From 4bfd864f10b68b71482b35c818559068ef8d5797 Mon Sep 17 00:00:00 2001 From: Thomas Voss Date: Wed, 27 Nov 2024 20:54:24 +0100 Subject: doc: Add RFC documents --- doc/rfc/rfc4139.txt | 899 ++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 899 insertions(+) create mode 100644 doc/rfc/rfc4139.txt (limited to 'doc/rfc/rfc4139.txt') diff --git a/doc/rfc/rfc4139.txt b/doc/rfc/rfc4139.txt new file mode 100644 index 0000000..7b237ff --- /dev/null +++ b/doc/rfc/rfc4139.txt @@ -0,0 +1,899 @@ + + + + + + +Network Working Group D. Papadimitriou +Request for Comments: 4139 Alcatel +Category: Informational J. Drake + Boeing + J. Ash + ATT + A. Farrel + Old Dog Consulting + L. Ong + Ciena + July 2005 + + + Requirements for Generalized MPLS (GMPLS) Signaling Usage + and Extensions for Automatically Switched Optical Network (ASON) + +Status of This Memo + + This memo provides information for the Internet community. It does + not specify an Internet standard of any kind. Distribution of this + memo is unlimited. + +Copyright Notice + + Copyright (C) The Internet Society (2005). + +Abstract + + The Generalized Multi-Protocol Label Switching (GMPLS) suite of + protocols has been defined to control different switching + technologies and different applications. These include support for + requesting Time Division Multiplexing (TDM) connections, including + Synchronous Optical Network (SONET)/Synchronous Digital Hierarchy + (SDH) and Optical Transport Networks (OTNs). + + This document concentrates on the signaling aspects of the GMPLS + suite of protocols. It identifies the features to be covered by the + GMPLS signaling protocol to support the capabilities of an + Automatically Switched Optical Network (ASON). This document + provides a problem statement and additional requirements for the + GMPLS signaling protocol to support the ASON functionality. + + + + + + + + + + +Papadimitriou, et al. Informational [Page 1] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + +1. Introduction + + The Generalized Multi-Protocol Label Switching (GMPLS) suite of + protocol specifications provides support for controlling different + switching technologies and different applications. These include + support for requesting Time Division Multiplexing (TDM) connections, + including Synchronous Optical Network (SONET)/Synchronous Digital + Hierarchy (SDH) (see [ANSI-T1.105] and [ITU-T-G.707], respectively), + and Optical Transport Networks (see [ITU-T-G.709]). In addition, + there are certain capabilities needed to support Automatically + Switched Optical Networks control planes (their architecture is + defined in [ITU-T-G.8080]). These include generic capabilities such + as call and connection separation, along with more specific + capabilities such as support of soft permanent connections. + + This document concentrates on requirements related to the signaling + aspects of the GMPLS suite of protocols. It discusses the functional + requirements required to support Automatically Switched Optical + Networks that may lead to additional extensions to GMPLS signaling + (see [RFC3471] and [RFC3473]) to support these capabilities. In + addition to ASON signaling requirements, this document includes GMPLS + signaling requirements that pertain to backward compatibility + (Section 5). A terminology section is provided in the Appendix. + +2. Conventions Used in This Document + + The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", + "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this + document are to be interpreted as described in [RFC2119]. + + While [RFC2119] describes interpretations of these key words in terms + of protocol specifications and implementations, they are used in this + document to describe design requirements for protocol extensions. + +3. Problem Statement + + The Automatically Switched Optical Network (ASON) architecture + describes the application of an automated control plane for + supporting both call and connection management services (for a + detailed description see [ITU-T-G.8080]). The ASON architecture + describes a reference architecture, (i.e., it describes functional + components, abstract interfaces, and interactions). + + The ASON model distinguishes reference points (representing points of + information exchange) defined (1) between a user (service requester) + and a service provider control domain, a.k.a. user-network interface + (UNI), (2) between control domains, a.k.a. external network-network + interface (E-NNI), and, (3) within a control domain, a.k.a. internal + + + +Papadimitriou, et al. Informational [Page 2] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + + network-network interface (I-NNI). The I-NNI and E-NNI interfaces + are between protocol controllers, and may or may not use transport + plane (physical) links. It must not be assumed that there is a one- + to-one relationship between control plane interfaces and transport + plane (physical) links, control plane entities and transport plane + entities, or control plane identifiers for transport plane resources. + + This document describes requirements related to the use of GMPLS + signaling (in particular, [RFC3471] and [RFC3473]) to provide call + and connection management (see [ITU-T-G.7713]). The functionality to + be supported includes: + + (a) soft permanent connection capability + (b) call and connection separation + (c) call segments + (d) extended restart capabilities during control plane failures + (e) extended label association + (f) crankback capability + (g) additional error cases + +4. Requirements for Extending Applicability of GMPLS to ASON + + The following sections detail the signaling protocol requirements for + GMPLS to support the ASON functions listed in Section 3. ASON + defines a reference model and functions (information elements) to + enable end-to-end call and connection support by a protocol across + the respective interfaces, regardless of the particular choice of + protocol(s) used in a network. ASON does not restrict the use of + other protocols or the protocol-specific messages used to support the + ASON functions. Therefore, the support of these ASON functions by a + protocol shall not be restricted by (i.e., must be strictly + independent of and agnostic to) any particular choice of UNI, I-NNI, + or E-NNI used elsewhere in the network. To allow for interworking + between different protocol implementations, [ITU-T-G.7713] recognizes + that an interworking function may be needed. + + In support of the G.8080 end-to-end call model across different + control domains, end-to-end signaling should be facilitated + regardless of the administrative boundaries, protocols within the + network, or the method of realization of connections within any part + of the network. This implies the need for a clear mapping of ASON + signaling requests between GMPLS control domains and non-GMPLS + control domains. This document provides signaling requirements for + G.8080 distributed call and connection management based on GMPLS, + within a GMPLS based control domain (I-NNI), and between GMPLS based + control domains (E-NNI). It does not restrict use of other (non + GMPLS) protocols to be used within a control domain or as an E-NNI or + UNI. Interworking aspects related to the use of non-GMPLS protocols, + + + +Papadimitriou, et al. Informational [Page 3] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + + such as UNI, E-NNI, or I-NNI -- including mapping of non-GMPLS + protocol signaling requests to corresponding ASON signaling + functionality and support of non-GMPLS address formats -- is not + within the scope of the GMPLS signaling protocol. Interworking + aspects are implementation-specific and strictly under the + responsibility of the interworking function and, thus, outside the + scope of this document. + + By definition, any User-Network Interface (UNI) that is compliant + with [RFC3473] (e.g., [GMPLS-OVERLAY] and [GMPLS-VPN]) is considered + to be included within the GMPLS suite of protocols and MUST be + supported by the ASON GMPLS signaling functionality. + + Compatibility aspects of non-GMPLS systems (nodes) within a GMPLS + control domain (i.e., the support of GMPLS systems and other systems + that utilize other signaling protocols or some that may not support + any signaling protocols) is described. For example, Section 4.5, + 'Support for Extended Label Association', covers the requirements for + when a non-GMPLS capable sub-network is introduced or when nodes do + not support any signaling protocols. + +4.1. Support for Soft Permanent Connection (SPC) Capability + + A Soft Permanent Connection (SPC) is a combination of a permanent + connection at the source user-to-network side, a permanent connection + at the destination user-to-network side, and a switched connection + within the network. An Element Management System (EMS) or a Network + Management System (NMS) typically initiates the establishment of the + switched connection by communicating with the node that initiates the + switched connection (also known as the ingress node). The latter + then sets the connection using the distributed GMPLS signaling + protocol. For the SPC, the communication method between the EMS/NMS + and the ingress node is beyond the scope of this document (as it is + for any other function described in this document). + + The end-to-end connection is thus created by associating the incoming + interface of the ingress node with the switched connection within the + network, along with the outgoing interface of the switched connection + terminating network node (also referred to as egress node). An SPC + connection is illustrated in the following figure. This shows the + user's node A connected to a provider's node B via link #1, the + user's node Z connected to a provider's node Y via link #3, and an + abstract link #2 connecting the provider's node B and node Y. Nodes + B and Y are referred to as the ingress and egress (respectively) of + the network switched connection. + + + + + + +Papadimitriou, et al. Informational [Page 4] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + + --- --- --- --- + | A |--1--| B |-----2-//------| Y |--3--| Z | + --- --- --- --- + + In this instance, the connection on link #1 and link #3 are both + provisioned (permanent connections that may be simple links). In + contrast, the connection over link #2 is set up using the distributed + control plane. Thus, the SPC is composed of the stitching of link + #1, #2, and #3. + + Thus, to support the capability of requesting an SPC connection: + + - The GMPLS signaling protocol MUST be capable of supporting the + ability to indicate the outgoing link and label information used + when setting up the destination provisioned connection. + + - In addition, due to the inter-domain applicability of ASON + networks, the GMPLS signaling protocol SHOULD also support + indication of the service level requested for the SPC. In cases + where an SPC spans multiple domains, indication of both source and + destination endpoints controlling the SPC request MAY be needed. + These MAY be done via the source and destination signaling + controller addresses. + + Note that the association at the ingress node, between the permanent + connection and the switched connection, is an implementation matter + that may be under the control of the EMS/NMS and is not within the + scope of the signaling protocol. Therefore, it is outside the scope + of this document. + +4.2. Support for Call and Connection Separation + + A call may be simply described as "An association between endpoints + that supports an instance of a service" [ITU-T-G.8080]. Thus, it can + be considered a service provided between two end-points, wherein + several calls may exist between them. Multiple connections may be + associated with each call. The call concept provides an abstract + relationship between two users. This relationship describes (or + verifies) the extent to which users are willing to offer (or accept) + service to/from each other. Therefore, a call does not provide the + actual connectivity for transmitting user traffic; it only builds a + relationship by which subsequent connections may be made. + + A call MAY be associated with zero, one, or multiple connections. + For the same call, connections MAY be of different types and each + connection MAY exist independently of other connections (i.e., each + connection is setup and released with separate signaling messages). + + + + +Papadimitriou, et al. Informational [Page 5] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + + The concept of the call allows for a better flexibility in how end- + points set up connections and how networks offer services to users. + For example, a call allows: + + - An upgrade strategy for control plane operations, where a call + control component (service provisioning) may be separate from the + actual nodes hosting the connections (where the connection control + component may reside). + + - Identification of the call initiator (with both network call + controller, as well as destination user) prior to connection, + which may result in decreasing contention during resource + reservation. + + - General treatment of multiple connections, which may be associated + for several purposes; for example, a pair of working and recovery + connections may belong to the same call. + + To support the introduction of the call concept, GMPLS signaling + SHOULD include a call identification mechanism and SHOULD allow for + end-to-end call capability exchange. + + For instance, a feasible structure for the call identifier (to + guarantee global uniqueness) MAY concatenate a globally unique fixed + ID (e.g., may be composed of country code or carrier code) with an + operator specific ID (where the operator specific ID may be composed + of a unique access point code - such as source node address - and a + local identifier). Other formats SHALL also be possible, depending + on the call identification conventions between the parties involved + in the call setup process. + +4.3. Support for Call Segments + + As described in [ITU-T-G.8080], call segmentation MAY be applied when + a call crosses several control domains. As such, when the call + traverses multiple control domains, an end-to-end call MAY consist of + multiple call segments. For a given end-to-end call, each call + segment MAY have one or more associated connections, and the number + of connections associated with each call segment MAY be different. + + The initiating caller interacts with the called party by means of one + or more intermediate network call controllers, located at control + domain boundaries (i.e., at inter-domain reference points, UNI or + E-NNI). Call segment capabilities are defined by the policies + associated at these reference points. + + + + + + +Papadimitriou, et al. Informational [Page 6] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + + This capability allows for independent (policy based) choices of + signaling, concatenation, data plane protection, and control plane + driven recovery paradigms in different control domains. + +4.4. Support for Extended Restart Capabilities + + Various types of failures may occur, affecting the ASON control + plane. Requirements placed on control plane failure recovery by + [ITU-T-G.8080] include: + + - Any control plane failure (i.e., single or multiple control + channel and/or controller failure and any combination thereof) + MUST NOT result in releasing established calls and connections + (including the corresponding transport plane connections). + + - Upon recovery from a control plane failure, the recovered control + entity MUST have the ability to recover the status of the calls + and the connections established before failure occurrence. + + - Upon recovery from a control plane failure, the recovered control + entity MUST have the ability to recover the connectivity + information of its neighbors. + + - Upon recovery from a control plane failure, the recovered control + entity MUST have the ability to recover the association between + the call and its associated connections. + + - Upon recovery from a control plane failure, calls and connections + in the process of being established (i.e., pending call/connection + setup requests) SHOULD be released or continued (with setup). + + - Upon recovery from a control plane failure, calls and connections + in the process of being released MUST be released. + +4.5. Support for Extended Label Association + + It is an ASON requirement to enable support for G.805 [ITU-T-G.805] + serial compound links. The text below provides an illustrative + example of such a scenario, and the associated requirements. + + Labels are defined in GMPLS (see [RFC3471]) to provide information on + the resources used on a link local basis for a particular connection. + The labels may range from specifying a particular timeslot, + indicating a particular wavelength, or to identifying a particular + port/fiber. In the ASON context, the value of a label may not be + consistent across a link. For example, the figure below illustrates + + + + + +Papadimitriou, et al. Informational [Page 7] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + + the case where two GMPLS capable nodes (A and Z) are interconnected + across two non-GMPLS capable nodes (B and C), where all of these + nodes are SONET/SDH nodes, providing, for example, a VC-4 service. + + ----- ----- + | | --- --- | | + | A |---| B |---| C |---| Z | + | | --- --- | | + ----- ----- + + Labels have an associated implicit imposed structure based on + [GMPLS-SONET] and [GMPLS-OTN]. Thus, once the local label is + exchanged with its neighboring control plane node, the structure of + the local label may not be significant to the neighbor node, as the + association between the local and the remote label may not + necessarily be the same. This issue does not present a problem in + simple point-to-point connections between two control plane-enabled + nodes in which the timeslots are mapped 1:1 across the interface. + However, if a non-GMPLS capable sub-network is introduced between + these nodes (as in the above figure, where the sub-network provides + re-arrangement capability for the timeslots), label scoping may + become an issue. + + In this context, there is an implicit assumption that the data plane + connections between the GMPLS capable edges already exist prior to + any connection request. For instance, node A's outgoing VC-4's + timeslot #1 (with SUKLM label=[1,0,0,0,0]), as defined in + [GMPLS-SONET]), may be mapped onto node B's outgoing VC-4's timeslot + #6 (label=[6,0,0,0,0]), or may be mapped onto node C's outgoing VC- + 4's timeslot #4 (label=[4,0,0,0,0]). Thus, by the time node Z + receives the request from node A with label=[1,0,0,0,0], node Z's + local label and timeslot no longer correspond to the received label + and timeslot information. + + As such, to support this capability, a label association mechanism + SHOULD be used by the control plane node to map the received (remote) + label into a locally significant label. The information necessary to + allow mapping from a received label value to a locally significant + label value can be derived in several ways including: + + - Manual provisioning of the label association + + - Discovery of the label association + + Either method MAY be used. In case of dynamic association, the + discovery mechanism operates at the timeslot/label level before the + connection request is processed at the ingress node. Note that in + the case where two nodes are directly connected, no association is + + + +Papadimitriou, et al. Informational [Page 8] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + + required. In particular, for directly connected TDM interfaces, no + mapping function (at all) is required due to the implicit label + structure (see [GMPLS-SONET] and [GMPLS-OTN]). In these instances, + the label association function provides a one-to-one mapping of the + received to local label values. + +4.6. Support for Crankback + + Crankback has been identified as an important requirement for ASON + networks. Upon a setup failure, it allows a connection setup request + to be retried on an alternate path that detours around a blocked link + or node (e.g., because a link or a node along the selected path has + insufficient resources). + + Crankback mechanisms MAY also be applied during connection recovery + by indicating the location of the failed link or node. This would + significantly improve the successful recovery ratio for failed + connections, especially in situations where a large number of setup + requests are simultaneously triggered. + + The following mechanisms are assumed during crankback signaling: + + - The blocking resource (link or node) MUST be identified and + returned in the error response message to the repair node (that + may or may not be the ingress node); it is also assumed that this + process will occur within a limited period of time. + + - The computation (from the repair node) of an alternate path around + the blocking link or node that satisfies the initial connection + constraints. + + - The re-initiation of the connection setup request from the repair + node (i.e., the node that has intercepted and processed the error + response message). + + The following properties are expected for crankback signaling: + + - Error information persistence: the entity that computes the + alternate (re-routing) path SHOULD store the identifiers of the + blocking resources, as indicated in the error message, until the + connection is successfully established or until the node abandons + rerouting attempts. Since crankback may happen more than once + while establishing a specific connection, the history of all + experienced blockages for this connection SHOULD be maintained (at + least until the routing protocol updates the state of this + information) to perform an accurate path computation that will + avoid all blockages. + + + + +Papadimitriou, et al. Informational [Page 9] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + + - Rerouting attempts limitation: to prevent an endless repetition of + connection setup attempts (using crankback information), the + number of retries SHOULD be strictly limited. The maximum number + of crankback rerouting attempts allowed MAY be limited per + connection or per node: + + - When the number of retries at a particular node is exceeded, + the node that is currently handling the failure reports the + error message upstream to the next repair node, where further + rerouting attempts MAY be performed. It is important that the + crankback information provided indicate that re-routing through + this node will not succeed. + + - When the maximum number of retries for a specific connection + has been exceeded, the repair node that is handling the current + failure SHOULD send an error message upstream to indicate the + "Maximum number of re-routings exceeded". This error message + will be sent back to the ingress node with no further rerouting + attempts. Then, the ingress node MAY choose to retry the + connection setup according to local policy, using its original + path, or computing a path that avoids the blocking resources. + + Note: After several retries, a given repair point MAY be unable to + compute a path to the destination node that avoids all of the + blockages. In this case, it MUST pass the error message upstream + to the next repair point. + +4.7. Support for Additional Error Cases + + To support the ASON network, the following additional category of + error cases are defined: + + - Errors associated with basic call and soft permanent connection + support. For example, these MAY include incorrect assignment of + IDs for the Call or an invalid interface ID for the soft permanent + connection. + + - Errors associated with policy failure during processing of the new + call and soft permanent connection capabilities. These MAY + include unauthorized requests for the particular capability. + + - Errors associated with incorrect specification of the service + level. + + + + + + + + +Papadimitriou, et al. Informational [Page 10] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + +5. Backward Compatibility + + As noted above, in support of GMPLS protocol requirements, any + extensions to the GMPLS signaling protocol, in support of the + requirements described in this document, MUST be backward compatible. + + Backward compatibility means that in a network of nodes, where some + support GMPLS signaling extensions to facilitate the functions + described in this document, and some do not, it MUST be possible to + set up conventional connections (as described by [RFC3473]) between + any arbitrary pair of nodes and to traverse any arbitrary set of + nodes. Further, the use of any GMPLS signaling extensions to set up + calls or connections that support the functions described in this + document MUST not perturb existing conventional connections. + + Additionally, when transit nodes that do not need to participate in + the new functions described in this document lie on the path of a + call or connection, the GMPLS signaling extensions MUST be such that + those transit nodes are able to participate in the establishment of a + call or connection by passing the setup information onwards, + unmodified. + + Lastly, when a transit or egress node is called upon to support a + function described in this document, but does not support the + function, the GMPLS signaling extensions MUST be such that they can + be rejected by pre-existing GMPLS signaling mechanisms in a way that + is not detrimental to the network as a whole. + +6. Security Considerations + + Per [ITU-T-G.8080], it is not possible to establish a connection in + advance of call setup completion. Also, policy and authentication + procedures are applied prior to the establishment of the call (and + can then also be restricted to connection establishment in the + context of this call). + + This document introduces no new security requirements to GMPLS + signaling (see [RFC3471]). + +7. Acknowledgements + + The authors would like to thank Nic Larkin, Osama Aboul-Magd, and + Dimitrios Pendarakis for their contribution to the previous version + of this document, Zhi-Wei Lin for his contribution to this document, + Deborah Brungard for her input and guidance in our understanding of + the ASON model, and Gert Grammel for his decryption effort during the + reduction of some parts of this document. + + + + +Papadimitriou, et al. Informational [Page 11] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + +8. References + +8.1. Normative References + + [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate + Requirement Levels", BCP 14, RFC 2119, March 1997. + + [RFC3471] Berger, L., "Generalized Multi-Protocol Label + Switching (GMPLS) Signaling Functional Description", + RFC 3471, January 2003. + + [RFC3473] Berger, L., "Generalized Multi-Protocol Label + Switching (GMPLS) Signaling Resource ReserVation + Protocol-Traffic Engineering (RSVP-TE) Extensions", + RFC 3473, January 2003. + +8.2. Informative References + + [ANSI-T1.105] ANSI, "Synchronous Optical Network (SONET): Basic + Description Including Multiplex Structure, Rates, and + Formats", T1.105, October 2000. + + [GMPLS-OTN] Papadimitriou, D., Ed., "Generalized MPLS (GMPLS) + Signaling Extensions for G.709 Optical Transport + Networks Control", Work in Progress, January 2005. + + [GMPLS-OVERLAY] Swallow, G., Drake, J., Ishimatsu, H., and Y. + Rekhter, "Generalize Multiprotocol Label Switching + (GMPLS) User-Network Interface (UNI): Resource + ReserVation Protocol-Traffic Engineering (RSVP-TE) + Support for the Overlay Model", Work in Progress, + October 2004. + + [GMPLS-SONET] Mannie, E. and D. Papadimitriou, "Generalized Multi- + Protocol Label Switching (GMPLS) Extensions for + Synchronous Optical Network (SONET) and Synchronous + Digital Hierarchy (SDH) Control", RFC 3946, October + 2004. + + [GMPLS-VPN] Ould-Brahim, H. and Y. Rekhter, Eds., "GVPN Services: + Generalized VPN Services using BGP and GMPLS + Toolkit", Work in Progress, May 2004. + + [ITU-T-G.707] ITU-T, "Network Node Interface for the Synchronous + Digital Hierarchy (SDH)", Recommendation G.707, + October 2000. + + + + + +Papadimitriou, et al. Informational [Page 12] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + + [ITU-T-G.709] ITU-T, "Interface for the Optical Transport Network + (OTN)", Recommendation G.709 (and Amendment 1), + February 2001 (October 2001). http://www.itu.int + + [ITU-T-G.7713] ITU-T "Distributed Call and Connection Management", + Recommendation G.7713/Y.1304, November 2001. + http://www.itu.int + + [ITU-T-G.805] ITU-T, "Generic functional architecture of transport + networks)", Recommendation G.805, March 2000. + http://www.itu.int + + [ITU-T-G.8080] ITU-T "Architecture for the Automatically Switched + Optical Network (ASON)", Recommendation + G.8080/Y.1304, November 2001 (and Revision, January + 2003). http://www.itu.int + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +Papadimitriou, et al. Informational [Page 13] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + +Appendix - Terminology + + This document makes use of the following terms: + + Administrative domain: See Recommendation G.805 [ITU-T-G.805]. + + Call: Association between endpoints that supports an instance of a + service. + + Connection: Concatenation of link connections and sub-network + connections that allows the transport of user information between the + ingress and egress points of a sub-network. + + Control Plane: Performs the call control and connection control + functions. The control plane sets up and releases connections + through signaling, and may restore a connection in case of a failure. + + (Control) Domain: Represents a collection of entities that are + grouped for a particular purpose. G.8080 applies this G.805 + recommendation concept (that defines two particular forms: the + administrative domain and the management domain) to the control plane + in the form of a control domain. Entities grouped in a control + domain are components of the control plane. + + External NNI (E-NNI): Interfaces are located between protocol + controllers that are situated between control domains. + + Internal NNI (I-NNI): Interfaces are located between protocol + controllers within control domains. + + Link: See Recommendation G.805 [ITU-T-G.805]. + + Management Plane: Performs management functions for the Transport + Plane, the control plane, and the system as a whole. It also + provides coordination between all the planes. The following + management functional areas are performed in the management plane: + performance, fault, configuration, accounting, and security + management. + + Management Domain: See Recommendation G.805 [ITU-T-G.805]. + + Transport Plane: Provides bi-directional or unidirectional transfer + of user information, from one location to another. It can also + provide transfer of some control and network management information. + The Transport Plane is layered and is equivalent to the Transport + Network defined in G.805 [ITU-T-G.805]. + + + + + +Papadimitriou, et al. Informational [Page 14] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + + User Network Interface (UNI): Interfaces are located between protocol + controllers, between a user and a control domain. + +Authors' Addresses + + Dimitri Papadimitriou + Alcatel + Francis Wellesplein 1, + B-2018 Antwerpen, Belgium + + Phone: +32 3 2408491 + EMail: dimitri.papadimitriou@alcatel.be + + + John Drake + Boeing Satellite Systems + 2300 East Imperial Highway + El Segundo, CA 90245 + + EMail: John.E.Drake2@boeing.com + + + Adrian Farrel + Old Dog Consulting + + Phone: +44 (0) 1978 860944 + EMail: adrian@olddog.co.uk + + + Gerald R. Ash + ATT + AT&T Labs, Room MT D5-2A01 + 200 Laurel Avenue + Middletown, NJ 07748, USA + + EMail: gash@att.com + + + Lyndon Ong + Ciena + PO Box 308 + Cupertino, CA 95015, USA + + EMail: lyong@ciena.com + + + + + + + +Papadimitriou, et al. Informational [Page 15] + +RFC 4139 GMPLS Signaling Usage and Extensions for ASON July 2005 + + +Full Copyright Statement + + Copyright (C) The Internet Society (2005). + + This document is subject to the rights, licenses and restrictions + contained in BCP 78, and except as set forth therein, the authors + retain all their rights. + + This document and the information contained herein are provided on an + "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS + OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET + ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, + INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE + INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED + WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. + +Intellectual Property + + The IETF takes no position regarding the validity or scope of any + Intellectual Property Rights or other rights that might be claimed to + pertain to the implementation or use of the technology described in + this document or the extent to which any license under such rights + might or might not be available; nor does it represent that it has + made any independent effort to identify any such rights. Information + on the procedures with respect to rights in RFC documents can be + found in BCP 78 and BCP 79. + + Copies of IPR disclosures made to the IETF Secretariat and any + assurances of licenses to be made available, or the result of an + attempt made to obtain a general license or permission for the use of + such proprietary rights by implementers or users of this + specification can be obtained from the IETF on-line IPR repository at + http://www.ietf.org/ipr. + + The IETF invites any interested party to bring to its attention any + copyrights, patents or patent applications, or other proprietary + rights that may cover technology that may be required to implement + this standard. Please address the information to the IETF at ietf- + ipr@ietf.org. + +Acknowledgement + + Funding for the RFC Editor function is currently provided by the + Internet Society. + + + + + + + +Papadimitriou, et al. Informational [Page 16] + -- cgit v1.2.3