From 4bfd864f10b68b71482b35c818559068ef8d5797 Mon Sep 17 00:00:00 2001 From: Thomas Voss Date: Wed, 27 Nov 2024 20:54:24 +0100 Subject: doc: Add RFC documents --- doc/rfc/rfc7439.txt | 1571 +++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 1571 insertions(+) create mode 100644 doc/rfc/rfc7439.txt (limited to 'doc/rfc/rfc7439.txt') diff --git a/doc/rfc/rfc7439.txt b/doc/rfc/rfc7439.txt new file mode 100644 index 0000000..93a7a0c --- /dev/null +++ b/doc/rfc/rfc7439.txt @@ -0,0 +1,1571 @@ + + + + + + +Internet Engineering Task Force (IETF) W. George, Ed. +Request for Comments: 7439 Time Warner Cable +Category: Informational C. Pignataro, Ed. +ISSN: 2070-1721 Cisco + January 2015 + + + Gap Analysis for Operating IPv6-Only MPLS Networks + +Abstract + + This document reviews the Multiprotocol Label Switching (MPLS) + protocol suite in the context of IPv6 and identifies gaps that must + be addressed in order to allow MPLS-related protocols and + applications to be used with IPv6-only networks. This document is + intended to focus on gaps in the standards defining the MPLS suite, + and is not intended to highlight particular vendor implementations + (or lack thereof) in the context of IPv6-only MPLS functionality. + + In the data plane, MPLS fully supports IPv6, and MPLS labeled packets + can be carried over IPv6 packets in a variety of encapsulations. + However, support for IPv6 among MPLS control-plane protocols, MPLS + applications, MPLS Operations, Administration, and Maintenance (OAM), + and MIB modules is mixed, with some protocols having major gaps. For + most major gaps, work is in progress to upgrade the relevant + protocols. + +Status of This Memo + + This document is not an Internet Standards Track specification; it is + published for informational purposes. + + This document is a product of the Internet Engineering Task Force + (IETF). It represents the consensus of the IETF community. It has + received public review and has been approved for publication by the + Internet Engineering Steering Group (IESG). Not all documents + approved by the IESG are a candidate for any level of Internet + Standard; see Section 2 of RFC 5741. + + Information about the current status of this document, any errata, + and how to provide feedback on it may be obtained at + http://www.rfc-editor.org/info/rfc7439. + + + + + + + + + +George & Pignataro Informational [Page 1] + +RFC 7439 IPv6-Only MPLS January 2015 + + +Copyright Notice + + Copyright (c) 2015 IETF Trust and the persons identified as the + document authors. All rights reserved. + + This document is subject to BCP 78 and the IETF Trust's Legal + Provisions Relating to IETF Documents + (http://trustee.ietf.org/license-info) in effect on the date of + publication of this document. Please review these documents + carefully, as they describe your rights and restrictions with respect + to this document. Code Components extracted from this document must + include Simplified BSD License text as described in Section 4.e of + the Trust Legal Provisions and are provided without warranty as + described in the Simplified BSD License. + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +George & Pignataro Informational [Page 2] + +RFC 7439 IPv6-Only MPLS January 2015 + + +Table of Contents + + 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4 + 2. Use Case . . . . . . . . . . . . . . . . . . . . . . . . . . 4 + 3. Gap Analysis . . . . . . . . . . . . . . . . . . . . . . . . 5 + 3.1. MPLS Data Plane . . . . . . . . . . . . . . . . . . . . . 6 + 3.2. MPLS Control Plane . . . . . . . . . . . . . . . . . . . 6 + 3.2.1. Label Distribution Protocol (LDP) . . . . . . . . . . 6 + 3.2.2. Multipoint LDP (mLDP) . . . . . . . . . . . . . . . . 6 + 3.2.3. RSVP - Traffic Engineering (RSVP-TE) . . . . . . . . 7 + 3.2.3.1. Interior Gateway Protocol (IGP) . . . . . . . . . 8 + 3.2.3.2. RSVP-TE Point-to-Multipoint (P2MP) . . . . . . . 8 + 3.2.3.3. RSVP-TE Fast Reroute (FRR) . . . . . . . . . . . 8 + 3.2.4. Path Computation Element (PCE) . . . . . . . . . . . 8 + 3.2.5. Border Gateway Protocol (BGP) . . . . . . . . . . . . 9 + 3.2.6. Generalized Multi-Protocol Label Switching (GMPLS) . 9 + 3.3. MPLS Applications . . . . . . . . . . . . . . . . . . . . 9 + 3.3.1. Layer 2 Virtual Private Network (L2VPN) . . . . . . . 9 + 3.3.1.1. Ethernet VPN (EVPN) . . . . . . . . . . . . . . . 10 + 3.3.2. Layer 3 Virtual Private Network (L3VPN) . . . . . . . 10 + 3.3.2.1. IPv6 Provider Edge/IPv4 Provider Edge (6PE/4PE) . 11 + 3.3.2.2. IPv6 Virtual Private Extension/IPv4 Virtual + Private Extension (6VPE/4VPE) . . . . . . . . . . 11 + 3.3.2.3. BGP Encapsulation Subsequent Address Family + Identifier (SAFI) . . . . . . . . . . . . . . . . 12 + 3.3.2.4. Multicast in MPLS/BGP IP VPN (MVPN) . . . . . . . 12 + 3.3.3. MPLS Transport Profile (MPLS-TP) . . . . . . . . . . 13 + 3.4. MPLS Operations, Administration, and Maintenance (MPLS + OAM) . . . . . . . . . . . . . . . . . . . . . . . . . . 13 + 3.4.1. Extended ICMP . . . . . . . . . . . . . . . . . . . . 14 + 3.4.2. Label Switched Path Ping (LSP Ping) . . . . . . . . . 15 + 3.4.3. Bidirectional Forwarding Detection (BFD) . . . . . . 16 + 3.4.4. Pseudowire OAM . . . . . . . . . . . . . . . . . . . 16 + 3.4.5. MPLS Transport Profile (MPLS-TP) OAM . . . . . . . . 16 + 3.5. MIB Modules . . . . . . . . . . . . . . . . . . . . . . . 17 + 4. Gap Summary . . . . . . . . . . . . . . . . . . . . . . . . . 17 + 5. Security Considerations . . . . . . . . . . . . . . . . . . . 18 + 6. References . . . . . . . . . . . . . . . . . . . . . . . . . 19 + 6.1. Normative References . . . . . . . . . . . . . . . . . . 19 + 6.2. Informative References . . . . . . . . . . . . . . . . . 20 + Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . 26 + Contributors . . . . . . . . . . . . . . . . . . . . . . . . . . 26 + Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 28 + + + + + + + + +George & Pignataro Informational [Page 3] + +RFC 7439 IPv6-Only MPLS January 2015 + + +1. Introduction + + IPv6 [RFC2460] is an integral part of modern network deployments. At + the time when this document was written, the majority of these IPv6 + deployments were using dual-stack implementations, where IPv4 and + IPv6 are supported equally on many or all of the network nodes, and + single-stack primarily referred to IPv4-only devices. Dual-stack + deployments provide a useful margin for protocols and features that + are not currently capable of operating solely over IPv6, because they + can continue using IPv4 as necessary. However, as IPv6 deployment + and usage becomes more pervasive, and IPv4 exhaustion begins driving + changes in address consumption behaviors, there is an increasing + likelihood that many networks will need to start operating some or + all of their network nodes either as primarily IPv6 (most functions + use IPv6, a few legacy features use IPv4), or as IPv6-only (no IPv4 + provisioned on the device). This transition toward IPv6-only + operation exposes any gaps where features, protocols, or + implementations are still reliant on IPv4 for proper function. To + that end, and in the spirit of the recommendation in RFC 6540 + [RFC6540] that implementations need to stop requiring IPv4 for proper + and complete function, this document reviews the MPLS protocol suite + in the context of IPv6 and identifies gaps that must be addressed in + order to allow MPLS-related protocols and applications to be used + with IPv6-only networks and networks that are primarily IPv6 + (hereafter referred to as IPv6-primary). This document is intended + to focus on gaps in the standards defining the MPLS suite, and not to + highlight particular vendor implementations (or lack thereof) in the + context of IPv6-only MPLS functionality. + +2. Use Case + + This section discusses some drivers for ensuring that MPLS completely + supports IPv6-only operation. It is not intended to be a + comprehensive discussion of all potential use cases, but rather a + discussion of one use case to provide context and justification to + undertake such a gap analysis. + + IP convergence is continuing to drive new classes of devices to begin + communicating via IP. Examples of such devices could include set-top + boxes for IP video distribution, cell tower electronics (macro or + micro cells), infrastructure Wi-Fi access points, and devices for + machine-to-machine (M2M) or Internet of Things (IoT) applications. + In some cases, these classes of devices represent a very large + deployment base, on the order of thousands or even millions of + devices network-wide. The scale of these networks, coupled with the + increasingly overlapping use of RFC 1918 [RFC1918] address space + within the average network and the lack of globally routable IPv4 + space available for long-term growth, begins to drive the need for + + + +George & Pignataro Informational [Page 4] + +RFC 7439 IPv6-Only MPLS January 2015 + + + many of the endpoints in this network to be managed solely via IPv6. + Even if these devices are carrying some IPv4 user data, it is often + encapsulated in another protocol such that the communication between + the endpoint and its upstream devices can be IPv6-only without + impacting support for IPv4 on user data. As the number of devices to + manage increases, the operator is compelled to move to IPv6. + Depending on the MPLS features required, it is plausible to assume + that the (existing) MPLS network will need to be extended to these + IPv6-only devices. + + Additionally, as the impact of IPv4 exhaustion becomes more acute, + more and more aggressive IPv4 address reclamation measures will be + justified. Many networks are likely to focus on preserving their + remaining IPv4 addresses for revenue-generating customers so that + legacy support for IPv4 can be maintained as long as necessary. As a + result, it may be appropriate for some or all of the network + infrastructure, including MPLS Label Switching Routers (LSRs) and + Label Edge Routers (LERs), to have its IPv4 addresses reclaimed and + transition toward IPv6-only operation. + +3. Gap Analysis + + This gap analysis aims to answer the question of what fails when one + attempts to use MPLS features on a network of IPv6-only devices. The + baseline assumption for this analysis is that some endpoints, as well + as Label Switching Routers (Provider Edge (PE) and Provider (P) + routers), only have IPv6 transport available and need to support the + full suite of MPLS features defined as of the time of this document's + writing at parity with the support on an IPv4 network. This is + necessary whether they are enabled via the Label Distribution + Protocol (LDP) [RFC5036], RSVP - Traffic Engineering (RSVP-TE) + [RFC3209], or Border Gateway Protocol (BGP) [RFC3107], and whether + they are encapsulated in MPLS [RFC3032], IP [RFC4023], Generic + Routing Encapsulation (GRE) [RFC4023], or Layer 2 Tunneling Protocol + Version 3 (L2TPv3) [RFC4817]. It is important when evaluating these + gaps to distinguish between user data and control-plane data, because + while this document is focused on IPv6-only operation, it is quite + likely that some amount of the user payload data being carried in the + IPv6-only MPLS network will still be IPv4. + + A note about terminology: Gaps identified by this document are + characterized as "Major" or "Minor". Major gaps refer to significant + changes necessary in one or more standards to address the gap due to + existing standards language having either missing functionality for + IPv6-only operation or explicit language requiring the use of IPv4 + with no IPv6 alternatives defined. Minor gaps refer to changes + necessary primarily to clarify existing standards language. Usually + + + + +George & Pignataro Informational [Page 5] + +RFC 7439 IPv6-Only MPLS January 2015 + + + these changes are needed in order to explicitly codify IPv6 support + in places where it is either implicit or omitted today, but the + omission is unlikely to prevent IPv6-only operation. + +3.1. MPLS Data Plane + + MPLS labeled packets can be transmitted over a variety of data links + [RFC3032], and MPLS labeled packets can also be encapsulated over IP. + The encapsulations of MPLS in IP and GRE, as well as MPLS over + L2TPv3, support IPv6. See Section 3 of RFC 4023 [RFC4023] and + Section 2 of RFC 4817 [RFC4817], respectively. + + Gap: None. + +3.2. MPLS Control Plane + +3.2.1. Label Distribution Protocol (LDP) + + The Label Distribution Protocol (LDP) [RFC5036] defines a set of + procedures for distribution of labels between Label Switching Routers + that can use the labels for forwarding traffic. While LDP was + designed to use an IPv4 or dual-stack IP network, it has a number of + deficiencies that prevent it from working in an IPv6-only network. + LDP-IPv6 [LDP-IPv6] highlights some of the deficiencies when LDP is + enabled in IPv6-only or dual-stack networks and specifies appropriate + protocol changes. These deficiencies are related to Label Switched + Path (LSP) mapping, LDP identifiers, LDP discovery, LDP session + establishment, next-hop address, and LDP Time To Live (TTL) security + [RFC5082] [RFC6720]. + + Gap: Major; update to RFC 5036 in progress via [LDP-IPv6], which + should close this gap. + +3.2.2. Multipoint LDP (mLDP) + + Multipoint LDP (mLDP) is a set of extensions to LDP for setting up + Point-to-Multipoint (P2MP) and Multipoint-to-Multipoint (MP2MP) LSPs. + These extensions are specified in RFC 6388 [RFC6388]. In terms of + IPv6-only gap analysis, mLDP has two identified areas of interest: + + 1. LDP Control Plane: Since mLDP uses the LDP control plane to + discover and establish sessions with the peer, it shares the same + gaps as LDP (Section 3.2.1) with regards to control plane + (discovery, transport, and session establishment) in an IPv6-only + network. + + + + + + +George & Pignataro Informational [Page 6] + +RFC 7439 IPv6-Only MPLS January 2015 + + + 2. Multipoint (MP) Forwarding Equivalence Class (FEC) Root Address: + mLDP defines its own MP FECs and rules, different from LDP, to + map MP LSPs. An mLDP MP FEC contains a Root Address field that + is an IP address in IP networks. The current specification + allows specifying the root address according to the Address + Family Identifier (AFI), and hence covers both IPv4 or IPv6 root + addresses, requiring no extension to support IPv6-only MP LSPs. + The root address is used by each LSR participating in an MP LSP + setup such that root address reachability is resolved by doing a + table lookup against the root address to find corresponding + upstream neighbor(s). This will pose a problem if an MP LSP + traverses IPv4-only and IPv6-only nodes in a dual-stack network + on the way to the root node. + + For example, consider following setup, where R1/R6 are IPv4-only, R3/ + R4 are IPv6-only, and R2/R5 are dual-stack LSRs: + + ( IPv4-only ) ( IPv6-only ) ( IPv4-only ) + R1 -- R2 -- R3 -- R4 -- R5 -- R6 + Leaf Root + + Assume R1 to be a leaf node for a P2MP LSP rooted at R6 (root node). + R1 uses R6's IPv4 address as the root address in MP FEC. As the MP + LSP signaling proceeds from R1 to R6, the MP LSP setup will fail on + the first IPv6-only transit/branch LSRs (R3) when trying to find IPv4 + root address reachability. RFC 6512 [RFC6512] defines a recursive- + FEC solution and procedures for mLDP when the backbone (transit/ + branch) LSRs have no route to the root. The proposed solution is + defined for a BGP-free core in a VPN environment, but a similar + concept can be used/extended to solve the above issue of the + IPv6-only backbone receiving an MP FEC element with an IPv4 address. + The solution will require a border LSR (the one that is sitting on + the border of an IPv4/IPv6 island (namely, R2 and R5 in this + example)) to translate an IPv4 root address to an equivalent IPv6 + address (and vice versa) through procedures similar to RFC 6512. + + Gap: Major; update in progress for LDP via [LDP-IPv6], may need + additional updates to RFC 6512. + +3.2.3. RSVP - Traffic Engineering (RSVP-TE) + + RSVP-TE [RFC3209] defines a set of procedures and enhancements to + establish LSP tunnels that can be automatically routed away from + network failures, congestion, and bottlenecks. RSVP-TE allows + establishing an LSP for an IPv4 or IPv6 prefix, thanks to its + LSP_TUNNEL_IPv6 object and subobjects. + + Gap: None. + + + +George & Pignataro Informational [Page 7] + +RFC 7439 IPv6-Only MPLS January 2015 + + +3.2.3.1. Interior Gateway Protocol (IGP) + + RFC 3630 [RFC3630] specifies a method of adding traffic engineering + capabilities to OSPF Version 2. New TLVs and sub-TLVs were added in + RFC 5329 [RFC5329] to extend TE capabilities to IPv6 networks in OSPF + Version 3. + + RFC 5305 [RFC5305] specifies a method of adding traffic engineering + capabilities to IS-IS. New TLVs and sub-TLVs were added in RFC 6119 + [RFC6119] to extend TE capabilities to IPv6 networks. + + Gap: None. + +3.2.3.2. RSVP-TE Point-to-Multipoint (P2MP) + + RFC 4875 [RFC4875] describes extensions to RSVP-TE for the setup of + Point-to-Multipoint (P2MP) LSPs in MPLS and Generalized MPLS (GMPLS) + with support for both IPv4 and IPv6. + + Gap: None. + +3.2.3.3. RSVP-TE Fast Reroute (FRR) + + RFC 4090 [RFC4090] specifies Fast Reroute (FRR) mechanisms to + establish backup LSP tunnels for local repair supporting both IPv4 + and IPv6 networks. Further, [RFC5286] describes the use of loop-free + alternates to provide local protection for unicast traffic in pure IP + and MPLS networks in the event of a single failure, whether link, + node, or shared risk link group (SRLG) for both IPv4 and IPv6. + + Gap: None. + +3.2.4. Path Computation Element (PCE) + + The Path Computation Element (PCE) defined in RFC 4655 [RFC4655] is + an entity that is capable of computing a network path or route based + on a network graph and applying computational constraints. A Path + Computation Client (PCC) may make requests to a PCE for paths to be + computed. The PCE Communication Protocol (PCEP) is designed as a + communication protocol between PCCs and PCEs for path computations + and is defined in RFC 5440 [RFC5440]. + + The PCEP specification [RFC5440] is defined for both IPv4 and IPv6 + with support for PCE discovery via an IGP (OSPF [RFC5088] or IS-IS + [RFC5089]) using both IPv4 and IPv6 addresses. Note that PCEP uses + identical encoding of subobjects, as in RSVP-TE defined in RFC 3209 + [RFC3209] that supports both IPv4 and IPv6. + + + + +George & Pignataro Informational [Page 8] + +RFC 7439 IPv6-Only MPLS January 2015 + + + The extensions to PCEP to support confidentiality [RFC5520], route + exclusions [RFC5521], monitoring [RFC5886], and P2MP TE LSPs + [RFC6006] have support for both IPv4 and IPv6. + + Gap: None. + +3.2.5. Border Gateway Protocol (BGP) + + RFC 3107 [RFC3107] specifies a set of BGP protocol procedures for + distributing the labels (for prefixes corresponding to any address + family) between label switch routers so that they can use the labels + for forwarding the traffic. RFC 3107 allows BGP to distribute the + label for IPv4 or IPv6 prefix in an IPv6-only network. + + Gap: None. + +3.2.6. Generalized Multi-Protocol Label Switching (GMPLS) + + The Generalized Multi-Protocol Label Switching (GMPLS) specification + includes signaling functional extensions [RFC3471] and RSVP-TE + extensions [RFC3473]. The gap analysis in Section 3.2.3 applies to + these. + + RFC 4558 [RFC4558] specifies Node-ID Based RSVP Hello Messages with + capability for both IPv4 and IPv6. RFC 4990 [RFC4990] clarifies the + use of IPv6 addresses in GMPLS networks including handling in the MIB + modules. + + The second paragraph of Section 5.3 of RFC 6370 [RFC6370] describes + the mapping from an MPLS Transport Profile (MPLS-TP) LSP_ID to RSVP- + TE with an assumption that Node_IDs are derived from valid IPv4 + addresses. This assumption fails in an IPv6-only network, given that + there would not be any IPv4 addresses. + + Gap: Minor; Section 5.3 of RFC 6370 [RFC6370] needs to be updated. + +3.3. MPLS Applications + +3.3.1. Layer 2 Virtual Private Network (L2VPN) + + L2VPN [RFC4664] specifies two fundamentally different kinds of Layer + 2 VPN services that a service provider could offer to a customer: + Virtual Private Wire Service (VPWS) and Virtual Private LAN Service + (VPLS). RFC 4447 [RFC4447] and RFC 4762 [RFC4762] specify the LDP + protocol changes to instantiate VPWS and VPLS services, respectively, + in an MPLS network using LDP as the signaling protocol. This is + complemented by RFC 6074 [RFC6074], which specifies a set of + procedures for instantiating L2VPNs (e.g., VPWS, VPLS) using BGP as a + + + +George & Pignataro Informational [Page 9] + +RFC 7439 IPv6-Only MPLS January 2015 + + + discovery protocol and LDP, as well as L2TPv3, as a signaling + protocol. RFC 4761 [RFC4761] and RFC 6624 [RFC6624] specify BGP + protocol changes to instantiate VPLS and VPWS services in an MPLS + network, using BGP for both discovery and signaling. + + In an IPv6-only MPLS network, use of L2VPN represents a connection of + Layer 2 islands over an IPv6 MPLS core, and very few changes are + necessary to support operation over an IPv6-only network. The L2VPN + signaling protocol is either BGP or LDP in an MPLS network, and both + can run directly over IPv6 core infrastructure as well as IPv6 edge + devices. RFC 6074 [RFC6074] is the only RFC that appears to have a + gap for IPv6-only operation. In its discovery procedures (Sections + 3.2.2 and 6 of RFC 6074 [RFC6074]), it suggests encoding PE IP + addresses in the Virtual Switching Instance ID (VSI-ID), which is + encoded in Network Layer Reachability Information (NLRI) and should + not exceed 12 bytes (to differentiate its AFI/SAFI (Subsequent + Address Family Identifier) encoding from RFC 4761). This means that + a PE IP address cannot be an IPv6 address. Also, in its signaling + procedures (Section 3.2.3 of RFC 6074 [RFC6074]), it suggests + encoding PE_addr in the Source Attachment Individual Identifier + (SAII) and the Target Attachment Individual Identifier (TAII), which + are limited to 32 bits (AII Type=1) at the moment. + + RFC 6073 [RFC6073] defines the new LDP Pseudowire (PW) Switching + Point PE TLV, which supports IPv4 and IPv6. + + Gap: Minor; RFC 6074 needs to be updated. + +3.3.1.1. Ethernet VPN (EVPN) + + Ethernet VPN [EVPN] defines a method for using BGP MPLS-based + Ethernet VPNs. Because it can use functions in LDP and mLDP, as well + as Multicast VPLS [RFC7117], it inherits LDP gaps previously + identified in Section 3.2.1. Once those gaps are resolved, it should + function properly on IPv6-only networks as defined. + + Gap: Major for LDP; update to RFC 5036 in progress via [LDP-IPv6] + that should close this gap (see Section 3.2.1). + +3.3.2. Layer 3 Virtual Private Network (L3VPN) + + RFC 4364 [RFC4364] defines a method by which a Service Provider may + use an IP backbone to provide IP VPNs for its customers. The + following use cases arise in the context of this gap analysis: + + 1. Connecting IPv6 islands over IPv6-only MPLS network + + 2. Connecting IPv4 islands over IPv6-only MPLS network + + + +George & Pignataro Informational [Page 10] + +RFC 7439 IPv6-Only MPLS January 2015 + + + Both use cases require mapping an IP packet to an IPv6-signaled LSP. + RFC 4364 defines Layer 3 Virtual Private Networks (L3VPNs) for + IPv4-only and has references to 32-bit BGP next-hop addresses. RFC + 4659 [RFC4659] adds support for IPv6 on L3VPNs, including 128-bit BGP + next-hop addresses, and discusses operation whether IPv6 is the + payload or the underlying transport address family. However, RFC + 4659 does not formally update RFC 4364, and thus an implementer may + miss this additional set of standards unless it is explicitly + identified independently of the base functionality defined in RFC + 4364. Further, Section 1 of RFC 4659 explicitly identifies use case + 2 as out of scope for the document. + + The authors do not believe that there are any additional issues + encountered when using L2TPv3, RSVP, or GRE (instead of MPLS) as + transport on an IPv6-only network. + + Gap: Major; RFC 4659 needs to be updated to explicitly cover use case + 2 (discussed in further detail below) + +3.3.2.1. IPv6 Provider Edge/IPv4 Provider Edge (6PE/4PE) + + RFC 4798 [RFC4798] defines IPv6 Provider Edge (6PE), which defines + how to interconnect IPv6 islands over a MPLS-enabled IPv4 cloud. + However, use case 2 is doing the opposite, and thus could also be + referred to as IPv4 Provider Edge (4PE). The method to support this + use case is not defined explicitly. To support it, IPv4 edge devices + need to be able to map IPv4 traffic to MPLS IPv6 core LSPs. Also, + the core switches may not understand IPv4 at all, but in some cases + they may need to be able to exchange Labeled IPv4 routes from one + Autonomous System (AS) to a neighboring AS. + + Gap: Major; RFC 4798 covers only the "6PE" case. Use case 2 is + currently not specified in an RFC. + +3.3.2.2. IPv6 Virtual Private Extension/IPv4 Virtual Private Extension + (6VPE/4VPE) + + RFC 4659 [RFC4659] defines IPv6 Virtual Private Network Extension + (6VPE), a method by which a Service Provider may use its packet- + switched backbone to provide Virtual Private Network (VPN) services + for its IPv6 customers. It allows the core network to be MPLS IPv4 + or MPLS IPv6, thus addressing use case 1 above. RFC 4364 should work + as defined for use case 2 above, which could also be referred to as + IPv4 Virtual Private Extension (4VPE), but the RFC explicitly does + not discuss this use and defines it as out of scope. + + Gap: Minor; RFC 4659 needs to be updated to explicitly cover use case + 2. + + + +George & Pignataro Informational [Page 11] + +RFC 7439 IPv6-Only MPLS January 2015 + + +3.3.2.3. BGP Encapsulation Subsequent Address Family Identifier (SAFI) + + RFC 5512 [RFC5512] defines the BGP Encapsulation SAFI and the BGP + Tunnel Encapsulation Attribute, which can be used to signal tunneling + over an IP Core that is using a single address family. This + mechanism supports transport of MPLS (and other protocols) over + Tunnels in an IP core (including an IPv6-only core). In this + context, load balancing can be provided as specified in RFC 5640 + [RFC5640]. + + Gap: None. + +3.3.2.4. Multicast in MPLS/BGP IP VPN (MVPN) + + RFC 6513 [RFC6513] defines the procedure to provide multicast service + over an MPLS VPN backbone for downstream customers. It is sometimes + referred to as Next Generation Multicast VPN (NG-MVPN) The procedure + involves the below set of protocols. + +3.3.2.4.1. PE-CE Multicast Routing Protocol + + RFC 6513 [RFC6513] explains the use of Protocol Independent Multicast + (PIM) as a Provider Edge - Customer Edge (PE-CE) protocol, while + Section 11.1.2 of RFC 6514 [RFC6514] explains the use of mLDP as a + PE-CE protocol. + + The MCAST-VPN NLRI route-type format defined in RFC 6514 [RFC6514] is + not sufficiently covering all scenarios when mLDP is used as a PE-CE + protocol. The issue is explained in Section 2 of [mLDP-NLRI] along + with a new route type that encodes the mLDP FEC in NLRI. + + Further, [PE-CE] defines the use of BGP as a PE-CE protocol. + + Gap: None. + +3.3.2.4.2. P-Tunnel Instantiation + + [RFC6513] explains the use of the below tunnels: + + o RSVP-TE P2MP LSP + + o PIM Tree + + o mLDP P2MP LSP + + o mLDP MP2MP LSP + + o Ingress Replication + + + +George & Pignataro Informational [Page 12] + +RFC 7439 IPv6-Only MPLS January 2015 + + + Gap: Gaps in RSVP-TE P2MP LSP (Section 3.2.3.2) and mLDP + (Section 3.2.2) P2MP and MP2MP LSP are covered in previous sections. + There are no MPLS-specific gaps for PIM Tree or Ingress Replication, + and any protocol-specific gaps not related to MPLS are outside the + scope of this document. + +3.3.2.4.3. PE-PE Multicast Routing Protocol + + Section 3.1 of RFC 6513 [RFC6513] explains the use of PIM as a PE-PE + protocol, while RFC 6514 [RFC6514] explains the use of BGP as a PE-PE + protocol. + + PE-PE multicast routing is not specific to P-tunnels or to MPLS. It + can be PIM or BGP with P-tunnels that are label based or PIM tree + based. Enabling PIM as a PE-PE multicast protocol is equivalent to + running it on a non-MPLS IPv6 network, so there are not any MPLS- + specific considerations and any gaps are applicable for non-MPLS + networks as well. Similarly, BGP only includes the P-Multicast + Service Interface (PMSI) tunnel attribute as a part of the NLRI, + which is inherited from P-tunnel instantiation and considered to be + an opaque value. Any gaps in the control plane (PIM or BGP) will not + be specific to MPLS. + + Gap: Any gaps in PIM or BGP as a PE-PE multicast routing protocol are + not unique to MPLS, and therefore are outside the scope of this + document. It is included for completeness. + +3.3.3. MPLS Transport Profile (MPLS-TP) + + MPLS-TP does not require IP (see Section 2 of RFC 5921 [RFC5921]) and + should not be affected by operation on an IPv6-only network. + Therefore, this is considered out of scope for this document but is + included for completeness. + + Although not required, MPLS-TP can use IP. One such example is + included in Section 3.2.6, where MPLS-TP identifiers can be derived + from valid IPv4 addresses. + + Gap: None. MPLS-TP does not require IP. + +3.4. MPLS Operations, Administration, and Maintenance (MPLS OAM) + + For MPLS LSPs, there are primarily three OAM mechanisms: Extended + ICMP [RFC4884] [RFC4950], LSP Ping [RFC4379], and Bidirectional + Forwarding Detection (BFD) for MPLS LSPs [RFC5884]. For MPLS + Pseudowires, there is also Virtual Circuit Connectivity Verification + (VCCV) [RFC5085] [RFC5885]. Most of these mechanisms work in pure + + + + +George & Pignataro Informational [Page 13] + +RFC 7439 IPv6-Only MPLS January 2015 + + + IPv6 environments, but there are some problems encountered in mixed + environments due to address-family mismatches. The next subsections + cover these gaps in detail. + + Gap: Major; RFC 4379 needs to be updated to better support multipath + IPv6. Additionally, there is potential for dropped messages in + Extended ICMP and LSP Ping due to IP version mismatches. It is + important to note that this is a more generic problem with tunneling + when address-family mismatches exist and is not specific to MPLS. + While MPLS will be affected, it will be difficult to fix this problem + specifically for MPLS, rather than fixing the more generic problem. + +3.4.1. Extended ICMP + + Extended ICMP to support Multi-part messages is defined in RFC 4884 + [RFC4884]. This extensibility is defined generally for both ICMPv4 + and ICMPv6. The specific ICMP extensions for MPLS are defined in RFC + 4950 [RFC4950]. ICMP Multi-part with MPLS extensions works for IPv4 + and IPv6. However, the mechanisms described in RFC 4884 and 4950 may + fail when tunneling IPv4 traffic over an LSP that is supported by an + IPv6-only infrastructure. + + Assume the following: + + o The path between two IPv4-only hosts contains an MPLS LSP. + + o The two routers that terminate the LSP run dual stack. + + o The LSP interior routers run IPv6 only. + + o The LSP is signaled over IPv6. + + Now assume that one of the hosts sends an IPv4 packet to the other. + However, the packet's TTL expires on an LSP interior router. + According to RFC 3032 [RFC3032], the interior router should examine + the IPv4 payload, format an ICMPv4 message, and send it (over the + tunnel upon which the original packet arrived) to the egress LSP. In + this case, however, the LSP interior router is not IPv4-aware. It + cannot parse the original IPv4 datagram, nor can it send an IPv4 + message. So, no ICMP message is delivered to the source. Some + specific ICMP extensions, in particular, ICMP extensions for + interface and next-hop identification [RFC5837], restrict the address + family of address information included in an Interface Information + Object to the same one as the ICMP (see Section 4.5 of RFC 5837). + While these extensions are not MPLS specific, they can be used with + MPLS packets carrying IP datagrams. This has no implications for + IPv6-only environments. + + + + +George & Pignataro Informational [Page 14] + +RFC 7439 IPv6-Only MPLS January 2015 + + + Gap: Major; IP version mismatches may cause dropped messages. + However, as noted in the previous section, this problem is not + specific to MPLS. + +3.4.2. Label Switched Path Ping (LSP Ping) + + The LSP Ping mechanism defined in RFC 4379 [RFC4379] is specified to + work with IPv6. Specifically, the Target FEC Stacks include both + IPv4 and IPv6 versions of all FECs (see Section 3.2 of RFC 4379). + The only exceptions are the Pseudowire FECs, which are later + specified for IPv6 in RFC 6829 [RFC6829]. The multipath information + also includes IPv6 encodings (see Section 3.3.1 of RFC 4379). + + LSP Ping packets are UDP packets over either IPv4 or IPv6 (see + Section 4.3 of RFC 4379). However, for IPv6 the destination IP + address is a (randomly chosen) IPv6 address from the range + 0:0:0:0:0:FFFF:127/104; that is, using an IPv4-mapped IPv6 address. + This is a transitional mechanism that should not bleed into IPv6-only + networks, as [IPv4-MAPPED] explains. The issue is that the MPLS LSP + Ping mechanism needs a range of loopback IP addresses to be used as + destination addresses to exercise Equal Cost Multiple Path (ECMP), + but the IPv6 address architecture specifies a single address + (::1/128) for loopback. A mechanism to achieve this was proposed in + [LOOPBACK-PREFIX]. + + Additionally, RFC 4379 does not define the value to be used in the + IPv6 Router Alert option (RAO). For IPv4 RAO, a value of zero is + used. However, there is no equivalent value for IPv6 RAO. This gap + needs to be fixed to be able to use LSP Ping in IPv6 networks. + Further details on this gap are captured, along with a proposed + solution, in [IPv6-RAO]. + + Another gap is that the mechanisms described in RFC 4379 may fail + when tunneling IPv4 traffic over an LSP that is supported by + IPv6-only infrastructure. + + Assume the following: + + o LSP Ping is operating in traceroute mode over an MPLS LSP. + + o The two routers that terminate the LSP run dual stack. + + o The LSP interior routers run IPv6 only. + + o The LSP is signaled over IPv6. + + + + + + +George & Pignataro Informational [Page 15] + +RFC 7439 IPv6-Only MPLS January 2015 + + + Packets will expire at LSP interior routers. According to RFC 4379, + the interior router must parse the IPv4 Echo Request and then send an + IPv4 Echo Reply. However, the LSP interior router is not IPv4-aware. + It cannot parse the IPv4 Echo Request, nor can it send an IPv4 Echo + Reply. So, no reply is sent. + + The mechanism described in RFC 4379 also does not sufficiently + explain the behavior in certain IPv6-specific scenarios. For + example, RFC 4379 defines the K value as 28 octets when the Address + Family is set to IPv6 Unnumbered, but it doesn't describe how to + carry a 32-bit LSR Router ID in the 128-bit Downstream IP Address + field. + + Gap: Major; LSP Ping uses IPv4-mapped IPv6 addresses. IP version + mismatches may cause dropped messages and unclear mapping from the + LSR Router ID to Downstream IP Address. + +3.4.3. Bidirectional Forwarding Detection (BFD) + + The BFD specification for MPLS LSPs [RFC5884] is defined for IPv4, as + well as IPv6, versions of MPLS FECs (see Section 3.1 of RFC 5884). + Additionally, the BFD packet is encapsulated over UDP and specified + to run over both IPv4 and IPv6 (see Section 7 of RFC 5884). + + Gap: None. + +3.4.4. Pseudowire OAM + + The OAM specifications for MPLS Pseudowires define usage for both + IPv4 and IPv6. Specifically, VCCV [RFC5085] can carry IPv4 or IPv6 + OAM packets (see Sections 5.1.1 and 5.2.1 of RFC 5085), and VCCV for + BFD [RFC5885] also defines an IPv6 encapsulation (see Section 3.2 of + RFC 5885). + + Additionally, for LSP Ping for pseudowires, the Pseudowire FECs are + specified for IPv6 in RFC 6829 [RFC6829]. + + Gap: None. + +3.4.5. MPLS Transport Profile (MPLS-TP) OAM + + As with MPLS-TP, MPLS-TP OAM [RFC6371] does not require IP or + existing MPLS OAM functions and should not be affected by operation + on an IPv6-only network. Therefore, this is out of scope for this + document but is included for completeness. Although not required, + MPLS-TP can use IP. + + Gap: None. MPLS-TP OAM does not require IP. + + + +George & Pignataro Informational [Page 16] + +RFC 7439 IPv6-Only MPLS January 2015 + + +3.5. MIB Modules + + RFC 3811 [RFC3811] defines the textual conventions for MPLS. These + lack support for IPv6 in defining MplsExtendedTunnelId and + MplsLsrIdentifier. These textual conventions are used in the MPLS-TE + MIB specification [RFC3812], the GMPLS-TE MIB specification [RFC4802] + and the FRR extension [RFC6445]. "Definitions of Textual Conventions + (TCs) for Multiprotocol Label Switching (MPLS) Management" [MPLS-TC] + tries to resolve this gap by marking this textual convention as + obsolete. + + The other MIB specifications for LSR [RFC3813], LDP [RFC3815], and TE + [RFC4220] have support for both IPv4 and IPv6. + + Lastly, RFC 4990 [RFC4990] discusses how to handle IPv6 sources and + destinations in the MPLS and GMPLS-TE MIB modules. In particular, + Section 8 of RFC 4990 [RFC4990] describes a method of defining or + monitoring an LSP tunnel using the MPLS-TE and GMPLS-TE MIB modules, + working around some of the limitations in RFC 3811 [RFC3811]. + + Gap: Minor; Section 8 of RFC 4990 [RFC4990] describes a method to + handle IPv6 addresses in the MPLS-TE [RFC3812] and GMPLS-TE [RFC4802] + MIB modules. Work underway to update RFC 3811 via [MPLS-TC], may + also need to update RFC 3812, RFC 4802, and RFC 6445, which depend on + it. + +4. Gap Summary + + This document has reviewed a wide variety of MPLS features and + protocols to determine their suitability for use on IPv6-only or + IPv6-primary networks. While some parts of the MPLS suite will + function properly without additional changes, gaps have been + identified in others that will need to be addressed with follow-on + work. This section will summarize those gaps, along with pointers to + any work in progress to address them. Note that because the + referenced documents are works in progress and do not have consensus + at the time of this document's publication, there could be other + solutions proposed at a future time, and the pointers in this + document should not be considered normative in any way. + Additionally, work in progress on new features that use MPLS + protocols will need to ensure that those protocols support operation + on IPv6-only or IPv6-primary networks, or explicitly identify any + dependencies on existing gaps that, once resolved, will allow proper + IPv6-only operation. + + + + + + + +George & Pignataro Informational [Page 17] + +RFC 7439 IPv6-Only MPLS January 2015 + + + Identified Gaps in MPLS for IPv6-Only Networks + + +---------+---------------------------------------+-----------------+ + | Item | Gap | Addressed in | + +---------+---------------------------------------+-----------------+ + | LDP | LSP mapping, LDP identifiers, LDP | [LDP-IPv6] | + | S.3.2.1 | discovery, LDP session establishment, | | + | | next-hop address, and LDP TTL | | + | | security | | + +---------+---------------------------------------+-----------------+ + | mLDP | Inherits gaps from LDP, RFC 6512 | Inherits | + | S.3.2.2 | [RFC6512] | [LDP-IPv6], | + | | | additional | + | | | fixes TBD | + +---------+---------------------------------------+-----------------+ + | GMPLS | RFC 6370 [RFC6370] Node ID derivation | TBD | + | S.3.2.6 | | | + +---------+---------------------------------------+-----------------+ + | L2VPN | RFC 6074 [RFC6074] discovery, | TBD | + | S.3.3.1 | signaling | | + +---------+---------------------------------------+-----------------+ + | L3VPN | RFC 4659 [RFC4659] does not define a | TBD | + | S.3.3.2 | method for 4PE/4VPE | | + +---------+---------------------------------------+-----------------+ + | OAM | RFC 4379 [RFC4379] No IPv6 multipath | [IPv6-RAO] | + | S.3.4 | support, no IPv6 RAO, possible | | + | | dropped messages in IP version | | + | | mismatch | | + +---------+---------------------------------------+-----------------+ + | MIB | RFC 3811 [RFC3811] no IPv6 textual | [MPLS-TC] | + | Modules | convention | | + | S.3.5 | | | + +---------+---------------------------------------+-----------------+ + + Table 1: IPv6-Only MPLS Gaps + +5. Security Considerations + + Changing the address family used for MPLS network operation does not + fundamentally alter the security considerations currently extant in + any of the specifics of the protocol or its features. However, + follow-on work recommended by this gap analysis will need to address + any effects that the use of IPv6 in their modifications may have on + security. + + + + + + + +George & Pignataro Informational [Page 18] + +RFC 7439 IPv6-Only MPLS January 2015 + + +6. References + +6.1. Normative References + + [RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6 + (IPv6) Specification", RFC 2460, December 1998, + . + + [RFC3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., + Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack + Encoding", RFC 3032, January 2001, + . + + [RFC3107] Rekhter, Y. and E. Rosen, "Carrying Label Information in + BGP-4", RFC 3107, May 2001, + . + + [RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V., + and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP + Tunnels", RFC 3209, December 2001, + . + + [RFC3471] Berger, L., "Generalized Multi-Protocol Label Switching + (GMPLS) Signaling Functional Description", RFC 3471, + January 2003, . + + [RFC3473] Berger, L., "Generalized Multi-Protocol Label Switching + (GMPLS) Signaling Resource ReserVation Protocol-Traffic + Engineering (RSVP-TE) Extensions", RFC 3473, January 2003, + . + + [RFC3811] Nadeau, T. and J. Cucchiara, "Definitions of Textual + Conventions (TCs) for Multiprotocol Label Switching (MPLS) + Management", RFC 3811, June 2004, + . + + [RFC4023] Worster, T., Rekhter, Y., and E. Rosen, "Encapsulating + MPLS in IP or Generic Routing Encapsulation (GRE)", RFC + 4023, March 2005, + . + + [RFC4379] Kompella, K. and G. Swallow, "Detecting Multi-Protocol + Label Switched (MPLS) Data Plane Failures", RFC 4379, + February 2006, . + + + + + + + +George & Pignataro Informational [Page 19] + +RFC 7439 IPv6-Only MPLS January 2015 + + + [RFC4659] De Clercq, J., Ooms, D., Carugi, M., and F. Le Faucheur, + "BGP-MPLS IP Virtual Private Network (VPN) Extension for + IPv6 VPN", RFC 4659, September 2006, + . + + [RFC4817] Townsley, M., Pignataro, C., Wainner, S., Seely, T., and + J. Young, "Encapsulation of MPLS over Layer 2 Tunneling + Protocol Version 3", RFC 4817, March 2007, + . + + [RFC5036] Andersson, L., Minei, I., and B. Thomas, "LDP + Specification", RFC 5036, October 2007, + . + + [RFC6074] Rosen, E., Davie, B., Radoaca, V., and W. Luo, + "Provisioning, Auto-Discovery, and Signaling in Layer 2 + Virtual Private Networks (L2VPNs)", RFC 6074, January + 2011, . + + [RFC6370] Bocci, M., Swallow, G., and E. Gray, "MPLS Transport + Profile (MPLS-TP) Identifiers", RFC 6370, September 2011, + . + + [RFC6512] Wijnands, IJ., Rosen, E., Napierala, M., and N. Leymann, + "Using Multipoint LDP When the Backbone Has No Route to + the Root", RFC 6512, February 2012, + . + +6.2. Informative References + + [EVPN] Sajassi, A., Aggarwal, R., Bitar, N., Isaac, A., and J. + Uttaro, "BGP MPLS Based Ethernet VPN", Work in Progress, + draft-ietf-l2vpn-evpn-11, October 2014. + + [IPv4-MAPPED] + Metz, C. and J. Hagino, "IPv4-Mapped Addresses on the Wire + Considered Harmful", Work in Progress, draft-itojun-v6ops- + v4mapped-harmful-02, October 2003. + + [IPv6-RAO] + Raza, K., Akiya, N., and C. Pignataro, "IPv6 Router Alert + Option for MPLS OAM", Work in Progress, draft-raza-mpls- + oam-ipv6-rao-02, September 2014. + + [LDP-IPv6] + Asati, R., Manral, V., Papneja, R., and C. Pignataro, + "Updates to LDP for IPv6", Work in Progress, draft-ietf- + mpls-ldp-ipv6-14, October 2014. + + + +George & Pignataro Informational [Page 20] + +RFC 7439 IPv6-Only MPLS January 2015 + + + [LOOPBACK-PREFIX] + Smith, M., "A Larger Loopback Prefix for IPv6", Work in + Progress, draft-smith-v6ops-larger-ipv6-loopback-prefix- + 04, February 2013. + + [mLDP-NLRI] + Wijnands, I., Rosen, E., and U. Joorde, "Encoding mLDP + FECs in the NLRI of BGP MCAST-VPN Routes", Work in + Progress, draft-ietf-l3vpn-mvpn-mldp-nlri-10, November + 2014. + + [MPLS-TC] Manral, V., Tsou, T., Will, W., and F. Fondelli, + "Definitions of Textual Conventions (TCs) for + Multiprotocol Label Switching (MPLS) Management", Work in + Progress, draft-manral-mpls-rfc3811bis-04, September 2014. + + [PE-CE] Patel, K., Rekhter, Y., and E. Rosen, "BGP as an MVPN + PE-CE Protocol", Work in Progress, + draft-ietf-l3vpn-mvpn-pe- ce-02, October 2014. + + [RFC1918] Rekhter, Y., Moskowitz, R., Karrenberg, D., Groot, G., and + E. Lear, "Address Allocation for Private Internets", + BCP 5, RFC 1918, February 1996, + . + + [RFC3630] Katz, D., Kompella, K., and D. Yeung, "Traffic Engineering + (TE) Extensions to OSPF Version 2", RFC 3630, September + 2003, . + + [RFC3812] Srinivasan, C., Viswanathan, A., and T. Nadeau, + "Multiprotocol Label Switching (MPLS) Traffic Engineering + (TE) Management Information Base (MIB)", RFC 3812, June + 2004, . + + [RFC3813] Srinivasan, C., Viswanathan, A., and T. Nadeau, + "Multiprotocol Label Switching (MPLS) Label Switching + Router (LSR) Management Information Base (MIB)", RFC 3813, + June 2004, . + + [RFC3815] Cucchiara, J., Sjostrand, H., and J. Luciani, "Definitions + of Managed Objects for the Multiprotocol Label Switching + (MPLS), Label Distribution Protocol (LDP)", RFC 3815, June + 2004, . + + [RFC4090] Pan, P., Swallow, G., and A. Atlas, "Fast Reroute + Extensions to RSVP-TE for LSP Tunnels", RFC 4090, May + 2005, . + + + + +George & Pignataro Informational [Page 21] + +RFC 7439 IPv6-Only MPLS January 2015 + + + [RFC4220] Dubuc, M., Nadeau, T., and J. Lang, "Traffic Engineering + Link Management Information Base", RFC 4220, November + 2005, . + + [RFC4364] Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private + Networks (VPNs)", RFC 4364, February 2006, + . + + [RFC4447] Martini, L., Rosen, E., El-Aawar, N., Smith, T., and G. + Heron, "Pseudowire Setup and Maintenance Using the Label + Distribution Protocol (LDP)", RFC 4447, April 2006, + . + + [RFC4558] Ali, Z., Rahman, R., Prairie, D., and D. Papadimitriou, + "Node-ID Based Resource Reservation Protocol (RSVP) Hello: + A Clarification Statement", RFC 4558, June 2006, + . + + [RFC4655] Farrel, A., Vasseur, J., and J. Ash, "A Path Computation + Element (PCE)-Based Architecture", RFC 4655, August 2006, + . + + [RFC4664] Andersson, L. and E. Rosen, "Framework for Layer 2 Virtual + Private Networks (L2VPNs)", RFC 4664, September 2006, + . + + [RFC4761] Kompella, K. and Y. Rekhter, "Virtual Private LAN Service + (VPLS) Using BGP for Auto-Discovery and Signaling", RFC + 4761, January 2007, + . + + [RFC4762] Lasserre, M. and V. Kompella, "Virtual Private LAN Service + (VPLS) Using Label Distribution Protocol (LDP) Signaling", + RFC 4762, January 2007, + . + + [RFC4798] De Clercq, J., Ooms, D., Prevost, S., and F. Le Faucheur, + "Connecting IPv6 Islands over IPv4 MPLS Using IPv6 + Provider Edge Routers (6PE)", RFC 4798, February 2007, + . + + [RFC4802] Nadeau, T. and A. Farrel, "Generalized Multiprotocol Label + Switching (GMPLS) Traffic Engineering Management + Information Base", RFC 4802, February 2007, + . + + + + + + +George & Pignataro Informational [Page 22] + +RFC 7439 IPv6-Only MPLS January 2015 + + + [RFC4875] Aggarwal, R., Papadimitriou, D., and S. Yasukawa, + "Extensions to Resource Reservation Protocol - Traffic + Engineering (RSVP-TE) for Point-to-Multipoint TE Label + Switched Paths (LSPs)", RFC 4875, May 2007, + . + + [RFC4884] Bonica, R., Gan, D., Tappan, D., and C. Pignataro, + "Extended ICMP to Support Multi-Part Messages", RFC 4884, + April 2007, . + + [RFC4950] Bonica, R., Gan, D., Tappan, D., and C. Pignataro, "ICMP + Extensions for Multiprotocol Label Switching", RFC 4950, + August 2007, . + + [RFC4990] Shiomoto, K., Papneja, R., and R. Rabbat, "Use of + Addresses in Generalized Multiprotocol Label Switching + (GMPLS) Networks", RFC 4990, September 2007, + . + + [RFC5082] Gill, V., Heasley, J., Meyer, D., Savola, P., and C. + Pignataro, "The Generalized TTL Security Mechanism + (GTSM)", RFC 5082, October 2007, + . + + [RFC5085] Nadeau, T. and C. Pignataro, "Pseudowire Virtual Circuit + Connectivity Verification (VCCV): A Control Channel for + Pseudowires", RFC 5085, December 2007, + . + + [RFC5088] Le Roux, JL., Vasseur, JP., Ikejiri, Y., and R. Zhang, + "OSPF Protocol Extensions for Path Computation Element + (PCE) Discovery", RFC 5088, January 2008, + . + + [RFC5089] Le Roux, JL., Vasseur, JP., Ikejiri, Y., and R. Zhang, + "IS-IS Protocol Extensions for Path Computation Element + (PCE) Discovery", RFC 5089, January 2008, + . + + [RFC5286] Atlas, A. and A. Zinin, "Basic Specification for IP Fast + Reroute: Loop-Free Alternates", RFC 5286, September 2008, + . + + [RFC5305] Li, T. and H. Smit, "IS-IS Extensions for Traffic + Engineering", RFC 5305, October 2008, + . + + + + + +George & Pignataro Informational [Page 23] + +RFC 7439 IPv6-Only MPLS January 2015 + + + [RFC5329] Ishiguro, K., Manral, V., Davey, A., and A. Lindem, + "Traffic Engineering Extensions to OSPF Version 3", RFC + 5329, September 2008, + . + + [RFC5440] Vasseur, JP. and JL. Le Roux, "Path Computation Element + (PCE) Communication Protocol (PCEP)", RFC 5440, March + 2009, . + + [RFC5512] Mohapatra, P. and E. Rosen, "The BGP Encapsulation + Subsequent Address Family Identifier (SAFI) and the BGP + Tunnel Encapsulation Attribute", RFC 5512, April 2009, + . + + [RFC5520] Bradford, R., Vasseur, JP., and A. Farrel, "Preserving + Topology Confidentiality in Inter-Domain Path Computation + Using a Path-Key-Based Mechanism", RFC 5520, April 2009, + . + + [RFC5521] Oki, E., Takeda, T., and A. Farrel, "Extensions to the + Path Computation Element Communication Protocol (PCEP) for + Route Exclusions", RFC 5521, April 2009, + . + + [RFC5640] Filsfils, C., Mohapatra, P., and C. Pignataro, "Load- + Balancing for Mesh Softwires", RFC 5640, August 2009, + . + + [RFC5837] Atlas, A., Bonica, R., Pignataro, C., Shen, N., and JR. + Rivers, "Extending ICMP for Interface and Next-Hop + Identification", RFC 5837, April 2010, + . + + [RFC5884] Aggarwal, R., Kompella, K., Nadeau, T., and G. Swallow, + "Bidirectional Forwarding Detection (BFD) for MPLS Label + Switched Paths (LSPs)", RFC 5884, June 2010, + . + + [RFC5885] Nadeau, T. and C. Pignataro, "Bidirectional Forwarding + Detection (BFD) for the Pseudowire Virtual Circuit + Connectivity Verification (VCCV)", RFC 5885, June 2010, + . + + [RFC5886] Vasseur, JP., Le Roux, JL., and Y. Ikejiri, "A Set of + Monitoring Tools for Path Computation Element (PCE)-Based + Architecture", RFC 5886, June 2010, + . + + + + +George & Pignataro Informational [Page 24] + +RFC 7439 IPv6-Only MPLS January 2015 + + + [RFC5921] Bocci, M., Bryant, S., Frost, D., Levrau, L., and L. + Berger, "A Framework for MPLS in Transport Networks", + RFC 5921, July 2010, + . + + [RFC6006] Zhao, Q., King, D., Verhaeghe, F., Takeda, T., Ali, Z., + and J. Meuric, "Extensions to the Path Computation Element + Communication Protocol (PCEP) for Point-to-Multipoint + Traffic Engineering Label Switched Paths", RFC 6006, + September 2010, . + + [RFC6073] Martini, L., Metz, C., Nadeau, T., Bocci, M., and M. + Aissaoui, "Segmented Pseudowire", RFC 6073, January 2011, + . + + [RFC6119] Harrison, J., Berger, J., and M. Bartlett, "IPv6 Traffic + Engineering in IS-IS", RFC 6119, February 2011, + . + + [RFC6371] Busi, I. and D. Allan, "Operations, Administration, and + Maintenance Framework for MPLS-Based Transport Networks", + RFC 6371, September 2011, + . + + [RFC6388] Wijnands, IJ., Minei, I., Kompella, K., and B. Thomas, + "Label Distribution Protocol Extensions for Point-to- + Multipoint and Multipoint-to-Multipoint Label Switched + Paths", RFC 6388, November 2011, + . + + [RFC6445] Nadeau, T., Koushik, A., and R. Cetin, "Multiprotocol + Label Switching (MPLS) Traffic Engineering Management + Information Base for Fast Reroute", RFC 6445, November + 2011, . + + [RFC6513] Rosen, E. and R. Aggarwal, "Multicast in MPLS/BGP IP + VPNs", RFC 6513, February 2012, + . + + [RFC6514] Aggarwal, R., Rosen, E., Morin, T., and Y. Rekhter, "BGP + Encodings and Procedures for Multicast in MPLS/BGP IP + VPNs", RFC 6514, February 2012, + . + + [RFC6540] George, W., Donley, C., Liljenstolpe, C., and L. Howard, + "IPv6 Support Required for All IP-Capable Nodes", BCP 177, + RFC 6540, April 2012, + . + + + +George & Pignataro Informational [Page 25] + +RFC 7439 IPv6-Only MPLS January 2015 + + + [RFC6624] Kompella, K., Kothari, B., and R. Cherukuri, "Layer 2 + Virtual Private Networks Using BGP for Auto-Discovery and + Signaling", RFC 6624, May 2012, + . + + [RFC6720] Pignataro, C. and R. Asati, "The Generalized TTL Security + Mechanism (GTSM) for the Label Distribution Protocol + (LDP)", RFC 6720, August 2012, + . + + [RFC6829] Chen, M., Pan, P., Pignataro, C., and R. Asati, "Label + Switched Path (LSP) Ping for Pseudowire Forwarding + Equivalence Classes (FECs) Advertised over IPv6", RFC + 6829, January 2013, + . + + [RFC7117] Aggarwal, R., Kamite, Y., Fang, L., Rekhter, Y., and C. + Kodeboniya, "Multicast in Virtual Private LAN Service + (VPLS)", RFC 7117, February 2014, + . + +Acknowledgements + + The authors wish to thank Alvaro Retana, Andrew Yourtchenko, Loa + Andersson, David Allan, Mach Chen, Mustapha Aissaoui, and Mark Tinka + for their detailed reviews, as well as Brian Haberman, Joel Jaeggli, + Adrian Farrel, Nobo Akiya, Francis Dupont, and Tobias Gondrom for + their comments. + +Contributors + + The following people have contributed text to this document: + + Rajiv Asati + Cisco Systems + 7025 Kit Creek Road + Research Triangle Park, NC 27709 + United States + + EMail: rajiva@cisco.com + + + + + + + + + + + +George & Pignataro Informational [Page 26] + +RFC 7439 IPv6-Only MPLS January 2015 + + + Kamran Raza + Cisco Systems + 2000 Innovation Drive + Ottawa, ON K2K-3E8 + Canada + + EMail: skraza@cisco.com + + + Ronald Bonica + Juniper Networks + 2251 Corporate Park Drive + Herndon, VA 20171 + United States + + EMail: rbonica@juniper.net + + + Rajiv Papneja + Huawei Technologies + 2330 Central Expressway + Santa Clara, CA 95050 + United States + + EMail: rajiv.papneja@huawei.com + + + Dhruv Dhody + Huawei Technologies + Leela Palace + Bangalore, Karnataka 560008 + India + + EMail: dhruv.ietf@gmail.com + + + Vishwas Manral + Ionos Networks + Sunnyvale, CA 94089 + United States + + EMail: vishwas@ionosnetworks.com + + + + + + + + + +George & Pignataro Informational [Page 27] + +RFC 7439 IPv6-Only MPLS January 2015 + + + Nagendra Kumar + Cisco Systems, Inc. + 7200 Kit Creek Road + Research Triangle Park, NC 27709 + United States + + EMail: naikumar@cisco.com + +Authors' Addresses + + Wesley George (editor) + Time Warner Cable + 13820 Sunrise Valley Drive + Herndon, VA 20111 + United States + + Phone: +1-703-561-2540 + EMail: wesley.george@twcable.com + + + Carlos Pignataro (editor) + Cisco Systems, Inc. + 7200-12 Kit Creek Road + Research Triangle Park, NC 27709 + United States + + Phone: +1-919-392-7428 + EMail: cpignata@cisco.com + + + + + + + + + + + + + + + + + + + + + + + +George & Pignataro Informational [Page 28] + -- cgit v1.2.3