From 4bfd864f10b68b71482b35c818559068ef8d5797 Mon Sep 17 00:00:00 2001 From: Thomas Voss Date: Wed, 27 Nov 2024 20:54:24 +0100 Subject: doc: Add RFC documents --- doc/rfc/rfc6850.txt | 3307 +++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 3307 insertions(+) create mode 100644 doc/rfc/rfc6850.txt (limited to 'doc/rfc/rfc6850.txt') diff --git a/doc/rfc/rfc6850.txt b/doc/rfc/rfc6850.txt new file mode 100644 index 0000000..9161e00 --- /dev/null +++ b/doc/rfc/rfc6850.txt @@ -0,0 +1,3307 @@ + + + + + + +Internet Engineering Task Force (IETF) A. Rijhsinghani +Request for Comments: 6850 Hewlett-Packard +Category: Standards Track K. Zebrose +ISSN: 2070-1721 HW Embedded + January 2013 + + + Definitions of Managed Objects for Routing Bridges (RBridges) + +Abstract + + This memo defines a portion of the Management Information Base (MIB) + for use with network management protocols. In particular, it defines + objects for managing a Routing Bridge (RBridge), also known as a + TRILL Switch, based on the IETF TRILL (Transparent Interconnection of + Lots of Links) protocol. + +Status of This Memo + + This is an Internet Standards Track document. + + This document is a product of the Internet Engineering Task Force + (IETF). It represents the consensus of the IETF community. It has + received public review and has been approved for publication by the + Internet Engineering Steering Group (IESG). Further information on + Internet Standards is available in Section 2 of RFC 5741. + + Information about the current status of this document, any errata, + and how to provide feedback on it may be obtained at + http://www.rfc-editor.org/info/rfc6850. + +Copyright Notice + + Copyright (c) 2013 IETF Trust and the persons identified as the + document authors. All rights reserved. + + This document is subject to BCP 78 and the IETF Trust's Legal + Provisions Relating to IETF Documents + (http://trustee.ietf.org/license-info) in effect on the date of + publication of this document. Please review these documents + carefully, as they describe your rights and restrictions with respect + to this document. Code Components extracted from this document must + include Simplified BSD License text as described in Section 4.e of + the Trust Legal Provisions and are provided without warranty as + described in the Simplified BSD License. + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 1] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + +Table of Contents + + 1. Introduction ....................................................2 + 2. The Internet-Standard Management Framework ......................3 + 3. Overview ........................................................3 + 4. Conventions .....................................................4 + 5. Structure of the MIB Module .....................................4 + 5.1. Textual Conventions ........................................4 + 5.2. The rbridgeBase Subtree ....................................4 + 5.3. The rbridgeFdb Subtree .....................................4 + 5.4. The rbridgeVlan Subtree ....................................4 + 5.5. The rbridgeEsadi Subtree ...................................4 + 5.6. The rbridgeCounters Subtree ................................4 + 5.7. The rbridgeSnooping Subtree ................................5 + 5.8. The rbridgeDtree Subtree ...................................5 + 5.9. The rbridgeTrill Subtree ...................................5 + 5.10. The Notifications Subtree .................................5 + 6. Relationship to Other MIB Modules ...............................5 + 6.1. Relationship to IF-MIB .....................................5 + 6.2. Relationship to BRIDGE-MIB .................................6 + 6.3. Relationship to P-BRIDGE-MIB ...............................6 + 6.4. Relationship to Q-BRIDGE-MIB ...............................6 + 6.5. Relationship to IEEE8021-BRIDGE-MIB ........................7 + 6.6. Relationship to IEEE8021-Q-BRIDGE-MIB ......................7 + 6.7. Relationship to ISIS-MIB ...................................8 + 6.8. MIB Modules Required for IMPORTS ...........................8 + 7. Definition of the RBridge MIB Module ............................9 + 8. Security Considerations ........................................55 + 9. IANA Considerations ............................................56 + 10. Contributors ..................................................56 + 11. References ....................................................57 + 11.1. Normative References .....................................57 + 11.2. Informative References ...................................58 + +1. Introduction + + This document describes a model for managing Routing Bridges + (RBridges), also known as TRILL Switches, as defined in [RFC6325]. + RBridges provide optimal pair-wise forwarding without configuration + using IS-IS routing and encapsulation of traffic. RBridges are + compatible with previous IEEE 802.1 customer bridges as well as IPv4 + and IPv6 routers and end nodes. They are as invisible to current IP + routers as bridges are and, like routers, they terminate the bridge + spanning tree protocol. In creating an RBridge management model, the + device is viewed primarily as a customer bridge. For a discussion of + the problem addressed by TRILL (Transparent Interconnection of Lots + of Links), see [RFC5556]. + + + + +Rijhsinghani & Zebrose Standards Track [Page 2] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + RBridges support features specified for transparent bridges in + IEEE 802.1, and the corresponding MIB modules are used to manage + those features. For IS-IS purposes, the corresponding MIB module is + used to manage the protocol. This MIB module specifies those objects + that are TRILL-specific and hence not available in other MIB modules. + +2. The Internet-Standard Management Framework + + For a detailed overview of the documents that describe the current + Internet-Standard Management Framework, please refer to section 7 of + RFC 3410 [RFC3410]. + + Managed objects are accessed via a virtual information store, termed + the Management Information Base or MIB. MIB objects are generally + accessed through the Simple Network Management Protocol (SNMP). + Objects in the MIB are defined using the mechanisms defined in the + Structure of Management Information (SMI). This memo specifies a MIB + module that is compliant to the SMIv2, which is described in STD 58, + RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 + [RFC2580]. + +3. Overview + + The RBridge MIB module is intended as an overall framework for + managing RBridges, also known as TRILL Switches. Where possible, the + MIB references existing MIB definitions in order to maximize reuse. + This results in a considerable emphasis on the relationship with + other MIB modules. + + Starting with the physical interfaces, there are requirements for + certain elements of the IF-MIB to be implemented. These elements are + required in order to connect the per-port parameters to higher-level + functions of the physical device. + + Transparent bridging, VLANs, traffic classes, and multicast filtering + are supported by the TRILL protocol, and the corresponding management + is expected to conform to the BRIDGE-MIB module [RFC4188] and to the + P-BRIDGE-MIB and Q-BRIDGE-MIB modules [RFC4363]. + + The IS-IS routing protocol is used in order to determine the optimum + pair-wise forwarding path. This protocol is managed using the IS-IS + MIB module defined in [RFC4444]. Since the TRILL protocol specifies + the use of a single level and a fixed area address of zero, some + IS-IS MIB objects are not applicable. Some IS-IS MIB objects are + used in the TRILL protocol. + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 3] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + +4. Conventions + + The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", + "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and + "OPTIONAL" in this document are to be interpreted as described in + RFC 2119 [RFC2119]. + +5. Structure of the MIB Module + + Objects in this MIB module are arranged into subtrees. Each subtree + is organized as a set of related objects. The various subtrees are + shown below. These are supplemented with required elements of the + IF-MIB, ISIS-MIB, BRIDGE-MIB, P-BRIDGE-MIB, Q-BRIDGE-MIB, and IEEE + Bridge MIB modules. + +5.1. Textual Conventions + + Textual conventions are defined to represent object types relevant to + TRILL. + +5.2. The rbridgeBase Subtree + + This subtree contains system- and port-specific objects applicable to + all RBridges. + +5.3. The rbridgeFdb Subtree + + This subtree contains objects applicable to the forwarding database + used by the RBridge in making packet-forwarding decisions. Because + it contains additional information used by the TRILL protocol not + applicable to 802.1D/Q bridges, it is a superset of the corresponding + subtrees defined in the BRIDGE-MIB and Q-BRIDGE-MIB. + +5.4. The rbridgeVlan Subtree + + This subtree describes objects applicable to VLANs configured on the + RBridge. + +5.5. The rbridgeEsadi Subtree + + This subtree describes objects relevant to RBridges that support the + optional End-Station Address Distribution Information (ESADI) + protocol. + +5.6. The rbridgeCounters Subtree + + This subtree contains statistics maintained by RBridges that can aid + in monitoring and troubleshooting networks connected by them. + + + +Rijhsinghani & Zebrose Standards Track [Page 4] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + +5.7. The rbridgeSnooping Subtree + + This subtree describes objects applicable to RBridges capable of + snooping IPv4 and/or IPv6 multicast control frames and pruning IP + multicast traffic based on detection of IP multicast routers and + listeners. + +5.8. The rbridgeDtree Subtree + + This subtree contains objects relevant to distribution trees computed + by RBridges for the forwarding of multi-destination frames. + +5.9. The rbridgeTrill Subtree + + This subtree contains objects applicable to the TRILL IS-IS protocol, + beyond what is available in the ISIS-MIB. + +5.10. The Notifications Subtree + + The defined notifications are focused on the TRILL protocol + functionality. Notifications are defined for changes in the + Designated RBridge status and the topology. + +6. Relationship to Other MIB Modules + + The IF-MIB, BRIDGE-MIB, P-BRIDGE-MIB, Q-BRIDGE-MIB, + IEEE8021-BRIDGE-MIB, IEEE8021-Q-BRIDGE-MIB, and ISIS-MIB modules all + contain objects relevant to the RBridge MIB. Management objects + contained in these modules are not duplicated here, to reduce overlap + to the extent possible. + + The Bridge MIB modules were originally written in the IETF and + implemented by many vendors. Per [RFC4663], this has recently been + transferred to the IEEE 802.1 working group. As vendors may have + implemented either the IETF or IEEE Bridge MIB modules, this RBridge + MIB module is designed to work with either one. + +6.1. Relationship to IF-MIB + + The port identification elements MUST be implemented in order to + allow them to be cross-referenced. The Interfaces MIB [RFC2863] + requires that any MIB module that is an adjunct of the Interfaces MIB + clarify specific areas within the Interfaces MIB module. These areas + were intentionally left vague in the Interfaces MIB module to avoid + over-constraining the MIB, thereby precluding management of certain + media types. Section 4 of [RFC2863] enumerates several areas that a + + + + + +Rijhsinghani & Zebrose Standards Track [Page 5] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + media-specific MIB module must clarify. The implementor is referred + to [RFC2863] in order to understand the general intent of these + areas. + +6.2. Relationship to BRIDGE-MIB + + The following subtrees in the BRIDGE-MIB [RFC4188] contain + information relevant to RBridges when the corresponding functionality + is implemented. + + o dot1dBase + + o dot1dTp + + o dot1dStatic + +6.3. Relationship to P-BRIDGE-MIB + + The following subtrees in the P-BRIDGE-MIB [RFC4363] contain + information relevant to RBridges when the corresponding functionality + is implemented. + + o dot1dExtBase + + o dot1dPriority + + o dot1dGarp + + o dot1dGmrp + + o dot1dTpHCPortTable + + o dot1dTpPortOverflowTable + +6.4. Relationship to Q-BRIDGE-MIB + + The following groups in the Q-BRIDGE-MIB [RFC4363] contain + information relevant to RBridges when the corresponding functionality + is implemented. This functionality is also contained in the + IEEE8021-Q-BRIDGE-MIB. + + o dot1qBase + + o dot1qTp + + o dot1qStatic + + + + + +Rijhsinghani & Zebrose Standards Track [Page 6] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + o dot1qVlan + + o dot1vProtocol + +6.5. Relationship to IEEE8021-BRIDGE-MIB + + The following subtrees in the IEEE8021-BRIDGE-MIB contain information + relevant to RBridges when the corresponding functionality is + implemented. + + o ieee8021BridgeBase + + o ieee8021BridgeTp + + o ieee8021BridgePriority + + o ieee8021BridgeMrp + + o ieee8021BridgeMmrp + + o ieee8021BridgeInternalLan + + o ieee8021BridgeDot1d + +6.6. Relationship to IEEE8021-Q-BRIDGE-MIB + + The following subtrees in the IEEE8021-Q-BRIDGE-MIB contain + information relevant to RBridges when the corresponding functionality + is implemented. + + o ieee8021QBridgeBase + + o ieee8021QBridgeTp + + o ieee8021QBridgeStatic + + o ieee8021QBridgeVlan + + o ieee8021QBridgeProtocol + + + + + + + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 7] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + +6.7. Relationship to ISIS-MIB + + "Management Information Base for Intermediate System to Intermediate + System (IS-IS)" [RFC4444] defines a MIB module for the IS-IS routing + protocol when it is used to construct routing tables for IP networks. + While most of these objects are applicable to the TRILL layer 2 + implementation, note the IS-IS constraints for the current version of + TRILL [RFC6325]: + + o The TRILL IS-IS instance uses a single Level 1 IS-IS area. + + o The TRILL Level 1 IS-IS area uses the fixed area address zero. + + o The TRILL IS-IS instance is not used for IP address advertisement. + + o The TRILL IS-IS instance is used for only a single protocol: + TRILL. + + Accordingly, tables that report IP address reachability and tables + that allow configuration or reporting of multiple IS-IS areas, + multiple IS-IS levels, or multiple protocols will be empty in the + ISIS-MIB module for the current version of TRILL. + + Note also that when more than one instance of the IS-IS protocol is + running on a device, as in the case of a device performing both + RBridge and IS-IS IP router functions, multiple instances of the + ISIS-MIB module can be distinguished by the use of SNMPv3 contexts or + SNMPv1 communities. + +6.8. MIB Modules Required for IMPORTS + + The following MIB module imports objects from the SNMPv2-SMI + [RFC2578], SNMPv2-TC [RFC2579], SNMPv2-CONF [RFC2580], IF-MIB + [RFC2863], INET-ADDRESS-MIB [RFC4001], BRIDGE-MIB [RFC4188], + and Q-BRIDGE-MIB [RFC4363]. (The IEEE Bridge MIB modules import + similar TCs.) + + + + + + + + + + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 8] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + +7. Definition of the RBridge MIB Module + + RBRIDGE-MIB DEFINITIONS ::= BEGIN + + -- ---------------------------------------------------------- -- + -- MIB for RBRIDGE devices, also known as TRILL Switches + -- ---------------------------------------------------------- -- + IMPORTS + MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, + Counter32, Counter64, Unsigned32, mib-2 + FROM SNMPv2-SMI -- RFC2578 + TEXTUAL-CONVENTION, TruthValue, MacAddress, RowStatus + FROM SNMPv2-TC -- RFC2579 + MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP + FROM SNMPv2-CONF -- RFC2580 + VlanId, PortList + FROM Q-BRIDGE-MIB -- RFC4363 + InetAddress, InetAddressType + FROM INET-ADDRESS-MIB -- RFC4001 + BridgeId + FROM BRIDGE-MIB -- RFC4188 + InterfaceIndex + FROM IF-MIB -- RFC2863 + ; + + rbridgeMIB MODULE-IDENTITY + LAST-UPDATED "201301070000Z" + ORGANIZATION "IETF TRILL Working Group" + CONTACT-INFO + "http://datatracker.ietf.org/wg/trill/charter/ + Email: trill@ietf.org + + Anil Rijhsinghani + Hewlett-Packard + Tel: +1 508 323 1251 + Email: anil@charter.net + + Kate Zebrose + HW Embedded + Tel: +1 617 840 9673 + Email: zebrose@alum.mit.edu" + + DESCRIPTION + "The RBridge MIB module for managing switches that support + the TRILL protocol." + + REVISION "201301070000Z" + + + + +Rijhsinghani & Zebrose Standards Track [Page 9] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + DESCRIPTION + "Initial version, published as RFC 6850. + + Copyright (c) 2013 IETF Trust and the persons identified as + authors of the code. All rights reserved. + + Redistribution and use in source and binary forms, with or + without modification, is permitted pursuant to, and subject to + the license terms contained in, the Simplified BSD License set + forth in Section 4.c of the IETF Trust's Legal Provisions + Relating to IETF Documents + (http://trustee.ietf.org/license-info)." + + ::= { mib-2 214 } + + + -- ---------------------------------------------------------- -- + -- Subtrees in the RBridge MIB + -- ---------------------------------------------------------- -- + + rbridgeNotifications OBJECT IDENTIFIER ::= { rbridgeMIB 0 } + rbridgeObjects OBJECT IDENTIFIER ::= { rbridgeMIB 1 } + rbridgeConformance OBJECT IDENTIFIER ::= { rbridgeMIB 2 } + + rbridgeBase OBJECT IDENTIFIER ::= { rbridgeObjects 1 } + rbridgeFdb OBJECT IDENTIFIER ::= { rbridgeObjects 2 } + rbridgeVlan OBJECT IDENTIFIER ::= { rbridgeObjects 3 } + rbridgeEsadi OBJECT IDENTIFIER ::= { rbridgeObjects 4 } + rbridgeCounter OBJECT IDENTIFIER ::= { rbridgeObjects 5 } + rbridgeSnooping OBJECT IDENTIFIER ::= { rbridgeObjects 6 } + rbridgeDtree OBJECT IDENTIFIER ::= { rbridgeObjects 7 } + rbridgeTrill OBJECT IDENTIFIER ::= { rbridgeObjects 8 } + + -- ---------------------------------------------------------- -- + -- Type Definitions + -- ---------------------------------------------------------- -- + + RbridgeAddress ::= TEXTUAL-CONVENTION + DISPLAY-HINT "1x:" + STATUS current + DESCRIPTION + "The Media Access Control (MAC) address used by an RBridge + port. This may match the RBridge IS-IS SystemID." + SYNTAX OCTET STRING (SIZE (6)) + + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 10] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + RbridgeNickname ::= TEXTUAL-CONVENTION + DISPLAY-HINT "d" + STATUS current + DESCRIPTION + "The 16-bit identifier used in TRILL as an + abbreviation for the RBridge's 48-bit IS-IS System ID. + The value 0 means a nickname is not specified, the values + 0xFFC0 through 0xFFFE are reserved for future allocation, + and the value 0xFFFF is permanently reserved." + REFERENCE + "RFC 6325, Section 3.7" + SYNTAX Unsigned32 (0..65471) + + -- + -- the rbridgeBase subtree + -- + -- Implementation of the rbridgeBase subtree is mandatory for all + -- RBridges. + -- + + rbridgeBaseTrillVersion OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The maximum TRILL version number that this RBridge + supports." + REFERENCE + "RFC 6325, Section 3.2" + ::= { rbridgeBase 1 } + + rbridgeBaseNumPorts OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "ports" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of ports controlled by this RBridge." + REFERENCE + "RFC 6325, Section 2.6.1" + ::= { rbridgeBase 2 } + + rbridgeBaseForwardDelay OBJECT-TYPE + SYNTAX Unsigned32 (4..30) + UNITS "seconds" + MAX-ACCESS read-write + STATUS current + + + + +Rijhsinghani & Zebrose Standards Track [Page 11] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + DESCRIPTION + "Modified aging time for address entries after an appointed + forwarder change. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.8.3" + ::= { rbridgeBase 3 } + + rbridgeBaseUniMultipathEnable OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The enabled status of unicast TRILL multipathing. + It is enabled when true. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Appendix C" + ::= { rbridgeBase 4 } + + rbridgeBaseMultiMultipathEnable OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The enabled status of multi-destination TRILL multipathing. + It is enabled when true. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Appendix C" + ::= { rbridgeBase 5 } + + rbridgeBaseAcceptEncapNonadj OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Accept TRILL-encapsulated frames from a neighbor with which + this RBridge does not have an IS-IS adjacency, when the value + of this object is 'true'. + + + + + +Rijhsinghani & Zebrose Standards Track [Page 12] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.6.2" + ::= { rbridgeBase 6 } + + rbridgeBaseNicknameNumber OBJECT-TYPE + SYNTAX Unsigned32 (1..256) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The number of nicknames this RBridge should acquire. + These can be acquired dynamically or configured + statically. This value represents the maximum + number of entries in rbridgeBaseNicknameTable. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 3.7.3" + ::= { rbridgeBase 7 } + + -- ---------------------------------------------------------- -- + -- The RBridge Base Nickname Table + -- ---------------------------------------------------------- -- + + rbridgeBaseNicknameTable OBJECT-TYPE + SYNTAX SEQUENCE OF RbridgeBaseNicknameEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains information about nicknames + configured by an operator or learned dynamically + by this RBridge." + REFERENCE + "RFC 6325, Section 3.7" + ::= { rbridgeBase 8 } + + rbridgeBaseNicknameEntry OBJECT-TYPE + SYNTAX RbridgeBaseNicknameEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A list of information for each nickname of the RBridge." + REFERENCE + "RFC 6325, Section 3.7" + INDEX { rbridgeBaseNicknameName } + ::= { rbridgeBaseNicknameTable 1 } + + + +Rijhsinghani & Zebrose Standards Track [Page 13] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + RbridgeBaseNicknameEntry ::= + SEQUENCE { + rbridgeBaseNicknameName + RbridgeNickname, + rbridgeBaseNicknamePriority + Unsigned32, + rbridgeBaseNicknameDtrPriority + Unsigned32, + rbridgeBaseNicknameType + INTEGER, + rbridgeBaseNicknameRowStatus + RowStatus + } + + rbridgeBaseNicknameName OBJECT-TYPE + SYNTAX RbridgeNickname + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Nicknames are 16-bit quantities that act as + abbreviations for RBridge's 48-bit IS-IS System ID to + achieve a more compact encoding." + REFERENCE + "RFC 6325, Section 3.7" + ::= { rbridgeBaseNicknameEntry 1 } + + rbridgeBaseNicknamePriority OBJECT-TYPE + SYNTAX Unsigned32 (0..255) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This RBridge's priority to hold this nickname. When + the nickname is configured, the default value of this + object is 192. When the nickname is configured, the most + significant bit (0x80) must be set and the bottom 7 bits + have the default value of 0x40, so 0x80 + 0x40 == 0xC0, + which is 192 decimal. Additionally, the bottom 7 bits + could be configured to a value other than 0x40. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 3.7" + DEFVAL { 192 } + ::= { rbridgeBaseNicknameEntry 2 } + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 14] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + rbridgeBaseNicknameDtrPriority OBJECT-TYPE + SYNTAX Unsigned32 (1..65535) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The distribution tree root priority for this nickname. + The default value of this object is 32768. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.5" + DEFVAL { 32768 } + ::= { rbridgeBaseNicknameEntry 3 } + + rbridgeBaseNicknameType OBJECT-TYPE + SYNTAX INTEGER { + static(1), + dynamic(2) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This object indicates the status of the entry. The + default value is static(1). + static(1) - this entry has been configured and + will remain after the next reset of the RBridge. + dynamic(2) - this entry has been acquired by the + RBridge nickname acquisition protocol." + REFERENCE + "RFC 6325, Section 3.7" + DEFVAL { static } + ::= { rbridgeBaseNicknameEntry 4 } + + rbridgeBaseNicknameRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object indicates the status of the entry." + ::= { rbridgeBaseNicknameEntry 5 } + + + + + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 15] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + -- ---------------------------------------------------------- -- + -- The RBridge Port Table + -- ---------------------------------------------------------- -- + + rbridgeBasePortTable OBJECT-TYPE + SYNTAX SEQUENCE OF RbridgeBasePortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains generic information about every + port that is associated with this RBridge." + REFERENCE + "RFC 6325, Section 5.3" + ::= { rbridgeBase 9 } + + rbridgeBasePortEntry OBJECT-TYPE + SYNTAX RbridgeBasePortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A list of information for each port of the bridge." + REFERENCE + "RFC 6325, Section 5.3" + INDEX { rbridgeBasePort } + ::= { rbridgeBasePortTable 1 } + + RbridgeBasePortEntry ::= + SEQUENCE { + rbridgeBasePort + Unsigned32, + rbridgeBasePortIfIndex + InterfaceIndex, + rbridgeBasePortDisable + TruthValue, + rbridgeBasePortTrunkPort + TruthValue, + rbridgeBasePortAccessPort + TruthValue, + rbridgeBasePortP2pHellos + TruthValue, + rbridgeBasePortState + INTEGER, + rbridgeBasePortInhibitionTime + Unsigned32, + rbridgeBasePortDisableLearning + TruthValue, + rbridgeBasePortDesiredDesigVlan + VlanId, + + + +Rijhsinghani & Zebrose Standards Track [Page 16] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + rbridgeBasePortDesigVlan + VlanId, + rbridgeBasePortStpRoot + BridgeId, + rbridgeBasePortStpRootChanges + Counter32, + rbridgeBasePortStpWiringCloset + BridgeId + } + + rbridgeBasePort OBJECT-TYPE + SYNTAX Unsigned32 (1..65535) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The port number of the port for which this entry + contains RBridge management information." + REFERENCE + "RFC 6325, Section 5.3" + ::= { rbridgeBasePortEntry 1 } + + rbridgeBasePortIfIndex OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of the instance of the ifIndex object, + defined in the IF-MIB, for the interface corresponding + to this port. The RBridge port sits on top of + this interface." + ::= { rbridgeBasePortEntry 2 } + + rbridgeBasePortDisable OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Disable port bit. When this bit is set (true), all frames + received or to be transmitted are discarded, with the + possible exception of some layer 2 control frames that may + be generated and transmitted or received and processed + locally. Default value is 'false'. + + The value of this object MUST be retained across + re-initializations of the management system." + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 17] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + REFERENCE + "RFC 6325, Section 4.9.1" + DEFVAL { false } + ::= { rbridgeBasePortEntry 3 } + + rbridgeBasePortTrunkPort OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "End-station service disable (trunk port) bit. When this bit + is set (true), all native frames received on the port and all + native frames that would have been sent on the port are + discarded. Default value is 'false'. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.9.1" + DEFVAL { false } + ::= { rbridgeBasePortEntry 4 } + + rbridgeBasePortAccessPort OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "TRILL traffic disable (access port) bit. If this bit is + set, the goal is to avoid sending any TRILL frames, except + TRILL-Hello frames, on the port, since it is intended only + for native end-station traffic. This ensures that the link + is not on the shortest path for any destination. Default + value is 'false'. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.9.1" + DEFVAL { false } + ::= { rbridgeBasePortEntry 5 } + + rbridgeBasePortP2pHellos OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Use point-to-point (P2P) Hellos bit. If this bit is set, + Hellos sent on this port are IS-IS P2P Hellos, not the + + + +Rijhsinghani & Zebrose Standards Track [Page 18] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + default TRILL-Hellos. In addition, the IS-IS P2P three-way + handshake is used on P2P RBridge links. Default value is + 'false'. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.9.1" + DEFVAL { false } + ::= { rbridgeBasePortEntry 6 } + + rbridgeBasePortState OBJECT-TYPE + SYNTAX INTEGER { + uninhibited(1), + portInhibited(2), + vlanInhibited(3), + disabled(4), + broken(5) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The port's current state. If the entire port is + inhibited, its state is portInhibited(2). If specific VLANs + are inhibited, the state is vlanInhibited(3), and + rbridgeVlanPortTable will tell which VLANs are inhibited. + For ports that are disabled (see rbridgeBasePortDisable), + this object will have a value of disabled(4). If the + RBridge has detected a port that is malfunctioning, it will + place that port into the broken(5) state." + REFERENCE + "RFC 6325, Section 4.2.4.3" + ::= { rbridgeBasePortEntry 7 } + + rbridgeBasePortInhibitionTime OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "seconds" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Time in seconds that this RBridge will inhibit forwarding + on this port after it observes a spanning tree root bridge + change on a link or receives conflicting VLAN forwarder + information. The default value is 30. + + The value of this object MUST be retained across + re-initializations of the management system." + + + + +Rijhsinghani & Zebrose Standards Track [Page 19] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + REFERENCE + "RFC 6325, Section 4.2.4.3" + DEFVAL { 30 } + ::= { rbridgeBasePortEntry 8 } + + rbridgeBasePortDisableLearning OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Disable learning of MAC addresses seen on this port. + To disable learning, the value of this object must be + set to 'true'. The default is 'false'. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.8" + DEFVAL { false } + ::= { rbridgeBasePortEntry 9 } + + rbridgeBasePortDesiredDesigVlan OBJECT-TYPE + SYNTAX VlanId + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The VLAN that a Designated RBridge (DRB) will specify in + its TRILL-Hellos as the VLAN to be used by all RBridges on + the link for TRILL frames. This VLAN must be enabled on + this port. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.4.3" + ::= { rbridgeBasePortEntry 10 } + + rbridgeBasePortDesigVlan OBJECT-TYPE + SYNTAX VlanId + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The VLAN being used on this link for TRILL frames." + REFERENCE + "RFC 6325, Section 4.4.3" + ::= { rbridgeBasePortEntry 11 } + + + + + +Rijhsinghani & Zebrose Standards Track [Page 20] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + rbridgeBasePortStpRoot OBJECT-TYPE + SYNTAX BridgeId + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The bridge identifier of the root of the spanning tree, + as learned from a Bridge PDU (BPDU) received on this port. + For the Multiple Spanning Tree Protocol (MSTP), this is + the root bridge of the Common and Internal Spanning Tree + (CIST). If no BPDU has been heard, the value returned + is a string of zeros." + REFERENCE + "RFC 6325, Section 4.2.4.3" + ::= { rbridgeBasePortEntry 12 } + + rbridgeBasePortStpRootChanges OBJECT-TYPE + SYNTAX Counter32 + UNITS "changes" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of times a change in the root bridge is seen from + spanning tree BPDUs received on this port, indicating a + change in bridged LAN topology. Each such change may cause + the port to be inhibited for a period of time. This counter + should be synchronized with ifCounterDiscontinuityTime. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system." + REFERENCE + "RFC 6325, Section 4.9.3.2" + ::= { rbridgeBasePortEntry 13 } + + rbridgeBasePortStpWiringCloset OBJECT-TYPE + SYNTAX BridgeId + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The Bridge ID to be used as the spanning tree root in BPDUs + sent for the Wiring Closet topology solution described in + [RFC6325]. Note that the same value of this object must be + set on all RBridge ports participating in this solution. + The default value is all 0s. A non-zero value configured + into this object indicates that this solution is in use. + + The value of this object MUST be retained across + re-initializations of the management system." + + + + +Rijhsinghani & Zebrose Standards Track [Page 21] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + REFERENCE + "RFC 6325, Appendix A.3.3" + ::= { rbridgeBasePortEntry 14 } + + -- ------------------------------------------------------------- + -- RBridge Forwarding Database + -- ------------------------------------------------------------- + + rbridgeConfidenceNative OBJECT-TYPE + SYNTAX Unsigned32 (0..255) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The confidence level associated with MAC addresses + learned from native frames. This is applicable to + all RBridge ports. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.8.1" + ::= { rbridgeFdb 1 } + + rbridgeConfidenceDecap OBJECT-TYPE + SYNTAX Unsigned32 (0..255) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The confidence level associated with inner MAC addresses + learned after decapsulation of a TRILL data frame. + This is applicable to all RBridge ports. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.8.1" + ::= { rbridgeFdb 2 } + + rbridgeConfidenceStatic OBJECT-TYPE + SYNTAX Unsigned32 (0..255) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The confidence level associated with MAC addresses that + are statically configured. The default value is 255. + + The value of this object MUST be retained across + re-initializations of the management system." + + + +Rijhsinghani & Zebrose Standards Track [Page 22] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + REFERENCE + "RFC 6325, Section 4.8.2" + DEFVAL { 255 } + ::= { rbridgeFdb 3 } + + + -- ------------------------------------------------------------- + -- Multiple Forwarding Databases for RBridges + -- + -- This allows for an instance per FdbId, as defined in the + -- Bridge MIB. + -- + -- Each VLAN may have an independent FDB, or multiple VLANs may + -- share one. + -- ------------------------------------------------------------- + + rbridgeUniFdbTable OBJECT-TYPE + SYNTAX SEQUENCE OF RbridgeUniFdbEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains information about unicast entries + for which the device has forwarding and/or filtering + information. This information is used by the + transparent bridging function in determining how to + propagate a received frame." + REFERENCE + "RFC 6325, Section 4.8" + ::= { rbridgeFdb 4 } + + rbridgeUniFdbEntry OBJECT-TYPE + SYNTAX RbridgeUniFdbEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information about a specific unicast MAC address for + which the RBridge has some forwarding and/or filtering + information." + INDEX { rbridgeFdbId, rbridgeUniFdbAddr } + ::= { rbridgeUniFdbTable 1 } + + RbridgeUniFdbEntry ::= + SEQUENCE { + rbridgeFdbId + Unsigned32, + rbridgeUniFdbAddr + MacAddress, + + + + +Rijhsinghani & Zebrose Standards Track [Page 23] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + rbridgeUniFdbPort + Unsigned32, + rbridgeUniFdbNickname + RbridgeNickname, + rbridgeUniFdbConfidence + Unsigned32, + rbridgeUniFdbStatus + INTEGER + } + + rbridgeFdbId OBJECT-TYPE + SYNTAX Unsigned32 (0..4294967295) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The identity of this Filtering Database." + ::= { rbridgeUniFdbEntry 1 } + + rbridgeUniFdbAddr OBJECT-TYPE + SYNTAX MacAddress + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A unicast MAC address for which the device has + forwarding information." + ::= { rbridgeUniFdbEntry 2 } + + rbridgeUniFdbPort OBJECT-TYPE + SYNTAX Unsigned32 (0..65535) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Either the value '0', or the RBridge port number of the + port on which a frame having a source address equal to the + value of the corresponding instance of rbridgeUniFdbAddr + has been seen. A value of '0' indicates that the port + number has not been learned but that the device does have + some information about this MAC address. + + Implementors are encouraged to assign the port value to + this object whenever it is available, even for addresses + for which the corresponding value of rbridgeUniFdbStatus is + not learned(3)." + ::= { rbridgeUniFdbEntry 3 } + + rbridgeUniFdbNickname OBJECT-TYPE + SYNTAX RbridgeNickname + MAX-ACCESS read-only + + + +Rijhsinghani & Zebrose Standards Track [Page 24] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + STATUS current + DESCRIPTION + "The RBridge nickname that is placed in the egress + nickname field of a TRILL frame sent to this + rbridgeFdbAddress in this rbridgeFdbId." + REFERENCE + "RFC 6325, Section 4.8.1" + ::= { rbridgeUniFdbEntry 4 } + + rbridgeUniFdbConfidence OBJECT-TYPE + SYNTAX Unsigned32 (0..255) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The confidence level associated with this entry." + REFERENCE + "RFC 6325, Section 4.8.1" + ::= { rbridgeUniFdbEntry 5 } + + rbridgeUniFdbStatus OBJECT-TYPE + SYNTAX INTEGER { + other(1), + invalid(2), + learned(3), + self(4), + mgmt(5), + esadi(6) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The status of this entry. The meanings of the values + are: + other(1) - none of the following. + invalid(2) - this entry is no longer valid (e.g., it + was learned but has since aged out) but has not + yet been flushed from the table. + learned(3) - the information in this entry was learned + and is being used. + self(4) - the value of the corresponding instance of + rbridgeFdbAddress represents one of the device's + addresses. The corresponding instance of + rbridgeFdbPort indicates which of the device's + ports has this address. + + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 25] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + mgmt(5) - the value of the corresponding instance of + rbridgeFdbAddress was configured by management. + esadi(6) - the value of the corresponding instance of + rbridgeFdbAddress was learned from ESADI." + ::= { rbridgeUniFdbEntry 6 } + + -- ------------------------------------------------------------- + -- RBridge Forwarding Information Base (FIB) + -- ------------------------------------------------------------- + + rbridgeUniFibTable OBJECT-TYPE + SYNTAX SEQUENCE OF RbridgeUniFibEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains information about nicknames known by + the RBridge. If Equal-Cost Multipath (ECMP) is implemented, + there are as many entries for a nickname as there are ECMP + paths available for it." + ::= { rbridgeFdb 5 } + + rbridgeUniFibEntry OBJECT-TYPE + SYNTAX RbridgeUniFibEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A list of information about nicknames known by the RBridge. + If ECMP is implemented, there are as many entries as there + are ECMP paths available for a given nickname." + INDEX { rbridgeUniFibNickname, rbridgeUniFibPort, + rbridgeUniFibNextHop } + ::= { rbridgeUniFibTable 1 } + + RbridgeUniFibEntry ::= + SEQUENCE { + rbridgeUniFibNickname + RbridgeNickname, + rbridgeUniFibPort + Unsigned32, + rbridgeUniFibNextHop + RbridgeNickname, + rbridgeUniFibHopCount + Unsigned32 + } + + rbridgeUniFibNickname OBJECT-TYPE + SYNTAX RbridgeNickname + MAX-ACCESS not-accessible + + + +Rijhsinghani & Zebrose Standards Track [Page 26] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + STATUS current + DESCRIPTION + "An RBridge nickname for which this RBridge has + forwarding information." + ::= { rbridgeUniFibEntry 1 } + + rbridgeUniFibPort OBJECT-TYPE + SYNTAX Unsigned32 (0..65535) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The RBridge port number of the port attached to the + next-hop RBridge for the path towards the RBridge whose + nickname is specified in this entry." + ::= { rbridgeUniFibEntry 2 } + + rbridgeUniFibNextHop OBJECT-TYPE + SYNTAX RbridgeNickname + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The nickname of the next-hop RBridge for the path + towards the RBridge whose nickname is specified in this + entry." + ::= { rbridgeUniFibEntry 3 } + + rbridgeUniFibHopCount OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The hop count from this ingress RBridge to the egress + RBridge whose nickname is specified in + rbridgeUniFibNickname." + ::= { rbridgeUniFibEntry 4 } + + rbridgeMultiFibTable OBJECT-TYPE + SYNTAX SEQUENCE OF RbridgeMultiFibEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains information about egress nicknames + used for multi-destination frame forwarding by this + RBridge." + ::= { rbridgeFdb 6 } + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 27] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + rbridgeMultiFibEntry OBJECT-TYPE + SYNTAX RbridgeMultiFibEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A list of information about egress nicknames used for + multi-destination frame forwarding by this RBridge." + INDEX { rbridgeMultiFibNickname } + ::= { rbridgeMultiFibTable 1 } + + RbridgeMultiFibEntry ::= + SEQUENCE { + rbridgeMultiFibNickname + RbridgeNickname, + rbridgeMultiFibPorts + PortList + } + + rbridgeMultiFibNickname OBJECT-TYPE + SYNTAX RbridgeNickname + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The nickname of the multicast distribution tree." + ::= { rbridgeMultiFibEntry 1 } + + rbridgeMultiFibPorts OBJECT-TYPE + SYNTAX PortList + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The list of ports to which a frame destined to this + multicast distribution tree is flooded. This may be pruned + further based on other forwarding information." + ::= { rbridgeMultiFibEntry 2 } + + + + + + + + + + + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 28] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + -- ---------------------------------------------------------- -- + -- The RBridge VLAN Table + -- ---------------------------------------------------------- -- + + rbridgeVlanTable OBJECT-TYPE + SYNTAX SEQUENCE OF RbridgeVlanEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains information about VLANs on the + RBridge." + ::= { rbridgeVlan 1 } + + rbridgeVlanEntry OBJECT-TYPE + SYNTAX RbridgeVlanEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A list of information about VLANs on the RBridge." + INDEX { rbridgeVlanIndex } + ::= { rbridgeVlanTable 1 } + + RbridgeVlanEntry ::= + SEQUENCE { + rbridgeVlanIndex + Unsigned32, + rbridgeVlanForwarderLosts + Counter32, + rbridgeVlanDisableLearning + TruthValue, + rbridgeVlanSnooping + INTEGER + } + + rbridgeVlanIndex OBJECT-TYPE + SYNTAX Unsigned32 (1..4094|4096..4294967295) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The VLAN-ID referring to this VLAN." + ::= { rbridgeVlanEntry 1 } + + rbridgeVlanForwarderLosts OBJECT-TYPE + SYNTAX Counter32 + UNITS "times" + MAX-ACCESS read-only + STATUS current + + + + +Rijhsinghani & Zebrose Standards Track [Page 29] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + DESCRIPTION + "The number of times this RBridge has lost appointed + forwarder status for this VLAN on any of its ports. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system." + REFERENCE + "RFC 6325, Section 4.8.3" + ::= { rbridgeVlanEntry 2 } + + rbridgeVlanDisableLearning OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Disable learning of MAC addresses seen in this VLAN. + One application of this may be to restrict learning to + ESADI. To disable learning, the value of this object + should be set to 'true'. The default is 'false'. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.8" + DEFVAL { false } + ::= { rbridgeVlanEntry 3 } + + rbridgeVlanSnooping OBJECT-TYPE + SYNTAX INTEGER { + notSupported(1), + ipv4(2), + ipv6(3), + ipv4v6(4) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "IP Multicast Snooping on this VLAN. For RBridges + performing both IPv4 and IPv6 IP Multicast Snooping, the + value returned is ipv4v6(4)." + REFERENCE + "RFC 6325, Section 4.7" + ::= { rbridgeVlanEntry 4 } + + + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 30] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + -- ---------------------------------------------------------- -- + -- The RBridge VLAN Port Table + -- ---------------------------------------------------------- -- + + rbridgeVlanPortTable OBJECT-TYPE + SYNTAX SEQUENCE OF RbridgeVlanPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains information about VLANs on an RBridge + port." + ::= { rbridgeVlan 2 } + + rbridgeVlanPortEntry OBJECT-TYPE + SYNTAX RbridgeVlanPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A list of information about VLANs on the RBridge port." + INDEX { rbridgeBasePort, rbridgeVlanIndex } + ::= { rbridgeVlanPortTable 1 } + + RbridgeVlanPortEntry ::= + SEQUENCE { + rbridgeVlanPortInhibited + TruthValue, + rbridgeVlanPortForwarder + TruthValue, + rbridgeVlanPortAnnouncing + TruthValue, + rbridgeVlanPortDetectedVlanMapping + TruthValue + } + + rbridgeVlanPortInhibited OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This VLAN has been inhibited by the RBridge due to + conflicting forwarder information received from another + RBridge, when the value of this object is 'true'." + REFERENCE + "RFC 6325, Section 4.2.4.3" + ::= { rbridgeVlanPortEntry 1 } + + rbridgeVlanPortForwarder OBJECT-TYPE + SYNTAX TruthValue + + + +Rijhsinghani & Zebrose Standards Track [Page 31] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This RBridge is an appointed forwarder for this VLAN + on this port, when the value of this object is 'true'." + REFERENCE + "RFC 6325, Section 4.2.4.3" + ::= { rbridgeVlanPortEntry 2 } + + rbridgeVlanPortAnnouncing OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "TRILL-Hellos tagged with this VLAN can be sent by this + RBridge on this port, when the value of this object + is 'true'. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.4.3" + DEFVAL { true } + ::= { rbridgeVlanPortEntry 3 } + + rbridgeVlanPortDetectedVlanMapping OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "VLAN mapping has been detected on the link attached + to this port, when the value of this object is 'true'." + REFERENCE + "RFC 6325, Section 4.4.5" + ::= { rbridgeVlanPortEntry 4 } + + + -- ---------------------------------------------------------- -- + -- The RBridge Port Counter Table + -- + -- These counters supplement counters in the Bridge MIB. + -- + -- For example, total frames received by a bridge port and total + -- frames transmitted by a bridge port are reported in the + -- Port In Frames and Port Out Frames counters of the Bridge MIB. + -- These total bridge frame counters include native as well as + -- encapsulated frames. + -- + + + +Rijhsinghani & Zebrose Standards Track [Page 32] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + -- As another example, frames discarded due to excessive frame + -- size are reported in the port counter MTU Exceeded Discards + -- in the Bridge MIB. + -- ---------------------------------------------------------- -- + + rbridgePortCounterTable OBJECT-TYPE + SYNTAX SEQUENCE OF RbridgePortCounterEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains per-port counters for this RBridge." + ::= { rbridgeCounter 1 } + + rbridgePortCounterEntry OBJECT-TYPE + SYNTAX RbridgePortCounterEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Counters for a port on this RBridge." + INDEX { rbridgeBasePort } + ::= { rbridgePortCounterTable 1 } + + RbridgePortCounterEntry ::= + SEQUENCE { + rbridgePortRpfCheckFails + Counter32, + rbridgePortHopCountExceeds + Counter32, + rbridgePortOptionDrops + Counter32, + rbridgePortTrillInFrames + Counter64, + rbridgePortTrillOutFrames + Counter64 + } + + rbridgePortRpfCheckFails OBJECT-TYPE + SYNTAX Counter32 + UNITS "frames" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of times a multi-destination frame was + dropped on this port because the Reverse Path Forwarding + (RPF) check failed. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + + + +Rijhsinghani & Zebrose Standards Track [Page 33] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + other times as indicated by the value of the + ifCounterDiscontinuityTime object of the associated + interface." + REFERENCE + "RFC 6325, Section 4.5.2" + ::= { rbridgePortCounterEntry 1 } + + rbridgePortHopCountExceeds OBJECT-TYPE + SYNTAX Counter32 + UNITS "frames" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of times a frame was dropped on this port + because its hop count was zero. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of the + ifCounterDiscontinuityTime object of the associated + interface." + REFERENCE + "RFC 6325, Section 3.6" + ::= { rbridgePortCounterEntry 2 } + + rbridgePortOptionDrops OBJECT-TYPE + SYNTAX Counter32 + UNITS "frames" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of times a frame was dropped on this port + because it contained unsupported options. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of the + ifCounterDiscontinuityTime object of the associated + interface." + REFERENCE + "RFC 6325, Section 3.5" + ::= { rbridgePortCounterEntry 3 } + + rbridgePortTrillInFrames OBJECT-TYPE + SYNTAX Counter64 + UNITS "frames" + MAX-ACCESS read-only + STATUS current + + + +Rijhsinghani & Zebrose Standards Track [Page 34] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + DESCRIPTION + "The number of TRILL-encapsulated frames that have been + received by this port from its attached link, including + management frames. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of the + ifCounterDiscontinuityTime object of the associated + interface." + REFERENCE + "RFC 6325, Section 2.3" + ::= { rbridgePortCounterEntry 4 } + + rbridgePortTrillOutFrames OBJECT-TYPE + SYNTAX Counter64 + UNITS "frames" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of TRILL-encapsulated frames that have been + transmitted by this port to its attached link, including + management frames. + + Discontinuities in the value of this counter can occur + at re-initialization of the management system, and at + other times as indicated by the value of the + ifCounterDiscontinuityTime object of the associated + interface." + REFERENCE + "RFC 6325, Section 2.3" + ::= { rbridgePortCounterEntry 5 } + + -- ---------------------------------------------------------- -- + -- The RBridge VLAN ESADI Table + -- ---------------------------------------------------------- -- + + rbridgeEsadiTable OBJECT-TYPE + SYNTAX SEQUENCE OF RbridgeEsadiEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table that contains information about ESADI instances on + VLANs, if available." + REFERENCE + "RFC 6325, Section 4.2.5" + ::= { rbridgeEsadi 1 } + + + + +Rijhsinghani & Zebrose Standards Track [Page 35] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + rbridgeEsadiEntry OBJECT-TYPE + SYNTAX RbridgeEsadiEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information about an ESADI instance on a VLAN." + INDEX { rbridgeVlanIndex } + ::= { rbridgeEsadiTable 1 } + + RbridgeEsadiEntry ::= + SEQUENCE { + rbridgeEsadiEnable + TruthValue, + rbridgeEsadiConfidence + Unsigned32, + rbridgeEsadiDrbPriority + Unsigned32, + rbridgeEsadiDrb + RbridgeAddress, + rbridgeEsadiDrbHoldingTime + Unsigned32, + rbridgeEsadiRowStatus + RowStatus + } + + rbridgeEsadiEnable OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "If the RBridge is participating in an ESADI instance for + this VLAN, the value of this object is 'true'. To disable + participation, set it to 'false'. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.2.5" + DEFVAL { true } + ::= { rbridgeEsadiEntry 1 } + + rbridgeEsadiConfidence OBJECT-TYPE + SYNTAX Unsigned32 (0..255) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Confidence level of address entries sent by this + ESADI instance. The default is 16. + + + +Rijhsinghani & Zebrose Standards Track [Page 36] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.2.5" + DEFVAL { 16 } + ::= { rbridgeEsadiEntry 2 } + + rbridgeEsadiDrbPriority OBJECT-TYPE + SYNTAX Unsigned32 (0..127) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The priority of this RBridge for being selected as the + DRB for this ESADI instance. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.2.5" + ::= { rbridgeEsadiEntry 3 } + + rbridgeEsadiDrb OBJECT-TYPE + SYNTAX RbridgeAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The DRB on this ESADI instance's virtual link." + REFERENCE + "RFC 6325, Section 4.2.5" + ::= { rbridgeEsadiEntry 4 } + + rbridgeEsadiDrbHoldingTime OBJECT-TYPE + SYNTAX Unsigned32 (0..127) + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The holding time for this ESADI instance. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.2.5" + ::= { rbridgeEsadiEntry 5 } + + rbridgeEsadiRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + + + +Rijhsinghani & Zebrose Standards Track [Page 37] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + DESCRIPTION + "This object indicates the status of the entry." + ::= { rbridgeEsadiEntry 6 } + + + -- ---------------------------------------------------------- -- + -- The RBridge IP Multicast Snooping Port Table + -- ---------------------------------------------------------- -- + + rbridgeSnoopingPortTable OBJECT-TYPE + SYNTAX SEQUENCE OF RbridgeSnoopingPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "For RBridges implementing IP Multicast Snooping, + information about ports on which the presence of IPv4 + or IPv6 multicast routers has been detected." + REFERENCE + "RFC 6325, Section 4.7" + ::= { rbridgeSnooping 1 } + + rbridgeSnoopingPortEntry OBJECT-TYPE + SYNTAX RbridgeSnoopingPortEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information about ports on which the presence of IPv4 + or IPv6 multicast routers has been detected for a + VLAN." + INDEX { rbridgeBasePort, rbridgeVlanIndex } + ::= { rbridgeSnoopingPortTable 1 } + + RbridgeSnoopingPortEntry ::= + SEQUENCE { + rbridgeSnoopingPortAddrType + INTEGER + } + + rbridgeSnoopingPortAddrType OBJECT-TYPE + SYNTAX INTEGER { + ipv4(1), + ipv6(2), + ipv4v6(3) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The IP address type of an IP multicast router detected + + + +Rijhsinghani & Zebrose Standards Track [Page 38] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + on this port and VLAN. If only IPv4 router(s) + are detected, the value returned is 'ipv4'. If only + IPv6 routers are detected, the value returned is + 'ipv6'. If both IPv4 and IPv6 routers are detected on + this port and VLAN, the value returned is 'ipv4v6'." + REFERENCE + "RFC 6325, Section 4.7" + ::= { rbridgeSnoopingPortEntry 1 } + + -- ---------------------------------------------------------- -- + -- The RBridge IP Multicast Snooping Address Table + -- ---------------------------------------------------------- -- + + rbridgeSnoopingAddrTable OBJECT-TYPE + SYNTAX SEQUENCE OF RbridgeSnoopingAddrEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "For RBridges implementing IP Multicast Snooping, + information about IP multicast addresses being + snooped." + REFERENCE + "RFC 6325, Section 4.8" + ::= { rbridgeSnooping 2 } + + rbridgeSnoopingAddrEntry OBJECT-TYPE + SYNTAX RbridgeSnoopingAddrEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information about IP multicast addresses being + snooped." + INDEX { rbridgeVlanIndex, rbridgeSnoopingAddrType, + rbridgeSnoopingAddr } + ::= { rbridgeSnoopingAddrTable 1 } + + RbridgeSnoopingAddrEntry ::= + SEQUENCE { + rbridgeSnoopingAddrType + InetAddressType, + rbridgeSnoopingAddr + InetAddress, + rbridgeSnoopingAddrPorts + PortList + } + + rbridgeSnoopingAddrType OBJECT-TYPE + SYNTAX InetAddressType + + + +Rijhsinghani & Zebrose Standards Track [Page 39] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The IP multicast address type for which a listener has been + detected by this RBridge. This MIB requires support for only + IPv4 and IPv6 address types." + REFERENCE + "RFC 6325, Section 4.7" + ::= { rbridgeSnoopingAddrEntry 1 } + + rbridgeSnoopingAddr OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The IP multicast address for which a listener has been + detected by this RBridge. The address type of this object + is specified in rbridgeSnoopingAddrType. This MIB requires + support for only global IPv4 and IPv6 addresses, so the + length of the object can be either 4 or 16 bytes. Hence, + the index will not exceed the OID size limit." + REFERENCE + "RFC 6325, Section 4.7" + ::= { rbridgeSnoopingAddrEntry 2 } + + rbridgeSnoopingAddrPorts OBJECT-TYPE + SYNTAX PortList + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The set of ports on which a listener has been detected + for this IP multicast address." + REFERENCE + "RFC 6325, Section 4.7" + ::= { rbridgeSnoopingAddrEntry 3 } + + + -- ---------------------------------------------------------- -- + -- Distribution Trees + -- ---------------------------------------------------------- -- + + rbridgeDtreePriority OBJECT-TYPE + + SYNTAX Unsigned32 (1..65535) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The distribution tree root priority for this RBridge. + + + +Rijhsinghani & Zebrose Standards Track [Page 40] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + The default value of this object is 32768. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.5" + ::= { rbridgeDtree 1 } + + rbridgeDtreeActiveTrees OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of trees being computed by all RBridges + in the campus." + REFERENCE + "RFC 6325, Section 4.5" + ::= { rbridgeDtree 2 } + + rbridgeDtreeMaxTrees OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The maximum number of trees this RBridge can compute." + REFERENCE + "RFC 6325, Section 4.5" + ::= { rbridgeDtree 3 } + + rbridgeDtreeDesiredUseTrees OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The maximum number of trees this RBridge would like to + use for transmission of ingress multi-destination frames." + REFERENCE + "RFC 6325, Section 4.5" + ::= { rbridgeDtree 4 } + + rbridgeDtreeTable OBJECT-TYPE + SYNTAX SEQUENCE OF RbridgeDtreeEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information about distribution trees being computed + by this RBridge." + + + + +Rijhsinghani & Zebrose Standards Track [Page 41] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + REFERENCE + "RFC 6325, Section 4.5" + ::= { rbridgeDtree 5 } + + rbridgeDtreeEntry OBJECT-TYPE + SYNTAX RbridgeDtreeEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "List of information about distribution trees being computed + by this RBridge." + INDEX { rbridgeDtreeNumber } + ::= { rbridgeDtreeTable 1 } + + RbridgeDtreeEntry ::= + SEQUENCE { + rbridgeDtreeNumber + Unsigned32, + rbridgeDtreeNickname + RbridgeNickname, + rbridgeDtreeIngress + TruthValue + } + + rbridgeDtreeNumber OBJECT-TYPE + SYNTAX Unsigned32 (0..65535) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The tree number of a distribution tree being computed by + this RBridge." + REFERENCE + "RFC 6325, Section 4.5" + ::= { rbridgeDtreeEntry 1 } + + rbridgeDtreeNickname OBJECT-TYPE + SYNTAX RbridgeNickname + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The nickname of the distribution tree." + REFERENCE + "RFC 6325, Section 4.5" + ::= { rbridgeDtreeEntry 2 } + + rbridgeDtreeIngress OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + + + +Rijhsinghani & Zebrose Standards Track [Page 42] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + STATUS current + DESCRIPTION + "Indicates whether this RBridge might choose this + distribution tree to ingress a multi-destination frame." + REFERENCE + "RFC 6325, Section 4.5" + ::= { rbridgeDtreeEntry 3 } + + + -- ---------------------------------------------------------- -- + -- TRILL Neighbor List + -- ---------------------------------------------------------- -- + + rbridgeTrillMinMtuDesired OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The desired minimum acceptable inter-RBridge link MTU for + the campus, that is, originatingLSPBufferSize. + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.3" + ::= { rbridgeTrill 1 } + + rbridgeTrillSz OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The minimum acceptable inter-RBridge link size for the + campus for the proper operation of TRILL IS-IS." + REFERENCE + "RFC 6325, Section 4.3" + ::= { rbridgeTrill 2 } + + rbridgeTrillMaxMtuProbes OBJECT-TYPE + SYNTAX Unsigned32 (1..255) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The number of failed MTU-probes before the RBridge + concludes that a particular MTU is not supported by + a neighbor. + + + + + +Rijhsinghani & Zebrose Standards Track [Page 43] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + The value of this object MUST be retained across + re-initializations of the management system." + REFERENCE + "RFC 6325, Section 4.3" + ::= { rbridgeTrill 3 } + + rbridgeTrillNbrTable OBJECT-TYPE + SYNTAX SEQUENCE OF RbridgeTrillNbrEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information about this RBridge's TRILL neighbors." + REFERENCE + "RFC 6325, Section 4.4.2.1" + ::= { rbridgeTrill 4 } + + rbridgeTrillNbrEntry OBJECT-TYPE + SYNTAX RbridgeTrillNbrEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "List of information about this RBridge's TRILL neighbors." + INDEX { rbridgeTrillNbrMacAddr } + ::= { rbridgeTrillNbrTable 1 } + + RbridgeTrillNbrEntry ::= + SEQUENCE { + rbridgeTrillNbrMacAddr + MacAddress, + rbridgeTrillNbrMtu + Unsigned32, + rbridgeTrillNbrFailedMtuTest + TruthValue + } + + rbridgeTrillNbrMacAddr OBJECT-TYPE + SYNTAX MacAddress + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The MAC address of a neighbor of this RBridge." + REFERENCE + "RFC 6325, Section 4.4.2.1" + ::= { rbridgeTrillNbrEntry 1 } + + rbridgeTrillNbrMtu OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + + + +Rijhsinghani & Zebrose Standards Track [Page 44] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + STATUS current + DESCRIPTION + "MTU size for this neighbor for IS-IS communication + purposes." + REFERENCE + "RFC 6325, Section 4.3.2" + ::= { rbridgeTrillNbrEntry 2 } + + rbridgeTrillNbrFailedMtuTest OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "If true, indicates that the neighbor's tested MTU is less + than the minimum acceptable inter-bridge link MTU for the + campus (1470)." + REFERENCE + "RFC 6325, Section 4.3.1" + ::= { rbridgeTrillNbrEntry 3 } + + + -- ---------------------------------------------------------- -- + -- Notifications for use by RBridges + -- ---------------------------------------------------------- -- + + rbridgeBaseNewDrb NOTIFICATION-TYPE + -- OBJECTS { } + STATUS current + DESCRIPTION + "The rbridgeBaseNewDrb notification indicates that the + sending agent has become the new Designated RBridge; the + notification is sent by an RBridge soon after its election + as the new DRB root, e.g., upon expiration of the Topology + Change Timer, immediately subsequent to its election." + ::= { rbridgeNotifications 1 } + + rbridgeBaseTopologyChange NOTIFICATION-TYPE + -- OBJECTS { } + STATUS current + DESCRIPTION + "The rbridgeBaseTopologyChange notification is sent by an + RBridge when any of its configured ports transition to/from + the VLAN-x designated forwarder. The notification is not + sent if an rbridgeBaseNewDrb notification is sent for the + same transition." + ::= { rbridgeNotifications 2 } + + + + + +Rijhsinghani & Zebrose Standards Track [Page 45] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + -- Compliance and Group sections + + rbridgeCompliances OBJECT IDENTIFIER ::= { rbridgeConformance 1 } + + rbridgeGroup OBJECT IDENTIFIER ::= { rbridgeConformance 2 } + + + -- ---------------------------------------------------------- -- + -- Units of Conformance + -- ---------------------------------------------------------- -- + + rbridgeBaseGroup OBJECT-GROUP + OBJECTS { + rbridgeBaseTrillVersion, + rbridgeBaseNumPorts, + rbridgeBaseForwardDelay, + rbridgeBaseUniMultipathEnable, + rbridgeBaseMultiMultipathEnable, + rbridgeBaseAcceptEncapNonadj, + rbridgeBaseNicknameNumber + } + STATUS current + DESCRIPTION + "A collection of objects providing basic control + and status information for the RBridge." + ::= { rbridgeGroup 1 } + + rbridgeBaseNicknameGroup OBJECT-GROUP + OBJECTS { + rbridgeBaseNicknamePriority, + rbridgeBaseNicknameDtrPriority, + rbridgeBaseNicknameType, + rbridgeBaseNicknameRowStatus + } + STATUS current + DESCRIPTION + "A collection of objects providing basic control + and status information for RBridge nicknames." + ::= { rbridgeGroup 2 } + + rbridgeBasePortGroup OBJECT-GROUP + OBJECTS { + rbridgeBasePortIfIndex, + rbridgeBasePortDisable, + rbridgeBasePortTrunkPort, + rbridgeBasePortAccessPort, + rbridgeBasePortP2pHellos, + rbridgeBasePortState, + + + +Rijhsinghani & Zebrose Standards Track [Page 46] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + rbridgeBasePortDesiredDesigVlan, + rbridgeBasePortDesigVlan, + rbridgeBasePortInhibitionTime, + rbridgeBasePortDisableLearning, + rbridgeBasePortStpRoot, + rbridgeBasePortStpRootChanges, + rbridgeBasePortStpWiringCloset + } + STATUS current + DESCRIPTION + "A collection of objects providing basic control + and status information for RBridge ports." + ::= { rbridgeGroup 3 } + + rbridgeFdbGroup OBJECT-GROUP + OBJECTS { + rbridgeConfidenceNative, + rbridgeConfidenceDecap, + rbridgeConfidenceStatic, + rbridgeUniFdbPort, + rbridgeUniFdbNickname, + rbridgeUniFdbConfidence, + rbridgeUniFdbStatus + } + STATUS current + DESCRIPTION + "A collection of objects providing information + about the Unicast Address Database." + ::= { rbridgeGroup 4 } + + rbridgeFibGroup OBJECT-GROUP + OBJECTS { + rbridgeUniFibHopCount, + rbridgeMultiFibPorts + } + STATUS current + DESCRIPTION + "A collection of objects providing information + about the Unicast and Multicast FIBs." + ::= { rbridgeGroup 5 } + + rbridgeVlanGroup OBJECT-GROUP + OBJECTS { + rbridgeVlanForwarderLosts, + rbridgeVlanDisableLearning, + rbridgeVlanSnooping, + rbridgeVlanPortInhibited, + rbridgeVlanPortForwarder, + + + +Rijhsinghani & Zebrose Standards Track [Page 47] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + rbridgeVlanPortAnnouncing, + rbridgeVlanPortDetectedVlanMapping + } + STATUS current + DESCRIPTION + "A collection of objects providing information + about VLANs on the RBridge." + ::= { rbridgeGroup 6 } + + rbridgePortCounterGroup OBJECT-GROUP + OBJECTS { + rbridgePortRpfCheckFails, + rbridgePortHopCountExceeds, + rbridgePortOptionDrops, + rbridgePortTrillInFrames, + rbridgePortTrillOutFrames + } + STATUS current + DESCRIPTION + "A collection of objects providing per-port + counters for the RBridge." + ::= { rbridgeGroup 7 } + + rbridgeEsadiGroup OBJECT-GROUP + OBJECTS { + rbridgeEsadiEnable, + rbridgeEsadiConfidence, + rbridgeEsadiDrbPriority, + rbridgeEsadiDrb, + rbridgeEsadiDrbHoldingTime, + rbridgeEsadiRowStatus + } + STATUS current + DESCRIPTION + "A collection of objects providing information + about ESADI instances on the RBridge." + ::= { rbridgeGroup 8 } + + rbridgeSnoopingGroup OBJECT-GROUP + OBJECTS { + rbridgeSnoopingPortAddrType, + rbridgeSnoopingAddrPorts + } + STATUS current + DESCRIPTION + "A collection of objects providing information about + IP Multicast Snooping. This MIB requires support for + only global IPv4 and IPv6 address types in + + + +Rijhsinghani & Zebrose Standards Track [Page 48] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + rbridgeSnoopingPortAddrType and rbridgeSnoopingAddrType, + so the length of rbridgeSnoopingAddr can be either 4 or + 16 bytes." + ::= { rbridgeGroup 9 } + + rbridgeDtreeGroup OBJECT-GROUP + OBJECTS { + rbridgeDtreePriority, + rbridgeDtreeActiveTrees, + rbridgeDtreeMaxTrees, + rbridgeDtreeDesiredUseTrees, + rbridgeDtreeNickname, + rbridgeDtreeIngress + } + STATUS current + DESCRIPTION + "A collection of objects providing information + about distribution trees." + ::= { rbridgeGroup 10 } + + rbridgeTrillGroup OBJECT-GROUP + OBJECTS { + rbridgeTrillMinMtuDesired, + rbridgeTrillSz, + rbridgeTrillMaxMtuProbes, + rbridgeTrillNbrMtu, + rbridgeTrillNbrFailedMtuTest + } + STATUS current + DESCRIPTION + "A collection of objects providing information + about TRILL neighbors." + ::= { rbridgeGroup 11 } + + rbridgeNotificationGroup NOTIFICATION-GROUP + NOTIFICATIONS { + rbridgeBaseNewDrb, + rbridgeBaseTopologyChange + } + STATUS current + DESCRIPTION + "A collection of objects describing notifications (traps)." + ::= { rbridgeGroup 12 } + + + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 49] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + -- ---------------------------------------------------------- -- + -- Compliance Statement + -- ---------------------------------------------------------- -- + + rbridgeCompliance MODULE-COMPLIANCE + STATUS current + DESCRIPTION + "The compliance statement for support of RBridge + services." + + MODULE + MANDATORY-GROUPS { + rbridgeBaseGroup, + rbridgeBaseNicknameGroup, + rbridgeBasePortGroup, + rbridgeFdbGroup, + rbridgeFibGroup, + rbridgeVlanGroup, + rbridgeDtreeGroup, + rbridgeTrillGroup, + rbridgeNotificationGroup + } + + GROUP rbridgePortCounterGroup + DESCRIPTION + "Implementation of this group is optional." + + GROUP rbridgeEsadiGroup + DESCRIPTION + "Implementation of this group is optional." + + GROUP rbridgeSnoopingGroup + DESCRIPTION + "Implementation of this group is optional." + + ::= { rbridgeCompliances 1 } + + rbridgeReadOnlyCompliance MODULE-COMPLIANCE + STATUS current + DESCRIPTION + "When this MIB is implemented in read-only mode, then + the implementation can claim read-only compliance. + In that case, RBridge objects can be monitored but + cannot be configured with this implementation." + + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 50] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + MODULE + MANDATORY-GROUPS { + rbridgeBaseGroup, + rbridgeBaseNicknameGroup, + rbridgeBasePortGroup, + rbridgeFdbGroup, + rbridgeFibGroup, + rbridgeVlanGroup, + rbridgeDtreeGroup, + rbridgeTrillGroup, + rbridgeNotificationGroup + } + + OBJECT rbridgeBaseForwardDelay + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeBaseUniMultipathEnable + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeBaseMultiMultipathEnable + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeBaseAcceptEncapNonadj + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeBaseNicknameNumber + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeBaseNicknamePriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeBaseNicknameDtrPriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + + + +Rijhsinghani & Zebrose Standards Track [Page 51] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + OBJECT rbridgeBaseNicknameRowStatus + SYNTAX INTEGER { active(1) } + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required, and 'active' is the only + status that needs to be supported." + + OBJECT rbridgeBasePortDisable + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeBasePortTrunkPort + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeBasePortAccessPort + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeBasePortP2pHellos + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeBasePortInhibitionTime + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeBasePortDisableLearning + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeBasePortDesiredDesigVlan + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeBasePortStpWiringCloset + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + + + + +Rijhsinghani & Zebrose Standards Track [Page 52] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + OBJECT rbridgeConfidenceNative + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeConfidenceDecap + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeConfidenceStatic + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeVlanDisableLearning + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeVlanPortAnnouncing + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeEsadiEnable + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeEsadiConfidence + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeEsadiDrbPriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeEsadiDrbHoldingTime + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeEsadiRowStatus + SYNTAX INTEGER { active(1) } + MIN-ACCESS read-only + + + +Rijhsinghani & Zebrose Standards Track [Page 53] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + DESCRIPTION + "Write access is not required, and 'active' is the only + status that needs to be supported." + + OBJECT rbridgeDtreePriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeTrillMinMtuDesired + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT rbridgeTrillMaxMtuProbes + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + GROUP rbridgePortCounterGroup + DESCRIPTION + "Implementation of this group is optional." + + GROUP rbridgeEsadiGroup + DESCRIPTION + "Implementation of this group is optional." + + GROUP rbridgeSnoopingGroup + DESCRIPTION + "Implementation of this group is optional." + + ::= { rbridgeCompliances 2 } + + END + + + + + + + + + + + + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 54] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + +8. Security Considerations + + This MIB relates to a system that will provide network connectivity + and packet-forwarding services. As such, improper manipulation of + the objects represented by this MIB may result in denial of service + to a large number of end-users. + + There are a number of management objects defined in this MIB module + with a MAX-ACCESS clause of read-write and/or read-create. Such + objects may be considered sensitive or vulnerable in some network + environments. The support for SET operations in a non-secure + environment without proper protection can have a negative effect on + network operations. These are the tables and objects and their + sensitivity/vulnerability: + + The following tables and objects in the RBRIDGE-MIB can be + manipulated to interfere with the operation of RBridges: + + o rbridgeBaseUniMultipathEnable affects the ability of the RBridge + to route unicast traffic over multiple paths, and + rbridgeBaseMultiMultipathEnable affects the ability of the RBridge + to route multi-destination traffic over multiple paths. + + o rbridgeBasePortTable contains a number of objects that may affect + network connectivity. Actions that may be triggered by + manipulating objects in this table include disabling of an RBridge + port, discarding of native packets, disabling learning, and + others. + + o rbridgeEsadiTable contains objects that affect the operation of + the ESADI protocol used for learning, and manipulation of the + objects contained therein can be used to confuse the learning + ability of RBridges. + + o rbridgeDtreePriority can affect computation of distribution trees + within an RBridge campus, thereby affecting the forwarding of + multi-destination traffic. + + o rbridgeTrillMinMtuDesired can affect the size of packets being + used to exchange information between RBridges. + + Some of the readable objects in this MIB module (i.e., objects with a + MAX-ACCESS other than not-accessible) may be considered sensitive or + vulnerable in some network environments. It is thus important to + control even GET and/or NOTIFY access to these objects and possibly + to even encrypt the values of these objects when sending them over + + + + + +Rijhsinghani & Zebrose Standards Track [Page 55] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + the network via SNMP. For example, access to network topology and + RBridge attributes can reveal information that should not be + available to all users of the network. + + SNMP versions prior to SNMPv3 did not include adequate security. + Even if the network itself is secure (for example by using IPsec), + there is no control as to who on the secure network is allowed to + access and GET/SET (read/change/create/delete) the objects in this + MIB module. + + Implementations SHOULD provide the security features described by the + SNMPv3 framework (see [RFC3410]), and implementations claiming + compliance to the SNMPv3 standard MUST include full support for + authentication and privacy via the User-based Security Model (USM) + [RFC3414] with the AES cipher algorithm [RFC3826]. Implementations + MAY also provide support for the Transport Security Model (TSM) + [RFC5591] in combination with a secure transport such as SSH + [RFC5592] or TLS/DTLS [RFC6353]. + + Further, deployment of SNMP versions prior to SNMPv3 is NOT + RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to + enable cryptographic security. It is then a customer/operator + responsibility to ensure that the SNMP entity giving access to an + instance of this MIB module is properly configured to give access to + the objects only to those principals (users) that have legitimate + rights to indeed GET or SET (change/create/delete) them. + + For other RBridge security considerations, see [RFC6325]. + +9. IANA Considerations + + The MIB module in this document uses the following IANA-assigned + OBJECT IDENTIFIER value recorded in the SMI Numbers registry: + + Descriptor OBJECT IDENTIFIER value + ---------- ----------------------- + + rbridgeMIB { mib-2 214 } + +10. Contributors + + The authors would like to acknowledge the contributions of Donald + Eastlake, Radia Perlman, Anoop Ghanwani, Dan Romascanu, Mahesh Akula, + Sue Hares, and Joan Cucchiara. + + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 56] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + +11. References + +11.1. Normative References + + [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate + Requirement Levels", BCP 14, RFC 2119, March 1997. + + [RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J. + Schoenwaelder, Ed., "Structure of Management Information + Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. + + [RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J. + Schoenwaelder, Ed., "Textual Conventions for SMIv2", + STD 58, RFC 2579, April 1999. + + [RFC2580] McCloghrie, K., Ed., Perkins, D., Ed., and J. + Schoenwaelder, Ed., "Conformance Statements for SMIv2", + STD 58, RFC 2580, April 1999. + + [RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group + MIB", RFC 2863, June 2000. + + [RFC3414] Blumenthal, U. and B. Wijnen, "User-based Security Model + (USM) for version 3 of the Simple Network Management + Protocol (SNMPv3)", STD 62, RFC 3414, December 2002. + + [RFC3826] Blumenthal, U., Maino, F., and K. McCloghrie, "The + Advanced Encryption Standard (AES) Cipher Algorithm in + the SNMP User-based Security Model", RFC 3826, June 2004. + + [RFC4001] Daniele, M., Haberman, B., Routhier, S., and J. + Schoenwaelder, "Textual Conventions for Internet Network + Addresses", RFC 4001, February 2005. + + [RFC4188] Norseth, K., Ed., and E. Bell, Ed., "Definitions of + Managed Objects for Bridges", RFC 4188, September 2005. + + [RFC4363] Levi, D. and D. Harrington, "Definitions of Managed + Objects for Bridges with Traffic Classes, Multicast + Filtering, and Virtual LAN Extensions", RFC 4363, + January 2006. + + [RFC4444] Parker, J., Ed., "Management Information Base for + Intermediate System to Intermediate System (IS-IS)", + RFC 4444, April 2006. + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 57] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + + [RFC5591] Harrington, D. and W. Hardaker, "Transport Security Model + for the Simple Network Management Protocol (SNMP)", + RFC 5591, June 2009. + + [RFC5592] Harrington, D., Salowey, J., and W. Hardaker, "Secure + Shell Transport Model for the Simple Network Management + Protocol (SNMP)", RFC 5592, June 2009. + + [RFC6325] Perlman, R., Eastlake 3rd, D., Dutt, D., Gai, S., and A. + Ghanwani, "Routing Bridges (RBridges): Base Protocol + Specification", RFC 6325, July 2011. + + [RFC6353] Hardaker, W., "Transport Layer Security (TLS) Transport + Model for the Simple Network Management Protocol (SNMP)", + RFC 6353, July 2011. + +11.2. Informative References + + [RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, + "Introduction and Applicability Statements for Internet- + Standard Management Framework", RFC 3410, December 2002. + + [RFC4663] Harrington, D., "Transferring MIB Work from IETF Bridge + MIB WG to IEEE 802.1 WG", RFC 4663, September 2006. + + [RFC5556] Touch, J. and R. Perlman, "Transparent Interconnection of + Lots of Links (TRILL): Problem and Applicability + Statement", RFC 5556, May 2009. + + + + + + + + + + + + + + + + + + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 58] + +RFC 6850 RBridges: TRILL Base MIB January 2013 + + +Authors' Addresses + + Anil Rijhsinghani + Hewlett-Packard + 153 Taylor St. + Littleton, MA + USA + + Phone: +1 508 323 1251 + EMail: anil@charter.net + + + Kate Zebrose + HW Embedded + 26 Josephine Ave. + Somerville, MA + USA + + Phone: +1 617 840 9673 + EMail: zebrose@alum.mit.edu + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +Rijhsinghani & Zebrose Standards Track [Page 59] + -- cgit v1.2.3