The alarm
+ threshold configuration in the referenced profile will be
+
+
+
+Sikes, et al. Standards Track [Page 20]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ used by default for all segment endpoints in this span.
+ Individual endpoints may override this profile by explicitly
+ specifying some other profile in the
+ hdsl2ShdslEndpointConfTable. By default, this object will
+ have the value 'DEFVAL' (the index of the default
+ profile).
+
+ Any attempt to set this object to a value that is not the value
+ of the index for an active entry in the profile table,
+ hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
+ ::= { hdsl2ShdslSpanConfEntry 3 }
+
+ -- Span Status Group
+ --
+
+ hdsl2ShdslSpanStatusTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Hdsl2ShdslSpanStatusEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table provides overall status information of
+ HDSL2/SHDSL spans. This table contains live data from
+ equipment. As such, it is NOT persistent."
+ ::= { hdsl2ShdslMibObjects 2 }
+
+ hdsl2ShdslSpanStatusEntry OBJECT-TYPE
+ SYNTAX Hdsl2ShdslSpanStatusEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "An entry in the hdsl2ShdslSpanStatusTable. Each entry
+ represents the complete span in a single HDSL2/SHDSL line.
+ It is indexed by the ifIndex of the associated HDSL2/SHDSL
+ line."
+ INDEX { ifIndex }
+ ::= { hdsl2ShdslSpanStatusTable 1 }
+
+ Hdsl2ShdslSpanStatusEntry ::=
+ SEQUENCE
+ {
+ hdsl2ShdslStatusNumAvailRepeaters Unsigned32,
+ hdsl2ShdslStatusMaxAttainableLineRate Unsigned32,
+ hdsl2ShdslStatusActualLineRate Unsigned32,
+ hdsl2ShdslStatusTransmissionModeCurrent
+ Hdsl2ShdslTransmissionModeType,
+ hdsl2ShdslStatusMaxAttainablePayloadRate Unsigned32,
+ hdsl2ShdslStatusActualPayloadRate Unsigned32
+ }
+
+
+
+Sikes, et al. Standards Track [Page 21]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE
+ SYNTAX Unsigned32(0..8)
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Contains the actual number of repeaters/regenerators
+ discovered in this HDSL2/SHDSL span."
+ ::= { hdsl2ShdslSpanStatusEntry 1 }
+
+ hdsl2ShdslStatusMaxAttainableLineRate OBJECT-TYPE
+ SYNTAX Unsigned32(0..4294967295)
+ UNITS "bps"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Contains the maximum attainable line rate in this HDSL2/SHDSL
+ span. This object provides the maximum rate the line is
+ capable of achieving. This is based upon measurements made
+ during line probing. This rate includes payload (user data)
+ and any applicable framing overhead."
+ ::= { hdsl2ShdslSpanStatusEntry 2 }
+
+ hdsl2ShdslStatusActualLineRate OBJECT-TYPE
+ SYNTAX Unsigned32(0..4294967295)
+ UNITS "bps"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Contains the actual line rate in this HDSL2/SHDSL span. This
+ SHOULD equal ifSpeed. This rate includes payload (user data)
+ and any applicable framing overhead"
+ ::= { hdsl2ShdslSpanStatusEntry 3 }
+
+ hdsl2ShdslStatusTransmissionModeCurrent OBJECT-TYPE
+ SYNTAX Hdsl2ShdslTransmissionModeType
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Contains the current Power Spectral Density (PSD) regional
+ setting of the HDSL2/SHDSL span."
+ ::= { hdsl2ShdslSpanStatusEntry 4 }
+
+ hdsl2ShdslStatusMaxAttainablePayloadRate OBJECT-TYPE
+ SYNTAX Unsigned32(0..4294967295)
+ UNITS "bps"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+
+
+
+Sikes, et al. Standards Track [Page 22]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ "Contains the maximum attainable payload (user data)
+ line rate in this HDSL2/SHDSL span. This object provides
+ the maximum rate the line is capable of achieving. This
+ is based upon measurements made during line probing. Any
+ framing overhead is not included."
+ ::= { hdsl2ShdslSpanStatusEntry 5 }
+
+ hdsl2ShdslStatusActualPayloadRate OBJECT-TYPE
+ SYNTAX Unsigned32(0..4294967295)
+ UNITS "bps"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Contains the actual line rate in this HDSL2/SHDSL span. Any
+ framing overhead is not included."
+ ::= { hdsl2ShdslSpanStatusEntry 6 }
+
+ -- Unit Inventory Group
+ --
+
+ hdsl2ShdslInventoryTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Hdsl2ShdslInventoryEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table supports retrieval of unit inventory information
+ available via the EOC from units in an HDSL2/SHDSL line.
+
+ Entries in this table are dynamically created during the
+ line discovery process. The life cycle for these entries
+ is as follows:
+
+ - xtu discovers a device, either a far-end xtu or an xru
+ - an inventory table entry is created for the device
+ - the line goes down for whatever reason
+ - inventory table entries for unreachable devices are
+ destroyed
+
+ As these entries are created/destroyed dynamically, they
+ are NOT persistent."
+ ::= { hdsl2ShdslMibObjects 3 }
+
+ hdsl2ShdslInventoryEntry OBJECT-TYPE
+ SYNTAX Hdsl2ShdslInventoryEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "An entry in the hdsl2ShdslInventoryTable. Each entry
+
+
+
+Sikes, et al. Standards Track [Page 23]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ represents inventory information for a single unit in an
+ HDSL2/SHDSL line. It is indexed by the ifIndex of the
+ HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the
+ associated unit."
+ INDEX { ifIndex, hdsl2ShdslInvIndex }
+ ::= { hdsl2ShdslInventoryTable 1 }
+
+ Hdsl2ShdslInventoryEntry ::=
+ SEQUENCE
+ {
+ hdsl2ShdslInvIndex Hdsl2ShdslUnitId,
+ hdsl2ShdslInvVendorID OCTET STRING,
+ hdsl2ShdslInvVendorModelNumber OCTET STRING,
+ hdsl2ShdslInvVendorSerialNumber OCTET STRING,
+ hdsl2ShdslInvVendorEOCSoftwareVersion Integer32,
+ hdsl2ShdslInvStandardVersion Integer32,
+ hdsl2ShdslInvVendorListNumber OCTET STRING,
+ hdsl2ShdslInvVendorIssueNumber OCTET STRING,
+ hdsl2ShdslInvVendorSoftwareVersion OCTET STRING,
+ hdsl2ShdslInvEquipmentCode OCTET STRING,
+ hdsl2ShdslInvVendorOther OCTET STRING,
+ hdsl2ShdslInvTransmissionModeCapability
+ Hdsl2ShdslTransmissionModeType
+ }
+
+ hdsl2ShdslInvIndex OBJECT-TYPE
+ SYNTAX Hdsl2ShdslUnitId
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry in this table corresponds to a physical element
+ in an HDSL2/SHDSL span. It is based on the EOC unit addressing
+ scheme with reference to the xtuC."
+ ::= { hdsl2ShdslInventoryEntry 1 }
+
+ hdsl2ShdslInvVendorID OBJECT-TYPE
+ SYNTAX OCTET STRING(SIZE(8))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Vendor ID as reported in an Inventory Response message."
+ REFERENCE
+ "G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
+ 130, Octets 25-32."
+ ::= { hdsl2ShdslInventoryEntry 2 }
+
+ hdsl2ShdslInvVendorModelNumber OBJECT-TYPE
+ SYNTAX OCTET STRING(SIZE(12))
+
+
+
+Sikes, et al. Standards Track [Page 24]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Vendor model number as reported in an Inventory Response
+ message."
+ REFERENCE
+ "G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
+ 130, Octets 33-44."
+ ::= { hdsl2ShdslInventoryEntry 3 }
+
+ hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE
+ SYNTAX OCTET STRING(SIZE(12))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Vendor serial number as reported in an Inventory Response
+ message."
+ REFERENCE
+ "G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
+ 130, Octets 45-56."
+ ::= { hdsl2ShdslInventoryEntry 4 }
+
+ hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Vendor EOC version as reported in a Discovery Response
+ message."
+ REFERENCE
+ "G.991.2, Section 9.5.5.7.2, Discovery response - Message ID
+ 129, Octet 12."
+ ::= { hdsl2ShdslInventoryEntry 5 }
+
+ hdsl2ShdslInvStandardVersion OBJECT-TYPE
+ SYNTAX Integer32
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Version of the HDSL2/SHDSL standard implemented, as reported
+ in an Inventory Response message."
+ REFERENCE
+ "G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
+ 130, Octet 2."
+ ::= { hdsl2ShdslInventoryEntry 6 }
+
+ hdsl2ShdslInvVendorListNumber OBJECT-TYPE
+ SYNTAX OCTET STRING(SIZE(3))
+
+
+
+Sikes, et al. Standards Track [Page 25]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Vendor list number as reported in an Inventory Response
+ message."
+ REFERENCE
+ "G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
+ 130, Octets 3-5."
+ ::= { hdsl2ShdslInventoryEntry 7 }
+
+ hdsl2ShdslInvVendorIssueNumber OBJECT-TYPE
+ SYNTAX OCTET STRING(SIZE(2))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Vendor issue number as reported in an Inventory Response
+ message."
+ REFERENCE
+ "G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
+ 130, Octets 6-7."
+ ::= { hdsl2ShdslInventoryEntry 8 }
+
+ hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE
+ SYNTAX OCTET STRING(SIZE(6))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Vendor software version as reported in an Inventory Response
+ message."
+ REFERENCE
+ "G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
+ 130, Octets 8-13."
+ ::= { hdsl2ShdslInventoryEntry 9 }
+
+ hdsl2ShdslInvEquipmentCode OBJECT-TYPE
+ SYNTAX OCTET STRING(SIZE(10))
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Equipment code conforming to ANSI T1.213, Coded Identification
+ of Equipment Entities."
+ REFERENCE
+ "G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
+ 130, Octets 14-23."
+ ::= { hdsl2ShdslInventoryEntry 10 }
+
+ hdsl2ShdslInvVendorOther OBJECT-TYPE
+ SYNTAX OCTET STRING(SIZE(12))
+
+
+
+Sikes, et al. Standards Track [Page 26]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Other vendor information as reported in an Inventory Response
+ message."
+ REFERENCE
+ "G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
+ 130, Octets 57-68."
+ ::= { hdsl2ShdslInventoryEntry 11 }
+
+ hdsl2ShdslInvTransmissionModeCapability OBJECT-TYPE
+ SYNTAX Hdsl2ShdslTransmissionModeType
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Contains the transmission mode capability of the SHDSL unit."
+ ::= { hdsl2ShdslInventoryEntry 12 }
+
+ -- Segment Endpoint Configuration Group
+ --
+
+ hdsl2ShdslEndpointConfTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Hdsl2ShdslEndpointConfEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table supports configuration parameters for segment
+ endpoints in an HDSL2/SHDSL line. As this table is indexed
+ by ifIndex, it MUST be maintained in a persistent manner."
+ ::= { hdsl2ShdslMibObjects 4 }
+
+ hdsl2ShdslEndpointConfEntry OBJECT-TYPE
+ SYNTAX Hdsl2ShdslEndpointConfEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "An entry in the hdsl2ShdslEndpointConfTable. Each entry
+ represents a single segment endpoint in an HDSL2/SHDSL line.
+ It is indexed by the ifIndex of the HDSL2/SHDSL line, the
+ UnitId of the associated unit, the side of the unit, and the
+ wire pair of the associated modem."
+ INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
+ hdsl2ShdslEndpointWirePair}
+ ::= { hdsl2ShdslEndpointConfTable 1 }
+
+ Hdsl2ShdslEndpointConfEntry ::=
+ SEQUENCE
+ {
+
+
+
+Sikes, et al. Standards Track [Page 27]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide,
+ hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair,
+ hdsl2ShdslEndpointAlarmConfProfile SnmpAdminString
+ }
+
+ hdsl2ShdslEndpointSide OBJECT-TYPE
+ SYNTAX Hdsl2ShdslUnitSide
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "The side of the unit associated with this segment endpoint --
+ Network/Customer side -- as per the Hdsl2ShdslUnitSide textual
+ convention."
+ ::= { hdsl2ShdslEndpointConfEntry 1 }
+
+ hdsl2ShdslEndpointWirePair OBJECT-TYPE
+ SYNTAX Hdsl2ShdslWirePair
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "The wire pair of the modem associated with this segment
+ endpoint as per the Hdsl2ShdslWirePair textual convention."
+ ::= { hdsl2ShdslEndpointConfEntry 2 }
+
+ hdsl2ShdslEndpointAlarmConfProfile OBJECT-TYPE
+ SYNTAX SnmpAdminString (SIZE(0..32))
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object configures the alarm threshold values to be used
+ for this segment endpoint. The values are obtained from the
+ alarm configuration profile referenced by this object. The
+ value of this object is the index of the referenced profile in
+ the hdsl2ShdslEndpointAlarmConfProfileTable, or NULL (a
+ zero-length SnmpAdminString). If the value is a zero-length
+ SnmpAdminString, the endpoint uses the default Alarm
+ Configuration Profile for the associated span as per the
+ hdsl2ShdslSpanConfAlarmProfile object in the
+ hdsl2ShdslSpanConfTable. The default value of this object is
+ a zero-length SnmpAdminString.
+
+ Any attempt to set this object to a value that is not the value
+ of the index for an active entry in the profile table,
+ hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
+ ::= { hdsl2ShdslEndpointConfEntry 3 }
+
+ -- Segment Endpoint Current Status/Performance Group
+ --
+
+
+
+Sikes, et al. Standards Track [Page 28]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ hdsl2ShdslEndpointCurrTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table contains current status and performance information
+ for segment endpoints in HDSL2/SHDSL lines. As with other
+ tables in this MIB module indexed by ifIndex, entries in this
+ table MUST be maintained in a persistent manner."
+ ::= { hdsl2ShdslMibObjects 5 }
+
+ hdsl2ShdslEndpointCurrEntry OBJECT-TYPE
+ SYNTAX Hdsl2ShdslEndpointCurrEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "An entry in the hdsl2ShdslEndpointCurrTable. Each entry
+ contains status and performance information relating to a
+ single segment endpoint. It is indexed by the ifIndex of the
+ HDSL2/SHDSL line, the UnitId of the associated unit, the side
+ of the unit, and the wire pair of the associated modem."
+ INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
+ hdsl2ShdslEndpointWirePair }
+ ::= { hdsl2ShdslEndpointCurrTable 1 }
+
+ Hdsl2ShdslEndpointCurrEntry ::=
+ SEQUENCE
+ {
+ hdsl2ShdslEndpointCurrAtn Integer32,
+ hdsl2ShdslEndpointCurrSnrMgn Integer32,
+ hdsl2ShdslEndpointCurrStatus BITS,
+ hdsl2ShdslEndpointES Counter32,
+ hdsl2ShdslEndpointSES Counter32,
+ hdsl2ShdslEndpointCRCanomalies Counter32,
+ hdsl2ShdslEndpointLOSWS Counter32,
+ hdsl2ShdslEndpointUAS Counter32,
+ hdsl2ShdslEndpointCurr15MinTimeElapsed
+ Hdsl2ShdslPerfTimeElapsed,
+ hdsl2ShdslEndpointCurr15MinES PerfCurrentCount,
+ hdsl2ShdslEndpointCurr15MinSES PerfCurrentCount,
+ hdsl2ShdslEndpointCurr15MinCRCanomalies PerfCurrentCount,
+ hdsl2ShdslEndpointCurr15MinLOSWS PerfCurrentCount,
+ hdsl2ShdslEndpointCurr15MinUAS PerfCurrentCount,
+ hdsl2ShdslEndpointCurr1DayTimeElapsed
+ Hdsl2ShdslPerfTimeElapsed,
+ hdsl2ShdslEndpointCurr1DayES
+ Hdsl2ShdslPerfCurrDayCount,
+ hdsl2ShdslEndpointCurr1DaySES
+
+
+
+Sikes, et al. Standards Track [Page 29]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ Hdsl2ShdslPerfCurrDayCount,
+ hdsl2ShdslEndpointCurr1DayCRCanomalies
+ Hdsl2ShdslPerfCurrDayCount,
+ hdsl2ShdslEndpointCurr1DayLOSWS
+ Hdsl2ShdslPerfCurrDayCount,
+ hdsl2ShdslEndpointCurr1DayUAS
+ Hdsl2ShdslPerfCurrDayCount,
+ hdsl2ShdslEndpointCurrTipRingReversal INTEGER,
+ hdsl2ShdslEndpointCurrActivationState INTEGER
+ }
+
+ hdsl2ShdslEndpointCurrAtn OBJECT-TYPE
+ SYNTAX Integer32(-127..128)
+ UNITS "dB"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The current loop attenuation for this endpoint as reported in
+ a Network or Customer Side Performance Status message."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 1 }
+
+ hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE
+ SYNTAX Integer32(-127..128)
+ UNITS "dB"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The current SNR margin for this endpoint as reported in a
+ Status Response/SNR message."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 2 }
+
+ hdsl2ShdslEndpointCurrStatus OBJECT-TYPE
+ SYNTAX BITS
+ {
+ noDefect(0),
+ powerBackoff(1),
+ deviceFault(2),
+ dcContinuityFault(3),
+ snrMarginAlarm(4),
+ loopAttenuationAlarm(5),
+ loswFailureAlarm(6),
+ configInitFailure(7),
+ protocolInitFailure(8),
+ noNeighborPresent(9),
+ loopbackActive(10)
+ }
+
+
+
+Sikes, et al. Standards Track [Page 30]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Contains the current state of the endpoint. This is a
+ bit-map of possible conditions. The various bit positions
+ are as follows:
+
+ noDefect There are no defects on the line.
+
+ powerBackoff Indicates enhanced Power Backoff.
+
+ deviceFault Indicates that a vendor-dependent
+ diagnostic or self-test fault
+ has been detected.
+
+ dcContinuityFault Indicates vendor-dependent
+ conditions that interfere with
+ span powering such as short and
+ open circuits.
+
+ snrMarginAlarm Indicates that the SNR margin
+ has dropped below the alarm threshold.
+
+ loopAttenuationAlarm Indicates that the loop attenuation
+ exceeds the alarm threshold.
+
+ loswFailureAlarm Indicates a forward LOSW alarm.
+
+ configInitFailure Endpoint failure during initialization
+ due to paired endpoint not able to
+ support requested configuration.
+
+ protocolInitFailure Endpoint failure during initialization
+ due to incompatible protocol used by
+ the paired endpoint.
+
+ noNeighborPresent Endpoint failure during initialization
+ due to no activation sequence detected
+ from paired endpoint.
+
+ loopbackActive A loopback is currently active at this
+ segment endpoint.
+
+ This is intended to supplement ifOperStatus. Note that there
+ is a 1:1 relationship between the status bits defined in this
+ object and the notification thresholds defined elsewhere in
+ this MIB module."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+
+
+
+Sikes, et al. Standards Track [Page 31]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ ::= { hdsl2ShdslEndpointCurrEntry 3 }
+
+ hdsl2ShdslEndpointES OBJECT-TYPE
+ SYNTAX Counter32
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Errored Seconds (ES) on this endpoint since the xU
+ was last restarted."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 4 }
+
+ hdsl2ShdslEndpointSES OBJECT-TYPE
+ SYNTAX Counter32
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Severely Errored Seconds (SES) on this endpoint
+ since the xU was last restarted."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 5 }
+
+ hdsl2ShdslEndpointCRCanomalies OBJECT-TYPE
+ SYNTAX Counter32
+ UNITS "detected CRC Anomalies"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of CRC anomalies on this endpoint since the xU was
+ last restarted."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 6 }
+
+ hdsl2ShdslEndpointLOSWS OBJECT-TYPE
+ SYNTAX Counter32
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Loss of Sync Word (LOSW) Seconds on this endpoint
+ since the xU was last restarted."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 7 }
+
+ hdsl2ShdslEndpointUAS OBJECT-TYPE
+ SYNTAX Counter32
+
+
+
+Sikes, et al. Standards Track [Page 32]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Unavailable Seconds (UAS) on this endpoint since
+ the xU was last restarted."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 8 }
+
+ hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE
+ SYNTAX Hdsl2ShdslPerfTimeElapsed
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Total elapsed seconds in the current 15-minute interval."
+ ::= { hdsl2ShdslEndpointCurrEntry 9 }
+
+ hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE
+ SYNTAX PerfCurrentCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Errored Seconds (ES) in the current 15-minute
+ interval."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 10 }
+
+ hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPE
+ SYNTAX PerfCurrentCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Severely Errored Seconds (SES) in the current
+ 15-minute interval."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 11 }
+
+ hdsl2ShdslEndpointCurr15MinCRCanomalies OBJECT-TYPE
+ SYNTAX PerfCurrentCount
+ UNITS "detected CRC Anomalies"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of CRC anomalies in the current 15-minute interval."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+
+
+
+Sikes, et al. Standards Track [Page 33]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ ::= { hdsl2ShdslEndpointCurrEntry 12 }
+
+ hdsl2ShdslEndpointCurr15MinLOSWS OBJECT-TYPE
+ SYNTAX PerfCurrentCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Loss of Sync Word (LOSW) Seconds in the current
+ 15-minute interval."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 13 }
+
+ hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE
+ SYNTAX PerfCurrentCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Unavailable Seconds (UAS) in the current 15-minute
+ interval."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 14 }
+
+ hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE
+ SYNTAX Hdsl2ShdslPerfTimeElapsed
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Number of seconds that have elapsed since the beginning of
+ the current 1-day interval."
+ ::= { hdsl2ShdslEndpointCurrEntry 15 }
+
+ hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE
+ SYNTAX Hdsl2ShdslPerfCurrDayCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Errored Seconds (ES) during the current day as
+ measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 16 }
+
+ hdsl2ShdslEndpointCurr1DaySES OBJECT-TYPE
+ SYNTAX Hdsl2ShdslPerfCurrDayCount
+ UNITS "seconds"
+
+
+
+Sikes, et al. Standards Track [Page 34]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Severely Errored Seconds (SES) during the current
+ day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 17 }
+
+ hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPE
+ SYNTAX Hdsl2ShdslPerfCurrDayCount
+ UNITS "detected CRC Anomalies"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of CRC anomalies during the current day as measured
+ by hdsl2ShdslEndpointCurr1DayTimeElapsed."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 18 }
+
+ hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE
+ SYNTAX Hdsl2ShdslPerfCurrDayCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Loss of Sync Word (LOSW) Seconds during the current
+ day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 19 }
+
+ hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE
+ SYNTAX Hdsl2ShdslPerfCurrDayCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Unavailable Seconds (UAS) during the current day as
+ measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2ShdslEndpointCurrEntry 20 }
+
+ hdsl2ShdslEndpointCurrTipRingReversal OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ normal(1),
+ reversed(2)
+ }
+ MAX-ACCESS read-only
+
+
+
+Sikes, et al. Standards Track [Page 35]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ STATUS current
+ DESCRIPTION
+ "This object indicates the state of the tip/ring for the
+ wire pair."
+ ::= { hdsl2ShdslEndpointCurrEntry 21 }
+
+ hdsl2ShdslEndpointCurrActivationState OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ preActivation(1), -- PreTrain
+ activation(2), -- Training
+ data(3) -- Trained
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object indicates the activation or training state of
+ the wire pair."
+ REFERENCE "ITU-T G.991.2, Section 6.2 PMD Activation Sequence"
+ ::= { hdsl2ShdslEndpointCurrEntry 22 }
+
+ -- Segment Endpoint 15-Minute Interval Status/Performance Group
+ --
+
+ hdsl2Shdsl15MinIntervalTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table provides one row for each HDSL2/SHDSL endpoint
+ performance data collection interval. This table contains
+ live data from equipment. As such, it is NOT persistent."
+ ::= { hdsl2ShdslMibObjects 6 }
+
+ hdsl2Shdsl15MinIntervalEntry OBJECT-TYPE
+ SYNTAX Hdsl2Shdsl15MinIntervalEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "An entry in the hdsl2Shdsl15MinIntervalTable."
+ INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
+ hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}
+ ::= { hdsl2Shdsl15MinIntervalTable 1 }
+
+ Hdsl2Shdsl15MinIntervalEntry ::=
+ SEQUENCE
+ {
+ hdsl2Shdsl15MinIntervalNumber Unsigned32,
+
+
+
+Sikes, et al. Standards Track [Page 36]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ hdsl2Shdsl15MinIntervalES PerfIntervalCount,
+ hdsl2Shdsl15MinIntervalSES PerfIntervalCount,
+ hdsl2Shdsl15MinIntervalCRCanomalies PerfIntervalCount,
+ hdsl2Shdsl15MinIntervalLOSWS PerfIntervalCount,
+ hdsl2Shdsl15MinIntervalUAS PerfIntervalCount
+ }
+
+ hdsl2Shdsl15MinIntervalNumber OBJECT-TYPE
+ SYNTAX Unsigned32(1..96)
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Performance Data Interval number. Interval 1 is the most
+ recent previous interval; interval 96 is 24 hours ago.
+ Intervals 2..96 are optional."
+ ::= { hdsl2Shdsl15MinIntervalEntry 1 }
+
+ hdsl2Shdsl15MinIntervalES OBJECT-TYPE
+ SYNTAX PerfIntervalCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Errored Seconds (ES) during the interval."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2Shdsl15MinIntervalEntry 2 }
+
+ hdsl2Shdsl15MinIntervalSES OBJECT-TYPE
+ SYNTAX PerfIntervalCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Severely Errored Seconds (SES) during the interval."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2Shdsl15MinIntervalEntry 3 }
+
+ hdsl2Shdsl15MinIntervalCRCanomalies OBJECT-TYPE
+ SYNTAX PerfIntervalCount
+ UNITS "detected CRC Anomalies"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of CRC anomalies during the interval."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2Shdsl15MinIntervalEntry 4 }
+
+ hdsl2Shdsl15MinIntervalLOSWS OBJECT-TYPE
+
+
+
+Sikes, et al. Standards Track [Page 37]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ SYNTAX PerfIntervalCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Loss of Sync Word (LOSW) Seconds during the
+ interval."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2Shdsl15MinIntervalEntry 5 }
+
+ hdsl2Shdsl15MinIntervalUAS OBJECT-TYPE
+ SYNTAX PerfIntervalCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Unavailable Seconds (UAS) during the interval."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2Shdsl15MinIntervalEntry 6 }
+
+ -- Segment Endpoint 1-Day Interval Status/Performance Group
+ --
+
+ hdsl2Shdsl1DayIntervalTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table provides one row for each HDSL2/SHDSL endpoint
+ performance data collection interval. This table contains
+ live data from equipment. As such, it is NOT persistent."
+ ::= { hdsl2ShdslMibObjects 7 }
+
+ hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE
+ SYNTAX Hdsl2Shdsl1DayIntervalEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "An entry in the hdsl2Shdsl1DayIntervalTable."
+ INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
+ hdsl2ShdslEndpointWirePair, hdsl2Shdsl1DayIntervalNumber }
+ ::= { hdsl2Shdsl1DayIntervalTable 1 }
+
+ Hdsl2Shdsl1DayIntervalEntry ::=
+ SEQUENCE
+ {
+ hdsl2Shdsl1DayIntervalNumber Unsigned32,
+ hdsl2Shdsl1DayIntervalMoniSecs Hdsl2ShdslPerfTimeElapsed,
+
+
+
+Sikes, et al. Standards Track [Page 38]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ hdsl2Shdsl1DayIntervalES Hdsl2Shdsl1DayIntervalCount,
+ hdsl2Shdsl1DayIntervalSES Hdsl2Shdsl1DayIntervalCount,
+ hdsl2Shdsl1DayIntervalCRCanomalies Hdsl2Shdsl1DayIntervalCount,
+ hdsl2Shdsl1DayIntervalLOSWS Hdsl2Shdsl1DayIntervalCount,
+ hdsl2Shdsl1DayIntervalUAS Hdsl2Shdsl1DayIntervalCount
+ }
+
+ hdsl2Shdsl1DayIntervalNumber OBJECT-TYPE
+ SYNTAX Unsigned32(1..30)
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "History Data Interval number. Interval 1 is the most
+ recent previous day; interval 30 is 30 days ago. Intervals
+ 2..30 are optional."
+ ::= { hdsl2Shdsl1DayIntervalEntry 1 }
+
+ hdsl2Shdsl1DayIntervalMoniSecs OBJECT-TYPE
+ SYNTAX Hdsl2ShdslPerfTimeElapsed
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "The amount of time in the 1-day interval over which the
+ performance monitoring information is actually counted.
+ This value will be the same as the interval duration except
+ in a situation where performance monitoring data could not
+ be collected for any reason."
+ ::= { hdsl2Shdsl1DayIntervalEntry 2 }
+
+ hdsl2Shdsl1DayIntervalES OBJECT-TYPE
+ SYNTAX Hdsl2Shdsl1DayIntervalCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Errored Seconds (ES) during the 1-day interval as
+ measured by hdsl2Shdsl1DayIntervalMoniSecs."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2Shdsl1DayIntervalEntry 3 }
+
+ hdsl2Shdsl1DayIntervalSES OBJECT-TYPE
+ SYNTAX Hdsl2Shdsl1DayIntervalCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Severely Errored Seconds (SES) during the 1-day
+
+
+
+Sikes, et al. Standards Track [Page 39]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2Shdsl1DayIntervalEntry 4 }
+
+ hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPE
+ SYNTAX Hdsl2Shdsl1DayIntervalCount
+ UNITS "detected CRC Anomalies"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of CRC anomalies during the 1-day interval as
+ measured by hdsl2Shdsl1DayIntervalMoniSecs."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2Shdsl1DayIntervalEntry 5 }
+
+ hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPE
+ SYNTAX Hdsl2Shdsl1DayIntervalCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Loss of Sync Word (LOSW) Seconds during the 1-day
+ interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2Shdsl1DayIntervalEntry 6 }
+
+ hdsl2Shdsl1DayIntervalUAS OBJECT-TYPE
+ SYNTAX Hdsl2Shdsl1DayIntervalCount
+ UNITS "seconds"
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "Count of Unavailable Seconds (UAS) during the 1-day interval
+ as measured by hdsl2Shdsl1DayIntervalMoniSecs."
+ REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
+ ::= { hdsl2Shdsl1DayIntervalEntry 7 }
+
+ -- Maintenance Group
+ --
+
+ hdsl2ShdslEndpointMaintTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Hdsl2ShdslEndpointMaintEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table supports maintenance operations (e.g., loopbacks)
+ to be performed on HDSL2/SHDSL segment endpoints. This table
+ contains live data from equipment. As such, it is NOT
+
+
+
+Sikes, et al. Standards Track [Page 40]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ persistent."
+ ::= { hdsl2ShdslMibObjects 8 }
+
+ hdsl2ShdslEndpointMaintEntry OBJECT-TYPE
+ SYNTAX Hdsl2ShdslEndpointMaintEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "An entry in the hdsl2ShdslEndpointMaintTable. Each entry
+ corresponds to a single segment endpoint and is indexed by the
+ ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
+ unit, and the side of the unit."
+ INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide }
+ ::= { hdsl2ShdslEndpointMaintTable 1 }
+
+ Hdsl2ShdslEndpointMaintEntry ::=
+ SEQUENCE
+ {
+ hdsl2ShdslMaintLoopbackConfig INTEGER,
+ hdsl2ShdslMaintTipRingReversal INTEGER,
+ hdsl2ShdslMaintPowerBackOff INTEGER,
+ hdsl2ShdslMaintSoftRestart INTEGER
+ }
+
+ hdsl2ShdslMaintLoopbackConfig OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ noLoopback(1),
+ normalLoopback(2),
+ specialLoopback(3)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object controls configuration of loopbacks for the
+ associated segment endpoint. The status of the loopback
+ is obtained via the hdsl2ShdslEndpointCurrStatus object."
+ ::= { hdsl2ShdslEndpointMaintEntry 1 }
+
+ hdsl2ShdslMaintTipRingReversal OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ normal(1),
+ reversed(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+
+
+
+Sikes, et al. Standards Track [Page 41]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ "This object indicates the state of the tip/ring pair at the
+ associated segment endpoint."
+ ::= { hdsl2ShdslEndpointMaintEntry 2 }
+
+ hdsl2ShdslMaintPowerBackOff OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ default(1),
+ enhanced(2)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object configures the receiver at the associated
+ segment endpoint to operate in default or enhanced power
+ backoff mode."
+ ::= { hdsl2ShdslEndpointMaintEntry 3 }
+
+ hdsl2ShdslMaintSoftRestart OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ ready(1),
+ restart(2)
+ }
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object enables the manager to trigger a soft restart
+ of the modem at the associated segment endpoint. The
+ manager may only set this object to the 'restart(2)'
+ value, which initiates a restart. The agent will perform a
+ restart after approximately 5 seconds. Following the 5 second
+ period, the agent will restore the object to the 'ready(1)'
+ state."
+ ::= { hdsl2ShdslEndpointMaintEntry 4 }
+
+ hdsl2ShdslUnitMaintTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Hdsl2ShdslUnitMaintEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This table supports maintenance operations for units in a
+ HDSL2/SHDSL line. Entries in this table MUST be maintained
+ in a persistent manner."
+ ::= { hdsl2ShdslMibObjects 9 }
+
+ hdsl2ShdslUnitMaintEntry OBJECT-TYPE
+ SYNTAX Hdsl2ShdslUnitMaintEntry
+
+
+
+Sikes, et al. Standards Track [Page 42]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "An entry in the hdsl2ShdslUnitMaintTable. Each entry
+ corresponds to a single unit and is indexed by the
+ ifIndex of the HDSL2/SHDSL line and the UnitId of the
+ associated unit."
+ INDEX { ifIndex, hdsl2ShdslInvIndex }
+ ::= { hdsl2ShdslUnitMaintTable 1 }
+
+ Hdsl2ShdslUnitMaintEntry ::=
+ SEQUENCE
+ {
+ hdsl2ShdslMaintLoopbackTimeout Integer32,
+ hdsl2ShdslMaintUnitPowerSource INTEGER
+ }
+
+ hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE
+ SYNTAX Integer32(0..4095)
+ UNITS "minutes"
+ MAX-ACCESS read-write
+ STATUS current
+ DESCRIPTION
+ "This object configures the timeout value for loopbacks
+ initiated at segments endpoints contained in the associated
+ unit. A value of 0 disables the timeout."
+ ::= { hdsl2ShdslUnitMaintEntry 1 }
+
+ hdsl2ShdslMaintUnitPowerSource OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ local(1),
+ span(2)
+ }
+ MAX-ACCESS read-only
+ STATUS current
+ DESCRIPTION
+ "This object indicates the DC power source being used by the
+ associated unit."
+ ::= { hdsl2ShdslUnitMaintEntry 2 }
+
+ -- Span Configuration Profile Group
+ --
+
+ hdsl2ShdslSpanConfProfileTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfProfileEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+
+
+
+Sikes, et al. Standards Track [Page 43]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ DESCRIPTION
+ "This table supports definitions of span configuration
+ profiles for SHDSL lines. HDSL2 does not support these
+ configuration options. This table MUST be maintained
+ in a persistent manner."
+ ::= { hdsl2ShdslMibObjects 10 }
+
+ hdsl2ShdslSpanConfProfileEntry OBJECT-TYPE
+ SYNTAX Hdsl2ShdslSpanConfProfileEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry corresponds to a single span configuration
+ profile. Each profile contains a set of span configuration
+ parameters. The configuration parameters in a profile are
+ applied to those lines referencing that profile (see the
+ hdsl2ShdslSpanConfProfile object). Profiles may be
+ created/deleted using the row creation/deletion mechanism
+ via hdsl2ShdslSpanConfProfileRowStatus. If an active
+ entry is referenced in hdsl2ShdslSpanConfProfile, the
+ entry MUST remain active until all references are removed."
+ INDEX { IMPLIED hdsl2ShdslSpanConfProfileName }
+ ::= { hdsl2ShdslSpanConfProfileTable 1 }
+
+ Hdsl2ShdslSpanConfProfileEntry ::=
+ SEQUENCE
+ {
+ hdsl2ShdslSpanConfProfileName SnmpAdminString,
+ hdsl2ShdslSpanConfWireInterface INTEGER,
+ hdsl2ShdslSpanConfMinLineRate Unsigned32,
+ hdsl2ShdslSpanConfMaxLineRate Unsigned32,
+ hdsl2ShdslSpanConfPSD INTEGER,
+ hdsl2ShdslSpanConfTransmissionMode
+ Hdsl2ShdslTransmissionModeType,
+ hdsl2ShdslSpanConfRemoteEnabled INTEGER,
+ hdsl2ShdslSpanConfPowerFeeding INTEGER,
+ hdsl2ShdslSpanConfCurrCondTargetMarginDown Integer32,
+ hdsl2ShdslSpanConfWorstCaseTargetMarginDown Integer32,
+ hdsl2ShdslSpanConfCurrCondTargetMarginUp Integer32,
+ hdsl2ShdslSpanConfWorstCaseTargetMarginUp Integer32,
+ hdsl2ShdslSpanConfUsedTargetMargins BITS,
+ hdsl2ShdslSpanConfReferenceClock
+ Hdsl2ShdslClockReferenceType,
+ hdsl2ShdslSpanConfLineProbeEnable INTEGER,
+ hdsl2ShdslSpanConfProfileRowStatus RowStatus
+ }
+
+ hdsl2ShdslSpanConfProfileName OBJECT-TYPE
+
+
+
+Sikes, et al. Standards Track [Page 44]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ SYNTAX SnmpAdminString (SIZE(1..32))
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This object is the unique index associated with this profile.
+ Entries in this table are referenced via the object
+ hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry."
+ ::= { hdsl2ShdslSpanConfProfileEntry 1 }
+
+ hdsl2ShdslSpanConfWireInterface OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ twoWire(1),
+ fourWire(2),
+ sixWire(3),
+ eightWire(4)
+ }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object configures the two-wire or optional four-wire,
+ six-wire, or eight-wire operation for SHDSL lines."
+ DEFVAL { twoWire }
+ ::= { hdsl2ShdslSpanConfProfileEntry 2 }
+
+ hdsl2ShdslSpanConfMinLineRate OBJECT-TYPE
+ SYNTAX Unsigned32(0..4294967295)
+ UNITS "bps"
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object configures the minimum transmission rate for
+ the associated SHDSL Line in bits-per-second (bps) and includes
+ both payload (user data) and any applicable framing overhead.
+ If the minimum line rate equals the maximum line rate
+ (hdsl2ShdslSpanMaxLineRate), the line rate is considered
+ 'fixed'. If the minimum line rate is less than the
+ maximum line rate, the line rate is considered
+ 'rate-adaptive'."
+ DEFVAL { 1552000 }
+ ::= { hdsl2ShdslSpanConfProfileEntry 3 }
+
+ hdsl2ShdslSpanConfMaxLineRate OBJECT-TYPE
+ SYNTAX Unsigned32(0..4294967295)
+ UNITS "bps"
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+
+
+
+Sikes, et al. Standards Track [Page 45]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ "This object configures the maximum transmission rate for
+ the associated SHDSL Line in bits-per-second (bps) and includes
+ both payload (user data) and any applicable framing overhead.
+ If the minimum line rate equals the maximum line rate
+ (hdsl2ShdslSpanMaxLineRate), the line rate is considered
+ 'fixed'. If the minimum line rate is less than the
+ maximum line rate, the line rate is considered
+ 'rate-adaptive'."
+ DEFVAL { 1552000 }
+ ::= { hdsl2ShdslSpanConfProfileEntry 4 }
+
+ hdsl2ShdslSpanConfPSD OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ symmetric(1),
+ asymmetric(2)
+ }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object configures use of symmetric/asymmetric PSD (Power
+ Spectral Density) Mask for the associated SHDSL Line. Support
+ for symmetric PSD is mandatory for all supported data rates.
+ Support for asymmetric PSD is optional."
+ DEFVAL { symmetric }
+ ::= { hdsl2ShdslSpanConfProfileEntry 5 }
+
+ hdsl2ShdslSpanConfTransmissionMode OBJECT-TYPE
+ SYNTAX Hdsl2ShdslTransmissionModeType
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object specifies the regional setting for the SHDSL
+ line."
+ DEFVAL { { region1 } }
+ ::= { hdsl2ShdslSpanConfProfileEntry 6 }
+
+ hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ enabled(1),
+ disabled(2)
+ }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object enables/disables support for remote management
+ of the units in an SHDSL line from the STU-R via the EOC."
+
+
+
+Sikes, et al. Standards Track [Page 46]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ DEFVAL { enabled }
+ ::= { hdsl2ShdslSpanConfProfileEntry 7 }
+
+ hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ noPower(1),
+ powerFeed(2),
+ wettingCurrent(3)
+ }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object enables/disables support for optional power
+ feeding in an SHDSL line."
+ DEFVAL { noPower }
+ ::= { hdsl2ShdslSpanConfProfileEntry 8 }
+
+ hdsl2ShdslSpanConfCurrCondTargetMarginDown OBJECT-TYPE
+ SYNTAX Integer32(-10..21)
+ UNITS "dB"
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object specifies the downstream current condition target
+ SNR margin for an SHDSL line. The SNR margin is the difference
+ between the desired SNR and the actual SNR. Target SNR margin
+ is the desired SNR margin for a unit."
+ DEFVAL { 0 }
+ ::= { hdsl2ShdslSpanConfProfileEntry 9 }
+
+ hdsl2ShdslSpanConfWorstCaseTargetMarginDown OBJECT-TYPE
+ SYNTAX Integer32(-10..21)
+ UNITS "dB"
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object specifies the downstream worst-case target SNR
+ margin for an SHDSL line. The SNR margin is the difference
+ between the desired SNR and the actual SNR. Target SNR
+ margin is the desired SNR margin for a unit."
+ DEFVAL { 0 }
+ ::= { hdsl2ShdslSpanConfProfileEntry 10 }
+
+ hdsl2ShdslSpanConfCurrCondTargetMarginUp OBJECT-TYPE
+ SYNTAX Integer32(-10..21)
+ UNITS "dB"
+ MAX-ACCESS read-create
+
+
+
+Sikes, et al. Standards Track [Page 47]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ STATUS current
+ DESCRIPTION
+ "This object specifies the upstream current-condition target
+ SNR margin for an SHDSL line. The SNR margin is the difference
+ between the desired SNR and the actual SNR. Target SNR margin
+ is the desired SNR margin for a unit."
+ DEFVAL { 0 }
+ ::= { hdsl2ShdslSpanConfProfileEntry 11 }
+
+ hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPE
+ SYNTAX Integer32(-10..21)
+ UNITS "dB"
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object specifies the upstream worst-case target SNR
+ margin for an SHDSL line. The SNR margin is the difference
+ between the desired SNR and the actual SNR. Target SNR margin
+ is the desired SNR margin for a unit."
+ DEFVAL { 0 }
+ ::= { hdsl2ShdslSpanConfProfileEntry 12 }
+
+ hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE
+ SYNTAX BITS
+ {
+ currCondDown(0),
+ worstCaseDown(1),
+ currCondUp(2),
+ worstCaseUp(3)
+ }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "Indicates whether a target SNR margin is enabled or
+ disabled. This is a bit-map of possible settings. The
+ various bit positions are as follows:
+
+ currCondDown - current-condition downstream target SNR
+ margin enabled
+
+ worstCaseDown - worst-case downstream target SNR margin
+ enabled
+
+ currCondUp - current-condition upstream target SNR
+ margin enabled
+
+ worstCaseUp - worst-case upstream target SNR margin
+ enabled."
+
+
+
+Sikes, et al. Standards Track [Page 48]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ DEFVAL { { currCondDown } }
+ ::= { hdsl2ShdslSpanConfProfileEntry 13 }
+
+ hdsl2ShdslSpanConfReferenceClock OBJECT-TYPE
+ SYNTAX Hdsl2ShdslClockReferenceType
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object configures the clock reference for the STU-C
+ in an SHDSL Line."
+ DEFVAL { localClk }
+ ::= { hdsl2ShdslSpanConfProfileEntry 14 }
+
+ hdsl2ShdslSpanConfLineProbeEnable OBJECT-TYPE
+ SYNTAX INTEGER
+ {
+ disable(1),
+ enable(2)
+ }
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object enables/disables support for Line Probe of
+ the units in an SHDSL line. When Line Probe is enabled, the
+ system performs Line Probing to find the best possible
+ rate. If Line Probe is disabled, the rate adaptation phase
+ is skipped to shorten set up time."
+ DEFVAL { disable }
+ ::= { hdsl2ShdslSpanConfProfileEntry 15 }
+
+ hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE
+ SYNTAX RowStatus
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object controls creation/deletion of the associated
+ entry in this table per the semantics of RowStatus. If an
+ active entry is referenced in hdsl2ShdslSpanConfProfile, the
+ entry MUST remain active until all references are removed."
+ ::= { hdsl2ShdslSpanConfProfileEntry 16 }
+
+ -- Segment Endpoint Alarm Configuration Profile group
+ --
+
+ hdsl2ShdslEndpointAlarmConfProfileTable OBJECT-TYPE
+ SYNTAX SEQUENCE OF Hdsl2ShdslEndpointAlarmConfProfileEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+
+
+
+Sikes, et al. Standards Track [Page 49]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ DESCRIPTION
+ "This table supports definitions of alarm configuration
+ profiles for HDSL2/SHDSL segment endpoints. This table
+ MUST be maintained in a persistent manner."
+ ::= { hdsl2ShdslMibObjects 11 }
+
+ hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPE
+ SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "Each entry corresponds to a single alarm configuration profile.
+ Each profile contains a set of parameters for setting alarm
+ thresholds for various performance attributes monitored at
+ HDSL2/SHDSL segment endpoints. Profiles may be created/deleted
+ using the row creation/deletion mechanism via
+ hdsl2ShdslEndpointAlarmConfProfileRowStatus. If an active
+ entry is referenced in either hdsl2ShdslSpanConfAlarmProfile
+ or hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
+ active until all references are removed."
+ INDEX { IMPLIED hdsl2ShdslEndpointAlarmConfProfileName }
+ ::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 }
+
+ Hdsl2ShdslEndpointAlarmConfProfileEntry ::=
+ SEQUENCE
+ {
+ hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString,
+ hdsl2ShdslEndpointThreshLoopAttenuation Integer32,
+ hdsl2ShdslEndpointThreshSNRMargin Integer32,
+ hdsl2ShdslEndpointThreshES
+ Hdsl2ShdslPerfIntervalThreshold,
+ hdsl2ShdslEndpointThreshSES
+ Hdsl2ShdslPerfIntervalThreshold,
+ hdsl2ShdslEndpointThreshCRCanomalies Integer32,
+ hdsl2ShdslEndpointThreshLOSWS
+ Hdsl2ShdslPerfIntervalThreshold,
+ hdsl2ShdslEndpointThreshUAS
+ Hdsl2ShdslPerfIntervalThreshold,
+ hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus
+ }
+
+ hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE
+ SYNTAX SnmpAdminString (SIZE(1..32))
+ MAX-ACCESS not-accessible
+ STATUS current
+ DESCRIPTION
+ "This object is the unique index associated with this profile."
+ ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 1 }
+
+
+
+Sikes, et al. Standards Track [Page 50]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPE
+ SYNTAX Integer32(-127..128)
+ UNITS "dB"
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object configures the loop attenuation alarm threshold.
+ When the current value of hdsl2ShdslEndpointCurrAtn reaches
+ or exceeds this threshold, an hdsl2ShdslLoopAttenCrossing
+ MAY be generated."
+ DEFVAL { 0 }
+ ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 2 }
+
+ hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPE
+ SYNTAX Integer32(-127..128)
+ UNITS "dB"
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object configures the SNR margin alarm threshold.
+ When the current value of hdsl2ShdslEndpointCurrSnrMgn
+ reaches or drops below this threshold, a
+ hdsl2ShdslSNRMarginCrossing MAY be generated."
+ DEFVAL { 0 }
+ ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 3 }
+
+ hdsl2ShdslEndpointThreshES OBJECT-TYPE
+ SYNTAX Hdsl2ShdslPerfIntervalThreshold
+ UNITS "seconds"
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object configures the threshold for the number of
+ Errored Seconds (ES) within any given 15-minute performance
+ data collection interval. If the value of Errored Seconds
+ in a particular 15-minute collection interval reaches/
+ exceeds this value, an hdsl2ShdslPerfESThresh MAY be
+ generated. At most, one notification will be sent per
+ interval per endpoint."
+ DEFVAL { 0 }
+ ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 4 }
+
+ hdsl2ShdslEndpointThreshSES OBJECT-TYPE
+ SYNTAX Hdsl2ShdslPerfIntervalThreshold
+ UNITS "seconds"
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+
+
+
+Sikes, et al. Standards Track [Page 51]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ "This object configures the threshold for the number of
+ Severely Errored Seconds (SES) within any given 15-minute
+ performance data collection interval. If the value of
+ Severely Errored Seconds in a particular 15-minute collection
+ interval reaches/exceeds this value, an hdsl2ShdslPerfSESThresh
+ MAY be generated. At most, one notification will be sent per
+ interval per endpoint."
+ DEFVAL { 0 }
+ ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 5 }
+
+ hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPE
+ SYNTAX Integer32
+ UNITS "detected CRC Anomalies"
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object configures the threshold for the number of
+ CRC anomalies within any given 15-minute performance data
+ collection interval. If the value of CRC anomalies in a
+ particular 15-minute collection interval reaches/exceeds
+ this value, an hdsl2ShdslPerfCRCanomaliesThresh MAY be
+ generated. At most, one notification will be sent per
+ interval per endpoint."
+ DEFVAL { 0 }
+ ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 6 }
+
+ hdsl2ShdslEndpointThreshLOSWS OBJECT-TYPE
+ SYNTAX Hdsl2ShdslPerfIntervalThreshold
+ UNITS "seconds"
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object configures the threshold for the number of
+ Loss of Sync Word (LOSW) Seconds within any given 15-minute
+ performance data collection interval. If the value of LOSW
+ in a particular 15-minute collection interval reaches/exceeds
+ this value, an hdsl2ShdslPerfLOSWSThresh MAY be generated.
+ At most, one notification will be sent per interval per
+ endpoint."
+ DEFVAL { 0 }
+ ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 7 }
+
+ hdsl2ShdslEndpointThreshUAS OBJECT-TYPE
+ SYNTAX Hdsl2ShdslPerfIntervalThreshold
+ UNITS "seconds"
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+
+
+
+Sikes, et al. Standards Track [Page 52]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ "This object configures the threshold for the number of
+ Unavailable Seconds (UAS) within any given 15-minute
+ performance data collection interval. If the value of UAS
+ in a particular 15-minute collection interval reaches/exceeds
+ this value, an hdsl2ShdslPerfUASThresh MAY be generated.
+ At most, one notification will be sent per interval per
+ endpoint."
+ DEFVAL { 0 }
+ ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 8 }
+
+ hdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPE
+ SYNTAX RowStatus
+ MAX-ACCESS read-create
+ STATUS current
+ DESCRIPTION
+ "This object controls creation/deletion of the associated
+ entry in this table as per the semantics of RowStatus.
+ If an active entry is referenced in either
+ hdsl2ShdslSpanConfAlarmProfile or
+ hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
+ active until all references are removed."
+ ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 9 }
+
+ -- Notifications Group
+ --
+
+ hdsl2ShdslNotifications OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 0 }
+
+ hdsl2ShdslLoopAttenCrossing NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurrAtn,
+ hdsl2ShdslEndpointThreshLoopAttenuation
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that the loop attenuation
+ threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation
+ value) has been reached/exceeded for the HDSL2/SHDSL segment
+ endpoint."
+ ::= { hdsl2ShdslNotifications 1 }
+
+ hdsl2ShdslSNRMarginCrossing NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurrSnrMgn,
+ hdsl2ShdslEndpointThreshSNRMargin
+ }
+
+
+
+Sikes, et al. Standards Track [Page 53]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that the SNR margin threshold (as
+ per the hdsl2ShdslEndpointThreshSNRMargin value) has been
+ reached/exceeded for the HDSL2/SHDSL segment endpoint."
+ ::= { hdsl2ShdslNotifications 2 }
+
+ hdsl2ShdslPerfESThresh NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurr15MinES,
+ hdsl2ShdslEndpointThreshES
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that the errored seconds
+ threshold (as per the hdsl2ShdslEndpointThreshES value)
+ has been reached/exceeded for the HDSL2/SHDSL segment
+ endpoint."
+ ::= { hdsl2ShdslNotifications 3 }
+
+ hdsl2ShdslPerfSESThresh NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurr15MinSES,
+ hdsl2ShdslEndpointThreshSES
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that the severely errored seconds
+ threshold (as per the hdsl2ShdslEndpointThreshSES value) has
+ been reached/exceeded for the HDSL2/SHDSL segment endpoint."
+ ::= { hdsl2ShdslNotifications 4 }
+
+ hdsl2ShdslPerfCRCanomaliesThresh NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurr15MinCRCanomalies,
+ hdsl2ShdslEndpointThreshCRCanomalies
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that the CRC anomalies threshold
+ (as per the hdsl2ShdslEndpointThreshCRCanomalies value) has
+ been reached/exceeded for the HDSL2/SHDSL segment endpoint."
+ ::= { hdsl2ShdslNotifications 5 }
+
+ hdsl2ShdslPerfLOSWSThresh NOTIFICATION-TYPE
+
+
+
+Sikes, et al. Standards Track [Page 54]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurr15MinLOSWS,
+ hdsl2ShdslEndpointThreshLOSWS
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that the LOSW Seconds threshold
+ (as per the hdsl2ShdslEndpointThreshLOSWS value) has been
+ reached/exceeded for the HDSL2/SHDSL segment endpoint."
+ ::= { hdsl2ShdslNotifications 6 }
+
+ hdsl2ShdslPerfUASThresh NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurr15MinUAS,
+ hdsl2ShdslEndpointThreshUAS
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that the unavailable seconds
+ threshold (as per the hdsl2ShdslEndpointThreshUAS value) has
+ been reached/exceeded for the HDSL2/SHDSL segment endpoint."
+ ::= { hdsl2ShdslNotifications 7 }
+
+ hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslSpanConfNumRepeaters
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that a mismatch has been detected
+ between the number of repeater/regenerator units configured
+ for an HDSL2/SHDSL line via the hdsl2ShdslSpanConfNumRepeaters
+ object and the actual number of repeater/regenerator units
+ discovered via the EOC."
+ ::= { hdsl2ShdslNotifications 8 }
+
+ hdsl2ShdslLoopbackFailure NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslMaintLoopbackConfig
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that an endpoint maintenance
+ loopback command failed for an HDSL2/SHDSL segment."
+
+
+
+Sikes, et al. Standards Track [Page 55]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ ::= { hdsl2ShdslNotifications 9 }
+
+ hdsl2ShdslpowerBackoff NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurrStatus
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that the bit setting for
+ powerBackoff in the hdsl2ShdslEndpointCurrStatus object for
+ this endpoint has changed."
+ ::= { hdsl2ShdslNotifications 10 }
+
+ hdsl2ShdsldeviceFault NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurrStatus
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that the bit setting for
+ deviceFault in the hdsl2ShdslEndpointCurrStatus object for
+ this endpoint has changed."
+ ::= { hdsl2ShdslNotifications 11 }
+
+ hdsl2ShdsldcContinuityFault NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurrStatus
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that the bit setting for
+ dcContinuityFault in the hdsl2ShdslEndpointCurrStatus object
+ for this endpoint has changed."
+ ::= { hdsl2ShdslNotifications 12 }
+
+ hdsl2ShdslconfigInitFailure NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurrStatus
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that the bit setting for
+ configInitFailure in the hdsl2ShdslEndpointCurrStatus object
+ for this endpoint has changed."
+
+
+
+Sikes, et al. Standards Track [Page 56]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ ::= { hdsl2ShdslNotifications 13 }
+
+ hdsl2ShdslprotocolInitFailure NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurrStatus
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that the bit setting for
+ protocolInitFailure in the hdsl2ShdslEndpointCurrStatus
+ object for this endpoint has changed."
+ ::= { hdsl2ShdslNotifications 14 }
+
+ hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurrStatus
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates that the bit setting for
+ noNeighborPresent in the hdsl2ShdslEndpointCurrStatus object
+ for this endpoint has changed."
+ ::= { hdsl2ShdslNotifications 15 }
+
+ hdsl2ShdslLocalPowerLoss NOTIFICATION-TYPE
+ OBJECTS
+ {
+ hdsl2ShdslInvVendorID
+ }
+ STATUS current
+ DESCRIPTION
+ "This notification indicates impending unit failure due to
+ loss of local power (last gasp)."
+ ::= { hdsl2ShdslNotifications 16 }
+
+ -- conformance information
+ --
+
+ hdsl2ShdslConformance OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 3 }
+ hdsl2ShdslGroups OBJECT IDENTIFIER ::=
+ { hdsl2ShdslConformance 1 }
+ hdsl2ShdslCompliances OBJECT IDENTIFIER ::=
+ { hdsl2ShdslConformance 2 }
+
+ -- agent compliance statements
+
+
+
+
+Sikes, et al. Standards Track [Page 57]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ hdsl2ShdslLineMibCompliance MODULE-COMPLIANCE
+ STATUS deprecated
+ DESCRIPTION
+ "The compliance statement for SNMP entities that implement
+ HDSL2 and SHDSL. The version of SHDSL supported in this
+ compliance statement is g.shdsl.
+
+ **** This compliance statement is deprecated. ****"
+ MODULE
+ MANDATORY-GROUPS
+ {
+ hdsl2ShdslSpanConfGroup,
+ hdsl2ShdslSpanStatusGroup,
+ hdsl2ShdslInventoryGroup,
+ hdsl2ShdslEndpointConfGroup,
+ hdsl2ShdslEndpointCurrGroup,
+ hdsl2Shdsl15MinIntervalGroup,
+ hdsl2Shdsl1DayIntervalGroup,
+ hdsl2ShdslMaintenanceGroup,
+ hdsl2ShdslEndpointAlarmConfGroup,
+ hdsl2ShdslNotificationGroup
+ }
+
+ GROUP hdsl2ShdslInventoryShdslGroup
+ DESCRIPTION
+ "Support for this group is only required for implementations
+ supporting SHDSL lines."
+
+ GROUP hdsl2ShdslSpanShdslStatusGroup
+ DESCRIPTION
+ "Support for this group is only required for implementations
+ supporting SHDSL lines."
+
+ GROUP hdsl2ShdslSpanConfProfileGroup
+ DESCRIPTION
+ "Support for this group is only required for implementations
+ supporting SHDSL lines."
+
+ OBJECT hdsl2ShdslSpanConfWireInterface
+ SYNTAX INTEGER
+ {
+ twoWire(1),
+ fourWire(2)
+ }
+ DESCRIPTION
+ "An implementation only has to support the range as
+ applicable for the original g.shdsl specification defined
+ in RFC 3276."
+
+
+
+Sikes, et al. Standards Track [Page 58]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ OBJECT hdsl2ShdslStatusMaxAttainableLineRate
+ SYNTAX Unsigned32(0..4112000)
+ DESCRIPTION
+ "An implementation only has to support the range as
+ applicable for the original g.shdsl specification defined
+ in RFC 3276."
+
+ OBJECT hdsl2ShdslStatusActualLineRate
+ SYNTAX Unsigned32(0..4112000)
+ DESCRIPTION
+ "An implementation only has to support the range as
+ applicable for the original g.shdsl specification defined
+ in RFC 3276."
+
+ OBJECT hdsl2ShdslSpanConfMinLineRate
+ SYNTAX Unsigned32(0..4112000)
+ DESCRIPTION
+ "An implementation only has to support the range as
+ applicable for the original g.shdsl specification defined
+ in RFC 3276."
+
+ OBJECT hdsl2ShdslSpanConfMaxLineRate
+ SYNTAX Unsigned32(0..4112000)
+ DESCRIPTION
+ "An implementation only has to support the range as
+ applicable for the original g.shdsl specification defined
+ in RFC 3276."
+
+ ::= { hdsl2ShdslCompliances 1 }
+
+ hdsl2GshdslbisLineMibCompliance MODULE-COMPLIANCE
+ STATUS current
+ DESCRIPTION
+ "The compliance statement for SNMP entities that implement
+ HDSL2 and SHDSL. The version of SHDSL supported in this
+ compliance statement is g.shdsl.bis."
+ MODULE
+ MANDATORY-GROUPS
+ {
+ hdsl2ShdslSpanConfGroup,
+ hdsl2ShdslSpanStatusGroup,
+ hdsl2ShdslInventoryGroup,
+ hdsl2ShdslEndpointConfGroup,
+ hdsl2ShdslEndpointCurrGroup,
+ hdsl2Shdsl15MinIntervalGroup,
+ hdsl2Shdsl1DayIntervalGroup,
+ hdsl2ShdslMaintenanceGroup,
+ hdsl2ShdslEndpointAlarmConfGroup,
+
+
+
+Sikes, et al. Standards Track [Page 59]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ hdsl2ShdslNotificationGroup
+ }
+
+ GROUP hdsl2ShdslInventoryShdslGroup
+ DESCRIPTION
+ "Support for this group is only required for implementations
+ supporting SHDSL lines."
+
+ GROUP hdsl2ShdslSpanShdslStatusGroup
+ DESCRIPTION
+ "Support for this group is only required for implementations
+ supporting SHDSL lines."
+
+ GROUP hdsl2ShdslSpanConfProfileGroup
+ DESCRIPTION
+ "Support for this group is only required for implementations
+ supporting SHDSL lines."
+
+ GROUP hdsl2ShdslWirePairGroup
+ DESCRIPTION
+ "Support for this group is only required for implementations
+ supporting SHDSL lines."
+
+ GROUP hdsl2ShdslPayloadRateGroup
+ DESCRIPTION
+ "Support for this group is only required for implementations
+ supporting SHDSL lines."
+
+ ::= { hdsl2ShdslCompliances 2 }
+
+ -- units of conformance
+ --
+
+ hdsl2ShdslSpanConfGroup OBJECT-GROUP
+ OBJECTS
+ {
+ hdsl2ShdslSpanConfNumRepeaters,
+ hdsl2ShdslSpanConfProfile,
+ hdsl2ShdslSpanConfAlarmProfile
+ }
+ STATUS current
+ DESCRIPTION
+ "This group supports objects for configuring span-related
+ parameters for HDSL2/SHDSL lines."
+ ::= { hdsl2ShdslGroups 1 }
+
+ hdsl2ShdslSpanStatusGroup OBJECT-GROUP
+ OBJECTS
+
+
+
+Sikes, et al. Standards Track [Page 60]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ {
+ hdsl2ShdslStatusNumAvailRepeaters
+ }
+ STATUS current
+ DESCRIPTION
+ "This group supports objects for retrieving span-related
+ status for HDSL2/SHDSL lines."
+ ::= { hdsl2ShdslGroups 2 }
+
+ hdsl2ShdslInventoryShdslGroup OBJECT-GROUP
+ OBJECTS
+ {
+ hdsl2ShdslInvTransmissionModeCapability
+ }
+ STATUS current
+ DESCRIPTION
+ "This group supports objects for retrieving SHDSL-specific
+ inventory information."
+ ::= { hdsl2ShdslGroups 3 }
+
+ hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP
+ OBJECTS
+ {
+ hdsl2ShdslStatusMaxAttainableLineRate,
+ hdsl2ShdslStatusActualLineRate,
+ hdsl2ShdslStatusTransmissionModeCurrent
+ }
+ STATUS current
+ DESCRIPTION
+ "This group supports objects for retrieving SHDSL-specific
+ span-related status."
+ ::= { hdsl2ShdslGroups 4 }
+
+ hdsl2ShdslInventoryGroup OBJECT-GROUP
+ OBJECTS
+ {
+ hdsl2ShdslInvVendorID,
+ hdsl2ShdslInvVendorModelNumber,
+ hdsl2ShdslInvVendorSerialNumber,
+ hdsl2ShdslInvVendorEOCSoftwareVersion,
+ hdsl2ShdslInvStandardVersion,
+ hdsl2ShdslInvVendorListNumber,
+ hdsl2ShdslInvVendorIssueNumber,
+ hdsl2ShdslInvVendorSoftwareVersion,
+ hdsl2ShdslInvEquipmentCode,
+ hdsl2ShdslInvVendorOther
+ }
+ STATUS current
+
+
+
+Sikes, et al. Standards Track [Page 61]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ DESCRIPTION
+ "This group supports objects that provide unit inventory
+ information about the units in HDSL2/SHDSL lines."
+ ::= { hdsl2ShdslGroups 5 }
+
+ hdsl2ShdslEndpointConfGroup OBJECT-GROUP
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurrAtn
+ }
+ STATUS current
+ DESCRIPTION
+ "This group supports objects for configuring parameters for
+ segment endpoints in HDSL2/SHDSL lines."
+ ::= { hdsl2ShdslGroups 6 }
+
+ hdsl2ShdslEndpointCurrGroup OBJECT-GROUP
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurrAtn,
+ hdsl2ShdslEndpointCurrSnrMgn,
+ hdsl2ShdslEndpointCurrStatus,
+ hdsl2ShdslEndpointES,
+ hdsl2ShdslEndpointSES,
+ hdsl2ShdslEndpointCRCanomalies,
+ hdsl2ShdslEndpointLOSWS,
+ hdsl2ShdslEndpointUAS,
+ hdsl2ShdslEndpointCurr15MinTimeElapsed,
+ hdsl2ShdslEndpointCurr15MinES,
+ hdsl2ShdslEndpointCurr15MinSES,
+ hdsl2ShdslEndpointCurr15MinCRCanomalies,
+ hdsl2ShdslEndpointCurr15MinLOSWS,
+ hdsl2ShdslEndpointCurr15MinUAS,
+ hdsl2ShdslEndpointCurr1DayTimeElapsed,
+ hdsl2ShdslEndpointCurr1DayES,
+ hdsl2ShdslEndpointCurr1DaySES,
+ hdsl2ShdslEndpointCurr1DayCRCanomalies,
+ hdsl2ShdslEndpointCurr1DayLOSWS,
+ hdsl2ShdslEndpointCurr1DayUAS
+ }
+ STATUS current
+ DESCRIPTION
+ "This group supports objects that provide current status and
+ performance measurements relating to segment endpoints in
+ HDSL2/SHDSL lines."
+ ::= { hdsl2ShdslGroups 7 }
+
+ hdsl2Shdsl15MinIntervalGroup OBJECT-GROUP
+
+
+
+Sikes, et al. Standards Track [Page 62]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ OBJECTS
+ {
+ hdsl2Shdsl15MinIntervalES,
+ hdsl2Shdsl15MinIntervalSES,
+ hdsl2Shdsl15MinIntervalCRCanomalies,
+ hdsl2Shdsl15MinIntervalLOSWS,
+ hdsl2Shdsl15MinIntervalUAS
+ }
+ STATUS current
+ DESCRIPTION
+ "This group supports objects that maintain historic
+ performance measurements relating to segment endpoints in
+ HDSL2/SHDSL lines in 15-minute intervals."
+ ::= { hdsl2ShdslGroups 8 }
+
+ hdsl2Shdsl1DayIntervalGroup OBJECT-GROUP
+ OBJECTS
+ {
+ hdsl2Shdsl1DayIntervalMoniSecs,
+ hdsl2Shdsl1DayIntervalES,
+ hdsl2Shdsl1DayIntervalSES,
+ hdsl2Shdsl1DayIntervalCRCanomalies,
+ hdsl2Shdsl1DayIntervalLOSWS,
+ hdsl2Shdsl1DayIntervalUAS
+ }
+ STATUS current
+ DESCRIPTION
+ "This group supports objects that maintain historic
+ performance measurements relating to segment endpoints in
+ HDSL2/SHDSL lines in 1-day intervals."
+ ::= { hdsl2ShdslGroups 9 }
+
+ hdsl2ShdslMaintenanceGroup OBJECT-GROUP
+ OBJECTS
+ {
+ hdsl2ShdslMaintLoopbackConfig,
+ hdsl2ShdslMaintTipRingReversal,
+ hdsl2ShdslMaintPowerBackOff,
+ hdsl2ShdslMaintSoftRestart,
+ hdsl2ShdslMaintLoopbackTimeout,
+ hdsl2ShdslMaintUnitPowerSource
+ }
+ STATUS current
+ DESCRIPTION
+ "This group supports objects that provide support for
+ maintenance actions for HDSL2/SHDSL lines."
+ ::= { hdsl2ShdslGroups 10 }
+
+
+
+
+Sikes, et al. Standards Track [Page 63]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ hdsl2ShdslEndpointAlarmConfGroup OBJECT-GROUP
+ OBJECTS
+ {
+ hdsl2ShdslEndpointAlarmConfProfile,
+ hdsl2ShdslEndpointThreshLoopAttenuation,
+ hdsl2ShdslEndpointThreshSNRMargin,
+ hdsl2ShdslEndpointThreshES,
+ hdsl2ShdslEndpointThreshSES,
+ hdsl2ShdslEndpointThreshCRCanomalies,
+ hdsl2ShdslEndpointThreshLOSWS,
+ hdsl2ShdslEndpointThreshUAS,
+ hdsl2ShdslEndpointAlarmConfProfileRowStatus
+ }
+ STATUS current
+ DESCRIPTION
+ "This group supports objects that allow configuration of alarm
+ thresholds for various performance parameters for HDSL2/SHDSL
+ lines."
+ ::= { hdsl2ShdslGroups 11 }
+
+ hdsl2ShdslNotificationGroup NOTIFICATION-GROUP
+ NOTIFICATIONS
+ {
+ hdsl2ShdslLoopAttenCrossing,
+ hdsl2ShdslSNRMarginCrossing,
+ hdsl2ShdslPerfESThresh,
+ hdsl2ShdslPerfSESThresh,
+ hdsl2ShdslPerfCRCanomaliesThresh,
+ hdsl2ShdslPerfLOSWSThresh,
+ hdsl2ShdslPerfUASThresh,
+ hdsl2ShdslSpanInvalidNumRepeaters,
+ hdsl2ShdslLoopbackFailure,
+ hdsl2ShdslpowerBackoff,
+ hdsl2ShdsldeviceFault,
+ hdsl2ShdsldcContinuityFault,
+ hdsl2ShdslconfigInitFailure,
+ hdsl2ShdslprotocolInitFailure,
+ hdsl2ShdslnoNeighborPresent,
+ hdsl2ShdslLocalPowerLoss
+ }
+ STATUS current
+ DESCRIPTION
+ "This group supports notifications of significant conditions
+ associated with HDSL2/SHDSL lines."
+ ::= { hdsl2ShdslGroups 12 }
+
+ hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP
+ OBJECTS
+
+
+
+Sikes, et al. Standards Track [Page 64]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ {
+ hdsl2ShdslSpanConfWireInterface,
+ hdsl2ShdslSpanConfMinLineRate,
+ hdsl2ShdslSpanConfMaxLineRate,
+ hdsl2ShdslSpanConfPSD,
+ hdsl2ShdslSpanConfTransmissionMode,
+ hdsl2ShdslSpanConfRemoteEnabled,
+ hdsl2ShdslSpanConfPowerFeeding,
+ hdsl2ShdslSpanConfCurrCondTargetMarginDown,
+ hdsl2ShdslSpanConfWorstCaseTargetMarginDown,
+ hdsl2ShdslSpanConfCurrCondTargetMarginUp,
+ hdsl2ShdslSpanConfWorstCaseTargetMarginUp,
+ hdsl2ShdslSpanConfUsedTargetMargins,
+ hdsl2ShdslSpanConfReferenceClock,
+ hdsl2ShdslSpanConfLineProbeEnable,
+ hdsl2ShdslSpanConfProfileRowStatus
+ }
+ STATUS current
+ DESCRIPTION
+ "This group supports objects that constitute configuration
+ profiles for configuring span-related parameters in SHDSL
+ lines."
+ ::= { hdsl2ShdslGroups 13 }
+
+ hdsl2ShdslWirePairGroup OBJECT-GROUP
+ OBJECTS
+ {
+ hdsl2ShdslEndpointCurrTipRingReversal,
+ hdsl2ShdslEndpointCurrActivationState
+ }
+ STATUS current
+ DESCRIPTION
+ "This group supports objects that provide the status
+ of SHDSL-specific wire pairs."
+ ::= { hdsl2ShdslGroups 14 }
+
+ hdsl2ShdslPayloadRateGroup OBJECT-GROUP
+ OBJECTS
+ {
+ hdsl2ShdslStatusMaxAttainablePayloadRate,
+ hdsl2ShdslStatusActualPayloadRate
+ }
+ STATUS current
+ DESCRIPTION
+ "This group supports objects for retrieving payload rates
+ that exclude any framing overhead."
+ ::= { hdsl2ShdslGroups 15 }
+
+
+
+
+Sikes, et al. Standards Track [Page 65]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ END
+
+4. Implementation Analysis
+
+ A management application that supports RFC 3276 could mistakenly flag
+ a unit that responds with a rate or wire pair that exceeds the ranges
+ and/or enumerations specified in RFC 3276. For example, a
+ G.shdsl.bis line with four wire pairs would report statistics for
+ wire pairs that do not exist in RFC 3276. That is, a GET-NEXT
+ request issues with the object identifier:
+
+ hdsl2ShdslEndpointCurrAtn.1.1.1.2
+
+ might return
+
+ hdsl2ShdslEndpointCurrAtn.1.1.1.3 = 0
+
+ with a G.shdsl.bis unit and
+
+ hdsl2ShdslEndpointCurrSnrMgn.1.1.1.1 = 0
+
+ with an HDSL2 unit as these objects are indexed by
+
+ INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslendpointSide,
+ hdsl2ShdslEndpointWirePair }
+
+ A management application intended to manage G.shdsl.bis agents SHOULD
+ be modified to accept this sequence.
+
+ One should note that this same unmodified management application is
+ still capable of managing G.shdsl.bis agents albeit to the degree of
+ G.SHDSL (non-bis) limitations. That is, it can create and monitor
+ configurations limited to two wire pairs with an upper-rate limit of
+ 4112000 bits/second.
+
+5. Security Considerations
+
+ There are a number of management objects defined in this MIB module
+ with a MAX-ACCESS clause of read-write and/or read-create. Such
+ objects may be considered sensitive or vulnerable in some network
+ environments. The support for SET operations in a non-secure
+ environment without proper protection can have a negative effect on
+ network operations. These are the tables and objects and their
+ sensitivity/vulnerability:
+
+
+
+
+
+
+
+Sikes, et al. Standards Track [Page 66]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ o hdsl2ShdslSpanConfTable
+
+ The table consists of the following objects that support SET
+ operations:
+
+ * hdsl2ShdslSpanConfNumRepeaters
+ * hdsl2ShdslSpanConfProfile
+ * hdsl2ShdslSpanConfAlarmProfile
+
+ Unauthorized changes to hdsl2ShdslSpanConfNumRepeaters could
+ result in an hdsl2ShdslSpanInvalidNumRepeaters notification. Note
+ the discussion on hdsl2ShdslSpanInvalidNumRepeaters in the
+ Notifications section above.
+
+ Unauthorized changes to hdsl2ShdslSpanConfProfile could have an
+ adverse operational effect on a span. Reference the
+ hdsl2ShdslSpanConfProfileTable discussion below.
+
+ Unauthorized changes to hdsl2ShdslSpanConfAlarmProfile could have
+ a contrary effect on notifications. Reference the
+ hdsl2ShdslEndpointAlarmConfProfileTable discussion below.
+
+ o hdsl2ShdslEndpointConfTable
+
+ This table contains one object,
+ hdsl2ShdslEndpointAlarmConfProfile, that supports SET operations.
+ Unauthorized changes could have an undesirable notifications.
+ Reference the hdsl2ShdslEndpointAlarmConfProfileTable discussion
+ below.
+
+ o hdsl2ShdslEndpointMaintTable
+
+ The table consists of the following objects that support SET
+ operations:
+
+ * hdsl2ShdslMaintLoopbackConfig
+ * hdsl2ShdslMaintPowerBackoff
+ * hdsl2ShdslMaintSoftRestart
+
+ Unauthorized changes to hdsl2ShdslMaintLoopbackConfig could
+ prevent end-to-end data transfer due to an activation of a
+ loopback.
+
+ Unauthorized changes to hdsl2ShdslMaintPowerBackoff could result
+ in an increased in bundle interference.
+
+
+
+
+
+
+Sikes, et al. Standards Track [Page 67]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ Unauthorized changes to hdsl2ShdslMaintSoftRestart could result in
+ a temporary interruption of end-to-end data transfer as the result
+ of the triggering of a soft restart.
+
+ o hdsl2ShdslUnitMaintTable
+
+ This table contains one object, hdsl2ShdslMaintLoopbackTimeout,
+ that supports SET operations. An unauthorized change to this
+ object could result in the timeout value for loopbacks being
+ increased, decreased, or disabled.
+
+ o hdsl2ShdslSpanConfProfileTable
+
+ The table consists of the following objects that support SET
+ operations:
+
+ * hdsl2ShdslSpanConfWireInterface
+ * hdsl2ShdslSpanConfMinLineRate
+ * hdsl2ShdslSpanConfMaxLineRate
+ * hdsl2ShdslSpanConfPSD
+ * hdsl2ShdslSpanConfTransmissionMode
+ * hdsl2ShdslSpanConfRemoteEnabled
+ * hdsl2ShdslSpanConfPowerFeeding
+ * hdsl2ShdslSpanConfCurrCondTargetMarginDown
+ * hdsl2ShdslSpanConfWorstCaseTargetMarginDown
+ * hdsl2ShdslSpanConfCurrCondTargetMarginUp
+ * hdsl2ShdslSpanConfWorstCaseTargetMarginUp
+ * hdsl2ShdslSpanConfUsedTargetMargins
+ * hdsl2ShdslSpanConfReferenceClock
+ * hdsl2ShdslSpanConfLineProbeEnable
+ * hdsl2ShdslSpanConfProfileRowStatus
+
+ Setting any of the objects to an incorrect value could have an
+ adverse operational effect on a span.
+
+ Unauthorized changes to the hdsl2ShdslSpanConfWireInterface could
+ result in the failure of a span to achieve activation to a state
+ that would permit data flow. For example, setting this object to
+ six-wire or eight-wire operation when one of the units in the span
+ only supports two-wire or four-wire operation would likely prevent
+ an expected end-to-end data transfer capability.
+
+ Unauthorized changes to hdsl2ShdslSpanConfMinLineRate or
+ hdsl2ShdslSpanConfMaxLineRate could have an adverse effect on
+ performance. The range of allowable line rates could be altered
+ such that the span may not be able to train to a line rate that
+
+
+
+
+
+Sikes, et al. Standards Track [Page 68]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ would permit any end-user data to traverse the span or the span
+ could train to a line rate that is either greater than or less
+ than the line rate that the provider has pledged.
+
+ Unauthorized changes to hdsl2ShdslSpanConfPSD or
+ hdsl2ShdslSpanConfTransmissionMode could have a detrimental effect
+ on loop reach, performance, or spectral compatibility.
+
+ Unauthorized changes to hdsl2ShdslSpanConfRemoteEnable could alter
+ the remote management ability of units.
+
+ Unauthorized changes to hdsl2ShdslSpanConfPowerFeeding could
+ shutdown units that are expected to be fed power remotely.
+ Changing the configuration such that wetting current is not
+ supplied may result in corrosion of electrical contacts.
+
+ Unauthorized changes to
+ hdsl2ShdslSpanConfCurrCondTargetMarginDown,
+ hdsl2ShdslSpanConfWorstCaseTargetMarginDown,
+ hdsl2ShdslSpanConfCurrCondTargetMarginUp,
+ hdsl2ShdslSpanConfWorstCaseTargetMarginUp, or
+ hdsl2ShdslSpanConfUsedTargetMargins could result in invalid
+ parameters used to determine if a data rate can be supported under
+ current and worst-case noise.
+
+ Unauthorized changes to hdsl2ShdslSpanConfReferenceClock could
+ result in the selection of a clock source that might either
+ prevent any data from being transferred or impair data transfer.
+ In addition, an increase in CRC anomalies may be experienced.
+
+ Unauthorized changes to hdsl2ShdslSpanConfLineProbeEnable could
+ have a negative effect on selecting the optimum rate or power
+ level based on current line conditions.
+
+ Unauthorized changes to row status could result in unwanted
+ profiles being created or brought into service. Also, changes to
+ the row status could result in profiles being inadvertently
+ deleted or taken out of service.
+
+ o hdsl2ShdslEndpointAlarmConfProfileTable
+
+ The table consists of the following objects that support SET
+ operations:
+
+ * hdsl2ShdslEndpointThreshLoopAttenuation
+ * hdsl2ShdslEndpointThreshSNRMargin
+ * hdsl2ShdslEndpointThreshES
+ * hdsl2ShdslEndpointThreshSES
+
+
+
+Sikes, et al. Standards Track [Page 69]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ * hdsl2ShdslEndpointThreshCRCanomalies
+ * hdsl2ShdslEndpointThreshLOSWS
+ * hdsl2ShdslEndpointThreshUAS
+ * hdsl2ShdslEndpointAlarmConfProfileRowStatus
+
+ Increasing any of the threshold values could result in a
+ notification being suppressed or deferred. Setting a threshold to
+ 0 could result in a notification being suppressed. Suppressing or
+ deferring a notification could prevent the timely delivery of
+ important diagnostic information. Decreasing any of the threshold
+ values could result in a notification being sent from the network
+ falsely reporting a threshold crossing.
+
+ Changing a threshold value could also have an impact on the amount
+ of notifications the agent sends. This document adds a paragraph,
+ which was not in RFC 3276 [RFC3276], to the Notifications section
+ that provides general guidance to the rate limiting of
+ notifications. Agent implementations not adhering to the rate-
+ limiting desires could result in notifications being generated at
+ an uncontrolled rate. Unauthorized changes to a threshold value
+ could result in an undesired notification rate.
+
+ Unauthorized changes to row status could result in unwanted
+ profiles being created or brought into service. Also, changes to
+ the row status could result in profiles being inadvertently
+ deleted or taken out of service.
+
+ Some of the readable objects in this MIB module (i.e., objects with a
+ MAX-ACCESS other than not-accessible) may be considered sensitive or
+ vulnerable in some network environments. It is thus important to
+ control even GET and/or NOTIFY access to these objects and possibly
+ to even encrypt the values of these objects when sending them over
+ the network via SNMP. These are the tables and objects and their
+ sensitivity/vulnerability:
+
+ o hdsl2ShdslInventoryTable
+
+ Access to these objects would allow an intruder to obtain
+ information about which vendor's equipment is in use on the
+ network. Further, such information is considered sensitive in
+ many environments for competitive reasons.
+
+ * hdsl2ShdslInvVendorID
+ * hdsl2ShdslInvVendorModelNumber
+ * hdsl2ShdslInvVendorSerialNumber
+ * hdsl2ShdslInvVendorEOCSoftwareVersion
+ * hdsl2ShdslInvStandardVersion
+ * hdsl2ShdslInvVendorListNumber
+
+
+
+Sikes, et al. Standards Track [Page 70]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ * hdsl2ShdslInvVendorIssueNumber
+ * hdsl2ShdslInvVendorSoftwareVersion
+ * hdsl2ShdslInvEquipmentCode
+ * hdsl2ShdslInvVendorOther
+ * hdsl2ShdslInvTransmissionModeCapability
+
+ SNMP versions prior to SNMPv3 did not include adequate security.
+ Even if the network itself is secure (for example by using IPsec),
+ even then, there is no control as to who on the secure network is
+ allowed to access and GET/SET (read/change/create/delete) the objects
+ in this MIB module.
+
+ It is RECOMMENDED that implementers consider the security features as
+ provided by the SNMPv3 framework (see [RFC3410], Section 8),
+ including full support for the SNMPv3 cryptographic mechanisms (for
+ authentication and privacy).
+
+ Further, deployment of SNMP versions prior to SNMPv3 is NOT
+ RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
+ enable cryptographic security. It is then a customer/operator
+ responsibility to ensure that the SNMP entity giving access to an
+ instance of this MIB module is properly configured to give access to
+ the objects only to those principals (users) that have legitimate
+ rights to indeed GET or SET (change/create/delete) them.
+
+6. Acknowledgements
+
+ The authors are deeply grateful to the authors of the ADSL LINE MIB
+ (RFC 2662 [RFC2662]), Gregory Bathrick and Faye Ly, as much of the
+ text and structure of this document originate in their documents.
+
+ The authors are also grateful to the authors of FR MFR MIB (RFC 3020
+ [RFC3020]), Prayson Pate, Bob Lynch, and Kenneth Rehbehn, as the
+ majority of the Security Considerations section was lifted from their
+ document.
+
+ The authors also acknowledge the importance of the contributions and
+ suggestions regarding interface indexing structures received from
+ David Horton of CITR.
+
+ The authors are extremely thankful to Bert Wijnen, Randy Presuhn, and
+ C. M. Heard for their extensive review and the many suggestions they
+ provided.
+
+
+
+
+
+
+
+
+Sikes, et al. Standards Track [Page 71]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ Other contributions were received from the following:
+
+ Matt Beanland (Extel Communications)
+ Philip Bergstresser (Adtran)
+ Steve Blackwell (Centillium)
+ Umberto Bonollo (NEC Australia)
+ John Egan (Metalink BroadBand)
+ Yagal Hachmon (RAD)
+ Mark Johnson (Red Point)
+ Sharon Mantin (Orckit)
+ Moti Morgenstern (ECI)
+ Raymond Murphy (Ericsson)
+ Lee Nipper (Verilink)
+ Randy Presuhn (BMC Software)
+ Katy Sherman (Orckit)
+ Mike Sneed (ECI)
+ Jon Turney (DSL Solutions)
+ Aron Wahl (Memotec)
+ Bert Wijnen (Lucent)
+ Jim Wilson (for Mindspeed)
+ Michael Wrobel (Memotec)
+
+7. References
+
+7.1. Normative References
+
+ [G.991.2] Blackwell, S., "Single-Pair High-Speed Digital Subscriber
+ Line (SHDSL) Transceivers", ITU-T G.991.2, December 2003.
+
+ [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
+ Requirement Levels", BCP 14, RFC 2119, March 1997.
+
+ [RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
+ "Structure of Management Information Version 2 (SMIv2)",
+ STD 58, RFC 2578, April 1999.
+
+ [RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
+ "Textual Conventions for SMIv2", STD 58, RFC 2579, April
+ 1999.
+
+ [RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
+ "Conformance Statements for SMIv2", STD 58, RFC 2580,
+ April 1999.
+
+ [RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
+ MIB", RFC 2863, June 2000.
+
+
+
+
+
+Sikes, et al. Standards Track [Page 72]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+ [RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
+ Architecture for Describing Simple Network Management
+ Protocol (SNMP) Management Frameworks", STD 62, RFC 3411,
+ December 2002.
+
+ [RFC3593] Tesink, K., "Textual Conventions for MIB Modules Using
+ Performance History Based on 15 Minute Intervals", RFC
+ 3593, September 2003.
+
+ [T1E1.4] American National Standards Institute, "ANSI T1E1.4/2000-
+ 006", February 2000.
+
+7.2. Informative References
+
+ [RFC2662] Bathrick, G. and F. Ly, "Definitions of Managed Objects
+ for the ADSL Lines", RFC 2662, August 1999.
+
+ [RFC3020] Pate, P., Lynch, B., and K. Rehbehn, "Definitions of
+ Managed Objects for Monitoring and Controlling the UNI/NNI
+ Multilink Frame Relay Function", RFC 3020, December 2000.
+
+ [RFC3276] Ray, B. and R. Abbi, "Definitions of Managed Objects for
+ High Bit-Rate DSL - 2nd generation (HDSL2) and Single-Pair
+ High-Speed Digital Subscriber Line (SHDSL) Lines
+ Processing", RFC 3276, May 2002.
+
+ [RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
+ "Introduction and Applicability Statements for Internet-
+ Standard Management Framework", RFC 3410, December 2002.
+
+ [RFC3418] Presuhn, R., "Management Information Base (MIB) for the
+ Simple Network Management Protocol (SNMP)", STD 62, RFC
+ 3418, December 2002.
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+Sikes, et al. Standards Track [Page 73]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+Authors' Addresses
+
+ Clay Sikes
+ Zhone Technologies, Inc.
+ Florida Design Center
+ 8454 126th Ave. N.
+ Largo, FL 33773
+ US
+
+ Phone: +1 727 530 8257
+ Fax: +1 727 532 5698
+ EMail: csikes@zhone.com
+
+
+ Bob Ray
+ PESA Switching Systems, Inc.
+ 330-A Wynn Drive
+ Huntsville, AL 35805
+ US
+
+ Phone: +1 256 726 9200 ext. 142
+ Fax: +1 256 726 9271
+ EMail: rray@pesa.com
+
+
+ Rajesh Abbi
+ Alcatel USA
+ 2301 Sugar Bush Road
+ Raleigh, NC 27612
+ US
+
+ Phone: +1 919-850-6194
+ Fax: +1 919-850-6670
+ EMail: Rajesh.Abbi@alcatel.com
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+Sikes, et al. Standards Track [Page 74]
+
+RFC 4319 HDSL2-SHDSL-LINE-MIB December 2005
+
+
+Full Copyright Statement
+
+ Copyright (C) The Internet Society (2005).
+
+ This document is subject to the rights, licenses and restrictions
+ contained in BCP 78, and except as set forth therein, the authors
+ retain all their rights.
+
+ This document and the information contained herein are provided on an
+ "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
+ OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
+ ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
+ INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
+ INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
+ WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
+
+Intellectual Property
+
+ The IETF takes no position regarding the validity or scope of any
+ Intellectual Property Rights or other rights that might be claimed to
+ pertain to the implementation or use of the technology described in
+ this document or the extent to which any license under such rights
+ might or might not be available; nor does it represent that it has
+ made any independent effort to identify any such rights. Information
+ on the procedures with respect to rights in RFC documents can be
+ found in BCP 78 and BCP 79.
+
+ Copies of IPR disclosures made to the IETF Secretariat and any
+ assurances of licenses to be made available, or the result of an
+ attempt made to obtain a general license or permission for the use of
+ such proprietary rights by implementers or users of this
+ specification can be obtained from the IETF on-line IPR repository at
+ http://www.ietf.org/ipr.
+
+ The IETF invites any interested party to bring to its attention any
+ copyrights, patents or patent applications, or other proprietary
+ rights that may cover technology that may be required to implement
+ this standard. Please address the information to the IETF at ietf-
+ ipr@ietf.org.
+
+Acknowledgement
+
+ Funding for the RFC Editor function is currently provided by the
+ Internet Society.
+
+
+
+
+
+
+
+Sikes, et al. Standards Track [Page 75]
+