From 4bfd864f10b68b71482b35c818559068ef8d5797 Mon Sep 17 00:00:00 2001 From: Thomas Voss Date: Wed, 27 Nov 2024 20:54:24 +0100 Subject: doc: Add RFC documents --- doc/rfc/rfc4874.txt | 1515 +++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 1515 insertions(+) create mode 100644 doc/rfc/rfc4874.txt (limited to 'doc/rfc/rfc4874.txt') diff --git a/doc/rfc/rfc4874.txt b/doc/rfc/rfc4874.txt new file mode 100644 index 0000000..55968c9 --- /dev/null +++ b/doc/rfc/rfc4874.txt @@ -0,0 +1,1515 @@ + + + + + + +Network Working Group CY. Lee +Request for Comments: 4874 A. Farrel +Updates: 3209, 3473 Old Dog Consulting +Category: Standards Track S. De Cnodder + Alcatel-Lucent + April 2007 + + + Exclude Routes - Extension to + Resource ReserVation Protocol-Traffic Engineering (RSVP-TE) + +Status of This Memo + + This document specifies an Internet standards track protocol for the + Internet community, and requests discussion and suggestions for + improvements. Please refer to the current edition of the "Internet + Official Protocol Standards" (STD 1) for the standardization state + and status of this protocol. Distribution of this memo is unlimited. + +Copyright Notice + + Copyright (C) The IETF Trust (2007). + +Abstract + + This document specifies ways to communicate route exclusions during + path setup using Resource ReserVation Protocol-Traffic Engineering + (RSVP-TE). + + The RSVP-TE specification, "RSVP-TE: Extensions to RSVP for LSP + Tunnels" (RFC 3209) and GMPLS extensions to RSVP-TE, "Generalized + Multi-Protocol Label Switching (GMPLS) Signaling Resource ReserVation + Protocol-Traffic Engineering (RSVP-TE) Extensions" (RFC 3473) allow + abstract nodes and resources to be explicitly included in a path + setup, but not to be explicitly excluded. + + In some networks where precise explicit paths are not computed at the + head end, it may be useful to specify and signal abstract nodes and + resources that are to be explicitly excluded from routes. These + exclusions may apply to the whole path, or to parts of a path between + two abstract nodes specified in an explicit path. How Shared Risk + Link Groups (SRLGs) can be excluded is also specified in this + document. + + + + + + + + +Lee, et al. Standards Track [Page 1] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + +Table of Contents + + 1. Introduction ....................................................3 + 1.1. Requirements Notation ......................................4 + 1.2. Scope of Exclude Routes ....................................4 + 1.3. Relationship to MPLS TE MIB ................................5 + 2. Shared Risk Link Groups .........................................6 + 2.1. SRLG Subobject .............................................6 + 3. Exclude Route List ..............................................7 + 3.1. EXCLUDE_ROUTE Object (XRO) .................................7 + 3.1.1. IPv4 Prefix Subobject ...............................8 + 3.1.2. IPv6 Prefix Subobject ...............................9 + 3.1.3. Unnumbered Interface ID Subobject ..................10 + 3.1.4. Autonomous System Number Subobject .................10 + 3.1.5. SRLG Subobject .....................................11 + 3.2. Processing Rules for the EXCLUDE_ROUTE Object (XRO) .......11 + 4. Explicit Exclusion Route .......................................13 + 4.1. Explicit Exclusion Route Subobject (EXRS) .................13 + 4.2. Processing Rules for the Explicit Exclusion Route + Subobject (EXRS) ..........................................15 + 5. Processing of XRO together with EXRS ...........................16 + 6. Minimum Compliance .............................................16 + 7. Security Considerations ........................................16 + 8. IANA Considerations ............................................17 + 8.1. New ERO Subobject Type ....................................17 + 8.2. New RSVP-TE Class Numbers .................................18 + 8.3. New Error Codes ...........................................18 + 9. Acknowledgments ................................................19 + 10. References ....................................................19 + 10.1. Normative References .....................................19 + 10.2. Informative References ...................................19 + Appendix A. Applications ..........................................21 + A.1. Inter-Area LSP Protection .................................21 + A.2. Inter-AS LSP Protection ...................................22 + A.3. Protection in the GMPLS Overlay Model .....................24 + A.4. LSP Protection inside a Single Area .......................25 + + + + + + + + + + + + + + + +Lee, et al. Standards Track [Page 2] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + +1. Introduction + + The RSVP-TE specification [RFC3209] and GMPLS extensions [RFC3473] + allow abstract nodes and resources to be explicitly included in a + path setup, using the Explicit Route Object (ERO). + + In some systems, it may be useful to specify and signal abstract + nodes and resources that are to be explicitly excluded from routes. + This may be because loose hops or abstract nodes need to be prevented + from selecting a route through a specific resource. This is a + special case of distributed path calculation in the network. + + For example, route exclusion could be used in the case where two + non-overlapping Label Switched Paths (LSPs) are required. In this + case, one option might be to set up one path and collect its route + using route recording, and then to exclude the routers on that first + path from the setup for the second path. Another option might be to + set up two parallel backbones, dual home the provider edge (PE) + routers to both backbones, and then exclude the local router on + backbone A the first time that you set up an LSP (to a particular + distant PE), and exclude the local router on backbone B the second + time that you set up an LSP. + + Two types of exclusions are required: + + 1. Exclusion of certain abstract nodes or resources on the whole + path. This set of abstract nodes is referred to as the Exclude + Route list. + + 2. Exclusion of certain abstract nodes or resources between a + specific pair of abstract nodes present in an ERO. Such specific + exclusions are referred to as Explicit Exclusion Route. + + To convey these constructs within the signaling protocol, a new RSVP + object and a new ERO subobject are introduced respectively. + + - A new RSVP-TE object is introduced to convey the Exclude Route + list. This object is the EXCLUDE_ROUTE object (XRO). + + - The second type of exclusion is achieved through a modification to + the existing ERO. A new ERO subobject type the Explicit Exclusion + Route Subobject (EXRS) is introduced to indicate an exclusion + between a pair of included abstract nodes. + + The knowledge of SRLGs, as defined in [RFC4216], may be used to + compute diverse paths that can be used for protection. In systems + where it is useful to signal exclusions, it may be useful to signal + SRLGs to indicate groups of resources that should be excluded on the + + + +Lee, et al. Standards Track [Page 3] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + + whole path or between two abstract nodes specified in an explicit + path. + + This document introduces a subobject to indicate an SRLG to be + signaled in either of the two exclusion methods described above. + This document does not assume or preclude any other usage for this + subobject. This subobject might also be appropriate for use within + an Explicit Route object (ERO) or Record Route object (RRO), but this + is outside the scope of this document. + +1.1. Requirements Notation + + The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", + "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this + document are to be interpreted as described in [RFC2119]. + +1.2. Scope of Exclude Routes + + This document does not preclude a route exclusion from listing + arbitrary nodes or network elements to avoid. The intent is, + however, to indicate only the minimal number of subobjects to be + explicitly avoided. For instance, it may be necessary to signal only + the SRLGs (or Shared Risk Link Groups) to avoid. That is, the route + exclusion is not intended to define the actual route by listing all + of the choices to exclude at each hop, but rather to constrain the + normal route selection process where loose hops or abstract nodes are + to be expanded by listing certain elements to be avoided. + + It is envisaged that most of the conventional inclusion subobjects + are specified in the signaled ERO only for the area where they are + pertinent. The number of subobjects to be avoided, specified in the + signaled XRO, may be constant throughout the whole path setup, or the + subobjects to be avoided may be removed from the XRO as they become + irrelevant in the subsequent hops of the path setup. + + For example, consider an LSP that traverses multiple computation + domains. A computation domain may be an area in the administrative + or IGP sense, or may be an arbitrary division of the network for + active management and path computational purposes. Let the primary + path be (Ingress, A1, A2, AB1, B1, B2, BC1, C1, C2, Egress) where: + + - Xn denotes a node in domain X, and + + - XYn denotes a node on the border of domain X and domain Y. + + Note that Ingress is a node in domain A, and Egress is a node in + domain C. This is shown in Figure 1 where the domains correspond + with areas. + + + +Lee, et al. Standards Track [Page 4] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + + area A area B area C + <-------------------> <----------------> <------------------> + + Ingress-----A1----A2----AB1----B1----B2----BC1----C1----C2----Egress + ^ \ / | \ / | \ / + | \ / | \ / | \ / + | A3----------A4--AB2--B3--------B4--BC2--C3----------C4 + | ^ ^ + | | | + | | | + | | ERO: (C3-strict, C4-strict, + | | Egress-strict) + | | XRO: Not needed + | | + | ERO: (B3-strict, B4-strict, BC2-strict, Egress-loose) + | XRO: (BC1, C1, C2) + | + ERO: (A3-strict, A4-strict, AB2-strict, Egress-loose) + XRO: (AB1, B1, B2, BC1, C1, C2, Egress) + + Figure 1: Domains Corresponding to IGP Areas + + Consider the establishment of a node-diverse protection path in the + example above. The protection path must avoid all nodes on the + primary path. The exclusions for area A are handled during + Constrained Shortest Path First (CSPF) computation at Ingress, so the + ERO and XRO signaled at Ingress could be (A3-strict, A4-strict, + AB2-strict, Egress-loose) and (AB1, B1, B2, BC1, C1, C2), + respectively. At AB2, the ERO and XRO could be (B3-strict, B4- + strict, BC2-strict, Egress-loose) and (BC1, C1, C2), respectively. + At BC2, the ERO could be (C3-strict, C4-strict, Egress-strict) and an + XRO is not needed from BC2 onwards. + + In general, consideration SHOULD be given (as with explicit route) to + the size of signaled data and the impact on the signaling protocol. + +1.3. Relationship to MPLS TE MIB + + [RFC3812] defines managed objects for managing and modeling MPLS- + based traffic engineering. Included in [RFC3812] is a means to + configure explicit routes for use on specific LSPs. This + configuration allows the exclusion of certain resources. + + In systems where the full explicit path is not computed at the + ingress (or at a path computation site for use at the ingress), it + may be necessary to signal those exclusions. This document offers a + means of doing this signaling. + + + + +Lee, et al. Standards Track [Page 5] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + +2. Shared Risk Link Groups + + The identifier of an SRLG is defined as a 32-bit quantity in + [RFC4202]. An SRLG subobject is introduced such that it can be used + in the exclusion methods as described in the following sections. + This document does not assume or preclude any other usage for this + subobject. This subobject might also be appropriate for use within + Explicit Route object (ERO) or Record Route object (RRO), but this is + outside the scope of this document. + +2.1. SRLG Subobject + + The new SRLG subobject is defined by this document as follows. Its + format is modeled on the ERO subobjects defined in [RFC3209]. + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |L| Type | Length | SRLG Id (4 bytes) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | SRLG Id (continued) | Reserved | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + L + The L bit is an attribute of the subobject. The L bit is set + if the subobject represents a loose hop in the explicit route. + If the bit is not set, the subobject represents a strict hop in + the explicit route. + + For exclusions (as used by XRO and EXRS defined in this + document), the L bit SHOULD be set to zero and ignored. + + Type + The type of the subobject (34) + + Length + The Length contains the total length of the subobject in bytes, + including the Type and Length fields. The Length is always 8. + + SRLG Id + The 32-bit identifier of the SRLG. + + Reserved + This field is reserved. It SHOULD be set to zero on + transmission and MUST be ignored on receipt. + + + + + + +Lee, et al. Standards Track [Page 6] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + +3. Exclude Route List + + The exclude route identifies a list of abstract nodes that should not + be traversed along the path of the LSP being established. It is + RECOMMENDED that the size of the exclude route list be limited to a + value local to the node originating the exclude route list. + +3.1. EXCLUDE_ROUTE Object (XRO) + + Abstract nodes to be excluded from the path are specified via the + EXCLUDE_ROUTE object (XRO). + + Currently, one C_Type is defined, Type 1 EXCLUDE_ROUTE. The + EXCLUDE_ROUTE object has the following format: + + Class = 232, C_Type = 1 + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | | + // (Subobjects) // + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + The contents of an EXCLUDE_ROUTE object are a series of variable- + length data items called subobjects. This specification adapts ERO + subobjects as defined in [RFC3209], [RFC3473], and [RFC3477] for use + in route exclusions. The SRLG subobject as defined in Section 2 of + this document has not been defined before. The SRLG subobject is + defined here for use with route exclusions. + + The following subobject types are supported. + + Type Subobject + -------------+------------------------------- + 1 IPv4 prefix + 2 IPv6 prefix + 4 Unnumbered Interface ID + 32 Autonomous system number + 34 SRLG + + The defined values for Type above are specified in [RFC3209] and in + this document. + + The concept of loose or strict hops has no meaning in route + exclusion. The L bit, defined for ERO subobjects in [RFC3209], is + reused here to indicate that an abstract node MUST be excluded (value + + + +Lee, et al. Standards Track [Page 7] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + + 0) or SHOULD be avoided (value 1). The distinction is that the path + of an LSP must not traverse an abstract node listed in the XRO with + the L bit clear, but may traverse one with the L bit set. A node + responsible for routing an LSP (for example, for expanding a loose + hop) should attempt to minimize the number of abstract nodes listed + in the XRO with the L bit set that are traversed by the LSP according + to local policy. A node generating XRO subobjects with the L bit set + must be prepared to accept an LSP that traverses one, some, or all of + the corresponding abstract nodes. + + Subobjects 1, 2, and 4 refer to an interface or a set of interfaces. + An Attribute octet is introduced in these subobjects to indicate the + attribute (e.g., interface, node, SRLG) associated with the + interfaces that should be excluded from the path. For instance, the + attribute node allows a whole node to be excluded from the path by + specifying an interface of that node in the XRO subobject, in + contrast to the attribute interface, which allows a specific + interface (or multiple interfaces) to be excluded from the path + without excluding the whole node. The attribute SRLG allows all + SRLGs associated with an interface to be excluded from the path. + +3.1.1. IPv4 Prefix Subobject + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |L| Type | Length | IPv4 address (4 bytes) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | IPv4 address (continued) | Prefix Length | Attribute | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + L + 0 indicates that the attribute specified MUST be excluded. + 1 indicates that the attribute specified SHOULD be avoided. + + Attribute + + Interface attribute values + 0 indicates that the interface or set of interfaces + associated with the IPv4 prefix should be excluded or + avoided. + + Node attribute value + 1 indicates that the node or set of nodes associated with + the IPv4 prefix should be excluded or avoided. + + + + + + +Lee, et al. Standards Track [Page 8] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + + SRLG attribute values + 2 indicates that all the SRLGs associated with the IPv4 + prefix should be excluded or avoided. + + The rest of the fields are as defined in [RFC3209]. + +3.1.2. IPv6 Prefix Subobject + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |L| Type | Length | IPv6 address (16 bytes) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | IPv6 address (continued) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | IPv6 address (continued) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | IPv6 address (continued) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | IPv6 address (continued) | Prefix Length | Attribute | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + L + 0 indicates that the attribute specified MUST be excluded. + 1 indicates that the attribute specified SHOULD be avoided. + + Attribute + + Interface attribute value + 0 indicates that the interface or set of interfaces + associated with the IPv6 prefix should be excluded or + avoided. + + Node attribute value + 1 indicates that the node or set of nodes associated with + the IPv6 prefix should be excluded or avoided. + + SRLG attribute value + 2 indicates that all the SRLGs associated with the IPv6 + prefix should be excluded or avoided. + + The rest of the fields are as defined in [RFC3209]. + + + + + + + + + +Lee, et al. Standards Track [Page 9] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + +3.1.3. Unnumbered Interface ID Subobject + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |L| Type | Length | Reserved | Attribute | + | | | |(must be zero) | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | TE Router ID | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Interface ID (32 bits) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + L + 0 indicates that the attribute specified MUST be excluded. + 1 indicates that the attribute specified SHOULD be avoided. + + Attribute + + Interface attribute value + 0 indicates that the Interface ID specified should be + excluded or avoided. + + Node attribute value + 1 indicates that the node with the Router ID should be + excluded or avoided (this can be achieved using an IPv4/v6 + subobject as well, but is included here because it may be + convenient to use information from subobjects of an RRO, as + defined in [RFC3477], in specifying the exclusions). + + SRLG attribute value + 2 indicates that all the SRLGs associated with the interface + should be excluded or avoided. + + Reserved + This field is reserved. It SHOULD be set to zero on + transmission and MUST be ignored on receipt. + + The rest of the fields are as defined in [RFC3477]. + +3.1.4. Autonomous System Number Subobject + + The meaning of the L bit is as follows: + 0 indicates that the abstract node specified MUST be excluded. + 1 indicates that the abstract node specified SHOULD be avoided. + + The rest of the fields are as defined in [RFC3209]. There is no + Attribute octet defined. + + + +Lee, et al. Standards Track [Page 10] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + +3.1.5. SRLG Subobject + + The meaning of the L bit is as follows: + 0 indicates that the SRLG specified MUST be excluded + 1 indicates that the SRLG specified SHOULD be avoided + + The Attribute octet is not present. The rest of the fields are as + defined in the "SRLG Subobject" section of this document. + +3.2. Processing Rules for the EXCLUDE_ROUTE Object (XRO) + + The exclude route list is encoded as a series of subobjects contained + in an EXCLUDE_ROUTE object. Each subobject identifies an abstract + node in the exclude route list. + + Each abstract node may be a precisely specified IP address belonging + to a node, or an IP address with prefix identifying interfaces of a + group of nodes, an Autonomous System, or an SRLG. + + The Explicit Route and routing processing is unchanged from the + description in [RFC3209] with the following additions: + + 1. When a Path message is received at a node, the node MUST check + that it is not a member of any of the abstract nodes in the XRO if + it is present in the Path message. If the node is a member of any + of the abstract nodes in the XRO with the L-flag set to "exclude", + it SHOULD return a PathErr with the error code "Routing Problem" + and error value of "Local node in Exclude Route". If there are + SRLGs in the XRO, the node SHOULD check that the resources the + node uses are not part of any SRLG with the L-flag set to + "exclude" that is specified in the XRO. If it is, it SHOULD + return a PathErr with error code "Routing Problem" and error value + of "Local node in Exclude Route". + + 2. Each subobject MUST be consistent. If a subobject is not + consistent then the node SHOULD return a PathErr with error code + "Routing Problem" and error value "Inconsistent Subobject". An + example of an inconsistent subobject is an IPv4 Prefix subobject + containing the IP address of a node and the attribute field is set + to "interface" or "SRLG". + + 3. The subobjects in the ERO and XRO SHOULD NOT contradict each + other. If a Path message is received that contains contradicting + ERO and XRO subobjects, then: + + - Subobjects in the XRO with the L flag not set (zero) MUST take + precedence over the subobjects in the ERO -- that is, a + mandatory exclusion expressed in the XRO MUST be honored and an + + + +Lee, et al. Standards Track [Page 11] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + + implementation MUST reject such a Path message. This means that + a PathErr with error code "Routing Problem" and error value of + "Route blocked by Exclude Route" is returned. + + - Subobjects in the XRO with the L flag set do not take precedence + over ERO subobjects -- that is, an implementation MAY choose to + reject a Path message because of such a contradiction, but MAY + continue and set up the LSP (ignoring the XRO subobjects that + contradict the ERO subobjects). + + 4. When choosing a next hop or expanding an explicit route to include + additional subobjects, a node: + + a. MUST NOT introduce an explicit node or an abstract node that + equals or is a member of any abstract node that is specified in + the EXCLUDE_ROUTE object with the L-flag set to "exclude". The + number of introduced explicit nodes or abstract nodes with the + L flag set to "avoid", which indicates that it is not mandatory + to be excluded but that it is less preferred, SHOULD be + minimized in the computed path. + + b. MUST NOT introduce links, nodes, or resources identified by the + SRLG Id specified in the SRLG subobjects(s). The number of + introduced SRLGs with the L flag set to "avoid" SHOULD be + minimized. + + If these rules preclude further forwarding of the Path message, + the node SHOULD return a PathErr with the error code "Routing + Problem" and error value of "Route blocked by Exclude Route". + + Note that the subobjects in the XRO is an unordered list of + subobjects. + + A node receiving a Path message carrying an XRO MAY reject the + message if the XRO is too large or complicated for the local + implementation or the rules of local policy. In this case, the node + MUST send a PathErr message with the error code "Routing Error" and + error value "XRO Too Complex". An ingress LSR receiving this error + code/value combination MAY reduce the complexity of the XRO or route + around the node that rejected the XRO. + + The XRO Class-Num is of the form 11bbbbbb so that nodes that do not + support the XRO forward it uninspected and do not apply the + extensions to ERO processing described above. This approach is + chosen to allow route exclusion to traverse parts of the network that + are not capable of parsing or handling the new function. Note that + + + + + +Lee, et al. Standards Track [Page 12] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + + Record Route may be used to allow computing nodes to observe + violations of route exclusion and attempt to re-route the LSP + accordingly. + + If a node supports the XRO, but not a particular subobject or part of + that subobject, then that particular subobject is ignored. Examples + of a part of a subobject that can be supported are: (1) only prefix + 32 of the IPv4 prefix subobject could be supported, or (2) a + particular subobject is supported but not the particular attribute + field. + + When a node forwards a Path message, it can do the following three + operations related to XRO besides the processing rules mentioned + above: + + 1. If no XRO was present, an XRO may be included. + + 2. If an XRO was present, it may remove the XRO if it is sure that + the next nodes do not need this information anymore. An example + is where a node can expand the ERO to a full strict path towards + the destination. See Figure 1 where BC2 is removing the XRO from + the Path message. + + 3. If an XRO was present, the content of the XRO can be modified. + Subobjects can be added or removed. See Figure 1 for an example + where AB2 is stripping off some subobjects. + + In any case, a node MUST NOT introduce any explicit or abstract node + in the XRO (irrespective of the value of the L flag) that it also has + introduced in the ERO. + +4. Explicit Exclusion Route + + The Explicit Exclusion Route defines abstract nodes or resources + (such as links, unnumbered interfaces, or labels) that must not or + should not be used on the path between two inclusive abstract nodes + or resources in the explicit route. + +4.1. Explicit Exclusion Route Subobject (EXRS) + + A new ERO subobject type is defined. The Explicit Exclusion Route + Subobject (EXRS) has type 33. Although the EXRS is an ERO subobject + and the XRO is reusing the ERO subobject, an EXRS MUST NOT be present + in an XRO. An EXRS is an ERO subobject that contains one or more + subobjects of its own, called EXRS subobjects. + + + + + + +Lee, et al. Standards Track [Page 13] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + + The format of the EXRS is as follows: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |L| Type | Length | Reserved | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | | + // one or more EXRS subobjects // + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + L + It MUST be set to zero on transmission and MUST be ignored on + receipt. (Note: The L bit in an EXRS subobject is as defined + for the XRO subobjects.) + + Type + The type of the subobject (33). + + Reserved + This field is reserved. It SHOULD be set to zero on + transmission and MUST be ignored on receipt. + + EXRS subobjects + An EXRS subobject indicates the abstract node or resource to be + excluded. The format of an EXRS subobject is exactly the same + as the format of a subobject in the XRO. An EXRS may include + all subobjects defined in this document for the XRO. + + Thus, an EXRS for an IP hop may look as follows: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |L| Type | Length | Reserved | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |L| Type | Length | IPv4 address (4 bytes) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | IPv4 address (continued) | Prefix Length | Attribute | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + + + + + + + + + +Lee, et al. Standards Track [Page 14] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + +4.2. Processing Rules for the Explicit Exclusion Route Subobject (EXRS) + + Each EXRS may carry multiple exclusions. The exclusion is encoded + exactly as for XRO subobjects and prefixed by an additional Type and + Length. + + The scope of the exclusion is the step between the previous ERO + subobject that identifies an abstract node, and the subsequent ERO + subobject that identifies an abstract node. The processing rules of + the EXRS are the same as the processing rule of the XRO within this + scope. Multiple exclusions may be present between any pair of + abstract nodes. + + Exclusions may indicate explicit nodes, abstract nodes, or Autonomous + Systems that must not be traversed on the path to the next abstract + node indicated in the ERO. + + Exclusions may also indicate resources (such as unnumbered + interfaces, link ids, and labels) that must not be used on the path + to the next abstract node indicated in the ERO. + + SRLGs may also be indicated for exclusion from the path to the next + abstract node in the ERO by the inclusion of an EXRS containing an + SRLG subobject. If the L bit in the SRLG subobject is zero, the + resources (nodes, links, etc.) identified by the SRLG MUST NOT be + used on the path to the next abstract node indicated in the ERO. If + the L bit is set, the resources identified by the SRLG SHOULD be + avoided. + + If a node is called upon to process an EXRS and does not support + handling of exclusions it will behave as described in [RFC3209] when + an unrecognized ERO subobject is encountered. This means that this + node will return a PathErr with error code "Routing Error" and error + value "Bad EXPLICIT_ROUTE object" with the EXPLICIT_ROUTE object + included, truncated (on the left) to the offending EXRS. + + If the presence of EXRS precludes further forwarding of the Path + message, the node SHOULD return a PathErr with the error code + "Routing Problem" and error value "Route Blocked by Exclude Route". + + A node MAY reject a Path message if the EXRS is too large or + complicated for the local implementation or as governed by local + policy. In this case, the node MUST send a PathErr message with the + error code "Routing Error" and error value "EXRS Too Complex". An + ingress LSR receiving this error code/value combination MAY reduce + the complexity of the EXRS or route around the node that rejected the + EXRS. + + + + +Lee, et al. Standards Track [Page 15] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + +5. Processing of XRO together with EXRS + + When an LSR performs ERO expansion and finds both the XRO in the Path + message and EXRS in the ERO, it MUST exclude all the SRLGs, nodes, + links, and resources listed in both places. Where some elements + appear in both lists, it MUST be handled according to the stricter + exclusion request. That is, if one list says that an SRLG, node, + link, or resource must be excluded, and the other says only that it + should be avoided, then the element MUST be excluded. + +6. Minimum Compliance + + An implementation MUST be at least compliant with the following: + + 1. The XRO MUST be supported with the following restrictions: + + - The IPv4 Prefix subobject MUST be supported with a prefix length + of 32, and an attribute value of "interface" and "node". Other + prefix values and attribute values MAY be supported. + + - The IPv6 Prefix subobject MUST be supported with a prefix length + of 128, and an attribute value of "interface" and "node". Other + prefix values and attribute values MAY be supported. + + 2. The EXRS MAY be supported. If supported, the same restrictions as + for the XRO apply. If not supported, an EXRS encountered during + normal ERO processing MUST be rejected as an unknown ERO subobject + as described in Section 4.2. Note that a node SHOULD NOT parse + ahead into an ERO, and if it does, it MUST NOT reject the ERO if + it discovers an EXRS that applies to another node. + + 3. If XRO or EXRS are supported, the implementation MUST be compliant + with the processing rules of the supported, not supported, or + partially supported subobjects as specified within this document. + +7. Security Considerations + + Security considerations for MPLS-TE and GMPLS signaling are covered + in [RFC3209] and [RFC3473]. This document does not introduce any new + messages or any substantive new processing, and so those security + considerations continue to apply. + + Note that any security concerns that exist with explicit routes + should be considered with regard to route exclusions. For example, + some administrative boundaries may consider explicit routes to be + security violations and may strip EROs from the Path messages that + they process. In this case, the XRO should also be considered for + removal from the Path message. + + + +Lee, et al. Standards Track [Page 16] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + + It is possible that an arbitrarily complex XRO or EXRS sequence could + be introduced as a form of denial-of-service attack since its + presence will potentially cause additional processing at each node on + the path of the LSP. It should be noted that such an attack assumes + that an otherwise trusted LSR (i.e., one that has been authenticated + by its neighbors) is misbehaving. A node that receives an XRO or + EXRS sequence that it considers too complex according to its local + policy may respond with a PathErr message carrying the error code + "Routing Error" and error value "XRO Too Complex" or "EXRS Too + Complex". + +8. IANA Considerations + + It might be considered that an alternative approach would be to + assign one of the bits of the ERO subobject type field (perhaps the + top bit) to identify that a subobject is intended for inclusion + rather than exclusion. However, [RFC3209] states that the type field + (seven bits) should be assigned as 0 - 63 through IETF consensus + action, 64 - 95 as first come first served, and 96 - 127 are reserved + for private use. It would not be acceptable to disrupt existing + implementations, so the only option would be to split the IETF + consensus range leaving only 32 subobject types. It is felt that 32 + would be an unacceptably small number for future expansion of the + protocol. + +8.1. New ERO Subobject Type + + IANA registry: RSVP PARAMETERS + Subsection: Class Names, Class Numbers, and Class Types + + A new subobject has been added to the existing entry for: + + 20 EXPLICIT_ROUTE + + The registry reads: + + 33 Explicit Exclusion Route subobject (EXRS) + + The Explicit Exclusion Route subobject (EXRS) is defined in Section + 4.1, "Explicit Exclusion Route Subobject (EXRS)". This subobject may + be present in the Explicit Route Object, but not in the Route Record + Object or in the new EXCLUDE_ROUTE object, and it should not be + listed among the subobjects for those objects. + + + + + + + + +Lee, et al. Standards Track [Page 17] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + +8.2. New RSVP-TE Class Numbers + + IANA registry: RSVP PARAMETERS + Subsection: Class Names, Class Numbers, and Class Types + + A new class number has been added for EXCLUDE_ROUTE object (XRO) as + defined in Section 3.1, "EXCLUDE_ROUTE Object (XRO)". + + EXCLUDE_ROUTE + Class-Num of type 11bbbbbb + Value: 232 + Defined CType: 1 (EXCLUDE_ROUTE) + + Subobjects 1, 2, 4, and 32 are as defined for Explicit Route Object. + An additional subobject has been registered as requested in Section + 8.1, "New ERO Subobject Type". The text should appear as: + + Sub-object type + 1 IPv4 address [RFC3209] + 2 IPv6 address [RFC3209] + 4 Unnumbered Interface ID [RFC3477] + 32 Autonomous system number [RFC3209] + 33 Explicit Exclusion Route subobject (EXRS) [RFC4874] + 34 SRLG [RFC4874] + + The SRLG subobject is defined in Section 3.1.5, "SRLG Subobject". + The value 34 has been assigned. + +8.3. New Error Codes + + IANA registry: RSVP PARAMETERS + Subsection: Error Codes and Globally-Defined Error Value Sub-Codes + + New Error Values sub-codes have been registered for the Error Code + 'Routing Problem' (24). + + 64 = Unsupported Exclude Route Subobject Type + 65 = Inconsistent Subobject + 66 = Local Node in Exclude Route + 67 = Route Blocked by Exclude Route + 68 = XRO Too Complex + 69 = EXRS Too Complex + + + + + + + + + +Lee, et al. Standards Track [Page 18] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + +9. Acknowledgments + + This document reuses text from [RFC3209] for the description of + EXCLUDE_ROUTE. + + The authors would like to express their thanks to Lou Berger, Steffen + Brockmann, Igor Bryskin, Dimitri Papadimitriou, Cristel Pelsser, and + Richard Rabbat for their considered opinions on this document. Also + thanks to Yakov Rekhter for reminding us about SRLGs! + + Thanks to Eric Gray for providing GenArt review and to Ross Callon + for his comments. + +10. References + +10.1. Normative References + + [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate + Requirement Levels", BCP 14, RFC 2119, March 1997. + + [RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V., + and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP + Tunnels", RFC 3209, December 2001. + + [RFC3473] Berger, L., "Generalized Multi-Protocol Label Switching + (GMPLS) Signaling Resource ReserVation Protocol-Traffic + Engineering (RSVP-TE) Extensions", RFC 3473, January + 2003. + + [RFC3477] Kompella, K. and Y. Rekhter, "Signalling Unnumbered Links + in Resource ReSerVation Protocol - Traffic Engineering + (RSVP-TE)", RFC 3477, January 2003. + + [RFC4202] Kompella, K. and Y. Rekhter, "Routing Extensions in + Support of Generalized Multi-Protocol Label Switching + (GMPLS)", RFC 4202, October 2005. + +10.2. Informative References + + [CRANKBACK] Farrel, A., Satyanarayana, A., Iwata, A., Ash, G., and S. + Marshall-Unitt, "Crankback Signaling Extensions for MPLS + Signaling", Work in Progress, January 2007. + + [RFC3630] Katz, D., Kompella, K., and D. Yeung, "Traffic + Engineering (TE) Extensions to OSPF Version 2", RFC 3630, + September 2003. + + + + + +Lee, et al. Standards Track [Page 19] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + + [RFC3784] Smit, H. and T. Li, "Intermediate System to Intermediate + System (IS-IS) Extensions for Traffic Engineering (TE)", + RFC 3784, June 2004. + + [RFC3812] Srinivasan, C., Viswanathan, A., and T. Nadeau, + "Multiprotocol Label Switching (MPLS) Traffic Engineering + (TE) Management Information Base (MIB)", RFC 3812, June + 2004. + + [RFC4208] Swallow, G., Drake, J., Ishimatsu, H., and Y. Rekhter, + "Generalized Multiprotocol Label Switching (GMPLS) User- + Network Interface (UNI): Resource ReserVation Protocol- + Traffic Engineering (RSVP-TE) Support for the Overlay + Model", RFC 4208, October 2005. + + [RFC4216] Zhang, R. and JP. Vasseur, "MPLS Inter-Autonomous System + (AS) Traffic Engineering (TE) Requirements", RFC 4216, + November 2005. + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +Lee, et al. Standards Track [Page 20] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + +Appendix A. Applications + + This section describes some applications that can make use of the + XRO. The intention is to show that the XRO is not an application- + specific object, but that it can be used for multiple purposes. In a + few examples, other solutions might be possible for that particular + case, but the intention is to show that a single object can be used + for all the examples, hence making the XRO a rather generic object + without having to define a solution and new objects for each new + application. + +A.1. Inter-Area LSP Protection + + One method to establish an inter-area LSP is where the ingress router + selects an ABR, and then the ingress router computes a path towards + this selected ABR such that the configured constraints of the LSP are + fulfilled. In the example of Figure A.1, an LSP has to be + established from node A in area 1 to node C in area 2. If no loose + hops are configured, then the computed ERO at A could look as + follows: (A1-strict, A2-strict, ABR1-strict, C-loose). When the Path + message arrives at ABR1, then the ERO is (ABR1-strict, C-loose), and + it can be expanded by ABR1 to (B1-strict, ABR3-strict, C-loose). + Similarly, at ABR3 the received ERO is (ABR3-strict, C-loose), and it + can be expanded to (C1-strict, C2-strict, C-strict). If a backup LSP + also has to be established, then A takes another ABR (ABR2 in this + case) and computes a path towards this ABR that fulfills the + constraints of the LSP and that is disjoint from the path of the + primary LSP. The ERO generated by A looks as follows for this + example: (A3-strict, A4-strict, ABR2-strict, C-loose). + + In order to let ABR2 expand the ERO, it also needs to know the path + of the primary LSP so that the ERO expansion is disjoint from the + path of the primary LSP. Therefore, A also includes an XRO that at + least contains (ABR1, B1, ABR3, C1, C2). Based on these constraints, + ABR2 can expand the ERO such that it is disjoint from the primary + LSP. In this example, the ERO computed by ABR2 would be (B2-strict, + ABR4-strict, C-loose), and the XRO generated by B contains at least + (ABR3, C1, C2). The latter information is needed for ABR4 to expand + the ERO so that the path is disjoint from the primary LSP in area 2. + + + + + + + + + + + + +Lee, et al. Standards Track [Page 21] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + + Area 1 Area 0 Area 2 + <---------------><--------------><---------------> + + +---A1---A2----ABR1-----B1-----ABR3----C1---C2---+ + | | | | | + | | | | | + A | | | C + | | | | | + | | | | | + +---A3---A4----ABR2-----B2-----ABR4----C3---C4---+ + + Figure A.1: Inter-area LSPs + + In this example, a node performing the path computation first selects + an ABR and then computes a strict path towards this ABR. For the + backup LSP, all nodes of the primary LSP in the next areas have to be + put in the XRO (with the exception of the destination node if node + protection and no link protection is required). When an ABR computes + the next path segment, i.e., the path over the next area, it may + remove the nodes from the XRO that are located in that area with the + exception of the ABR where the primary LSP is exiting the area. The + latter information is still required because when the selected ABR + (ABR4 in this example) further expands the ERO, it has to exclude the + ABR on which the primary LSP is entering that area (ABR3 in this + example). This means that when ABR2 generates an XRO, it may remove + the nodes in area 0 from the XRO but not ABR3. Note that not doing + this would not cause harm in this example because there is no path + from ABR4 to C via ABR3 in area 2. If there is a link between ABR4- + ABR3 and ABR3-C, then it is required to have ABR3 in the XRO + generated by ABR2. + + Discussion on the length of the XRO: When link or node protection is + requested, the length of the XRO is bounded by the length of the RRO + of the primary LSP. It can be made shorter by removing nodes by the + ingress node and the ABRs. In the example above, the RRO of the + primary LSP contains 8 subobjects, while the maximum XRO length can + be bounded by 6 subobjects (nodes A1 and A2 do not have to be in the + XRO). For SRLG protection, the XRO has to list all SRLGs that are + crossed by the primary LSP. + +A.2. Inter-AS LSP Protection + + When an inter-AS LSP (which has to be protected by a backup LSP to + provide link or node protection) is established, the same method as + for the inter-area LSP case can be used. The difference is when the + backup LSP is not following the same AS-path as the primary LSP + because then the XRO should always contain the full path of the + primary LSP. In case the backup LSP is following the same AS-path + + + +Lee, et al. Standards Track [Page 22] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + + (but with different ASBRs -- at least in case of node protection), it + is similar to the inter-area case: ASBRs expanding the ERO over the + next AS may remove the XRO subobjects located in that AS. Note that + this can only be done by an ingress ASBR (the ASBR where the LSP is + entering the AS). + + Discussion on the length of the XRO: the XRO is bounded by the length + of the RRO of the primary LSP. + + Suppose that SRLG protection is required, and the ASs crossed by the + main LSP use a consistent way of allocating SRLG-ids to the links + (i.e., the ASs use a single SRLG space). In this case, the SRLG-ids + of each link used by the main LSP can be recorded by means of the + RRO; the SRLG-ids are then used by the XRO. If the SRLG-ids are only + meaningful when local to the AS, putting SRLG-ids in the XRO crossing + many ASs makes no sense. To provide SRLG protection for inter-AS + LSPs the link IP address of the inter-AS link used by the primary LSP + can be put into the XRO of the Path message of the detour LSP or + bypass tunnel. The ASBR where the detour LSP or bypass tunnel is + entering the AS can translate this into the list of SRLG-ids known to + the local AS. + + Discussion on the length of the XRO: the XRO only contains 1 + subobject, which contains the IP address of the inter-AS link + traversed by the primary LSP (assuming that the primary LSP and + detour LSP or bypass tunnel are leaving the AS in the same area, and + that they are also entering the next AS in the same area). + + + + + + + + + + + + + + + + + + + + + + + + +Lee, et al. Standards Track [Page 23] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + +A.3. Protection in the GMPLS Overlay Model + + When an edge-node wants to establish an LSP towards another edge-node + over an optical core network as described in [RFC4208] (see Figure + A.2), the XRO can be used for multiple purposes. + + Overlay Overlay + Network +--------------------------------+ Network + +----------+ | | +----------+ + | +----+ | | +-----+ +-----+ +-----+ | | +----+ | + | | | | | | | | | | | | | | | | + | --+ EN1+-+-----+--+ CN1 +---+ CN2 +---+ CN3 +---+-----+-+ EN3+-- | + | | | | +--+--+ | | | | +---+--+ | | | | + | +----+ | | | +--+--+ +--+--+ +--+--+ | | | +----+ | + | | | | | | | | | | | + +----------+ | | | | | | | +----------+ + | | | | | | | + +----------+ | | | | | | | +----------+ + | | | | +--+--+ | +--+--+ | | | | + | +----+ | | | | | +------+ | | | | +----+ | + | | +-+--+ | | CN4 +-------------+ CN5 | | +--+-+ | | + | --+ EN2+-+-----+--+ | | +---+-----+-+ EN4+-- | + | | | | | +-----+ +-----+ | | | | | + | +----+ | | | | +----+ | + | | +--------------------------------+ | | + +----------+ Core Network +----------+ + + Overlay Overlay + Network Network + + Legend: + EN - Edge-Node + CN - Core-Node + + Figure A.2 + + A first application is where an edge-node wants to establish multiple + LSPs towards the same destination edge-node, and these LSPs need to + have few or no SRLGs in common. In this case EN1 could establish an + LSP towards EN3, and then it can establish a second LSP listing all + links used by the first LSP with the indication to avoid the SRLGs of + these links. This information can be used by CN1 to compute a path + for the second LSP. If the core network consists of multiple areas, + then the SRLG-ids have to be listed in the XRO. The same example + applies to nodes and links. + + + + + + +Lee, et al. Standards Track [Page 24] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + + Another application is where the edge-node wants to set up a backup + LSP that is also protecting the links between the edge-nodes and + core-nodes. For instance, when EN2 establishes an LSP to EN4, it + sends a Path message to CN4, which computes a path towards EN4 over + (for instance) CN5. When EN2 gets back the RRO of that LSP, it can + signal a new LSP to CN1 with EN4 as the destination and the XRO + computed based on the RRO of the first LSP. Based on this + information, CN1 can compute a path that has the requested diversity + properties (e.g., a path going over CN2 and CN3, and then to EN4). + + It is clear that in these examples, the core-node may not alter the + RRO in a Resv message to make its only contents be the subobjects + from the egress core-node through the egress edge-node. + +A.4. LSP Protection inside a Single Area + + The XRO can also be used inside a single area. Take for instance a + network where the TE extensions of the IGPs as described in [RFC3630] + and [RFC3784] are not used. Hence, each node has to select a next- + hop and possibly crankback [CRANKBACK] has to be used when there is + no viable next-hop. In this case, when signaling a backup LSP, the + XRO can be put in the Path message to exclude the links, nodes, or + SRLGs of the primary LSP. An alternative way to provide this + functionality would be to indicate the following in the Path message + of the backup LSP: the primary LSP and which type of protection is + required. This latter solution would work for link and node + protection, but not for SRLG protection. + + When link or node protection is requested, the XRO is of the same + length as the RRO of the primary LSP. For SRLG protection, the XRO + has to list all SRLGs that are crossed by the primary LSP. Note that + for SRLG protection, the link IP address to reference the SRLGs of + that link cannot be used since the TE extensions of the IGPs are not + used in this example. Hence, a node cannot translate any link IP + address located in that area to its SRLGs. + + + + + + + + + + + + + + + + +Lee, et al. Standards Track [Page 25] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + +Authors' Addresses + + Cheng-Yin Lee + EMail: c.yin.lee@gmail.com + + + Adrian Farrel + Old Dog Consulting + Phone: +44 (0) 1978 860944 + EMail: adrian@olddog.co.uk + + + Stefaan De Cnodder + Alcatel-Lucent + Copernicuslaan 50 + B-2018 Antwerp + Belgium + Phone: +32 3 240 85 15 + EMail: stefaan.de_cnodder@alcatel-lucent.be + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +Lee, et al. Standards Track [Page 26] + +RFC 4874 Exclude Routes - Extension to RSVP-TE April 2007 + + +Full Copyright Statement + + Copyright (C) The IETF Trust (2007). + + This document is subject to the rights, licenses and restrictions + contained in BCP 78, and except as set forth therein, the authors + retain all their rights. + + This document and the information contained herein are provided on an + "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS + OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND + THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS + OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF + THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED + WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. + +Intellectual Property + + The IETF takes no position regarding the validity or scope of any + Intellectual Property Rights or other rights that might be claimed to + pertain to the implementation or use of the technology described in + this document or the extent to which any license under such rights + might or might not be available; nor does it represent that it has + made any independent effort to identify any such rights. Information + on the procedures with respect to rights in RFC documents can be + found in BCP 78 and BCP 79. + + Copies of IPR disclosures made to the IETF Secretariat and any + assurances of licenses to be made available, or the result of an + attempt made to obtain a general license or permission for the use of + such proprietary rights by implementers or users of this + specification can be obtained from the IETF on-line IPR repository at + http://www.ietf.org/ipr. + + The IETF invites any interested party to bring to its attention any + copyrights, patents or patent applications, or other proprietary + rights that may cover technology that may be required to implement + this standard. Please address the information to the IETF at + ietf-ipr@ietf.org. + +Acknowledgement + + Funding for the RFC Editor function is currently provided by the + Internet Society. + + + + + + + +Lee, et al. Standards Track [Page 27] + -- cgit v1.2.3