path: root/doc/rfc/rfc2481.txt

Network Working Group                                    K. Ramakrishnan
Request for Comments: 2481                            AT&T Labs Research
Category: Experimental                                          S. Floyd
                                                                    LBNL
                                                            January 1999


     A Proposal to add Explicit Congestion Notification (ECN) to IP

Status of this Memo

   This memo defines an Experimental Protocol for the Internet
   community.  It does not specify an Internet standard of any kind.
   Discussion and suggestions for improvement are requested.
   Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (1999).  All Rights Reserved.

Abstract

   This note describes a proposed addition of ECN (Explicit Congestion
   Notification) to IP.  TCP is currently the dominant transport
   protocol used in the Internet. We begin by describing TCP's use of
   packet drops as an indication of congestion.  Next we argue that with
   the addition of active queue management (e.g., RED) to the Internet
   infrastructure, where routers detect congestion before the queue
   overflows, routers are no longer limited to packet drops as an
   indication of congestion.  Routers could instead set a Congestion
   Experienced (CE) bit in the packet header of packets from ECN-capable
   transport protocols.  We describe when the CE bit would be set in the
   routers, and describe what modifications would be needed to TCP to
   make it ECN-capable.  Modifications to other transport protocols
   (e.g., unreliable unicast or multicast, reliable multicast, other
   reliable unicast transport protocols) could be considered as those
   protocols are developed and advance through the standards process.

1.  Conventions and Acronyms

   The keywords MUST, MUST NOT, REQUIRED, SHALL, SHALL NOT, SHOULD,
   SHOULD NOT, RECOMMENDED, MAY, and OPTIONAL, when they appear in this
   document, are to be interpreted as described in [B97].








Ramakrishnan & Floyd          Experimental                      [Page 1]
^L
RFC 2481                       ECN to IP                    January 1999


2. Introduction

   TCP's congestion control and avoidance algorithms are based on the
   notion that the network is a black-box [Jacobson88, Jacobson90].  The
   network's state of congestion or otherwise is determined by end-
   systems probing for the network state, by gradually increasing the
   load on the network (by increasing the window of packets that are
   outstanding in the network) until the network becomes congested and a
   packet is lost.  Treating the network as a "black-box" and treating
   loss as an indication of congestion in the network is appropriate for
   pure best-effort data carried by TCP which has little or no
   sensitivity to delay or loss of individual packets.  In addition,
   TCP's congestion management algorithms have techniques built-in (such
   as Fast Retransmit and Fast Recovery) to minimize the impact of
   losses from a throughput perspective.

   However, these mechanisms are not intended to help applications that
   are in fact sensitive to the delay or loss of one or more individual
   packets.  Interactive traffic such as telnet, web-browsing, and
   transfer of audio and video data can be sensitive to packet losses
   (using an unreliable data delivery transport such as UDP) or to the
   increased latency of the packet caused by the need to retransmit the
   packet after a loss (for reliable data delivery such as TCP).

   Since TCP determines the appropriate congestion window to use by
   gradually increasing the window size until it experiences a dropped
   packet, this causes the queues at the bottleneck router to build up.
   With most packet drop policies at the router that are not sensitive
   to the load placed by each individual flow, this means that some of
   the packets of latency-sensitive flows are going to be dropped.
   Active queue management mechanisms detect congestion before the queue
   overflows, and provide an indication of this congestion to the end
   nodes.  The advantages of active queue management are discussed in
   RFC 2309 [RFC2309].  Active queue management avoids some of the bad
   properties of dropping on queue overflow, including the undesirable
   synchronization of loss across multiple flows.  More importantly,
   active queue management means that transport protocols with
   congestion control (e.g., TCP) do not have to rely on buffer overflow
   as the only indication of congestion.  This can reduce unnecessary
   queueing delay for all traffic sharing that queue.

   Active queue management mechanisms may use one of several methods for
   indicating congestion to end-nodes. One is to use packet drops, as is
   currently done. However, active queue management allows the router to
   separate policies of queueing or dropping packets from the policies
   for indicating congestion. Thus, active queue management allows





Ramakrishnan & Floyd          Experimental                      [Page 2]
^L
RFC 2481                       ECN to IP                    January 1999


   routers to use the Congestion Experienced (CE) bit in a packet header
   as an indication of congestion, instead of relying solely on packet
   drops.

3. Assumptions and General Principles

   In this section, we describe some of the important design principles
   and assumptions that guided the design choices in this proposal.

   (1) Congestion may persist over different time-scales. The time
       scales that we are concerned with are congestion events that may
       last longer than a round-trip time.
   (2) The number of packets in an individual flow (e.g., TCP connection
       or an exchange using UDP) may range from a small number of
       packets to quite a large number. We are interested in managing
       the congestion caused by flows that send enough packets so that
       they are still active when network feedback reaches them.
   (3) New mechanisms for congestion control and avoidance need to co-
       exist and cooperate with existing mechanisms for congestion
       control.  In particular, new mechanisms have to co-exist with
       TCP's current methods of adapting to congestion and with routers'
       current practice of dropping packets in periods of congestion.
   (4) Because ECN is likely to be adopted gradually, accommodating
       migration is essential. Some routers may still only drop packets
       to indicate congestion, and some end-systems may not be ECN-
       capable. The most viable strategy is one that accommodates
       incremental deployment without having to resort to "islands" of
       ECN-capable and non-ECN-capable environments.
   (5) Asymmetric routing is likely to be a normal occurrence in the
       Internet. The path (sequence of links and routers) followed by
       data packets may be different from the path followed by the
       acknowledgment packets in the reverse direction.
   (6) Many routers process the "regular" headers in IP packets more
       efficiently than they process the header information in IP
       options.  This suggests keeping congestion experienced
       information in the regular headers of an IP packet.
   (7) It must be recognized that not all end-systems will cooperate in
       mechanisms for congestion control. However, new mechanisms
       shouldn't make it easier for TCP applications to disable TCP
       congestion control.  The benefit of lying about participating in
       new mechanisms such as ECN-capability should be small.

4. Random Early Detection (RED)

   Random Early Detection (RED) is a mechanism for active queue
   management that has been proposed to detect incipient congestion
   [FJ93], and is currently being deployed in the Internet backbone
   [RFC2309].  Although RED is meant to be a general mechanism using one



Ramakrishnan & Floyd          Experimental                      [Page 3]
^L
RFC 2481                       ECN to IP                    January 1999


   of several alternatives for congestion indication, in the current
   environment of the Internet RED is restricted to using packet drops
   as a mechanism for congestion indication.  RED drops packets based on
   the average queue length exceeding a threshold, rather than only when
   the queue overflows.  However, when RED drops packets before the
   queue actually overflows, RED is not forced by memory limitations to
   discard the packet.

   RED could set a Congestion Experienced (CE) bit in the packet header
   instead of dropping the packet, if such a bit was provided in the IP
   header and understood by the transport protocol.  The use of the CE
   bit would allow the receiver(s) to receive the packet, avoiding the
   potential for excessive delays due to retransmissions after packet
   losses.  We use the term 'CE packet' to denote a packet that has the
   CE bit set.

5. Explicit Congestion Notification in IP

   We propose that the Internet provide a congestion indication for
   incipient congestion (as in RED and earlier work [RJ90]) where the
   notification can sometimes be through marking packets rather than
   dropping them.  This would require an ECN field in the IP header with
   two bits.  The ECN-Capable Transport (ECT) bit would be set by the
   data sender to indicate that the end-points of the transport protocol
   are ECN-capable.  The CE bit would be set by the router to indicate
   congestion to the end nodes.  Routers that have a packet arriving at
   a full queue would drop the packet, just as they do now.

   Bits 6 and 7 in the IPv4 TOS octet are designated as the ECN field.
   Bit 6 is designated as the ECT bit, and bit 7 is designated as the CE
   bit.  The IPv4 TOS octet corresponds to the Traffic Class octet in
   IPv6.  The definitions for the IPv4 TOS octet [RFC791] and the IPv6
   Traffic Class octet are intended to be superseded by the DS
   (Differentiated Services) Field [DIFFSERV].  Bits 6 and 7 are listed
   in [DIFFSERV] as Currently Unused.  Section 19 gives a brief history
   of the TOS octet.

   Because of the unstable history of the TOS octet, the use of the ECN
   field as specified in this document cannot be guaranteed to be
   backwards compatible with all past uses of these two bits.  The
   potential dangers of this lack of backwards compatibility are
   discussed in Section 19.

   Upon the receipt by an ECN-Capable transport of a single CE packet,
   the congestion control algorithms followed at the end-systems MUST be
   essentially the same as the congestion control response to a *single*
   dropped packet.  For example, for ECN-Capable TCP the source TCP is
   required to halve its congestion window for any window of data



Ramakrishnan & Floyd          Experimental                      [Page 4]
^L
RFC 2481                       ECN to IP                    January 1999


   containing either a packet drop or an ECN indication.  However, we
   would like to point out some notable exceptions in the reaction of
   the source TCP, related to following the shorter-time-scale details
   of particular implementations of TCP.  For TCP's response to an ECN
   indication, we do not recommend such behavior as the slow-start of
   Tahoe TCP in response to a packet drop, or Reno TCP's wait of roughly
   half a round-trip time during Fast Recovery.

   One reason for requiring that the congestion-control response to the
   CE packet be essentially the same as the response to a dropped packet
   is to accommodate the incremental deployment of ECN in both end-
   systems and in routers.  Some routers may drop ECN-Capable packets
   (e.g., using the same RED policies for congestion detection) while
   other routers set the CE bit, for equivalent levels of congestion.
   Similarly, a router might drop a non-ECN-Capable packet but set the
   CE bit in an ECN-Capable packet, for equivalent levels of congestion.
   Different congestion control responses to a CE bit indication and to
   a packet drop could result in unfair treatment for different flows.

   An additional requirement is that the end-systems should react to
   congestion at most once per window of data (i.e., at most once per
   roundtrip time), to avoid reacting multiple times to multiple
   indications of congestion within a roundtrip time.

   For a router, the CE bit of an ECN-Capable packet should only be set
   if the router would otherwise have dropped the packet as an
   indication of congestion to the end nodes. When the router's buffer
   is not yet full and the router is prepared to drop a packet to inform
   end nodes of incipient congestion, the router should first check to
   see if the ECT bit is set in that packet's IP header.  If so, then
   instead of dropping the packet, the router MAY instead set the CE bit
   in the IP header.

   An environment where all end nodes were ECN-Capable could allow new
   criteria to be developed for setting the CE bit, and new congestion
   control mechanisms for end-node reaction to CE packets.  However,
   this is a research issue, and as such is not addressed in this
   document.

   When a CE packet is received by a router, the CE bit is left
   unchanged, and the packet transmitted as usual. When severe
   congestion has occurred and the router's queue is full, then the
   router has no choice but to drop some packet when a new packet
   arrives.  We anticipate that such packet losses will become
   relatively infrequent when a majority of end-systems become ECN-
   Capable and participate in TCP or other compatible congestion control
   mechanisms. In an adequately-provisioned network in such an ECN-
   Capable environment, packet losses should occur primarily during



Ramakrishnan & Floyd          Experimental                      [Page 5]
^L
RFC 2481                       ECN to IP                    January 1999


   transients or in the presence of non-cooperating sources.

   We expect that routers will set the CE bit in response to incipient
   congestion as indicated by the average queue size, using the RED
   algorithms suggested in [FJ93, RFC2309].  To the best of our
   knowledge, this is the only proposal currently under discussion in
   the IETF for routers to drop packets proactively, before the buffer
   overflows.  However, this document does not attempt to specify a
   particular mechanism for active queue management, leaving that
   endeavor, if needed, to other areas of the IETF.  While ECN is
   inextricably tied up with active queue management at the router, the
   reverse does not hold; active queue management mechanisms have been
   developed and deployed independently from ECN, using packet drops as
   indications of congestion in the absence of ECN in the IP
   architecture.

6. Support from the Transport Protocol

   ECN requires support from the transport protocol, in addition to the
   functionality given by the ECN field in the IP packet header. The
   transport protocol might require negotiation between the endpoints
   during setup to determine that all of the endpoints are ECN-capable,
   so that the sender can set the ECT bit in transmitted packets.
   Second, the transport protocol must be capable of reacting
   appropriately to the receipt of CE packets.  This reaction could be
   in the form of the data receiver informing the data sender of the
   received CE packet (e.g., TCP), of the data receiver unsubscribing to
   a layered multicast group (e.g., RLM [MJV96]), or of some other
   action that ultimately reduces the arrival rate of that flow to that
   receiver.

   This document only addresses the addition of ECN Capability to TCP,
   leaving issues of ECN and other transport protocols to further
   research.  For TCP, ECN requires three new mechanisms:  negotiation
   between the endpoints during setup to determine if they are both
   ECN-capable; an ECN-Echo flag in the TCP header so that the data
   receiver can inform the data sender when a CE packet has been
   received; and a Congestion Window Reduced (CWR) flag in the TCP
   header so that the data sender can inform the data receiver that the
   congestion window has been reduced. The support required from other
   transport protocols is likely to be different, particular for
   unreliable or reliable multicast transport protocols, and will have
   to be determined as other transport protocols are brought to the IETF
   for standardization.







Ramakrishnan & Floyd          Experimental                      [Page 6]
^L
RFC 2481                       ECN to IP                    January 1999


6.1. TCP

   The following sections describe in detail the proposed use of ECN in
   TCP.  This proposal is described in essentially the same form in
   [Floyd94]. We assume that the source TCP uses the standard congestion
   control algorithms of Slow-start, Fast Retransmit and Fast Recovery
   [RFC 2001].

   This proposal specifies two new flags in the Reserved field of the
   TCP header.  The TCP mechanism for negotiating ECN-Capability uses
   the ECN-Echo flag in the TCP header.  (This was called the ECN Notify
   flag in some earlier documents.)  Bit 9 in the Reserved field of the
   TCP header is designated as the ECN-Echo flag.  The location of the
   6-bit Reserved field in the TCP header is shown in Figure 3 of RFC
   793 [RFC793].

   To enable the TCP receiver to determine when to stop setting the
   ECN-Echo flag, we introduce a second new flag in the TCP header, the
   Congestion Window Reduced (CWR) flag.  The CWR flag is assigned to
   Bit 8 in the Reserved field of the TCP header.

   The use of these flags is described in the sections below.

6.1.1.  TCP Initialization

   In the TCP connection setup phase, the source and destination TCPs
   exchange information about their desire and/or capability to use ECN.
   Subsequent to the completion of this negotiation, the TCP sender sets
   the ECT bit in the IP header of data packets to indicate to the
   network that the transport is capable and willing to participate in
   ECN for this packet. This will indicate to the routers that they may
   mark this packet with the CE bit, if they would like to use that as a
   method of congestion notification. If the TCP connection does not
   wish to use ECN notification for a particular packet, the sending TCP
   sets the ECT bit equal to 0 (i.e., not set), and the TCP receiver
   ignores the CE bit in the received packet.

   When a node sends a TCP SYN packet, it may set the ECN-Echo and CWR
   flags in the TCP header.  For a SYN packet, the setting of both the
   ECN-Echo and CWR flags are defined as an indication that the sending
   TCP is ECN-Capable, rather than as an indication of congestion or of
   response to congestion. More precisely, a SYN packet with both the
   ECN-Echo and CWR flags set indicates that the TCP implementation
   transmitting the SYN packet will participate in ECN as both a sender
   and receiver.  As a receiver, it will respond to incoming data
   packets that have the CE bit set in the IP header by setting the
   ECN-Echo flag in outgoing TCP Acknowledgement (ACK) packets.  As a
   sender, it will respond to incoming packets that have the ECN-Echo



Ramakrishnan & Floyd          Experimental                      [Page 7]
^L
RFC 2481                       ECN to IP                    January 1999


   flag set by reducing the congestion window when appropriate.

   When a node sends a SYN-ACK packet, it may set the ECN-Echo flag, but
   it does not set the CWR flag.  For a SYN-ACK packet, the pattern of
   the ECN-Echo flag set and the CWR flag not set in the TCP header is
   defined as an indication that the TCP transmitting the SYN-ACK packet
   is ECN-Capable.

   There is the question of why we chose to have the TCP sending the SYN
   set two ECN-related flags in the Reserved field of the TCP header for
   the SYN packet, while the responding TCP sending the SYN-ACK sets
   only one ECN-related flag in the SYN-ACK packet.  This asymmetry is
   necessary for the robust negotiation of ECN-capability with deployed
   TCP implementations.  There exists at least one TCP implementation in
   which TCP receivers set the Reserved field of the TCP header in ACK
   packets (and hence the SYN-ACK) simply to reflect the Reserved field
   of the TCP header in the received data packet.  Because the TCP SYN
   packet sets the ECN-Echo and CWR flags to indicate ECN-capability,
   while the SYN-ACK packet sets only the ECN-Echo flag, the sending TCP
   correctly interprets a receiver's reflection of its own flags in the
   Reserved field as an indication that the receiver is not ECN-capable.

6.1.2.  The TCP Sender

   For a TCP connection using ECN, data packets are transmitted with the
   ECT bit set in the IP header (set to a "1").  If the sender receives
   an ECN-Echo ACK packet (that is, an ACK packet with the ECN-Echo flag
   set in the TCP header), then the sender knows that congestion was
   encountered in the network on the path from the sender to the
   receiver.  The indication of congestion should be treated just as a
   congestion loss in non-ECN-Capable TCP. That is, the TCP source
   halves the congestion window "cwnd" and reduces the slow start
   threshold "ssthresh".  The sending TCP does NOT increase the
   congestion window in response to the receipt of an ECN-Echo ACK
   packet.

   A critical condition is that TCP does not react to congestion
   indications more than once every window of data (or more loosely,
   more than once every round-trip time). That is, the TCP sender's
   congestion window should be reduced only once in response to a series
   of dropped and/or CE packets from a single window of data, In
   addition, the TCP source should not decrease the slow-start
   threshold, ssthresh, if it has been decreased within the last round
   trip time.  However, if any retransmitted packets are dropped or have
   the CE bit set, then this is interpreted by the source TCP as a new
   instance of congestion.





Ramakrishnan & Floyd          Experimental                      [Page 8]
^L
RFC 2481                       ECN to IP                    January 1999


   After the source TCP reduces its congestion window in response to a
   CE packet, incoming acknowledgements that continue to arrive can
   "clock out" outgoing packets as allowed by the reduced congestion
   window.  If the congestion window consists of only one MSS (maximum
   segment size), and the sending TCP receives an ECN-Echo ACK packet,
   then the sending TCP should in principle still reduce its congestion
   window in half. However, the value of the congestion window is
   bounded below by a value of one MSS.  If the sending TCP were to
   continue to send, using a congestion window of 1 MSS, this results in
   the transmission of one packet per round-trip time.  We believe it is
   desirable to still reduce the sending rate of the TCP sender even
   further, on receipt of an ECN-Echo packet when the congestion window
   is one.  We use the retransmit timer as a means to reduce the rate
   further in this circumstance.  Therefore, the sending TCP should also
   reset the retransmit timer on receiving the ECN-Echo packet when the
   congestion window is one.  The sending TCP will then be able to send
   a new packet when the retransmit timer expires.

   [Floyd94] discusses TCP's response to ECN in more detail.  [Floyd98]
   discusses the validation test in the ns simulator, which illustrates
   a wide range of ECN scenarios. These scenarios include the following:
   an ECN followed by another ECN, a Fast Retransmit, or a Retransmit
   Timeout; a Retransmit Timeout or a Fast Retransmit followed by an
   ECN, and a congestion window of one packet followed by an ECN.

   TCP follows existing algorithms for sending data packets in response
   to incoming ACKs, multiple duplicate acknowledgements, or retransmit
   timeouts [RFC2001].

6.1.3.  The TCP Receiver

   When TCP receives a CE data packet at the destination end-system, the
   TCP data receiver sets the ECN-Echo flag in the TCP header of the
   subsequent ACK packet.  If there is any ACK withholding implemented,
   as in current "delayed-ACK" TCP implementations where the TCP
   receiver can send an ACK for two arriving data packets, then the
   ECN-Echo flag in the ACK packet will be set to the OR of the CE bits
   of all of the data packets being acknowledged.  That is, if any of
   the received data packets are CE packets, then the returning ACK has
   the ECN-Echo flag set.

   To provide robustness against the possibility of a dropped ACK packet
   carrying an ECN-Echo flag, the TCP receiver must set the ECN-Echo
   flag in a series of ACK packets. The TCP receiver uses the CWR flag
   to determine when to stop setting the ECN-Echo flag.






Ramakrishnan & Floyd          Experimental                      [Page 9]
^L
RFC 2481                       ECN to IP                    January 1999


   When an ECN-Capable TCP reduces its congestion window for any reason
   (because of a retransmit timeout, a Fast Retransmit, or in response
   to an ECN Notification), the TCP sets the CWR flag in the TCP header
   of the first data packet sent after the window reduction.  If that
   data packet is dropped in the network, then the sending TCP will have
   to reduce the congestion window again and retransmit the dropped
   packet.  Thus, the Congestion Window Reduced message is reliably
   delivered to the data receiver.

   After a TCP receiver sends an ACK packet with the ECN-Echo bit set,
   that TCP receiver continues to set the ECN-Echo flag in ACK packets
   until it receives a CWR packet (a packet with the CWR flag set).
   After the receipt of the CWR packet, acknowledgements for subsequent
   non-CE data packets do not have the ECN-Echo flag set. If another CE
   packet is received by the data receiver, the receiver would once
   again send ACK packets with the ECN-Echo flag set.  While the receipt
   of a CWR packet does not guarantee that the data sender received the
   ECN-Echo message, this does indicate that the data sender reduced its
   congestion window at some point *after* it sent the data packet for
   which the CE bit was set.

   We have already specified that a TCP sender reduces its congestion
   window at most once per window of data.  This mechanism requires some
   care to make sure that the sender reduces its congestion window at
   most once per ECN indication, and that multiple ECN messages over
   several successive windows of data are properly reported to the ECN
   sender.  This is discussed further in [Floyd98].

6.1.4. Congestion on the ACK-path

   For the current generation of TCP congestion control algorithms, pure
   acknowledgement packets (e.g., packets that do not contain any
   accompanying data) should be sent with the ECT bit off. Current TCP
   receivers have no mechanisms for reducing traffic on the ACK-path in
   response to congestion notification.  Mechanisms for responding to
   congestion on the ACK-path are areas for current and future research.
   (One simple possibility would be for the sender to reduce its
   congestion window when it receives a pure ACK packet with the CE bit
   set). For current TCP implementations, a single dropped ACK generally
   has only a very small effect on the TCP's sending rate.

7. Summary of changes required in IP and TCP

   Two bits need to be specified in the IP header, the ECN-Capable
   Transport (ECT) bit and the Congestion Experienced (CE) bit.  The ECT
   bit set to "0" indicates that the transport protocol will ignore the





Ramakrishnan & Floyd          Experimental                     [Page 10]
^L
RFC 2481                       ECN to IP                    January 1999


   CE bit.  This is the default value for the ECT bit.  The ECT bit set
   to "1" indicates that the transport protocol is willing and able to
   participate in ECN.

   The default value for the CE bit is "0".  The router sets the CE bit
   to "1" to indicate congestion to the end nodes.  The CE bit in a
   packet header should never be reset by a router from "1" to "0".

   TCP requires three changes, a negotiation phase during setup to
   determine if both end nodes are ECN-capable, and two new flags in the
   TCP header, from the "reserved" flags in the TCP flags field.  The
   ECN-Echo flag is used by the data receiver to inform the data sender
   of a received CE packet.  The Congestion Window Reduced flag is used
   by the data sender to inform the data receiver that the congestion
   window has been reduced.

8. Non-relationship to ATM's EFCI indicator or Frame Relay's FECN

   Since the ATM and Frame Relay mechanisms for congestion indication
   have typically been defined without any notion of average queue size
   as the basis for determining that an intermediate node is congested,
   we believe that they provide a very noisy signal. The TCP-sender
   reaction specified in this draft for ECN is NOT the appropriate
   reaction for such a noisy signal of congestion notification. It is
   our expectation that ATM's EFCI and Frame Relay's FECN mechanisms
   would be phased out over time within the ATM network.  However, if
   the routers that interface to the ATM network have a way of
   maintaining the average queue at the interface, and use it to come to
   a reliable determination that the ATM subnet is congested, they may
   use the ECN notification that is defined here.

   We emphasize that a *single* packet with the CE bit set in an IP
   packet causes the transport layer to respond, in terms of congestion
   control, as it would to a packet drop.  As such, the CE bit is not a
   good match to a transient signal such as one based on the
   instantaneous queue size.  However, experiments in techniques at
   layer 2 (e.g., in ATM switches or Frame Relay switches) should be
   encouraged.  For example, using a scheme such as RED (where packet
   marking is based on the average queue length exceeding a threshold),
   layer 2 devices could provide a reasonably reliable indication of
   congestion.  When all the layer 2 devices in a path set that layer's
   own Congestion Experienced bit (e.g., the EFCI bit for ATM, the FECN
   bit in Frame Relay) in this reliable manner, then the interface
   router to the layer 2 network could copy the state of that layer 2
   Congestion Experienced bit into the CE bit in the IP header.  We
   recognize that this is not the current practice, nor is it in current
   standards. However, encouraging experimentation in this manner may




Ramakrishnan & Floyd          Experimental                     [Page 11]
^L
RFC 2481                       ECN to IP                    January 1999


   provide the information needed to enable evolution of existing layer
   2 mechanisms to provide a more reliable means of congestion
   indication, when they use a single bit for indicating congestion.

9. Non-compliance by the End Nodes

   This section discusses concerns about the vulnerability of ECN to
   non-compliant end-nodes (i.e., end nodes that set the ECT bit in
   transmitted packets but do not respond to received CE packets).  We
   argue that the addition of ECN to the IP architecture would not
   significantly increase the current vulnerability of the architecture
   to unresponsive flows.

   Even for non-ECN environments, there are serious concerns about the
   damage that can be done by non-compliant or unresponsive flows (that
   is, flows that do not respond to congestion control indications by
   reducing their arrival rate at the congested link).  For example, an
   end-node could "turn off congestion control" by not reducing its
   congestion window in response to packet drops. This is a concern for
   the current Internet.  It has been argued that routers will have to
   deploy mechanisms to detect and differentially treat packets from
   non-compliant flows.  It has also been argued that techniques such as
   end-to-end per-flow scheduling and isolation of one flow from
   another, differentiated services, or end-to-end reservations could
   remove some of the more damaging effects of unresponsive flows.

   It has been argued that dropping packets in itself may be an adequate
   deterrent for non-compliance, and that the use of ECN removes this
   deterrent.  We would argue in response that (1) ECN-capable routers
   preserve packet-dropping behavior in times of high congestion; and
   (2) even in times of high congestion, dropping packets in itself is
   not an adequate deterrent for non-compliance.

   First, ECN-Capable routers will only mark packets (as opposed to
   dropping them) when the packet marking rate is reasonably low. During
   periods where the average queue size exceeds an upper threshold, and
   therefore the potential packet marking rate would be high, our
   recommendation is that routers drop packets rather then set the CE
   bit in packet headers.

   During the periods of low or moderate packet marking rates when ECN
   would be deployed, there would be little deterrent effect on
   unresponsive flows of dropping rather than marking those packets. For
   example, delay-insensitive flows using reliable delivery might have
   an incentive to increase rather than to decrease their sending rate
   in the presence of dropped packets.  Similarly, delay-sensitive flows
   using unreliable delivery might increase their use of FEC in response
   to an increased packet drop rate, increasing rather than decreasing



Ramakrishnan & Floyd          Experimental                     [Page 12]
^L
RFC 2481                       ECN to IP                    January 1999


   their sending rate.  For the same reasons, we do not believe that
   packet dropping itself is an effective deterrent for non-compliance
   even in an environment of high packet drop rates.

   Several methods have been proposed to identify and restrict non-
   compliant or unresponsive flows. The addition of ECN to the network
   environment would not in any way increase the difficulty of designing
   and deploying such mechanisms. If anything, the addition of ECN to
   the architecture would make the job of identifying unresponsive flows
   slightly easier.  For example, in an ECN-Capable environment routers
   are not limited to information about packets that are dropped or have
   the CE bit set at that router itself; in such an environment routers
   could also take note of arriving CE packets that indicate congestion
   encountered by that packet earlier in the path.

10. Non-compliance in the Network

   The breakdown of effective congestion control could be caused not
   only by a non-compliant end-node, but also by the loss of the
   congestion indication in the network itself.  This could happen
   through a rogue or broken router that set the ECT bit in a packet
   from a non-ECN-capable transport, or "erased" the CE bit in arriving
   packets.  As one example, a rogue or broken router that "erased" the
   CE bit in arriving CE packets would prevent that indication of
   congestion from reaching downstream receivers.  This could result in
   the failure of congestion control for that flow and a resulting
   increase in congestion in the network, ultimately resulting in
   subsequent packets dropped for this flow as the average queue size
   increased at the congested gateway.

   The actions of a rogue or broken router could also result in an
   unnecessary indication of congestion to the end-nodes.  These actions
   can include a router dropping a packet or setting the CE bit in the
   absence of congestion. From a congestion control point of view,
   setting the CE bit in the absence of congestion by a non-compliant
   router would be no different than a router dropping a packet
   unecessarily. By "erasing" the ECT bit of a packet that is later
   dropped in the network, a router's actions could result in an
   unnecessary packet drop for that packet later in the network.

   Concerns regarding the loss of congestion indications from
   encapsulated, dropped, or corrupted packets are discussed below.









Ramakrishnan & Floyd          Experimental                     [Page 13]
^L
RFC 2481                       ECN to IP                    January 1999


10.1. Encapsulated packets

   Some care is required to handle the CE and ECT bits appropriately
   when packets are encapsulated and de-encapsulated for tunnels.

   When a packet is encapsulated, the following rules apply regarding
   the ECT bit.  First, if the ECT bit in the encapsulated ('inside')
   header is a 0, then the ECT bit in the encapsulating ('outside')
   header MUST be a 0.  If the ECT bit in the inside header is a 1, then
   the ECT bit in the outside header SHOULD be a 1.

   When a packet is de-encapsulated, the following rules apply regarding
   the CE bit.  If the ECT bit is a 1 in both the inside and the outside
   header, then the CE bit in the outside header MUST be ORed with the
   CE bit in the inside header.  (That is, in this case a CE bit of 1 in
   the outside header must be copied to the inside header.)  If the ECT
   bit in either header is a 0, then the CE bit in the outside header is
   ignored.  This requirement for the treatment of de-encapsulated
   packets does not currently apply to IPsec tunnels.

   A specific example of the use of ECN with encapsulation occurs when a
   flow wishes to use ECN-capability to avoid the danger of an
   unnecessary packet drop for the encapsulated packet as a result of
   congestion at an intermediate node in the tunnel.  This functionality
   can be supported by copying the ECN field in the inner IP header to
   the outer IP header upon encapsulation, and using the ECN field in
   the outer IP header to set the ECN field in the inner IP header upon
   decapsulation.  This effectively allows routers along the tunnel to
   cause the CE bit to be set in the ECN field of the unencapsulated IP
   header of an ECN-capable packet when such routers experience
   congestion.

10.2.  IPsec Tunnel Considerations

   The IPsec protocol, as defined in [ESP, AH], does not include the IP
   header's ECN field in any of its cryptographic calculations (in the
   case of tunnel mode, the outer IP header's ECN field is not
   included).  Hence modification of the ECN field by a network node has
   no effect on IPsec's end-to-end security, because it cannot cause any
   IPsec integrity check to fail.  As a consequence, IPsec does not
   provide any defense against an adversary's modification of the ECN
   field (i.e., a man-in-the-middle attack), as the adversary's
   modification will also have no effect on IPsec's end-to-end security.
   In some environments, the ability to modify the ECN field without
   affecting IPsec integrity checks may constitute a covert channel; if
   it is necessary to eliminate such a channel or reduce its bandwidth,
   then the outer IP header's ECN field can be zeroed at the tunnel
   ingress and egress nodes.



Ramakrishnan & Floyd          Experimental                     [Page 14]
^L
RFC 2481                       ECN to IP                    January 1999


   The IPsec protocol currently requires that the inner header's ECN
   field not be changed by IPsec decapsulation processing at a tunnel
   egress node.  This ensures that an adversary's modifications to the
   ECN field cannot be used to launch theft- or denial-of-service
   attacks across an IPsec tunnel endpoint, as any such modifications
   will be discarded at the tunnel endpoint.  This document makes no
   change to that IPsec requirement. As a consequence of the current
   specification of the IPsec protocol, we suggest that experiments with
   ECN not be carried out for flows that will undergo IPsec tunneling at
   the present time.

   If the IPsec specifications are modified in the future to permit a
   tunnel egress node to modify the ECN field in an inner IP header
   based on the ECN field value in the outer header (e.g., copying part
   or all of the outer ECN field to the inner ECN field), or to permit
   the ECN field of the outer IP header to be zeroed during
   encapsulation, then experiments with ECN may be used in combination
   with IPsec tunneling.

   This discussion of ECN and IPsec tunnel considerations draws heavily
   on related discussions and documents from the Differentiated Services
   Working Group.

10.3.  Dropped or Corrupted Packets

   An additional issue concerns a packet that has the CE bit set at one
   router and is dropped by a subsequent router.  For the proposed use
   for ECN in this paper (that is, for a transport protocol such as TCP
   for which a dropped data packet is an indication of congestion), end
   nodes detect dropped data packets, and the congestion response of the
   end nodes to a dropped data packet is at least as strong as the
   congestion response to a received CE packet.

   However, transport protocols such as TCP do not necessarily detect
   all packet drops, such as the drop of a "pure" ACK packet; for
   example, TCP does not reduce the arrival rate of subsequent ACK
   packets in response to an earlier dropped ACK packet.  Any proposal
   for extending ECN-Capability to such packets would have to address
   concerns raised by CE packets that were later dropped in the network.

   Similarly, if a CE packet is dropped later in the network due to
   corruption (bit errors), the end nodes should still invoke congestion
   control, just as TCP would today in response to a dropped data
   packet. This issue of corrupted CE packets would have to be
   considered in any proposal for the network to distinguish between
   packets dropped due to corruption, and packets dropped due to
   congestion or buffer overflow.




Ramakrishnan & Floyd          Experimental                     [Page 15]
^L
RFC 2481                       ECN to IP                    January 1999


11. A summary of related work.

   [Floyd94] considers the advantages and drawbacks of adding ECN to the
   TCP/IP architecture.  As shown in the simulation-based comparisons,
   one advantage of ECN is to avoid unnecessary packet drops for short
   or delay-sensitive TCP connections.  A second advantage of ECN is in
   avoiding some unnecessary retransmit timeouts in TCP.  This paper
   discusses in detail the integration of ECN into TCP's congestion
   control mechanisms.  The possible disadvantages of ECN discussed in
   the paper are that a non-compliant TCP connection could falsely
   advertise itself as ECN-capable, and that a TCP ACK packet carrying
   an ECN-Echo message could itself be dropped in the network.  The
   first of these two issues is discussed in Section 8 of this document,
   and the second is addressed by the proposal in Section 5.1.3 for a
   CWR flag in the TCP header.

   [CKLTZ97] reports on an experimental implementation of ECN in IPv6.
   The experiments include an implementation of ECN in an existing
   implementation of RED for FreeBSD.  A number of experiments were run
   to demonstrate the control of the average queue size in the router,
   the performance of ECN for a single TCP connection as a congested
   router, and fairness with multiple competing TCP connections.  One
   conclusion of the experiments is that dropping packets from a bulk-
   data transfer can degrade performance much more severely than marking
   packets.

   Because the experimental implementation in [CKLTZ97] predates some of
   the developments in this document, the implementation does not
   conform to this document in all respects.  For example, in the
   experimental implementation the CWR flag is not used, but instead the
   TCP receiver sends the ECN-Echo bit on a single ACK packet.

   [K98] and [CKLTZ98] build on [CKLTZ97] to further analyze the
   benefits of ECN for TCP. The conclusions are that ECN TCP gets
   moderately better throughput than non-ECN TCP; that ECN TCP flows are
   fair towards non-ECN TCP flows; and that ECN TCP is robust with two-
   way traffic, congestion in both directions, and with multiple
   congested gateways.  Experiments with many short web transfers show
   that, while most of the short connections have similar transfer times
   with or without ECN, a small percentage of the short connections have
   very long transfer times for the non-ECN experiments as compared to
   the ECN experiments.  This increased transfer time is particularly
   dramatic for those short connections that have their first packet
   dropped in the non-ECN experiments, and that therefore have to wait
   six seconds for the retransmit timer to expire.

   The ECN Web Page [ECN] has pointers to other implementations of ECN
   in progress.



Ramakrishnan & Floyd          Experimental                     [Page 16]
^L
RFC 2481                       ECN to IP                    January 1999


12. Conclusions

   Given the current effort to implement RED, we believe this is the
   right time for router vendors to examine how to implement congestion
   avoidance mechanisms that do not depend on packet drops alone.  With
   the increased deployment of applications and transports sensitive to
   the delay and loss of a single packet (e.g., realtime traffic, short
   web transfers), depending on packet loss as a normal congestion
   notification mechanism appears to be insufficient (or at the very
   least, non-optimal).

13. Acknowledgements

   Many people have made contributions to this RFC.  In particular, we
   would like to thank Kenjiro Cho for the proposal for the TCP
   mechanism for negotiating ECN-Capability, Kevin Fall for the proposal
   of the CWR bit, Steve Blake for material on IPv4 Header Checksum
   Recalculation, Jamal Hadi Salim for discussions of ECN issues, and
   Steve Bellovin, Jim Bound, Brian Carpenter, Paul Ferguson, Stephen
   Kent, Greg Minshall, and Vern Paxson for discussions of security
   issues.  We also thank the Internet End-to-End Research Group for
   ongoing discussions of these issues.


14. References

   [AH]         Kent, S. and R. Atkinson, "IP Authentication Header",
                RFC 2402, November 1998.

   [B97]        Bradner, S., "Key words for use in RFCs to Indicate
                Requirement Levels", BCP 14, RFC 2119, March 1997.

   [CKLT98]     Chen, C., Krishnan, H., Leung, S., Tang, N., and Zhang,
                L., "Implementing ECN for TCP/IPv6", presentation to the
                ECN BOF at the L.A. IETF, March 1998, URL
                "http://www.cs.ucla.edu/~hari/ecn-ietf.ps".

   [DIFFSERV]   Nichols, K., Blake, S., Baker, F. and D.  Black,
                "Definition of the Differentiated Services Field (DS
                Field) in the IPv4 and IPv6 Headers", RFC 2474, December
                1998.

   [ECN]        "The ECN Web Page", URL "http://www-
                nrg.ee.lbl.gov/floyd/ecn.html".

   [ESP]        Kent, S. and R. Atkinson, "IP Encapsulating Security
                Payload", RFC 2406, November 1998.




Ramakrishnan & Floyd          Experimental                     [Page 17]
^L
RFC 2481                       ECN to IP                    January 1999


   [FJ93]       Floyd, S., and Jacobson, V., "Random Early Detection
                gateways for Congestion Avoidance", IEEE/ACM
                Transactions on Networking, V.1 N.4, August 1993, p.
                397-413.  URL "ftp://ftp.ee.lbl.gov/papers/early.pdf".

   [Floyd94]    Floyd, S., "TCP and Explicit Congestion Notification",
                ACM Computer Communication Review, V. 24 N. 5, October
                1994, p. 10-23.  URL
                "ftp://ftp.ee.lbl.gov/papers/tcp_ecn.4.ps.Z".

   [Floyd97]    Floyd, S., and Fall, K., "Router Mechanisms to Support
                End-to-End Congestion Control", Technical report,
                February 1997.  URL "http://www-
                nrg.ee.lbl.gov/floyd/end2end-paper.html".

   [Floyd98]    Floyd, S., "The ECN Validation Test in the NS
                Simulator", URL "http://www-mash.cs.berkeley.edu/ns/",
                test tcl/test/test-all-ecn.

   [K98]        Krishnan, H., "Analyzing Explicit Congestion
                Notification (ECN) benefits for TCP", Master's thesis,
                UCLA, 1998, URL
                "http://www.cs.ucla.edu/~hari/software/ecn/
                ecn_report.ps.gz".

   [FRED]       Lin, D., and Morris, R., "Dynamics of Random Early
                Detection", SIGCOMM '97, September 1997.  URL
                "http://www.inria.fr/rodeo/sigcomm97/program.html#ab078".

   [Jacobson88] V. Jacobson, "Congestion Avoidance and Control", Proc.
                ACM SIGCOMM '88, pp. 314-329.  URL
                "ftp://ftp.ee.lbl.gov/papers/congavoid.ps.Z".

   [Jacobson90] V. Jacobson, "Modified TCP Congestion Avoidance
                Algorithm", Message to end2end-interest mailing list,
                April 1990.  URL
                "ftp://ftp.ee.lbl.gov/email/vanj.90apr30.txt".

   [MJV96]      S. McCanne, V. Jacobson, and M. Vetterli, "Receiver-
                driven Layered Multicast", SIGCOMM '96, August 1996, pp.
                117-130.

   [RFC791]     Postel, J., "Internet Protocol", STD 5, RFC 791,
                September 1981.

   [RFC793]     Postel, J., "Transmission Control Protocol", STD 7, RFC
                793, September 1981.




Ramakrishnan & Floyd          Experimental                     [Page 18]
^L
RFC 2481                       ECN to IP                    January 1999


   [RFC1141]    Mallory, T. and A. Kullberg, "Incremental Updating of
                the Internet Checksum", RFC 1141, January 1990.

   [RFC1349]    Almquist, P., "Type of Service in the Internet Protocol
                Suite", RFC 1349, July 1992.

   [RFC1455]    Eastlake, D., "Physical Link Security Type of Service",
                RFC 1455, May 1993.

   [RFC2001]    Stevens, W., "TCP Slow Start, Congestion Avoidance, Fast
                Retransmit, and Fast Recovery Algorithms", RFC 2001,
                January 1997.

   [RFC2309]    Braden, B., Clark, D., Crowcroft, J., Davie, B.,
                Deering, S., Estrin, D., Floyd, S., Jacobson, V.,
                Minshall, G., Partridge, C., Peterson, L., Ramakrishnan,
                K., Shenker, S., Wroclawski, J. and L. Zhang,
                "Recommendations on Queue Management and Congestion
                Avoidance in the Internet", RFC 2309, April 1998.

   [RJ90]       K. K. Ramakrishnan and Raj Jain, "A Binary Feedback
                Scheme for Congestion Avoidance in Computer Networks",
                ACM Transactions on Computer Systems, Vol.8, No.2, pp.
                158-181, May 1990.

15. Security Considerations

   Security considerations have been discussed in Section 9.

16. IPv4 Header Checksum Recalculation

   IPv4 header checksum recalculation is an issue with some high-end
   router architectures using an output-buffered switch, since most if
   not all of the header manipulation is performed on the input side of
   the switch, while the ECN decision would need to be made local to the
   output buffer. This is not an issue for IPv6, since there is no IPv6
   header checksum. The IPv4 TOS octet is the last byte of a 16-bit
   half-word.

   RFC 1141 [RFC1141] discusses the incremental updating of the IPv4
   checksum after the TTL field is decremented.  The incremental
   updating of the IPv4 checksum after the CE bit was set would work as
   follows: Let HC be the original header checksum, and let HC' be the
   new header checksum after the CE bit has been set.  Then for header
   checksums calculated with one's complement subtraction, HC' would be
   recalculated as follows:





Ramakrishnan & Floyd          Experimental                     [Page 19]
^L
RFC 2481                       ECN to IP                    January 1999


      HC' = { HC - 1     HC > 1
            { 0x0000     HC = 1

   For header checksums calculated on two's complement machines, HC'
   would be recalculated as follows after the CE bit was set:

       HC' = { HC - 1     HC > 0
             { 0xFFFE     HC = 0

17. The motivation for the ECT bit.

   The need for the ECT bit is motivated by the fact that ECN will be
   deployed incrementally in an Internet where some transport protocols
   and routers understand ECN and some do not. With the ECT bit, the
   router can drop packets from flows that are not ECN-capable, but can
   *instead* set the CE bit in flows that *are* ECN-capable. Because the
   ECT bit allows an end node to have the CE bit set in a packet
   *instead* of having the packet dropped, an end node might have some
   incentive to deploy ECN.

   If there was no ECT indication, then the router would have to set the
   CE bit for packets from both ECN-capable and non-ECN-capable flows.
   In this case, there would be no incentive for end-nodes to deploy
   ECN, and no viable path of incremental deployment from a non-ECN
   world to an ECN-capable world.  Consider the first stages of such an
   incremental deployment, where a subset of the flows are ECN-capable.
   At the onset of congestion, when the packet dropping/marking rate
   would be low, routers would only set CE bits, rather than dropping
   packets.  However, only those flows that are ECN-capable would
   understand and respond to CE packets. The result is that the ECN-
   capable flows would back off, and the non-ECN-capable flows would be
   unaware of the ECN signals and would continue to open their
   congestion windows.

   In this case, there are two possible outcomes: (1) the ECN-capable
   flows back off, the non-ECN-capable flows get all of the bandwidth,
   and congestion remains mild, or (2) the ECN-capable flows back off,
   the non-ECN-capable flows don't, and congestion increases until the
   router transitions from setting the CE bit to dropping packets.
   While this second outcome evens out the fairness, the ECN-capable
   flows would still receive little benefit from being ECN-capable,
   because the increased congestion would drive the router to packet-
   dropping behavior.

   A flow that advertised itself as ECN-Capable but does not respond to
   CE bits is functionally equivalent to a flow that turns off
   congestion control, as discussed in Sections 8 and 9.




Ramakrishnan & Floyd          Experimental                     [Page 20]
^L
RFC 2481                       ECN to IP                    January 1999


   Thus, in a world when a subset of the flows are ECN-capable, but
   where ECN-capable flows have no mechanism for indicating that fact to
   the routers, there would be less effective and less fair congestion
   control in the Internet, resulting in a strong incentive for end
   nodes not to deploy ECN.

18. Why use two bits in the IP header?

   Given the need for an ECT indication in the IP header, there still
   remains the question of whether the ECT (ECN-Capable Transport) and
   CE (Congestion Experienced) indications should be overloaded on a
   single bit.  This overloaded-one-bit alternative, explored in
   [Floyd94], would involve a single bit with two values.  One value,
   "ECT and not CE", would represent an ECN-Capable Transport, and the
   other value, "CE or not ECT", would represent either Congestion
   Experienced or a non-ECN-Capable transport.

   One difference between the one-bit and two-bit implementations
   concerns packets that traverse multiple congested routers.  Consider
   a CE packet that arrives at a second congested router, and is
   selected by the active queue management at that router for either
   marking or dropping.  In the one-bit implementation, the second
   congested router has no choice but to drop the CE packet, because it
   cannot distinguish between a CE packet and a non-ECT packet.  In the
   two-bit implementation, the second congested router has the choice of
   either dropping the CE packet, or of leaving it alone with the CE bit
   set.

   Another difference between the one-bit and two-bit implementations
   comes from the fact that with the one-bit implementation, receivers
   in a single flow cannot distinguish between CE and non-ECT packets.
   Thus, in the one-bit implementation an ECN-capable data sender would
   have to unambiguously indicate to the receiver or receivers whether
   each packet had been sent as ECN-Capable or as non-ECN-Capable.  One
   possibility would be for the sender to indicate in the transport
   header whether the packet was sent as ECN-Capable.  A second
   possibility that would involve a functional limitation for the one-
   bit implementation would be for the sender to unambiguously indicate
   that it was going to send *all* of its packets as ECN-Capable or as
   non-ECN-Capable.  For a multicast transport protocol, this
   unambiguous indication would have to be apparent to receivers joining
   an on-going multicast session.

   Another advantage of the two-bit approach is that it is somewhat more
   robust.  The most critical issue, discussed in Section 8, is that the
   default indication should be that of a non-ECN-Capable transport.  In
   a two-bit implementation, this requirement for the default value
   simply means that the ECT bit should be `OFF' by default.  In the



Ramakrishnan & Floyd          Experimental                     [Page 21]
^L
RFC 2481                       ECN to IP                    January 1999


   one-bit implementation, this means that the single overloaded bit
   should by default be in the "CE or not ECT" position.  This is less
   clear and straightforward, and possibly more open to incorrect
   implementations either in the end nodes or in the routers.

   In summary, while the one-bit implementation could be a possible
   implementation, it has the following significant limitations relative
   to the two-bit implementation.  First, the one-bit implementation has
   more limited functionality for the treatment of CE packets at a
   second congested router.  Second, the one-bit implementation requires
   either that extra information be carried in the transport header of
   packets from ECN-Capable flows (to convey the functionality of the
   second bit elsewhere, namely in the transport header), or that
   senders in ECN-Capable flows accept the limitation that receivers
   must be able to determine a priori which packets are ECN-Capable and
   which are not ECN-Capable. Third, the one-bit implementation is
   possibly more open to errors from faulty implementations that choose
   the wrong default value for the ECN bit.  We believe that the use of
   the extra bit in the IP header for the ECT-bit is extremely valuable
   to overcome these limitations.

19.  Historical definitions for the IPv4 TOS octet

   RFC 791 [RFC791] defined the ToS (Type of Service) octet in the IP
   header.  In RFC 791, bits 6 and 7 of the ToS octet are listed as
   "Reserved for Future Use", and are shown set to zero.  The first two
   fields of the ToS octet were defined as the Precedence and Type of
   Service (TOS) fields.

            0     1     2     3     4     5     6     7
         +-----+-----+-----+-----+-----+-----+-----+-----+
         |   PRECEDENCE    |       TOS       |  0  |  0  |    RFC 791
         +-----+-----+-----+-----+-----+-----+-----+-----+

   RFC 1122 included bits 6 and 7 in the TOS field, though it did not
   discuss any specific use for those two bits:

            0     1     2     3     4     5     6     7
         +-----+-----+-----+-----+-----+-----+-----+-----+
         |   PRECEDENCE    |       TOS                   |    RFC 1122
         +-----+-----+-----+-----+-----+-----+-----+-----+

   The IPv4 TOS octet was redefined in RFC 1349 [RFC1349] as follows:

            0     1     2     3     4     5     6     7
         +-----+-----+-----+-----+-----+-----+-----+-----+
         |   PRECEDENCE    |       TOS             | MBZ |    RFC 1349
         +-----+-----+-----+-----+-----+-----+-----+-----+



Ramakrishnan & Floyd          Experimental                     [Page 22]
^L
RFC 2481                       ECN to IP                    January 1999


   Bit 6 in the TOS field was defined in RFC 1349 for "Minimize Monetary
   Cost".  In addition to the Precedence and Type of Service (TOS)
   fields, the last field, MBZ (for "must be zero") was defined as
   currently unused.  RFC 1349 stated that "The originator of a datagram
   sets [the MBZ] field to zero (unless participating in an Internet
   protocol experiment which makes use of that bit)."

   RFC 1455 [RFC 1455] defined an experimental standard that used all
   four bits in the TOS field to request a guaranteed level of link
   security.

   RFC 1349 is obsoleted by "Definition of the Differentiated Services
   Field (DS Field) in the IPv4 and IPv6 Headers" [DIFFSERV], in which
   bits 6 and 7 of the DS field are listed as Currently Unused (CU).
   The first six bits of the DS field are defined as the Differentiated
   Services CodePoint (DSCP):

            0     1     2     3     4     5     6     7
         +-----+-----+-----+-----+-----+-----+-----+-----+
         |               DSCP                |    CU     |
         +-----+-----+-----+-----+-----+-----+-----+-----+

   Because of this unstable history, the definition of the ECN field in
   this document cannot be guaranteed to be backwards compatible with
   all past uses of these two bits.  The damage that could be done by a
   non-ECN-capable router would be to "erase" the CE bit for an ECN-
   capable packet that arrived at the router with the CE bit set, or set
   the CE bit even in the absence of congestion.  This has been
   discussed in Section 10 on "Non-compliance in the Network".

   The damage that could be done in an ECN-capable environment by a
   non-ECN-capable end-node transmitting packets with the ECT bit set
   has been discussed in Section 9 on "Non-compliance by the End Nodes".


















Ramakrishnan & Floyd          Experimental                     [Page 23]
^L
RFC 2481                       ECN to IP                    January 1999


AUTHORS' ADDRESSES

   K. K. Ramakrishnan
   AT&T Labs. Research

   Phone: +1 (973) 360-8766
   EMail: kkrama@research.att.com
   URL: http://www.research.att.com/info/kkrama


   Sally Floyd
   Lawrence Berkeley National Laboratory

   Phone: +1 (510) 486-7518
   EMail: floyd@ee.lbl.gov
   URL: http://www-nrg.ee.lbl.gov/floyd/



































Ramakrishnan & Floyd          Experimental                     [Page 24]
^L
RFC 2481                       ECN to IP                    January 1999


Full Copyright Statement

   Copyright (C) The Internet Society (1999).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
























Ramakrishnan & Floyd          Experimental                     [Page 25]
^L