From 4bfd864f10b68b71482b35c818559068ef8d5797 Mon Sep 17 00:00:00 2001 From: Thomas Voss Date: Wed, 27 Nov 2024 20:54:24 +0100 Subject: doc: Add RFC documents --- doc/rfc/rfc7306.txt | 1907 +++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 1907 insertions(+) create mode 100644 doc/rfc/rfc7306.txt (limited to 'doc/rfc/rfc7306.txt') diff --git a/doc/rfc/rfc7306.txt b/doc/rfc/rfc7306.txt new file mode 100644 index 0000000..e3b1a7b --- /dev/null +++ b/doc/rfc/rfc7306.txt @@ -0,0 +1,1907 @@ + + + + + + +Internet Engineering Task Force (IETF) H. Shah +Request for Comments: 7306 Broadcom Corporation +Category: Standards Track F. Marti +ISSN: 2070-1721 W. Noureddine + A. Eiriksson + Chelsio Communications, Inc. + R. Sharp + Intel Corporation + June 2014 + + + Remote Direct Memory Access (RDMA) Protocol Extensions + +Abstract + + This document specifies extensions to the IETF Remote Direct Memory + Access Protocol (RDMAP) as specified in RFC 5040. RDMAP provides + read and write services directly to applications and enables data to + be transferred directly into Upper-Layer Protocol (ULP) Buffers + without intermediate data copies. The extensions specified in this + document provide the following capabilities and/or improvements: + Atomic Operations and Immediate Data. + +Status of This Memo + + This is an Internet Standards Track document. + + This document is a product of the Internet Engineering Task Force + (IETF). It represents the consensus of the IETF community. It has + received public review and has been approved for publication by the + Internet Engineering Steering Group (IESG). Further information on + Internet Standards is available in Section 2 of RFC 5741. + + Information about the current status of this document, any errata, + and how to provide feedback on it may be obtained at + http://www.rfc-editor.org/info/rfc7306. + + + + + + + + + + + + + + + +Shah, et al. Standards Track [Page 1] + +RFC 7306 RDMA Protocol Extensions June 2014 + + +Copyright Notice + + Copyright (c) 2014 IETF Trust and the persons identified as the + document authors. All rights reserved. + + This document is subject to BCP 78 and the IETF Trust's Legal + Provisions Relating to IETF Documents + (http://trustee.ietf.org/license-info) in effect on the date of + publication of this document. Please review these documents + carefully, as they describe your rights and restrictions with respect + to this document. Code Components extracted from this document must + include Simplified BSD License text as described in Section 4.e of + the Trust Legal Provisions and are provided without warranty as + described in the Simplified BSD License. + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +Shah, et al. Standards Track [Page 2] + +RFC 7306 RDMA Protocol Extensions June 2014 + + +Table of Contents + + 1. Introduction ....................................................4 + 1.1. Discovery of RDMAP Extensions ..............................5 + 2. Requirements Language ...........................................5 + 3. Glossary ........................................................6 + 4. Header Format Extensions ........................................7 + 4.1. RDMAP Control and Invalidate STag Fields ...................7 + 4.2. RDMA Message Definitions ...................................9 + 5. Atomic Operations ...............................................9 + 5.1. Atomic Operation Details ..................................10 + 5.1.1. FetchAdd ...........................................10 + 5.1.2. CmpSwap ............................................12 + 5.2. Atomic Operations .........................................13 + 5.2.1. Atomic Operation Request Message ...................14 + 5.2.2. Atomic Operation Response Message ..................17 + 5.3. Atomicity Guarantees ......................................18 + 5.4. Atomic Operations Ordering and Completion Rules ...........18 + 6. Immediate Data .................................................20 + 6.1. RDMAP Interactions with ULP for Immediate Data ............20 + 6.2. Immediate Data Header Format ..............................21 + 6.3. Immediate Data or Immediate Data with SE Message ..........21 + 6.4. Ordering and Completions ..................................22 + 7. Ordering and Completions Table .................................22 + 8. Error Processing ...............................................25 + 8.1. Errors Detected at the Local Peer .........................25 + 8.2. Errors Detected at the Remote Peer ........................26 + 9. Security Considerations ........................................26 + 10. IANA Considerations ...........................................27 + 10.1. RDMAP Message Atomic Operation Subcodes ..................27 + 10.2. RDMAP Queue Numbers ......................................28 + 11. References ....................................................29 + 11.1. Normative References .....................................29 + 11.2. Informative References ...................................29 + 12. Acknowledgments ...............................................30 + Appendix A. DDP Segment Formats for RDMA Messages .................31 + A.1. DDP Segment for Atomic Operation Request ..................32 + A.2. DDP Segment for Atomic Response ...........................33 + A.3. DDP Segment for Immediate Data and Immediate Data with SE .33 + + + + + + + + + + + + +Shah, et al. Standards Track [Page 3] + +RFC 7306 RDMA Protocol Extensions June 2014 + + +1. Introduction + + The RDMA Protocol [RFC5040] provides capabilities for zero-copy data + communications that preserve memory protection semantics, enabling + more efficient network protocol implementations. The RDMA Protocol + is part of the iWARP family of specifications which also include RFC + 5041 [RFC5041], RFC 5044 [RFC5044], and RFC 6581 [RFC6581]. This + document specifies the following extensions to the RDMA Protocol + (RDMAP): + + o Atomic Operations can be performed on remote memory locations. + Support for Atomic Operations enhances the usability of RDMAP in + distributed shared-memory environments. + + o Immediate Data messages allow the ULP at the sender to provide a + small amount of data. When an Immediate Data message is sent + following an RDMA Write Message, the combination of the two + messages is an implementation of RDMA Write with Immediate message + that is found in other RDMA transport protocols. + + Other RDMA transport protocols define the functionality added by + these extensions leading to differences in RDMA applications and/or + Upper-Layer Protocols. Removing these differences in the transport + protocols simplifies these applications and ULPs, and that is the + main motivation for the extensions specified in this document. + + RSockets [RSOCKETS] is an example of RDMA-enabled middleware that + provides a socket interface as the upper-edge interface and utilizes + RDMA to provide more efficient networking for socket-based + applications. RSockets is aware of Immediate Data support in + InfiniBand [IB]. RSockets cannot utilize the RDMA Write with + Immediate Data operation from InfiniBand. The addition of the + Immediate Data operation specified in this document will alleviate + this difference in RSockets when running on InfiniBand and iWARP. + + Structured high-performance computing applications based on the + Message-Passing Interface [MPI] may use Atomic Operations defined in + this specification. DAT Atomics [DAT_ATOMICS] is an example of RDMA- + enabled middleware that provides a portable RDMA programming + interface for various RDMA transport protocols. DAT Atomics includes + a primitive for InfiniBand that is not supported by iWARP RDMA- + enabled Network Interface Controllers or RNICs. The addition of + Atomic Operations as specified in this document will allow Atomic + Operations in DAT Atomics to work for both InfiniBand and RNICs + interchangeably. + + + + + + +Shah, et al. Standards Track [Page 4] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + For more background on RDMA Protocol applicability, see + "Applicability of Remote Direct Memory Access Protocol (RDMA) and + Direct Data Placement Protocol (DDP)" [RFC5045]. + +1.1. Discovery of RDMAP Extensions + + Today there are RDMA applications and/or ULPs that are aware of the + existence of Atomic and Immediate Data operations for RDMA transports + such as InfiniBand and application programming interfaces such as + Open Fabrics Verbs [OFAVERBS]. Today, these applications need to be + aware that RDMAP does not support certain of these operations. + Typically, the availability of these capabilities is exposed to the + applications through adapter query interfaces in software. + Applications then have to decide to use or not use Immediate Data or + Atomic Operations based on the results of the query interfaces. Such + query interfaces typically return the scope of atomicity guarantees, + not the individual Atomic Operations supported. Therefore, this + specification requires all Atomic Operations defined within to be + supported if an RNIC supports any Atomic Operations. + + In cases where heterogeneous hardware, with differing support for + Atomic Operations and Immediate Data Operations, is deployed for use + by RDMA applications and/or ULPs, applications are either statically + configured to use or not use optional features or use application- + specific negotiation mechanisms. For the extensions covered by this + document, it is RECOMMENDED that RDMA applications and/or ULPs + negotiate at the application or ULP level the usage of these + extensions. The definition of such application-specific mechanisms + is outside the scope of this specification. For backward + compatibility, existing applications and/or ULPs should not assume + that these extensions are supported. + + In the absence of application-specific negotiation of the features + defined within this specification, the new operations can be + attempted, and reported errors can be used to determine a remote + peer's capabilities. In the case of Atomics, a FetchAdd operation + with "Add Data" set to 0 can safely be used to determine the + existence of Atomic Operations without modifying the content of a + remote peer's memory. A Remote Operation Error or Unexpected OpCode + error will be reported by the remote peer if there is an Immediate + Data or Atomic Operation that is not supported by the remote peer. + +2. Requirements Language + + The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", + "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this + document are to be interpreted as described in RFC 2119 [RFC2119]. + + + + +Shah, et al. Standards Track [Page 5] + +RFC 7306 RDMA Protocol Extensions June 2014 + + +3. Glossary + + This document is an extension of RFC 5040, and key words are defined + in the glossary of that document. + + Atomic Operation - an operation that results in an execution of a + memory operation at a specific ULP Buffer address on a remote node + using the Tagged Buffer data transfer model. The consumer can use + Atomic Operations to read, modify, and write memory at the + destination ULP Buffer address, while at the same time + guaranteeing that no other Atomic Operation read or write accesses + to the ULP Buffer address targeted by the Atomic Operation will + occur across any other RDMAP Streams on an RNIC at the Responder. + + Atomic Operation Request - an RDMA Message used by the Data Source to + perform an Atomic Operation at the Responder. + + Atomic Operation Response - an RDMA Message used by the Responder to + describe the completion of an Atomic Operation at the Responder. + + CmpSwap - an Atomic Operation that is used to compare and swap a + value at a specific address on a remote node. + + FetchAdd - an Atomic Operation that is used to atomically increment a + value at a specific ULP Buffer address on a remote node. + + Immediate Data - a small fixed-size portion of data sent from the + Data Source to a Data Sink. + + Immediate Data Message - an RDMA Message used by the Data Source to + send Immediate Data to the Data Sink. + + Immediate Data with Solicited Event (SE) Message - an RDMA Message + used by the Data Source to send Immediate Data with Solicited + Event to the Data Sink. + + iWARP - a suite of wire protocols comprised of RFC 5040, RFC 5041, + RFC 5044, and RFC 6581. + + Requester - the sender of an RDMA Atomic Operation request. + + Responder - the receiver of an RDMA Atomic Operation request. + + RNIC - RDMA-enabled Network Interface Controller. In this context, + this would be a network I/O adapter or embedded controller with + iWARP functionality. + + + + + +Shah, et al. Standards Track [Page 6] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + ULP - Upper-Layer Protocol. The protocol layer above the one + currently being referenced. The ULP for RFC 5040 / RFC 5041 is + expected to be an OS, Application, adaptation layer, or + proprietary device. The RFC 5040 / RFC 5041 documents do not + specify a ULP -- they provide a set of semantics that allow a ULP + to be designed to utilize RFC 5040 / RFC 5041. + +4. Header Format Extensions + + The control information of RDMA Messages is included in header fields + defined in RFC 5041, the Direct Data Placement (DDP) protocol. RFC + 5040 defines the RDMAP header formats layered on the DDP header + definition. This specification extends RFC 5040 with the following + new formats: + + o Four new RDMA Messages carry additional RDMAP headers. The + Immediate Data operation and Immediate Data with Solicited Event + operation each include 8 bytes of data following the RDMAP header. + Atomic Operations include Atomic Request or Atomic Response + headers following the RDMAP header. The RDMAP header for Atomic + Request messages is 52 bytes long as specified in Figure 4. The + RDMAP header for Atomic Response Messages is 32 bytes long as + specified in Figure 5. + + o Introduction of a new queue for untagged Buffers (QN=3) used for + Atomic Response tracking. + +4.1. RDMAP Control and Invalidate STag Fields + + For reference, Figure 1 depicts the format of the DDP Control and + RDMAP Control Fields, in the style and convention of RFC 5040: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |T|L| Resrv | DV| RV|Rsv| Opcode| + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Invalidate STag | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + Figure 1: DDP Control and RDMAP Control Fields + + The DDP Control Field consists of the T (Tagged), L (Last), Resrv, + and DV (DDP protocol Version) fields [RFC5041]. The RDMAP Control + Field consists of the RV (RDMA Version), Rsv, and Opcode fields + [RFC5040]. + + + + + +Shah, et al. Standards Track [Page 7] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + This specification adds values for the RDMA Opcode field to those + specified in RFC 5040. Figure 2 defines the new values of the RDMA + Opcode field that are used for the RDMA Messages defined in this + specification. + + As shown in Figure 2, STag (Steering Tag) and Tagged Offset are not + applicable for the RDMA Messages defined in this specification. + Figure 2 also shows the appropriate Queue Number for each Opcode. + + All RDMA Messages defined in this specification MUST have: + + The RDMA Version (RV) field: 01b. + + Opcode field: Set to one of the values in Figure 2. + + Invalidate STag: Set to zero by the sender, ignored by the receiver. + + -------+-----------+-------+------+-------+---------+------------- + RDMA | Message | Tagged| STag | Queue | In- | Message + Opcode | Type | Flag | and | Number| validate| Length + | | | TO | | STag | Communicated + | | | | | | between DDP + | | | | | | and RDMAP + -------+-----------+-------+------+-------+---------+------------- + 1000b | Immediate | 0 | N/A | 0 | N/A | Yes + | Data | | | | | + -------+-----------+---------------------------------------------- + 1001b | Immediate | 0 | N/A | 0 | N/A | Yes + | Data with | | | | | + | SE | | | | | + -------+-----------+---------------------------------------------- + 1010b | Atomic | 0 | N/A | 1 | N/A | Yes + | Request | | | | | + -------+-----------+---------------------------------------------- + 1011b | Atomic | 0 | N/A | 3 | N/A | Yes + | Response | | | | | + -------+-----------+---------------------------------------------- + + Figure 2: Additional RDMA Usage of DDP Fields + + Note: N/A means Not Applicable. + + This extension defines RDMAP use of Queue Number 3 for Untagged + Buffers for Atomic Responses. This queue is used for tracking + outstanding Atomic Requests. + + All other DDP and RDMAP Control Fields are set as described in RFC + 5040. + + + +Shah, et al. Standards Track [Page 8] + +RFC 7306 RDMA Protocol Extensions June 2014 + + +4.2. RDMA Message Definitions + + The following figure defines which RDMA Headers are used on each new + RDMA Message and which new RDMA Messages are allowed to carry ULP + payload. + + -------+-----------+-------------------+------------------------- + RDMA | Message | RDMA Header Used | ULP Message allowed in + Message| Type | | the RDMA Message + OpCode | | | + | | | + -------+-----------+-------------------+------------------------- + 1000b | Immediate | Immediate Data | No + | Data | Header | + -------+-----------+-------------------+------------------------- + 1001b | Immediate | Immediate Data | No + | Data with | Header | + | SE | | + -------+-----------+-------------------+------------------------- + 1010b | Atomic | Atomic Request | No + | Request | Header | + -------+-----------+-------------------+------------------------- + 1011b | Atomic | Atomic Response | No + | Response | Header | + -------+-----------+-------------------+------------------------- + + Figure 3: RDMA Message Definitions + +5. Atomic Operations + + The RDMA Protocol Specification in RFC 5040 does not include support + for Atomic Operations, which are an important building block for + implementing distributed shared memory. + + This document extends the RDMA Protocol specification with a set of + basic Atomic Operations and specifies their resource and ordering + rules. The Atomic Operations specified in this document provide + equivalent functionality to the InfiniBand RDMA transport as well as + extended Atomic Operations defined in Open Fabrics Verbs, to allow + applications that use these primitives to work interchangeably over + iWARP. Other operations are left for future consideration. + + Atomic Operations as specified in this document execute a 64-bit + memory operation at a specified destination ULP Buffer address on a + Responder node using the Tagged Buffer data transfer model. The + operations atomically read, modify, and write back the contents of + the destination ULP Buffer address and guarantee that Atomic + Operations on this ULP Buffer address by other RDMAP Streams on the + + + +Shah, et al. Standards Track [Page 9] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + same RNIC do not occur between the read and the write caused by the + Atomic Operation. Therefore, the Responder RNIC MUST implement + mechanisms to prevent Atomic Operations to a memory registered for + Atomic Operations while an Atomic Operation targeting the memory is + in progress. The Requester of an Atomic Operation cannot rely on + Atomic Operation behavior at the Responder across multiple RNICs or + with respect to other applications/ULPs running at the Responder that + can access the ULP Buffer. It is OPTIONAL for an RNIC to provide + such behavior when implementing the Atomic Operations specified in + this document. An RNIC that supports Atomic Operations as specified + in this document MUST implement both the FetchAdd operation as + specified in Section 5.1.1 and the CmpSwap operation as specified in + Section 5.1.2. The advertisement of Tagged Buffer information for + Atomic Operations is outside the scope of this specification and is + handled by the ULPs. + + Implementation note: It is RECOMMENDED that the applications do not + use the ULP Buffer addresses used for Atomic Operations for other + RDMA operations due to the lack of atomicity guarantees between + operations other than Atomic Operations. + + Implementation note: Errors related to the alignment in the following + sections cover Atomic Operations targeted at a ULP Buffer address + that is not aligned to a 64-bit boundary. + + Atomic Operation Request Messages use the same remote addressing + mechanism as RDMA Reads and Writes. The ULP Buffer address specified + in the request is in the address space of the Remote Peer to which + the Atomic Operation is targeted. + + Atomic Operation Response Messages MUST use the Untagged Buffer model + with QN=3. Queue number 3 will be used to track outstanding Atomic + Operation Request messages at the Requester. When the Atomic + Operation Response message is received, the Message Sequence Number + (MSN) will be used to locate the corresponding Atomic Operation + request in order to complete the Atomic Operation request. + +5.1. Atomic Operation Details + + The following subsections describe the Atomic Operations in more + detail. + +5.1.1. FetchAdd + + The FetchAdd Atomic Operation requests the Responder to read a 64-bit + Original Remote Data Value at a 64-bit aligned ULP Buffer address in + the Responder's memory, perform the FetchAdd operation on multiple + fields of selectable length specified by 64-bit "Add Mask", and write + + + +Shah, et al. Standards Track [Page 10] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + the result back to the same ULP Buffer address. The Atomic addition + is performed independently on each one of these fields. A bit set in + the Add Mask field specifies the field boundary; for each field, a + bit is set at the most significant bit position for each field, + causing any carry out of that bit position to be discarded when the + addition is performed. + + FetchAdd Atomic Operations MUST target ULP Buffer addresses that are + 64-bit aligned. FetchAdd Atomic Operations that target ULP Buffer + addresses that are not 64-bit aligned MUST be surfaced as errors, and + the Responder's memory MUST NOT be modified in such cases. + Additionally, an error MUST be surfaced and a terminate message MUST + be generated. The setting of the Add Mask field to + 0x0000000000000000 results in Atomic Add of 64-bit Original Remote + Data Value and 64-bit "Add Data". + + The pseudocode below describes a masked FetchAdd Atomic Operation. + + bit_location = 1 + + carry = 0 + + Remote Data Value = 0 + + for bit = 0 to 63 + + { + + if (bit != 0 ) bit_location = bit_location << 1 + + val1 = (Original Remote Data Value & bit_location) >> bit + + val2 = (Add Data & bit_location) >> bit + sum = carry + val1 + val2 + + carry = (sum & 2) >> 1 + + sum = sum & 1 + + if (sum) + + Remote Data Value |= bit_location + + carry = ((carry) && (!(Add Mask & bit_location))) + + } + + + + + +Shah, et al. Standards Track [Page 11] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + The FetchAdd operation is performed in the endian format of the + target memory. The "Original Remote Data Value" is converted from + the endian format of the target memory for return and returned to the + Requester. The fields are in big-endian format on the wire. + + The Requester specifies: + + o Remote STag + + o Remote Tagged Offset + + o Add Data + + o Add Mask + + The Responder returns: + + o Original Remote Data + +5.1.2. CmpSwap + + The CmpSwap Atomic Operation requires the Responder to read a 64-bit + value at a ULP Buffer address that is 64-bit aligned in the + Responder's memory, to perform an AND logical operation using the + 64-bit Compare Mask field in the Atomic Operation Request header, + then to compare it with the result of a logical AND operation of the + Compare Mask and the Compare Data fields in the header. If the two + values are equal, the Responder is required to swap masked bits in + the same ULP Buffer address with the masked Swap Data. If the two + masked compare values are not equal, the contents of the Responder's + memory are not changed. In either case, the original value read from + the ULP Buffer address is converted from the endian format of the + target memory for return and returned to the Requester. The fields + are in big-endian format on the wire. + + The Requester specifies: + + o Remote STag + + o Remote Tagged Offset + + o Swap Data + + o Swap Mask + + o Compare Data + + o Compare Mask + + + +Shah, et al. Standards Track [Page 12] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + The Responder returns: + + o Original Remote Data Value + + The following pseudocode describes the masked CmpSwap operation + result. + + if (!((Compare Data ^ Original Remote Data Value) & + + Compare Mask)) + + then + + Remote Data Value = + + (Original Remote Data Value & ~(Swap Mask)) + + | (Swap Data & Swap Mask) + + else + + Remote Data Value = Original Remote Data Value + + After the operation, the remote data Buffer MUST contain the + "Original Remote Data Value" (if comparison did not match) or the + masked "Swap Data" (if the comparison did match). CmpSwap Atomic + Operations MUST target ULP Buffer addresses that are 64-bit aligned. + + If a CmpSwap Atomic Operation is attempted on a target ULP Buffer + address that is not 64-bit aligned: + + o The operation MUST NOT be performed, + + o The Responder's memory MUST NOT be modified, + + o The result MUST be surfaced as an error, and + + o A terminate message MUST be generated. (See Section 8.2 for the + contents of the terminate message.) + +5.2. Atomic Operations + + The Atomic Operation Request and Response are RDMA Messages. An + Atomic Operation makes use of the DDP Untagged Buffer Model. Atomic + Operation Request messages MUST use the same Queue Number as RDMA + Read Requests (QN=1). Reusing the same Queue Number for Atomic + Request messages allows the Atomic Operations to reuse the same + infrastructure (e.g., Outbound and Inbound RDMA Read Queue Depth + + + +Shah, et al. Standards Track [Page 13] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + (ORD/IRD) flow control) as defined for RDMA Read Requests. Atomic + Operation Response messages MUST set Queue Number (QN) to 3 in the + DDP header. + + The RDMA Message OpCode for an Atomic Request Message is 1010b. The + RDMA Message OpCode for an Atomic Response Message is 1011b. + +5.2.1. Atomic Operation Request Message + + The Atomic Operation Request Message carries an Atomic Operation + Header that describes the ULP Buffer address in the Responder's + memory. The Atomic Operation Request header immediately follows the + DDP header. The RDMAP layer passes to the DDP layer a RDMAP Control + Field. The following figure depicts the Atomic Operation Request + Header that is used for all Atomic Operation Request Messages: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Reserved (Not Used) |AOpCode| + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Request Identifier | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Remote STag | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Remote Tagged Offset | + + + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Add or Swap Data | + + + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Add or Swap Mask | + + + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Compare Data | + + + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Compare Mask | + + + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + Figure 4: Atomic Operation Request Header + + + + +Shah, et al. Standards Track [Page 14] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + Reserved (Not Used): 28 bits + + This field is set to zero on transmit, ignored on receive. + + Atomic Operation Code (AOpCode): 4 bits. + + See Figure 5. All Atomic Operation Codes from Figure 5 MUST be + implemented by an RNIC that supports Atomic Operations. + + Request Identifier: 32 bits. + + The Request Identifier specifies a number that is used to + identify the Atomic Operation Request Message. The value used + in this field is selected by the RNIC that sends the message, + and it is reflected back to the Local Peer in the Atomic + Operation Response message. + + Remote STag: 32 bits. + + The Remote STag identifies the Remote Peer's Tagged Buffer + targeted by the Atomic Operation. The Remote STag is + associated with the RDMAP Stream through a mechanism that is + outside the scope of the RDMAP specification. + + Remote Tagged Offset: 64 bits. + + The Remote Tagged Offset specifies the starting offset, in + octets, from the base of the Remote Peer's Tagged Buffer + targeted by the Atomic Operation. The Remote Tagged Offset MAY + start at an arbitrary offset but MUST represent a ULP Buffer + address that is 64-bit aligned. + + Add or Swap Data: 64 bits. + + The Add or Swap Data field specifies the 64-bit "Add Data" + value in an Atomic FetchAdd Operation or the 64-bit "Swap Data" + value in an Atomic Swap or CmpSwap Operation. + + Add or Swap Mask: 64 bits + + This field is used in masked Atomic Operations (FetchAdd and + CmpSwap) to perform a bitwise logical AND operation as + specified in the definition of these operations. For non- + masked Atomic Operations (Swap), this field is set to + ffffffffffffffffh on transmit and ignored by the receiver. + + + + + + +Shah, et al. Standards Track [Page 15] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + Compare Data: 64 bits. + + The Compare Data field specifies the 64-bit "Compare Data" + value in an Atomic CmpSwap Operation. For Atomic Operations + FetchAdd and Atomic Swap, the Compare Data field is set to zero + on transmit and ignored by the receiver. + + Compare Mask: 64 bits + + This field is used in masked Atomic Operation CmpSwap to + perform a bitwise logical AND operation as specified in the + definition of these operations. For Atomic Operations FetchAdd + and Swap, this field is set to ffffffffffffffffh on transmit + and ignored by the receiver. + + ---------+-----------+----------+----------+---------+--------- + Atomic | Atomic | Add or | Add or | Compare | Compare + Operation| Operation | Swap | Swap | Data | Mask + Code | | Data | Mask | | + ---------+-----------+----------+----------+---------+--------- + 0000b | FetchAdd | Add Data | Add Mask | N/A | N/A + ---------+-----------+----------+----------+---------+--------- + 0010b | CmpSwap | Swap Data| Swap Mask| Valid | Valid + ---------+-----------+----------------------------------------- + + Figure 5: Atomic Operation Message Definitions + + The Atomic Operation Request Message has the following semantics: + + 1. An Atomic Operation Request Message MUST reference an Untagged + Buffer. That is, the Local Peer's RDMAP layer MUST request that + the DDP mark the Message as Untagged. + + 2. One Atomic Operation Request Message MUST consume one Untagged + Buffer. + + 3. The Responder's RDMAP layer MUST process an Atomic Operation + Request Message. A valid Atomic Operation Request Message MUST + NOT be delivered to the Responder's ULP (i.e., it is processed by + the RDMAP layer). + + 4. At the Responder, an error MUST be surfaced in response to + delivery to the Remote Peer's RDMAP layer of an Atomic Operation + Request Message with an Atomic Operation Code that the RNIC does + not support. + + + + + + +Shah, et al. Standards Track [Page 16] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + 5. An Atomic Operation Request Message MUST reference the RDMA Read + Request Queue. That is, the Requester's RDMAP layer MUST request + that the DDP layer set the Queue Number field to one. + + 6. The Requester MUST pass to the DDP layer Atomic Operation Request + Messages in the order they were submitted by the ULP. + + 7. The Responder MUST process the Atomic Operation Request Messages + in the order they were sent. + + 8. If the Responder receives a valid Atomic Operation Request + Message, it MUST respond with a valid Atomic Operation Response + Message. + +5.2.2. Atomic Operation Response Message + + The Atomic Operation Response Message carries an Atomic Operation + Response Header that contains the "Original Request Identifier" and + "Original Remote Data Value". The Atomic Operation Response Header + immediately follows the DDP header. The RDMAP layer passes to the + DDP layer a RDMAP Control Field. The following figure depicts the + Atomic Operation Response header that is used for all Atomic + Operation Response Messages: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Original Request Identifier | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Original Remote Data Value | + + + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + Figure 6: Atomic Operation Response Header + + Original Request Identifier: 32 bits. + + The Original Request Identifier is set to the value specified in + the Request Identifier field that was originally provided in the + corresponding Atomic Operation Request Message. + + Original Remote Data Value: 64 bits. + + The Original Remote Value specifies the original 64-bit value + stored at the ULP Buffer address targeted by the Atomic Operation. + + + + + +Shah, et al. Standards Track [Page 17] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + The Atomic Operation Response Message has the following semantics: + + 1. The Atomic Operation Response Message for the associated Atomic + Operation Request Message travels in the opposite direction. + + 2. An Atomic Operation Response Message MUST consume an Untagged + Buffer. That is, the Responder RDMAP layer MUST request that the + DDP mark the Message as Untagged. + + 3. An Atomic Operation Response Message MUST reference the Queue + Number 3. That is, the Responder's RDMAP layer MUST request that + the DDP layer set the Queue Number field to 3. + + 4. The Responder MUST ensure that a sufficient number of Untagged + Buffers are available on the RDMA Read Request Queue (Queue with + DDP Queue Number 1) to support the maximum number of Atomic + Operation Requests negotiated by the ULP in addition to the + maximum number of RDMA Read Requests negotiated by the ULP. + + 5. The Requester MUST ensure that a sufficient number of Untagged + Buffers are available on the RDMA Atomic Response Queue (Queue + with DDP Queue Number 3) to support the maximum number of Atomic + Operation Requests negotiated by the ULP. + + 6. The RDMAP layer MUST Deliver the Atomic Operation Response Message + to the ULP. + + 7. At the Requester, when an invalid Atomic Operation Response + Message is delivered to the Remote Peer's RDMAP layer, an error is + surfaced. + + 8. When the Responder receives Atomic Operation Request messages, the + Responder RDMAP layer MUST pass Atomic Operation Response Messages + to the DDP layer, in the order that the Atomic Operation Request + Messages were received by the RDMAP layer, at the Responder. + +5.3. Atomicity Guarantees + + Atomicity of the Read-Modify-Write (RMW) on the Responder's node by + the Atomic Operation MUST be assured in the context of concurrent + atomic accesses by other RDMAP Streams on the same RNIC. + +5.4. Atomic Operations Ordering and Completion Rules + + In addition to the ordering and completion rules described in RFC + 5040, the following rules apply to implementations of the Atomic + Operations. + + + + +Shah, et al. Standards Track [Page 18] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + 1. For an Atomic Operation, the Requester MUST NOT consider the + contents of the Tagged Buffer at the Responder to be modified by + that specific Atomic Operation until the Atomic Operation Response + Message has been Delivered to RDMAP at the Requester. + + 2. Atomicity guarantees MUST be provided within the scope of a single + RNIC. + + Implementation Note: This requirement for atomicity among + operations is limited to the scope of a single RNIC. Atomicity + guarantees are OPTIONAL with respect to access to the Tagged + Buffer by any other method than an Atomic Operation via the same + RNIC. Examples of such accesses that may not be atomic with + respect to an Atomic Operation include accesses via other RNICs + and local processor memory access to the Tagged Buffer. + + 3. Atomic Operation Request Messages MUST NOT start processing at the + Responder until they have been Delivered to RDMAP by DDP. + + 4. Atomic Operation Response Messages MAY be generated at the + Responder after subsequent RDMA Write Messages or Send Messages + have been Placed or Delivered. + + 5. Atomic Operation Response Message processing at the Responder MUST + be started only after the Atomic Operation Request Message has + been Delivered by the DDP layer (thus, all previous RDMA Messages + on that DDP Stream have been Delivered). + + 6. Send Messages MAY be Completed at the Responder before prior + incoming Atomic Operation Request Messages have completed their + response processing. + + 7. An Atomic Operation MUST NOT be Completed at the Requester until + the DDP layer Delivers the associated incoming Atomic Operation + Response Message. + + 8. If more than one outstanding Atomic Request Message is supported + by both peers, the Atomic Operation Request Messages MUST be + processed in the order they were delivered by the DDP layer on the + Responder. Atomic Operation Response Messages MUST be submitted + to the DDP layer on the Responder in the order the Atomic + Operation Request Messages were Delivered by DDP. + + + + + + + + + +Shah, et al. Standards Track [Page 19] + +RFC 7306 RDMA Protocol Extensions June 2014 + + +6. Immediate Data + + The Immediate Data operation is typically used in conjunction with an + RDMA Write Operation to improve ULP processing efficiency. The + efficiency is gained by causing an RDMA Completion to be generated + immediately following the RDMA Write operation. This RDMA Completion + delivers 8 bytes of Immediate Data at the Remote Peer. The + combination of an RDMA Write Message followed by an Immediate Data + Operation has the same behavior as the RDMA Write with Immediate Data + operation found in InfiniBand. An Immediate Data operation that is + not preceded by an RDMA Write operation causes an RDMA Completion. + +6.1. RDMAP Interactions with ULP for Immediate Data + + For Immediate Data operations, the following are the interactions + between the RDMAP Layer and the ULP: + + o At the Data Source: + + - The ULP passes to the RDMAP Layer the following: + + * 8 bytes of ULP Immediate Data + + - When the Immediate Data operation Completes, an indication of + the Completion results. + + o At the Data Sink: + + - If the Immediate Data operation is Completed successfully, the + RDMAP Layer passes the following information to the ULP Layer: + + * 8 bytes of Immediate Data + + * An Event, if the Data Sink is configured to generate an + Event. + + - If the Immediate Data operation is Completed in error, the Data + Sink RDMAP Layer will pass up the corresponding error + information to the Data Sink ULP and send a Terminate Message + to the Data Source RDMAP Layer. The Data Source RDMAP Layer + will then pass up the Terminate Message to the ULP. + + + + + + + + + + +Shah, et al. Standards Track [Page 20] + +RFC 7306 RDMA Protocol Extensions June 2014 + + +6.2. Immediate Data Header Format + + The Immediate Data and Immediate Data with SE Messages carry + Immediate Data as shown in Figure 7. The RDMAP layer passes to the + DDP layer an RDMAP Control Field and 8 bytes of Immediate Data. The + first 8 bytes of the data following the DDP header contains the + Immediate Data. See Appendix A.3 for the DDP segment format of an + Immediate Data or Immediate Data with SE Message. + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Immediate Data | + + + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + Figure 7: Immediate Data or Immediate Data with SE Message Header + + Immediate Data: 64 bits. + 8 bytes of data transferred from the Data Source to an untagged + Buffer at the Data Sink. + +6.3. Immediate Data or Immediate Data with SE Message + + The Immediate Data or Immediate Data with SE Message uses the DDP + Untagged Buffer Model to transfer Immediate Data from the Data Source + to the Data Sink. + + o An Immediate Data or Immediate Data with SE Message MUST reference + an Untagged Buffer. That is, the Local Peer's RDMAP Layer MUST + request that the DDP layer mark the Message as Untagged. + + o One Immediate Data or Immediate Data with SE Message MUST consume + one Untagged Buffer. + + o At the Remote Peer, the Immediate Data and Immediate Data with SE + Messages MUST be Delivered to the Remote Peer's ULP in the order + they were sent. + + o For an Immediate Data or Immediate Data with SE Message, the Local + Peer's RDMAP Layer MUST request that the DDP layer set the Queue + Number field to zero. + + o For an Immediate Data or Immediate Data with SE Message, the Local + Peer's RDMAP Layer MUST request that the DDP layer transmit 8 + bytes of data. + + + + +Shah, et al. Standards Track [Page 21] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + o The Local Peer MUST issue Immediate Data and Immediate Data with + SE Messages in the order they were submitted by the ULP. + + o The Remote Peer MUST check that Immediate Data and Immediate Data + with SE Messages include exactly 8 bytes of data from the DDP + layer. The DDP header carries the length field that is reported + by the DDP layer. + +6.4. Ordering and Completions + + Ordering and completion rules for Immediate Data are the same as + those for a Send operation as described in Section 5.5 of RFC 5040. + +7. Ordering and Completions Table + + The following table summarizes the ordering relationships for Atomic + and Immediate Data operations from the standpoint of the Local Peer + issuing the Operations. Note that in the table that follows, Send + includes Send, Send with Invalidate, Send with Solicited Event, and + Send with Solicited Event and Invalidate. Also note that in the + table below, Immediate Data includes Immediate Data and Immediate + Data with Solicited Event. + + ---------+----------+-------------+-------------+------------------ + First | Second | Placement | Placement | Ordering + Operation| Operation| Guarantee at| Guarantee at| Guarantee at + | | Remote Peer | Local Peer | Remote Peer + ---------+----------+-------------+-------------+------------------ + Immediate| Send | No Placement| Not | Completed in + Data | | Guarantee | Applicable | Order + | | between Send| | + | | Payload and | | + | | Immediate | | + | | Data | | + ---------+----------+-------------+-------------+------------------ + Immediate| RDMA | No Placement| Not | Not + Data | Write | Guarantee | Applicable | Applicable + | | between RDMA| | + | | Write | | + | | Payload and | | + | | Immediate | | + | | Data | | + + + + + + + + + +Shah, et al. Standards Track [Page 22] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + ---------+----------+-------------+-------------+------------------ + Immediate| RDMA | No Placement| RDMA Read | RDMA Read + Data | Read | Guarantee | Response | Response + | | between | will not be | Message will + | | Immediate | Placed until| not be + | | Data and | Immediate | generated + | | RDMA Read | Data is | until + | | Request | Placed at | Immediate Data + | | | Remote Peer | has been + | | | | Completed + ---------+----------+-------------+-------------+------------------ + Immediate| Atomic | No Placement| Atomic | Atomic + Data | | Guarantee | Response | Response + | | between | will not be | Message will + | | Immediate | Placed until| not be + | | Data and | Immediate | generated + | | Atomic | Data is | until + | | Request | Placed at | Immediate Data + | | | Remote Peer | has been + | | | | Completed + ---------+----------+-------------+-------------+------------------ + Immediate| Immediate| No Placement| Not | Completed in + Data or | Data | Guarantee | Applicable | Order + Send | | | | + ---------+----------+-------------+-------------+------------------ + RDMA | Immediate| No Placement| Not | Immediate Data + Write | Data | Guarantee | Applicable | is Completed + | | | | after RDMA + | | | | Write is Placed + | | | | and Delivered + ---------+----------+-------------+-------------+------------------ + RDMA Read| Immediate| No Placement| Immediate | Not Applicable + | Data | Guarantee | Data MAY be | + | | between | Placed | + | | Immediate | before | + | | Data and | RDMA Read | + | | RDMA Read | Response is | + | | Request | generated | + ---------+----------+-------------+-------------+------------------ + Atomic | Immediate| No Placement| Immediate | Not Applicable + | Data | Guarantee | Data MAY be | + | | between | Placed | + | | Immediate | before | + | | Data and | Atomic | + | | Atomic | Response is | + | | Request | generated | + + + + + +Shah, et al. Standards Track [Page 23] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + ---------+----------+-------------+-------------+------------------ + Atomic | Send | No Placement| Send Payload| Not Applicable + | | Guarantee | MAY be | + | | between Send| Placed | + | | Payload and | before | + | | Atomic | Atomic | + | | Request | Response is | + | | | generated | + ---------+----------+-------------+-------------+------------------ + Atomic | RDMA | No Placement| RDMA Write | Not + | Write | Guarantee | Payload MAY | Applicable + | | between RDMA| be Placed | + | | Write | before | + | | Payload and | Atomic | + | | Atomic | Response is | + | | Request | generated | + ---------+----------+-------------+-------------+------------------ + Atomic | RDMA | No Placement| No Placement| RDMA Read + | Read | Guarantee | Guarantee | Response + | | between | between | Message will + | | Atomic | Atomic | not be + | | Request and | Response | generated + | | RDMA Read | and RDMA | until Atomic + | | Request | Read | Response Message + | | | Response | has been + | | | | generated + ---------+----------+-------------+-------------+------------------ + Atomic | Atomic | Placed in | No Placement| Second Atomic + | | order | Guarantee | Request + | | | between two | Message will + | | | Atomic | not be + | | | Responses | processed + | | | | until first + | | | | Atomic Response + | | | | has been + | | | | generated + ---------+----------+-------------+-------------+------------------ + Send | Atomic | No Placement| Atomic | Atomic Response + | | Guarantee | Response | Message will not + | | between Send| will not be | be generated + | | Payload and | Placed at | until Send has + | | Atomic | the Local | been Completed + | | Request | Peer until | + | | | Send Payload| + | | | is Placed | + | | | at the | + | | | Remote Peer | + + + + +Shah, et al. Standards Track [Page 24] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + ---------+----------+-------------+-------------+------------------ + RDMA | Atomic | No Placement| Atomic | Not + Write | | Guarantee | Response | Applicable + | | between RDMA| will not be | + | | Write | Placed at | + | | Payload and | the Local | + | | Atomic | Peer until | + | | Request | RDMA Write | + | | | Payload | + | | | is Placed | + | | | at the | + | | | Remote Peer | + ---------+----------+-------------+-------------+------------------ + RDMA | Atomic | No Placement| No Placement| Atomic Response + Read | | Guarantee | Guarantee | Message will + | | between | between | not be generated + | | Atomic | Atomic | until RDMA + | | Request and | Response | Read Response + | | RDMA Read | and RDMA | has been + | | Request | Read | generated + | | | Response | + ---------+----------+-------------+-------------+------------------ + +8. Error Processing + + In addition to the error processing described in Section 7 of RFC + 5040, the following rules apply for the new RDMA Messages defined in + this specification. + +8.1. Errors Detected at the Local Peer + + The Local Peer MUST send a Terminate Message for each of the + following cases: + + 1. For errors detected while creating an Atomic Request, Atomic + Response, Immediate Data, or Immediate Data with SE Message, or + other reasons not directly associated with an incoming Message, + the Terminate Message and Error code are sent instead of the + Message. In this case, the Error Type and Error Code fields are + included in the Terminate Message, but the Terminated DDP Header + and Terminated RDMA Header fields are set to zero. + + 2. For errors detected on an incoming Atomic Request, Atomic + Response, Immediate Data, or Immediate Data with SE (after the + Message has been Delivered by DDP), the Terminate Message is sent + at the earliest possible opportunity, preferably in the next + + + + + +Shah, et al. Standards Track [Page 25] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + outgoing RDMA Message. In this case, the Error Type, Error Code, + and Terminated DDP Header fields are included in the Terminate + Message, but the Terminated RDMA Header field is set to zero. + +8.2. Errors Detected at the Remote Peer + + On incoming Atomic Requests, Atomic Responses, Immediate Data, and + Immediate Data with Solicited Event, the following MUST be validated: + + o The DDP layer MUST validate all DDP Segment fields. + + o The RDMA OpCode MUST be valid. + + o The RDMA Version MUST be valid. + + On incoming Atomic requests the following additional validation MUST + be performed: + + o The RDMAP layer MUST validate that the Remote Peer's Tagged ULP + Buffer address references a ULP Buffer address that is 64-bit + aligned. In the case of an error, the RDMAP layer MUST generate a + Terminate Message indicating RDMA Layer Remote Operation Error + with Error Code Name "Catastrophic error, localized to RDMAP + Stream" as described in Section 4.8 of RFC 5040. Implementation + Note: A ULP implementation can avoid this error by having the + target ULP Buffer of an Atomic Operation 64-bit aligned. + +9. Security Considerations + + This document specifies extensions to the RDMA Protocol specification + in RFC 5040, and as such the Security Considerations discussed in + Section 8 of RFC 5040 apply. In particular, Atomic Operations use + ULP Buffer addresses for the Remote Peer Buffer addressing used in + RFC 5040 as required by the security model described in RFC 5042 + [RFC5042]. + + RDMAP and related protocols may be used by applications that exhibit + distinctive traffic characteristics such as message timing, source, + destination, and size patterns. Examples include structured high- + performance computing applications based on the MPI interface. For + such applications, analysis of encrypted traffic could reveal + sensitive information, e.g., the nature of the application, size of + data set being used, and information about the application's rate of + progress. Such information can be hidden from passive observation + via use of Encapsulating Security Payload version 3 (ESPv3) Traffic + Flow Confidentiality [RFC4303] to obfuscate the encrypted traffic's + characteristics. ESPv3 implementation requirements for RDMAP are + specified in [RFC7146]. + + + +Shah, et al. Standards Track [Page 26] + +RFC 7306 RDMA Protocol Extensions June 2014 + + +10. IANA Considerations + + IANA has added the following entries to the "RDMAP Message Operation + Codes" registry of "Remote Direct Data Placement (RDDP)" registry: + + 0x8, Immediate Data, this specification + + 0x9, Immediate Data with Solicited Event, this specification + + 0xA, Atomic Request, this specification + + 0xB, Atomic Response, this specification + + In addition, the following registry has been added to the "Remote + Direct Data Placement (RDDP)" registry. The following section + specifies the registry, its initial contents, and the administration + policy in more detail. + +10.1. RDMAP Message Atomic Operation Subcodes + + Name of the registry: "RDMAP Message Atomic Operation Subcodes" + + Namespace details: RDMAP Message Atomic Operation Subcodes are 4-bit + values. + + Information that must be provided to assign a new value: An IESG- + approved Standards Track specification defining the semantics and + interoperability requirements of the proposed new value and the + fields to be recorded in the registry. + + Fields to record in the registry: RDMAP Message Atomic Operation + Subcode, Atomic Operation, RFC Reference. + + Initial registry contents: + + 0x0, FetchAdd, this specification + + 0x1, Reserved, this specification + + 0x2, CmpSwap, this specification + + Note: An experimental RDMAP Message Operation Code has already been + allocated; hence, there is no need for an experimental RDMAP Message + Atomic Operation Subcode. + + + + + + + +Shah, et al. Standards Track [Page 27] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + All other values are Unassigned and available to IANA for assignment. + New RDMAP Message Atomic Operation Subcodes should be assigned + sequentially in order to better support implementations that process + RDMAP Message Atomic Operations in hardware. + + Allocation Policy: Standards Action [RFC5226] + +10.2. RDMAP Queue Numbers + + Name of the registry: "RDMAP DDP Untagged Queue Numbers" + + Namespace details: RDMAP DDP Untagged Queue numbers are 32-bit + values. + + Information that must be provided to assign a new value: An IESG- + approved Standards Track specification defining the semantics and + interoperability requirements of the proposed new value and the + fields to be recorded in the registry. + + Fields to record in the registry: RDMAP DDP Untagged Queue Numbers, + Queue Usage Description, RFC Reference. + + Initial registry contents: + + 0x00000000, Queue 0 (Send operation Variants), [RFC5040] + + 0x00000001, Queue 1 (RDMA Read Request operations), [RFC5040] + + 0x00000002, Queue 2 (Terminate operations), [RFC5040] + + 0x00000003, Queue 3 (Atomic Response operations), this specification + + Note: An experimental RDMAP Message Operation Code has already been + allocated; hence, there is no need for an experimental RDMAP DDP + Untagged Queue Number. + + All other values are Unassigned and available to IANA for assignment. + New RDMAP queue numbers should be assigned sequentially in order to + better support implementations that perform RDMAP queue selection in + hardware. + + Allocation Policy: Standards Action [RFC5226] + + + + + + + + + +Shah, et al. Standards Track [Page 28] + +RFC 7306 RDMA Protocol Extensions June 2014 + + +11. References + +11.1. Normative References + + [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate + Requirement Levels", BCP 14, RFC 2119, March 1997. + + [RFC4303] Kent, S., "IP Encapsulating Security Payload (ESP)", RFC + 4303, December 2005. + + [RFC5040] Recio, R., Metzler, B., Culley, P., Hilland, J., and D. + Garcia, "A Remote Direct Memory Access Protocol + Specification", RFC 5040, October 2007. + + [RFC5041] Shah, H., Pinkerton, J., Recio, R., and P. Culley, "Direct + Data Placement over Reliable Transports", RFC 5041, + October 2007. + + [RFC5042] Pinkerton, J. and E. Deleganes, "Direct Data Placement + Protocol (DDP) / Remote Direct Memory Access Protocol + (RDMAP) Security", RFC 5042, October 2007. + + [RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an + IANA Considerations Section in RFCs", BCP 26, RFC 5226, + May 2008. + + [RFC7146] Black, D. and P. Koning, "Securing Block Storage Protocols + over IP: RFC 3723 Requirements Update for IPsec v3", RFC + 7146, April 2014. + +11.2. Informative References + + [DAT_ATOMICS] + DAT Collaborative, "IB Transport Specific Extensions for + DAT 2.0", User Direct Access Programming Library, + . + + [IB] InfiniBand Trade Association, "InfiniBand Architecture + Specification Volumes 1 and 2", Release 1.1, November + 2002, . + + [MPI] Message Passing Interface Forum, "MPI: A Message-Passing + Interface Standard, Version 3.0", September 2012, + . + + + + + + + +Shah, et al. Standards Track [Page 29] + +RFC 7306 RDMA Protocol Extensions June 2014 + + + [OFAVERBS] Rosenstock, H., "Subject: Re: [PATCH 0/2] Add support for + enhanced atomic operations", message to the linux-rdma + mailing list, + . + + [RFC5044] Culley, P., Elzur, U., Recio, R., Bailey, S., and J. + Carrier, "Marker PDU Aligned Framing for TCP + Specification", RFC 5044, October 2007. + + [RFC5045] Bestler, C., Ed., and L. Coene, "Applicability of Remote + Direct Memory Access Protocol (RDMA) and Direct Data + Placement (DDP)", RFC 5045, October 2007. + + [RFC6581] Kanevsky, A., Ed., Bestler, C., Ed., Sharp, R., and S. + Wise, "Enhanced Remote Direct Memory Access (RDMA) + Connection Establishment", RFC 6581, April 2012. + + [RSOCKETS] Hefty, S., "RDMA CM - RDMA enabled Sockets library for + Open Fabrics", . + +12. Acknowledgments + + The authors would like to acknowledge the following individuals who + provided valuable comments and suggestions. + + o David Black + + o Arkady Kanevsky + + o Bernard Metzler + + o Jim Pinkerton + + o Tom Talpey + + o Steve Wise + + o Don Wood + + + + + + + + + + + + +Shah, et al. Standards Track [Page 30] + +RFC 7306 RDMA Protocol Extensions June 2014 + + +Appendix A. DDP Segment Formats for RDMA Messages + + This appendix is for information only and is NOT part of the + standard. It simply depicts the DDP Segment format for the various + RDMA Messages. + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +Shah, et al. Standards Track [Page 31] + +RFC 7306 RDMA Protocol Extensions June 2014 + + +A.1. DDP Segment for Atomic Operation Request + + The following figure depicts an Atomic Operation Request, DDP + Segment: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | DDP Control | RDMA Control | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Reserved (Not Used) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | DDP (Atomic Operation Request) Queue Number | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | DDP (Atomic Operation Request) Message Sequence Number | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | DDP (Atomic Operation Request) Message Offset | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Reserved (Not Used) |AOpCode| + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Request Identifier | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Remote STag | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Remote Tagged Offset | + + + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Add or Swap Data | + + + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Add or Swap Mask | + + + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Compare Data | + + + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Compare Mask | + + + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + + + + + + +Shah, et al. Standards Track [Page 32] + +RFC 7306 RDMA Protocol Extensions June 2014 + + +A.2. DDP Segment for Atomic Response + + The following figure depicts an Atomic Operation Response, DDP + Segment: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | DDP Control | RDMA Control | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Reserved (Not Used) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | DDP (Atomic Operation Request) Queue Number | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | DDP (Atomic Operation Request) Message Sequence Number | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | DDP (Atomic Operation Request) Message Offset | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Original Request Identifier | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Original Remote Value | + + + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + +A.3. DDP Segment for Immediate Data and Immediate Data with SE + + The following figure depicts an Immediate Data or Immediate Data with + SE, DDP Segment: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | DDP Control | RDMA Control | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Reserved (Not Used) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | DDP (Send) Queue Number | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | DDP (Send) Message Sequence Number | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | DDP Message Offset | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Immediate Data | + + + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + + + +Shah, et al. Standards Track [Page 33] + +RFC 7306 RDMA Protocol Extensions June 2014 + + +Authors' Addresses + + Hemal Shah + Broadcom Corporation + 5300 California Avenue + Irvine, CA 92617 + US + Phone: 1-949-926-6941 + EMail: hemal@broadcom.com + + + Felix Marti + Chelsio Communications, Inc. + 370 San Aleso Ave. + Sunnyvale, CA 94085 + US + Phone: 1-408-962-3600 + EMail: felix@chelsio.com + + + Asgeir Eiriksson + Chelsio Communications, Inc. + 370 San Aleso Ave. + Sunnyvale, CA 94085 + US + Phone: 1-408-962-3600 + EMail: asgeir@chelsio.com + + + Wael Noureddine + Chelsio Communications, Inc. + 370 San Aleso Ave. + Sunnyvale, CA 94085 + US + Phone: 1-408-962-3600 + EMail: wael@chelsio.com + + + Robert Sharp + Intel Corporation + 1300 South Mopac Expy, Mailstop: AN4-4B + Austin, TX 78746 + US + Phone: 1-512-362-1407 + EMail: robert.o.sharp@intel.com + + + + + + +Shah, et al. Standards Track [Page 34] + -- cgit v1.2.3