path: root/doc/rfc/rfc3165.txt

Network Working Group                                            D. Levi
Request for Comments: 3165                               Nortel Networks
Obsoletes: 2592                                         J. Schoenwaelder
Category: Standards Track                                TU Braunschweig
                                                             August 2001


                 Definitions of Managed Objects for the
                    Delegation of Management Scripts

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2001).  All Rights Reserved.

Abstract

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in the Internet community.
   In particular, it describes a set of managed objects that allow the
   delegation of management scripts to distributed managers.























Levi & Schoenwaelder        Standards Track                     [Page 1]
^L
RFC 3165                       Script MIB                    August 2001


Table of Contents

   1 Introduction .................................................    3
   2 The SNMP Management Framework ................................    3
   3 Overview .....................................................    4
   3.1 Terms ......................................................    5
   4 Requirements and Design Issues ...............................    6
   4.1 Script Languages ...........................................    6
   4.2 Script Transfer ............................................    7
   4.3 Script Execution ...........................................    8
   5 Structure of the MIB .........................................    9
   5.1 Language Group .............................................    9
   5.2 Script Group ...............................................   10
   5.3 Code Group .................................................   11
   5.4 Launch Group ...............................................   11
   5.5 Run Group ..................................................   11
   6 Definitions ..................................................   12
   7 Usage Examples ...............................................   49
   7.1 Pushing a Script via SNMP ..................................   49
   7.2 Pulling a Script from a URL ................................   50
   7.3 Modifying an Existing Script ...............................   50
   7.4 Removing an Existing Script ................................   51
   7.5 Creating a Launch Button ...................................   51
   7.6 Launching a Script .........................................   52
   7.7 Suspending a Running Script ................................   52
   7.8 Resuming a Suspended Script ................................   53
   7.9 Terminating a Running Script ...............................   53
   7.10 Removing a Terminated Script ..............................   54
   7.11 Removing a Launch Button ..................................   54
   8 VACM Configuration Examples ..................................   54
   8.1 Sandbox for Guests .........................................   55
   8.2 Sharing Scripts ............................................   55
   8.3 Emergency Scripts ..........................................   56
   9 IANA Considerations ..........................................   57
   10 Security Considerations .....................................   57
   11 Intellectual Property .......................................   59
   12 Changes from RFC 2592 .......................................   59
   13 Acknowledgments .............................................   61
   14 References ..................................................   61
   15 Editors' Addresses ..........................................   63
   16 Full Copyright Statement ....................................   64










Levi & Schoenwaelder        Standards Track                     [Page 2]
^L
RFC 3165                       Script MIB                    August 2001


1.  Introduction

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in the Internet community.
   In particular, it describes a set of managed objects that allow the
   delegation of management scripts to distributed managers.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

2.  The SNMP Management Framework

   The SNMP Management Framework presently consists of five major
   components:

   o  An overall architecture, described in RFC 2571 [RFC2571].

   o  Mechanisms for describing and naming objects and events for the
      purpose of management.  The first version of this Structure of
      Management Information (SMI) is called SMIv1 and described in STD
      16, RFC 1155 [RFC1155], STD 16, RFC 1212 [RFC1212] and RFC 1215
      [RFC1215].  The second version, called SMIv2, is described in STD
      58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC
      2580 [RFC2580].

   o  Message protocols for transferring management information.  The
      first version of the SNMP message protocol is called SNMPv1 and
      described in STD 15, RFC 1157 [RFC1157].  A second version of the
      SNMP message protocol, which is not an Internet standards track
      protocol, is called SNMPv2c and described in RFC 1901 [RFC1901]
      and RFC 1906 [RFC1906].  The third version of the message protocol
      is called SNMPv3 and described in RFC 1906 [RFC1906], RFC 2572
      [RFC2572] and RFC 2574 [RFC2574].

   o  Protocol operations for accessing management information.  The
      first set of protocol operations and associated PDU formats is
      described in STD 15, RFC 1157 [RFC1157].  A second set of protocol
      operations and associated PDU formats is described in RFC 1905
      [RFC1905].

   o  A set of fundamental applications described in RFC 2573 [RFC2573]
      and the view-based access control mechanism described in RFC 2575
      [RFC2575].

   A more detailed introduction to the current SNMP Management Framework
   can be found in RFC 2570 [RFC2570].




Levi & Schoenwaelder        Standards Track                     [Page 3]
^L
RFC 3165                       Script MIB                    August 2001


   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  Objects in the MIB are
   defined using the mechanisms defined in the SMI.

   This memo specifies a MIB module that is compliant to the SMIv2.  A
   MIB conforming to the SMIv1 can be produced through the appropriate
   translations.  The resulting translated MIB must be semantically
   equivalent, except where objects or events are omitted because no
   translation is possible (use of Counter64).  Some machine readable
   information in SMIv2 will be converted into textual descriptions in
   SMIv1 during the translation process.  However, this loss of machine
   readable information is not considered to change the semantics of the
   MIB.

3.  Overview

   The Script MIB module defined in this memo can be used to delegate
   management functions to distributed managers.  Management functions
   are defined as management scripts written in a management scripting
   language.  This MIB makes no assumptions about the language itself
   and even allows distribution of compiled native code, if an
   implementation is able to execute native code under the control of
   this MIB.

   The Script MIB defines a standard interface for the delegation of
   management functions based on the Internet management framework.  In
   particular, it provides the following capabilities:

   1. Capabilities to transfer management scripts to a distributed
      manager.

   2. Capabilities for initiating, suspending, resuming and terminating
      management scripts.

   3. Capabilities to transfer arguments for management scripts.

   4. Capabilities to monitor and control running management scripts.

   5. Capabilities to transfer the results produced by running
      management scripts.

   This memo does not address any additional topics like the generation
   of notifications or how to address remote agents from a Script MIB
   implementation.







Levi & Schoenwaelder        Standards Track                     [Page 4]
^L
RFC 3165                       Script MIB                    August 2001


3.1.  Terms

   This section defines the terms used throughout this memo.

   o  A `distributed manager' is a processing entity which is capable of
      performing network management functions.  For the scope of this
      memo, a distributed manager is assumed to implement the Script
      MIB.

   o  A `higher-level manager', or just `manager', is a processing
      entity or human who initiates and controls the operations
      performed by one or more distributed managers.

   o  A `management script' is a set of instructions written in an
      executable language which implements a management function.

   o  A `management scripting language' is a language used to write
      management scripts.  The term scripting language does not imply
      that the language must have the characteristics of scripting
      languages (e.g., string orientation, interpretation, weak typing).
      The MIB defined in this memo also allows to control management
      scripts written in arbitrary compiled system programming
      languages.

   o  A `distributed manager' can be decomposed into an `SNMP entity'
      which implements the Script MIB defined in this memo and the `
      runtime system' that executes scripts.  The Script MIB sees the
      runtime system as the managed resource which is controlled by the
      MIB.

      The runtime system can act as an SNMP application, according to
      the SNMP architecture defined in RFC 2571 [RFC2571].  For example,
      a runtime system which sends SNMP requests to other SNMP entities
      will act as a command generator application.  The SNMP
      applications in the runtime system may use the same SNMP engine
      which also serves the command responder application used to
      implement the Script MIB, but they are not required to do so.

   o  A `launch button' is the conceptual button used to start the
      execution of a management script.  It assigns control parameters
      to a management script.  In particular, it defines the ownership
      of the scripts started from a launch button.  The ownership can be
      used by the language runtime system to enforce security profiles
      on a running management script.







Levi & Schoenwaelder        Standards Track                     [Page 5]
^L
RFC 3165                       Script MIB                    August 2001


4.  Requirements and Design Issues

   This section discusses some general requirements that have influenced
   the design of the Script MIB.

   o  The Script MIB must not make any assumptions about specific
      languages or runtime systems.

   o  The Script MIB must provide mechanisms that help to avoid new
      management problems (e.g., script version problems).

   o  The Script MIB must provide SNMP interfaces to all functions
      required to delegate management scripts.  However, other protocols
      might be used in addition if they provide a significant
      improvement in terms of convenience for implementation or
      performance.

   o  The Script MIB must be organized so that access can be controlled
      effectively by using view-based access control [RFC2575].

   The following sections discuss some design issues in more detail.

4.1.  Script Languages

   The Script MIB defined in this memo makes no assumption about the
   script language.  This MIB can therefore be used in combination with
   different languages (such as Tcl or Java) and/or different versions
   of the same language.  No assumptions are made about the format in
   which management scripts are transferred.

   The Script MIB provides access to information about the language
   versions supported by a Script MIB implementation so that a manager
   can learn about the capabilities provided by an implementation.
   Languages and language versions are identified as follows:

   1. The language is identified by an object identifier.  Object
      identifier for well-known languages will be registered by the
      Internet Assigned Numbers Authority (IANA).  Enterprise specific
      languages can also be registered in the enterprise specific OID
      subtree.

   2. A particular version of a language is identified by a language
      version number.  The combination of a language object identifier
      and a language version is in most cases sufficient to decide
      whether a script can be executed or not.






Levi & Schoenwaelder        Standards Track                     [Page 6]
^L
RFC 3165                       Script MIB                    August 2001


   3. Different implementations of the same language version might have
      differences due to ambiguities in the language definition or
      additional language features provided by an implementor.  An
      additional object identifier value is provided which identifies
      the organization which provides the implementation of a language.
      This might be used by scripts that require a particular
      implementation of a language.

   4. Finally, there might be different versions of a language
      implementation.  A version number for the language implementation
      is provided so that the manager can also distinguish between
      different implementations from the same organization of a
      particular language version.

   The version numbers can either be used by a manager to select the
   language version required to execute a particular script or to select
   a script that fits the language versions supported by a particular
   Script MIB implementation.

   An additional table lists language extensions that provide features
   not provided by the core language.  Language extensions are usually
   required to turn a general purpose language into a management
   language.  In many cases, language extensions will come in the form
   of libraries that provide capabilities like sending SNMP requests to
   remote SNMP agents or accessing the local MIB instrumentation.  Every
   extension is associated with a language and carries its own version
   numbers.

4.2.  Script Transfer

   There are two different ways to transfer management scripts to a
   distributed manager.  The first approach requires that the manager
   pushes the script to the distributed manager.  This is therefore
   called the `push model'.  The second approach is the `pull model'
   where the manager tells the distributed manager the location of the
   script and the distributed manager retrieves the script itself.

   The MIB defined in this memo supports both models.  The `push model'
   is realized by a table which allows a manager to write scripts by
   sending a sequence of SNMP set requests.  The script can be split
   into several fragments in order to deal with SNMP message size
   limitations.

   The `pull model' is realized by the use of Uniform Resource Locators
   (URLs) [RFC2396] that point to the script source.  The manager writes
   the URL which points to the script source to the distributed manager





Levi & Schoenwaelder        Standards Track                     [Page 7]
^L
RFC 3165                       Script MIB                    August 2001


   by sending an SNMP set request.  The distributed manager is then
   responsible for retrieving the document using the protocol specified
   in the URL.  This allows the use of protocols like FTP [RFC959] or
   HTTP [RFC2616] to transfer large management scripts efficiently.

   The Script MIB also allows management scripts that are hard-wired
   into the Script MIB implementation.  Built-in scripts can either be
   implemented in a language runtime system, or they can be built
   natively into the Script MIB implementation.  The implementation of
   the `push model' or the `pull model' is not required.

   Scripts can be stored in non-volatile storage.  This allows a
   distributed manager to restart scripts if it is restarted (off-line
   restart).  A manager is not required to push scripts back into the
   distributed manager after a restart if the script is backed up in
   non-volatile storage.

   Every script is identified by an administratively assigned name.
   This name may be used to derive the name which is used to access the
   script in non-volatile storage.  This mapping is implementation
   specific.  However, the mapping must ensure that the Script MIB
   implementation can handle scripts with the same administrative name
   owned by different managers.  One way to achieve this is to use the
   script owner in addition to the script name in order to derive the
   internal name used to refer to a particular script in non-volatile
   storage.

4.3.  Script Execution

   The Script MIB permits execution of several instances of the same or
   different management scripts.  Script arguments are passed as OCTET
   STRING values.  Scripts return a single result value which is also an
   OCTET STRING value.  The semantic interpretation of result values is
   left to the invoking manager or other management scripts.  A script
   invoker must understand the format and semantics of both the
   arguments and the results of the scripts that it invokes.

   Scripts can also export complex results through a MIB interface.
   This allows a management application to access and use script results
   in the same manner as it processes any other MIB data.  However, the
   Script MIB does not provide any special support for the
   implementation of MIBs through scripts.

   Runtime errors terminate active scripts.  An exit code and a human
   readable error message is left in the MIB.  A notification containing
   the exit code, the error message and a timestamp is generated when a
   script terminates with an error exit code.




Levi & Schoenwaelder        Standards Track                     [Page 8]
^L
RFC 3165                       Script MIB                    August 2001


   Script arguments and results do not have any size limitations other
   than the limits imposed by the SMI and the SNMP protocol.  However,
   implementations of this MIB might have further restrictions.  A
   script designer might therefore choose to return the results via
   other mechanisms if the script results can be very large.  One
   possibility is to return a URL as a script result which points to the
   file containing the script output.

   Executing scripts have a status object attached which allows script
   execution to be suspended, resumed, or aborted.  The precise
   semantics of the suspend and resume operations are language and
   runtime system dependent.  Some runtime systems may choose to not
   implement the suspend/resume operations.

   A history of finished scripts is kept in the MIB.  A script invoker
   can collect results at a later point in time (offline operation).
   Control objects can be used to control how entries in the history are
   aged out if the table fills up.

5.  Structure of the MIB

   This section presents the structure of the MIB.  The objects are
   arranged into the following groups:

   o  language group (smLangTable, smExtsnTable)

   o  script group (smScriptTable)

   o  script code group (smCodeTable)

   o  script launch group (smLaunchTable)

   o  running script group (smRunTable)

5.1.  Language Group

   The smLanguageGroup is used to provide information about the
   languages and the language extensions supported by a Script MIB
   implementation.  This group includes two tables.  The smLangTable
   lists all languages supported by a Script MIB implementation and the
   smExtsnTable lists the extensions that are available for a given
   language.









Levi & Schoenwaelder        Standards Track                     [Page 9]
^L
RFC 3165                       Script MIB                    August 2001


5.2.  Script Group

   The smScriptGroup consists of a single table, called the
   smScriptTable.  The smScriptTable lists all scripts known to a Script
   MIB implementation.  The smScriptTable contains objects that allow
   the following operations:

   o  download scripts from a URL (pull model)

   o  read scripts from local non-volatile storage

   o  store scripts in local non-volatile storage

   o  delete scripts from local non-volatile storage

   o  list permanent scripts (that can not be changed or removed)

   o  read and modify the script status (enabled, disabled, editing)

   A status object called smScriptOperStatus allows a manager to obtain
   the current status of a script.  It is also used to provide an error
   indication if an attempt to invoke one of the operations listed above
   fails.  The status change of a script can be requested by modifying
   the associated smScriptAdminStatus object.

   The source of a script is defined by the smScriptSource object.  This
   object may contain a URL pointing to a remote location which provides
   access to the management script.  The script source is read from the
   smCodeTable (described below) or from non-volatile storage if the
   smScriptSource object contains an empty URL.  The smScriptStorageType
   object is used to distinguish between scripts read from non-volatile
   storage and scripts read from the smCodeTable.

   Scripts are automatically loaded once the smScriptAdminStatus object
   is set to `enabled'.  Loading a script includes retrieving the script
   (probably from a remote location), compiling the script for languages
   that require a compilation step, and making the code available to the
   runtime system.  The smScriptOperStatus object is used to indicate
   the status of the loading process.  This object will start in the
   state `retrieving', switch to the state `compiling' and finally reach
   the state `enabled'.  Errors during the retrieval or compilation
   phase will result in an error state such as `compilationFailed'.









Levi & Schoenwaelder        Standards Track                    [Page 10]
^L
RFC 3165                       Script MIB                    August 2001


5.3.  Code Group

   The smCodeGroup consists of a single table, called the smCodeTable,
   which provides the ability to transfer and modify scripts via SNMP
   set requests.  In particular, the smCodeTable allows the following
   operations:

   o  download scripts via SNMP (push model)

   o  modify scripts via SNMP (editing)

   The smCodeTable lists the code of a script.  A script can be
   fragmented over multiple rows of the smCodeTable in order to handle
   SNMP message size limitations.  Modifications of the smCodeTable are
   only possible if the associated smScriptOperStatus object has the
   value `editing'.  The Script MIB implementation reloads the modified
   script code once the smScriptOperStatus changes to `enabled' again.

   The implementation of the smCodeGroup is optional.

5.4.  Launch Group

   The smLaunchGroup contains a single table, the smLaunchTable.  An
   entry in the smLaunchTable represents a launch button which can be
   used to start a script.  The smLaunchTable allows the following
   operations:

   o  associate a script with an owner used during script execution

   o  provide arguments and parameters for script invocation

   o  invoke scripts with a single set operation

   The smLaunchTable describes scripts and their parameters that are
   ready to be launched.  An entry in the smLaunchTable attaches an
   argument to a script and control values which, for example, define
   the maximum number of times that a script invoked from a particular
   row in the smLaunchTable may be running concurrently.

   An entry in the smLaunchTable also defines the owner which will be
   used to associate permissions with the script execution.

5.5.  Run Group

   The smRunGroup contains a single table, called the smRunTable, which
   lists all scripts that are currently running or have terminated
   recently.  The smRunTable contains objects that allow the following
   operations:



Levi & Schoenwaelder        Standards Track                    [Page 11]
^L
RFC 3165                       Script MIB                    August 2001


   o  retrieve status information from running scripts

   o  control running scripts (suspend, resume, abort)

   o  retrieve results from recently terminated scripts

   o  control the remaining maximum lifetime of a running script

   o  control how long script results are accessible

   Every row in the smRunTable contains the argument passed during
   script invocation, the result produced by the script and the script
   exit code.  The smRunTable also provides information about the
   current run state as well as start and end time-stamps.  There are
   three writable objects in the smRunTable.  The smRunLifeTime object
   defines the maximum time a running script may run before it is
   terminated by the Script MIB implementation.  The smRunExpireTime
   object defines the time that a completed script can stay in the
   smRunTable before it is aged out.  The smRunControl object allows
   running scripts to be suspended, resumed, or aborted.

6.  Definitions

   DISMAN-SCRIPT-MIB DEFINITIONS ::= BEGIN

   IMPORTS
       MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
       Integer32, Unsigned32, mib-2
           FROM SNMPv2-SMI

       RowStatus, TimeInterval, DateAndTime, StorageType, DisplayString
           FROM SNMPv2-TC

       MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
           FROM SNMPv2-CONF

       SnmpAdminString
           FROM SNMP-FRAMEWORK-MIB;

   scriptMIB MODULE-IDENTITY
       LAST-UPDATED "200108210000Z"
       ORGANIZATION "IETF Distributed Management Working Group"
       CONTACT-INFO
           "WG EMail:  disman@dorothy.bmc.com
            Subscribe: disman-request@dorothy.bmc.com

            Chair:     Randy Presuhn
                       BMC Software, Inc.



Levi & Schoenwaelder        Standards Track                    [Page 12]
^L
RFC 3165                       Script MIB                    August 2001


            Postal:    Office 1-3141
                       2141 North First Street
                       San Jose,  California 95131
                       USA
            EMail:     rpresuhn@bmc.com
            Phone:     +1 408 546-1006

            Editor:    David B. Levi
                       Nortel Networks
            Postal:    4401 Great America Parkway
                       Santa Clara, CA 95052-8185
                       USA
            EMail:     dlevi@nortelnetworks.com
            Phone:     +1 423 686 0432

            Editor:    Juergen Schoenwaelder
                       TU Braunschweig
            Postal:    Bueltenweg 74/75
                       38106 Braunschweig
                       Germany
            EMail:     schoenw@ibr.cs.tu-bs.de
            Phone:     +49 531 391-3283"
       DESCRIPTION
           "This MIB module defines a set of objects that allow to
            delegate management scripts to distributed managers."
       REVISION    "200108210000Z"
       DESCRIPTION
           "Revised version, published as RFC 3165.

            This revision introduces several new objects: smScriptError,
            smScriptLastChange, smLaunchError, smLaunchLastChange,
            smLaunchRowExpireTime, smRunResultTime, and smRunErrorTime.

            The following existing objects were updated: the maximum
            value of smRunLifeTime now disables the timer, an
            autostart value was added to the smLaunchAdminStatus
            object, and a new expired state was added to the
            smLaunchOperStatus object.

            A new smScriptException notification has been added to
            support runtime error notifications.

            Created new conformance and compliance statements that
            take care of the new objects and notifications.

            Clarifications have been added in several places to remove
            ambiguities or contradictions that were discovered and
            reported by implementors."



Levi & Schoenwaelder        Standards Track                    [Page 13]
^L
RFC 3165                       Script MIB                    August 2001


       REVISION    "199902221800Z"
       DESCRIPTION
           "Initial version, published as RFC 2592."
       ::= { mib-2 64 }

   --
   -- The groups defined within this MIB module:
   --

   smObjects       OBJECT IDENTIFIER ::= { scriptMIB 1 }
   smNotifications OBJECT IDENTIFIER ::= { scriptMIB 2 }
   smConformance   OBJECT IDENTIFIER ::= { scriptMIB 3 }

   --
   -- Script language and language extensions.
   --
   -- This group defines tables which list the languages and the
   -- language extensions supported by a Script MIB implementation.
   -- Languages are uniquely identified by object identifier values.
   --

   smLangTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF SmLangEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "This table lists supported script languages."
       ::= { smObjects 1 }

   smLangEntry OBJECT-TYPE
       SYNTAX      SmLangEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "An entry describing a particular language."
       INDEX { smLangIndex }
       ::= { smLangTable 1 }

   SmLangEntry ::= SEQUENCE {
       smLangIndex         Integer32,
       smLangLanguage      OBJECT IDENTIFIER,
       smLangVersion       SnmpAdminString,
       smLangVendor        OBJECT IDENTIFIER,
       smLangRevision      SnmpAdminString,
       smLangDescr         SnmpAdminString
   }

   smLangIndex OBJECT-TYPE



Levi & Schoenwaelder        Standards Track                    [Page 14]
^L
RFC 3165                       Script MIB                    August 2001


       SYNTAX      Integer32 (1..2147483647)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The locally arbitrary, but unique identifier associated
            with this language entry.

            The value is expected to remain constant at least from one
            re-initialization of the entity's network management system
            to the next re-initialization.

            Note that the data type and the range of this object must
            be consistent with the definition of smScriptLanguage."
       ::= { smLangEntry 1 }

   smLangLanguage OBJECT-TYPE
       SYNTAX      OBJECT IDENTIFIER
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The globally unique identification of the language."
       ::= { smLangEntry 2 }

   smLangVersion OBJECT-TYPE
       SYNTAX      SnmpAdminString (SIZE (0..32))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The version number of the language. The zero-length string
            shall be used if the language does not have a version
            number.

            It is suggested that the version number consist of one or
            more decimal numbers separated by dots, where the first
            number is called the major version number."
       ::= { smLangEntry 3 }

   smLangVendor OBJECT-TYPE
       SYNTAX      OBJECT IDENTIFIER
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "An object identifier which identifies the vendor who
            provides the implementation of the language. This object
            identifier SHALL point to the object identifier directly
            below the enterprise object identifier {1 3 6 1 4 1}
            allocated for the vendor. The value must be the object
            identifier {0 0} if the vendor is not known."



Levi & Schoenwaelder        Standards Track                    [Page 15]
^L
RFC 3165                       Script MIB                    August 2001


       ::= { smLangEntry 4 }

   smLangRevision OBJECT-TYPE
       SYNTAX      SnmpAdminString (SIZE (0..32))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The version number of the language implementation.
            The value of this object must be an empty string if
            version number of the implementation is unknown.

            It is suggested that the value consist of one or more
            decimal numbers separated by dots, where the first
            number is called the major version number."
       ::= { smLangEntry 5 }

   smLangDescr OBJECT-TYPE
       SYNTAX      SnmpAdminString
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "A textual description of the language."
       ::= { smLangEntry 6 }


   smExtsnTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF SmExtsnEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "This table lists supported language extensions."
       ::= { smObjects 2 }

   smExtsnEntry OBJECT-TYPE
       SYNTAX      SmExtsnEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "An entry describing a particular language extension."
       INDEX { smLangIndex, smExtsnIndex }
       ::= { smExtsnTable 1 }

   SmExtsnEntry ::= SEQUENCE {
       smExtsnIndex        Integer32,
       smExtsnExtension    OBJECT IDENTIFIER,
       smExtsnVersion      SnmpAdminString,
       smExtsnVendor       OBJECT IDENTIFIER,
       smExtsnRevision     SnmpAdminString,



Levi & Schoenwaelder        Standards Track                    [Page 16]
^L
RFC 3165                       Script MIB                    August 2001


       smExtsnDescr        SnmpAdminString
   }

   smExtsnIndex OBJECT-TYPE
       SYNTAX      Integer32 (1..2147483647)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The locally arbitrary, but unique identifier associated
            with this language extension entry.

            The value is expected to remain constant at least from one
            re-initialization of the entity's network management system
            to the next re-initialization."
       ::= { smExtsnEntry 1}

   smExtsnExtension OBJECT-TYPE
       SYNTAX      OBJECT IDENTIFIER
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The globally unique identification of the language
            extension."
       ::= { smExtsnEntry 2 }

   smExtsnVersion OBJECT-TYPE
       SYNTAX      SnmpAdminString (SIZE (0..32))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The version number of the language extension.
            It is suggested that the version number consist of one or
            more decimal numbers separated by dots, where the first
            number is called the major version number."
       ::= { smExtsnEntry 3 }

   smExtsnVendor OBJECT-TYPE
       SYNTAX      OBJECT IDENTIFIER
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "An object identifier which identifies the vendor who
            provides the implementation of the extension. The
            object identifier value should point to the OID node
            directly below the enterprise OID {1 3 6 1 4 1}
            allocated for the vendor. The value must by the object
            identifier {0 0} if the vendor is not known."
       ::= { smExtsnEntry 4 }



Levi & Schoenwaelder        Standards Track                    [Page 17]
^L
RFC 3165                       Script MIB                    August 2001


   smExtsnRevision OBJECT-TYPE
       SYNTAX      SnmpAdminString (SIZE (0..32))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The version number of the extension implementation.
            The value of this object must be an empty string if
            version number of the implementation is unknown.

            It is suggested that the value consist of one or more
            decimal numbers separated by dots, where the first
            number is called the major version number."
       ::= { smExtsnEntry 5 }

   smExtsnDescr OBJECT-TYPE
       SYNTAX      SnmpAdminString
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "A textual description of the language extension."
       ::= { smExtsnEntry 6 }

   --
   -- Scripts known by the Script MIB implementation.
   --
   -- This group defines a table which lists all known scripts.
   -- Scripts can be added and removed through manipulation of the
   -- smScriptTable.
   --

   smScriptObjects OBJECT IDENTIFIER ::= { smObjects 3 }

   smScriptTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF SmScriptEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "This table lists and describes locally known scripts."
       ::= { smScriptObjects 1 }

   smScriptEntry OBJECT-TYPE
       SYNTAX      SmScriptEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "An entry describing a particular script. Every script that
            is stored in non-volatile memory is required to appear in
            this script table."



Levi & Schoenwaelder        Standards Track                    [Page 18]
^L
RFC 3165                       Script MIB                    August 2001


       INDEX { smScriptOwner, smScriptName }
       ::= { smScriptTable 1 }

   SmScriptEntry ::= SEQUENCE {
       smScriptOwner       SnmpAdminString,
       smScriptName        SnmpAdminString,
       smScriptDescr       SnmpAdminString,
       smScriptLanguage    Integer32,
       smScriptSource      DisplayString,
       smScriptAdminStatus INTEGER,
       smScriptOperStatus  INTEGER,
       smScriptStorageType StorageType,
       smScriptRowStatus   RowStatus,
       smScriptError       SnmpAdminString,
       smScriptLastChange  DateAndTime
   }

   smScriptOwner OBJECT-TYPE
       SYNTAX      SnmpAdminString (SIZE (0..32))
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The manager who owns this row in the smScriptTable."
       ::= { smScriptEntry 1 }

   smScriptName OBJECT-TYPE
       SYNTAX      SnmpAdminString (SIZE (1..32))
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The locally-unique, administratively assigned name for this
            script. This object allows an smScriptOwner to have multiple
            entries in the smScriptTable.

            This value of this object may be used to derive the name
            (e.g. a file name) which is used by the Script MIB
            implementation to access the script in non-volatile
            storage. The details of this mapping are implementation
            specific. However, the mapping needs to ensure that scripts
            created by different owners with the same script name do not
            map to the same name in non-volatile storage."
       ::= { smScriptEntry 2 }

   smScriptDescr OBJECT-TYPE
       SYNTAX      SnmpAdminString
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION



Levi & Schoenwaelder        Standards Track                    [Page 19]
^L
RFC 3165                       Script MIB                    August 2001


           "A description of the purpose of the script."
       ::= { smScriptEntry 3 }

   smScriptLanguage OBJECT-TYPE
       SYNTAX      Integer32 (0..2147483647)
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The value of this object type identifies an entry in the
            smLangTable which is used to execute this script.
            The special value 0 may be used by hard-wired scripts
            that can not be modified and that are executed by
            internal functions.

            Set requests to change this object are invalid if the
            value of smScriptOperStatus is `enabled' or `compiling'
            and will result in an inconsistentValue error.

            Note that the data type and the range of this object must
            be consistent with the definition of smLangIndex."
       ::= { smScriptEntry 4 }

   smScriptSource OBJECT-TYPE
       SYNTAX      DisplayString
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "This object either contains a reference to the script
            source or an empty string. A reference must be given
            in the form of a Uniform Resource Locator (URL) as
            defined in RFC 2396. The allowed character sets and the
            encoding rules defined in RFC 2396 section 2 apply.

            When the smScriptAdminStatus object is set to `enabled',
            the Script MIB implementation will `pull' the script
            source from the URL contained in this object if the URL
            is not empty.

            An empty URL indicates that the script source is loaded
            from local storage. The script is read from the smCodeTable
            if the value of smScriptStorageType is volatile. Otherwise,
            the script is read from non-volatile storage.

            Note: This document does not mandate implementation of any
            specific URL scheme. An attempt to load a script from a
            nonsupported URL scheme will cause the smScriptOperStatus
            to report an `unknownProtocol' error.




Levi & Schoenwaelder        Standards Track                    [Page 20]
^L
RFC 3165                       Script MIB                    August 2001


            Set requests to change this object are invalid if the
            value of smScriptOperStatus is `enabled', `editing',
            `retrieving' or `compiling' and will result in an
            inconsistentValue error."
       DEFVAL { ''H }
       ::= { smScriptEntry 5 }

   smScriptAdminStatus OBJECT-TYPE
       SYNTAX      INTEGER {
                       enabled(1),
                       disabled(2),
                       editing(3)
                   }
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The value of this object indicates the desired status of
            the script. See the definition of smScriptOperStatus for
            a description of the values.

            When the smScriptAdminStatus object is set to `enabled' and
            the smScriptOperStatus is `disabled' or one of the error
            states, the Script MIB implementation will `pull' the script
            source from the URL contained in the smScriptSource object
            if the URL is not empty."
       DEFVAL { disabled }
       ::= { smScriptEntry 6 }

   smScriptOperStatus OBJECT-TYPE
       SYNTAX      INTEGER {
                       enabled(1),
                       disabled(2),
                       editing(3),
                       retrieving(4),
                       compiling(5),
                       noSuchScript(6),
                       accessDenied(7),
                       wrongLanguage(8),
                       wrongVersion(9),
                       compilationFailed(10),
                       noResourcesLeft(11),
                       unknownProtocol(12),
                       protocolFailure(13),
                       genericError(14)
                   }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION



Levi & Schoenwaelder        Standards Track                    [Page 21]
^L
RFC 3165                       Script MIB                    August 2001


           "The actual status of the script in the runtime system. The
            value of this object is only meaningful when the value of
            the smScriptRowStatus object is `active'.

            The smScriptOperStatus object may have the following values:

            - `enabled' indicates that the script is available and can
               be started by a launch table entry.

            - `disabled' indicates that the script can not be used.

            - `editing' indicates that the script can be modified in the
              smCodeTable.

            - `retrieving' indicates that the script is currently being
              loaded from non-volatile storage or a remote system.

            - `compiling' indicates that the script is currently being
              compiled by the runtime system.

            - `noSuchScript' indicates that the script does not exist
              at the smScriptSource.

            - `accessDenied' indicates that the script can not be loaded
              from the smScriptSource due to a lack of permissions.

            - `wrongLanguage' indicates that the script can not be
               loaded from the smScriptSource because of a language
               mismatch.

            - `wrongVersion' indicates that the script can not be loaded
              from the smScriptSource because of a language version
              mismatch.

            - `compilationFailed' indicates that the compilation failed.

            - `noResourcesLeft' indicates that the runtime system does
              not have enough resources to load the script.

            - `unknownProtocol' indicates that the script could not be
              loaded from the smScriptSource because the requested
              protocol is not supported.

            - `protocolFailure' indicates that the script could not be
              loaded from the smScriptSource because of a protocol
              failure.

            - `genericError' indicates that the script could not be



Levi & Schoenwaelder        Standards Track                    [Page 22]
^L
RFC 3165                       Script MIB                    August 2001


              loaded due to an error condition not listed above.

            The `retrieving' and `compiling' states are transient states
            which will either lead to one of the error states or the
            `enabled' state. The `disabled' and `editing' states are
            administrative states which are only reached by explicit
            management operations.

            All launch table entries that refer to this script table
            entry shall have an smLaunchOperStatus value of `disabled'
            when the value of this object is not `enabled'."
       DEFVAL { disabled }
       ::= { smScriptEntry 7 }

   smScriptStorageType OBJECT-TYPE
       SYNTAX      StorageType
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "This object defines whether this row and the script
            controlled by this row are kept in volatile storage and
            lost upon reboot or if this row is backed up by
            non-volatile or permanent storage.

            The storage type of this row always complies with the value
            of this entry if the value of the corresponding RowStatus
            object is `active'.

            However, the storage type of the script controlled by this
            row may be different, if the value of this entry is
            `non-volatile'. The script controlled by this row is written
            into local non-volatile storage if the following condition
            becomes true:

            (a) the URL contained in the smScriptSource object is empty
                and
            (b) the smScriptStorageType is `nonVolatile'
                and
            (c) the smScriptOperStatus is `enabled'

            Setting this object to `volatile' removes a script from
            non-volatile storage if the script controlled by this row
            has been in non-volatile storage before. Attempts to set
            this object to permanent will always fail with an
            inconsistentValue error.

            The value of smScriptStorageType is only meaningful if the
            value of the corresponding RowStatus object is `active'.



Levi & Schoenwaelder        Standards Track                    [Page 23]
^L
RFC 3165                       Script MIB                    August 2001


            If smScriptStorageType has the value permanent(4), then all
            objects whose MAX-ACCESS value is read-create must be
            writable, with the exception of the smScriptStorageType and
            smScriptRowStatus objects, which shall be read-only."
       DEFVAL { volatile }
       ::= { smScriptEntry 8 }

   smScriptRowStatus OBJECT-TYPE
       SYNTAX      RowStatus
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "A control that allows entries to be added and removed from
            this table.

            Changing the smScriptRowStatus from `active' to
            `notInService' will remove the associated script from the
            runtime system.

            Deleting conceptual rows from this table may affect the
            deletion of other resources associated with this row. For
            example, a script stored in non-volatile storage may be
            removed from non-volatile storage.

            An entry may not exist in the `active' state unless all
            required objects in the entry have appropriate values. Rows
            that are not complete or not in service are not known by the
            script runtime system.

            Attempts to `destroy' a row or to set a row `notInService'
            while the smScriptOperStatus is `enabled' will result in an
            inconsistentValue error.

            Attempts to `destroy' a row or to set a row `notInService'
            where the value of the smScriptStorageType object is
            `permanent' or `readOnly' will result in an
            inconsistentValue error.

            The value of this object has no effect on whether other
            objects in this conceptual row can be modified."
       ::= { smScriptEntry 9 }

   smScriptError OBJECT-TYPE
       SYNTAX      SnmpAdminString
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "This object contains a descriptive error message if the



Levi & Schoenwaelder        Standards Track                    [Page 24]
^L
RFC 3165                       Script MIB                    August 2001


            transition into the operational status `enabled' failed.
            Implementations must reset the error message to a
            zero-length string when a new attempt to change the
            script status to `enabled' is started."
       DEFVAL { ''H }
       ::= { smScriptEntry 10 }

   smScriptLastChange OBJECT-TYPE
       SYNTAX      DateAndTime
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The date and time when this script table entry was last
            modified. The value '0000000000000000'H is returned if
            the script table entry has not yet been modified.

            Note that the resetting of smScriptError is not considered
            a change of the script table entry."
       DEFVAL { '0000000000000000'H }
       ::= { smScriptEntry 11 }

   --
   -- Access to script code via SNMP
   --
   -- The smCodeTable allows script code to be read and modified
   -- via SNMP.
   --

   smCodeTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF SmCodeEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "This table contains the script code for scripts that are
            written via SNMP write operations."
       ::= { smScriptObjects 2 }

   smCodeEntry OBJECT-TYPE
       SYNTAX      SmCodeEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "An entry describing a particular fragment of a script."
       INDEX { smScriptOwner, smScriptName, smCodeIndex }
       ::= { smCodeTable 1 }

   SmCodeEntry ::= SEQUENCE {
       smCodeIndex         Unsigned32,



Levi & Schoenwaelder        Standards Track                    [Page 25]
^L
RFC 3165                       Script MIB                    August 2001


       smCodeText          OCTET STRING,
       smCodeRowStatus     RowStatus
   }

   smCodeIndex OBJECT-TYPE
       SYNTAX      Unsigned32 (1..4294967295)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The index value identifying this code fragment."
       ::= { smCodeEntry 1 }

   smCodeText OBJECT-TYPE
       SYNTAX      OCTET STRING (SIZE (1..1024))
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The code that makes up a fragment of a script. The format
            of this code fragment depends on the script language which
            is identified by the associated smScriptLanguage object."
       ::= { smCodeEntry 2 }

   smCodeRowStatus OBJECT-TYPE
       SYNTAX      RowStatus
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "A control that allows entries to be added and removed from
            this table.

            The value of this object has no effect on whether other
            objects in this conceptual row can be modified."
       ::= { smCodeEntry 3 }

   --
   -- Script execution.
   --
   -- This group defines tables which allow script execution to be
   -- initiated, suspended, resumed, and terminated.  It also provides
   -- a mechanism for keeping a history of recent script executions
   -- and their results.
   --

   smRunObjects OBJECT IDENTIFIER ::= { smObjects 4 }

   smLaunchTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF SmLaunchEntry
       MAX-ACCESS  not-accessible



Levi & Schoenwaelder        Standards Track                    [Page 26]
^L
RFC 3165                       Script MIB                    August 2001


       STATUS      current
       DESCRIPTION
           "This table lists and describes scripts that are ready
            to be executed together with their parameters."
       ::= { smRunObjects 1 }

   smLaunchEntry OBJECT-TYPE
       SYNTAX      SmLaunchEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "An entry describing a particular executable script."
       INDEX { smLaunchOwner, smLaunchName }
       ::= { smLaunchTable 1 }

   SmLaunchEntry ::= SEQUENCE {
       smLaunchOwner               SnmpAdminString,
       smLaunchName                SnmpAdminString,
       smLaunchScriptOwner         SnmpAdminString,
       smLaunchScriptName          SnmpAdminString,
       smLaunchArgument            OCTET STRING,
       smLaunchMaxRunning          Unsigned32,
       smLaunchMaxCompleted        Unsigned32,
       smLaunchLifeTime            TimeInterval,
       smLaunchExpireTime          TimeInterval,
       smLaunchStart               Integer32,
       smLaunchControl             INTEGER,
       smLaunchAdminStatus         INTEGER,
       smLaunchOperStatus          INTEGER,
       smLaunchRunIndexNext        Integer32,
       smLaunchStorageType         StorageType,
       smLaunchRowStatus           RowStatus,
       smLaunchError               SnmpAdminString,
       smLaunchLastChange          DateAndTime,
       smLaunchRowExpireTime       TimeInterval
   }

   smLaunchOwner OBJECT-TYPE
       SYNTAX      SnmpAdminString (SIZE (0..32))
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The manager who owns this row in the smLaunchTable. Every
            instance of a running script started from a particular entry
            in the smLaunchTable (i.e. entries in the smRunTable) will
            be owned by the same smLaunchOwner used to index the entry
            in the smLaunchTable. This owner is not necessarily the same
            as the owner of the script itself (smLaunchScriptOwner)."



Levi & Schoenwaelder        Standards Track                    [Page 27]
^L
RFC 3165                       Script MIB                    August 2001


       ::= { smLaunchEntry 1 }

   smLaunchName OBJECT-TYPE
       SYNTAX      SnmpAdminString (SIZE (1..32))
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The locally-unique, administratively assigned name for this
            launch table entry. This object allows an smLaunchOwner to
            have multiple entries in the smLaunchTable. The smLaunchName
            is an arbitrary name that must be different from any other
            smLaunchTable entries with the same smLaunchOwner but can be
            the same as other entries in the smLaunchTable with
            different smLaunchOwner values. Note that the value of
            smLaunchName is not related in any way to the name of the
            script being launched."
       ::= { smLaunchEntry 2 }

   smLaunchScriptOwner OBJECT-TYPE
       SYNTAX      SnmpAdminString (SIZE (0..32))
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The value of this object in combination with the value of
            smLaunchScriptName identifies the script that can be
            launched from this smLaunchTable entry. Attempts to write
            this object will fail with an inconsistentValue error if
            the value of smLaunchOperStatus is `enabled'."
       ::= { smLaunchEntry 3 }

   smLaunchScriptName OBJECT-TYPE
       SYNTAX      SnmpAdminString (SIZE (0..32))
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The value of this object in combination with the value of
            the smLaunchScriptOwner identifies the script that can be
            launched from this smLaunchTable entry. The zero-length
            string may be used to point to a non-existing script.

            Attempts to write this object will fail with an
            inconsistentValue error if the value of smLaunchOperStatus
            is `enabled'."
       DEFVAL { ''H }
       ::= { smLaunchEntry 4 }

   smLaunchArgument OBJECT-TYPE
       SYNTAX      OCTET STRING



Levi & Schoenwaelder        Standards Track                    [Page 28]
^L
RFC 3165                       Script MIB                    August 2001


       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The argument supplied to the script. When a script is
            invoked, the value of this object is used to initialize
            the smRunArgument object."
       DEFVAL { ''H }
       ::= { smLaunchEntry 5 }

   smLaunchMaxRunning OBJECT-TYPE
       SYNTAX      Unsigned32 (1..4294967295)
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The maximum number of concurrently running scripts that may
            be invoked from this entry in the smLaunchTable. Lowering
            the current value of this object does not affect any scripts
            that are already executing."
       DEFVAL { 1 }
       ::= { smLaunchEntry 6 }

   smLaunchMaxCompleted OBJECT-TYPE
       SYNTAX      Unsigned32 (1..4294967295)
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The maximum number of finished scripts invoked from this
            entry in the smLaunchTable allowed to be retained in the
            smRunTable. Whenever the value of this object is changed
            and whenever a script terminates, entries in the smRunTable
            are deleted if necessary until the number of completed
            scripts is smaller than the value of this object. Scripts
            whose smRunEndTime value indicates the oldest completion
            time are deleted first."
       DEFVAL { 1 }
       ::= { smLaunchEntry 7 }

   smLaunchLifeTime OBJECT-TYPE
       SYNTAX      TimeInterval
       UNITS       "centi-seconds"
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The default maximum amount of time a script launched
            from this entry may run. The value of this object is used
            to initialize the smRunLifeTime object when a script is
            launched. Changing the value of an smLaunchLifeTime
            instance does not affect scripts previously launched from



Levi & Schoenwaelder        Standards Track                    [Page 29]
^L
RFC 3165                       Script MIB                    August 2001


            this entry."
       DEFVAL { 360000 }
       ::= { smLaunchEntry 8 }

   smLaunchExpireTime OBJECT-TYPE
       SYNTAX      TimeInterval
       UNITS       "centi-seconds"
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The default maximum amount of time information about a
            script launched from this entry is kept in the smRunTable
            after the script has completed execution.  The value of
            this object is used to initialize the smRunExpireTime
            object when a script is launched. Changing the value of an
            smLaunchExpireTime instance does not affect scripts
            previously launched from this entry."
       DEFVAL { 360000 }
       ::= { smLaunchEntry 9 }

   smLaunchStart OBJECT-TYPE
       SYNTAX      Integer32 (0..2147483647)
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "This object is used to start the execution of scripts.
            When retrieved, the value will be the value of smRunIndex
            for the last script that started execution by manipulating
            this object. The value will be zero if no script started
            execution yet.

            A script is started by setting this object to an unused
            smRunIndex value. A new row in the smRunTable will be
            created which is indexed by the value supplied by the
            set-request in addition to the value of smLaunchOwner and
            smLaunchName. An unused value can be obtained by reading
            the smLaunchRunIndexNext object.

            Setting this object to the special value 0 will start
            the script with a self-generated smRunIndex value. The
            consequence is that the script invoker has no reliable
            way to determine the smRunIndex value for this script
            invocation and that the invoker has therefore no way
            to obtain the results from this script invocation. The
            special value 0 is however useful for scheduled script
            invocations.

            If this object is set, the following checks must be



Levi & Schoenwaelder        Standards Track                    [Page 30]
^L
RFC 3165                       Script MIB                    August 2001


            performed:

            1) The value of the smLaunchOperStatus object in this
               entry of the smLaunchTable must be `enabled'.
            2) The values of smLaunchScriptOwner and
               smLaunchScriptName of this row must identify an
               existing entry in the smScriptTable.
            3) The value of smScriptOperStatus of this entry must
               be `enabled'.
            4) The principal performing the set operation must have
               read access to the script. This must be checked by
               calling the isAccessAllowed abstract service interface
               defined in RFC 2271 on the row in the smScriptTable
               identified by smLaunchScriptOwner and smLaunchScriptName.
               The isAccessAllowed abstract service interface must be
               called on all columnar objects in the smScriptTable with
               a MAX-ACCESS value different than `not-accessible'. The
               test fails as soon as a call indicates that access is
               not allowed.
            5) If the value provided by the set operation is not 0,
               a check must be made that the value is currently not
               in use. Otherwise, if the value provided by the set
               operation is 0, a suitable unused value must be
               generated.
            6) The number of currently executing scripts invoked
               from this smLaunchTable entry must be less than
               smLaunchMaxRunning.

            Attempts to start a script will fail with an
            inconsistentValue error if one of the checks described
            above fails.

            Otherwise, if all checks have been passed, a new entry
            in the smRunTable will be created indexed by smLaunchOwner,
            smLaunchName and the new value for smRunIndex. The value
            of smLaunchArgument will be copied into smRunArgument,
            the value of smLaunchLifeTime will be copied to
            smRunLifeTime, and the value of smLaunchExpireTime
            will be copied to smRunExpireTime.

            The smRunStartTime will be set to the current time and
            the smRunState will be set to `initializing' before the
            script execution is initiated in the appropriate runtime
            system.

            Note that the data type and the range of this object must
            be consistent with the smRunIndex object. Since this
            object might be written from the scheduling MIB, the



Levi & Schoenwaelder        Standards Track                    [Page 31]
^L
RFC 3165                       Script MIB                    August 2001


            data type Integer32 rather than Unsigned32 is used."
       DEFVAL { 0 }
       ::= { smLaunchEntry 10 }

   smLaunchControl OBJECT-TYPE
       SYNTAX      INTEGER {
                       abort(1),
                       suspend(2),
                       resume(3),
                       nop(4)
                   }
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "This object is used to request a state change for all
            running scripts in the smRunTable that were started from
            this row in the smLaunchTable.

            Setting this object to abort(1), suspend(2) or resume(3)
            will set the smRunControl object of all applicable rows
            in the smRunTable to abort(1), suspend(2) or resume(3)
            respectively. The phrase `applicable rows' means the set of
            rows which were created from this entry in the smLaunchTable
            and whose value of smRunState allows the corresponding
            state change as described in the definition of the
            smRunControl object. Setting this object to nop(4) has no
            effect.

            Attempts to set this object lead to an inconsistentValue
            error only if all implicated sets on all the applicable
            rows lead to inconsistentValue errors. It is not allowed
            to return an inconsistentValue error if at least one state
            change on one of the applicable rows was successful."
       DEFVAL { nop }
       ::= { smLaunchEntry 11 }

   smLaunchAdminStatus OBJECT-TYPE
       SYNTAX      INTEGER {
                       enabled(1),
                       disabled(2),
                       autostart(3)
                   }
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The value of this object indicates the desired status of
            this launch table entry. The values enabled(1) and
            autostart(3) both indicate that the launch table entry



Levi & Schoenwaelder        Standards Track                    [Page 32]
^L
RFC 3165                       Script MIB                    August 2001


            should transition into the operational enabled(1) state as
            soon as the associated script table entry is enabled(1).

            The value autostart(3) further indicates that the script
            is started automatically by conceptually writing the
            value 0 into the associated smLaunchStart object during
            the transition from the `disabled' into the `enabled'
            operational state. This is useful for scripts that are
            to be launched on system start-up."
       DEFVAL { disabled }
       ::= { smLaunchEntry 12 }

   smLaunchOperStatus OBJECT-TYPE
       SYNTAX      INTEGER {
                       enabled(1),
                       disabled(2),
                       expired(3)
                   }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The value of this object indicates the actual status of
            this launch table entry.  The smLaunchOperStatus object
            may have the following values:

            - `enabled' indicates that the launch table entry is
              available and can be used to start scripts.

            - `disabled' indicates that the launch table entry can
              not be used to start scripts.

            - `expired' indicates that the launch table entry can
              not be used to start scripts and will disappear as
              soon as all smRunTable entries associated with this
              launch table entry have disappeared.

            The value `enabled' requires that the smLaunchRowStatus
            object is active. The value `disabled' requires that there
            are no entries in the smRunTable associated with this
            smLaunchTable entry."
       DEFVAL { disabled }
       ::= { smLaunchEntry 13 }

   smLaunchRunIndexNext OBJECT-TYPE
       SYNTAX      Integer32 (1..2147483647)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION



Levi & Schoenwaelder        Standards Track                    [Page 33]
^L
RFC 3165                       Script MIB                    August 2001


           "This variable is used for creating rows in the smRunTable.
            The value of this variable is a currently unused value
            for smRunIndex, which can be written into the smLaunchStart
            object associated with this row to launch a script.

            The value returned when reading this variable must be unique
            for the smLaunchOwner and smLaunchName associated with this
            row. Subsequent attempts to read this variable must return
            different values.

            This variable will return the special value 0 if no new rows
            can be created.

            Note that the data type and the range of this object must be
            consistent with the definition of smRunIndex."
       ::= { smLaunchEntry 14 }

   smLaunchStorageType OBJECT-TYPE
       SYNTAX      StorageType
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "This object defines if this row is kept in volatile storage
            and lost upon reboot or if this row is backed up by stable
            storage.

            The value of smLaunchStorageType is only meaningful if the
            value of the corresponding RowStatus object is active.

            If smLaunchStorageType has the value permanent(4), then all
            objects whose MAX-ACCESS value is read-create must be
            writable, with the exception of the smLaunchStorageType and
            smLaunchRowStatus objects, which shall be read-only."
       DEFVAL { volatile }
       ::= { smLaunchEntry 15 }

   smLaunchRowStatus OBJECT-TYPE
       SYNTAX      RowStatus
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "A control that allows entries to be added and removed from
            this table.

            Attempts to `destroy' a row or to set a row `notInService'
            while the smLaunchOperStatus is `enabled' will result in
            an inconsistentValue error.




Levi & Schoenwaelder        Standards Track                    [Page 34]
^L
RFC 3165                       Script MIB                    August 2001


            Attempts to `destroy' a row or to set a row `notInService'
            where the value of the smLaunchStorageType object is
            `permanent' or `readOnly' will result in an
            inconsistentValue error.

            The value of this object has no effect on whether other
            objects in this conceptual row can be modified."
       ::= { smLaunchEntry 16 }

   smLaunchError OBJECT-TYPE
       SYNTAX      SnmpAdminString
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "This object contains a descriptive error message if an
            attempt to launch a script fails. Implementations must reset
            the error message to a zero-length string when a new attempt
            to launch a script is started."
       DEFVAL { ''H }
       ::= { smLaunchEntry 17 }

   smLaunchLastChange OBJECT-TYPE
       SYNTAX      DateAndTime
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The date and time when this launch table entry was last
            modified. The value '0000000000000000'H is returned if
            the launch table entry has not yet been modified.

            Note that a change of smLaunchStart, smLaunchControl,
            smLaunchRunIndexNext, smLaunchRowExpireTime, or the
            resetting of smLaunchError is not considered a change
            of this launch table entry."
       DEFVAL { '0000000000000000'H }
       ::= { smLaunchEntry 18 }

   smLaunchRowExpireTime OBJECT-TYPE
       SYNTAX      TimeInterval
       UNITS       "centi-seconds"
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The value of this object specifies how long this row remains
            in the `enabled' or `disabled' operational state. The value
            reported by this object ticks backwards. When the value
            reaches 0, it stops ticking backward and the row is
            deleted if there are no smRunTable entries associated with



Levi & Schoenwaelder        Standards Track                    [Page 35]
^L
RFC 3165                       Script MIB                    August 2001


            this smLaunchTable entry. Otherwise, the smLaunchOperStatus
            changes to `expired' and the row deletion is deferred
            until there are no smRunTable entries associated with this
            smLaunchTable entry.

            The smLaunchRowExpireTime will not tick backwards if it is
            set to its maximum value (2147483647). In other words,
            setting this object to its maximum value turns the timer
            off.

            The value of this object may be set in order to increase
            or reduce the remaining time that the launch table entry
            may be used. Setting the value to 0 will cause an immediate
            row deletion or transition into the `expired' operational
            state.

            It is not possible to set this object while the operational
            status is `expired'. Attempts to modify this object while
            the operational status is `expired' leads to an
            inconsistentValue error.

            Note that the timer ticks backwards independent of the
            operational state of the launch table entry."
       DEFVAL { 2147483647 }
       ::= { smLaunchEntry 19 }


   smRunTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF SmRunEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "This table lists and describes scripts that are currently
            running or have been running in the past."
       ::= { smRunObjects 2 }

   smRunEntry OBJECT-TYPE
       SYNTAX      SmRunEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "An entry describing a particular running or finished
            script."
       INDEX { smLaunchOwner, smLaunchName, smRunIndex }
       ::= { smRunTable 1 }

   SmRunEntry ::= SEQUENCE {
       smRunIndex          Integer32,



Levi & Schoenwaelder        Standards Track                    [Page 36]
^L
RFC 3165                       Script MIB                    August 2001


       smRunArgument       OCTET STRING,
       smRunStartTime      DateAndTime,
       smRunEndTime        DateAndTime,
       smRunLifeTime       TimeInterval,
       smRunExpireTime     TimeInterval,
       smRunExitCode       INTEGER,
       smRunResult         OCTET STRING,
       smRunControl        INTEGER,
       smRunState          INTEGER,
       smRunError          SnmpAdminString,
       smRunResultTime     DateAndTime,
       smRunErrorTime      DateAndTime
   }

   smRunIndex OBJECT-TYPE
       SYNTAX      Integer32 (1..2147483647)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The locally arbitrary, but unique identifier associated
            with this running or finished script. This value must be
            unique for all rows in the smRunTable with the same
            smLaunchOwner and smLaunchName.

            Note that the data type and the range of this object must
            be consistent with the definition of smLaunchRunIndexNext
            and smLaunchStart."
       ::= { smRunEntry 1 }

   smRunArgument OBJECT-TYPE
       SYNTAX      OCTET STRING
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The argument supplied to the script when it started."
       DEFVAL { ''H }
       ::= { smRunEntry 2 }

   smRunStartTime OBJECT-TYPE
       SYNTAX      DateAndTime
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The date and time when the execution started. The value
            '0000000000000000'H is returned if the script has not
            started yet."
       DEFVAL { '0000000000000000'H }
       ::= { smRunEntry 3 }



Levi & Schoenwaelder        Standards Track                    [Page 37]
^L
RFC 3165                       Script MIB                    August 2001


   smRunEndTime OBJECT-TYPE
       SYNTAX      DateAndTime
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The date and time when the execution terminated. The value
            '0000000000000000'H is returned if the script has not
            terminated yet."
       DEFVAL { '0000000000000000'H }
       ::= { smRunEntry 4 }

   smRunLifeTime OBJECT-TYPE
       SYNTAX      TimeInterval
       UNITS       "centi-seconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "This object specifies how long the script can execute.
            This object returns the remaining time that the script
            may run. The object is initialized with the value of the
            associated smLaunchLifeTime object and ticks backwards.
            The script is aborted immediately when the value reaches 0.

            The value of this object may be set in order to increase or
            reduce the remaining time that the script may run. Setting
            this value to 0 will abort script execution immediately,
            and, if the value of smRunExpireTime is also 0, will remove
            this entry from the smRunTable once it has terminated.

            If smRunLifeTime is set to its maximum value (2147483647),
            either by a set operation or by its initialization from the
            smLaunchLifeTime object, then it will not tick backwards.
            A running script with a maximum smRunLifeTime value will
            thus never be terminated with a `lifeTimeExceeded' exit
            code.

            The value of smRunLifeTime reflects the real-time execution
            time as seen by the outside world. The value of this object
            will always be 0 for a script that finished execution, that
            is smRunState has the value `terminated'.

            The value of smRunLifeTime does not change while a script
            is suspended, that is smRunState has the value `suspended'.
            Note that this does not affect set operations. It is legal
            to modify smRunLifeTime via set operations while a script
            is suspended."
       ::= { smRunEntry 5 }




Levi & Schoenwaelder        Standards Track                    [Page 38]
^L
RFC 3165                       Script MIB                    August 2001


   smRunExpireTime OBJECT-TYPE
       SYNTAX      TimeInterval
       UNITS       "centi-seconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "The value of this object specifies how long this row can
            exist in the smRunTable after the script has terminated.
            This object returns the remaining time that the row may
            exist before it is aged out. The object is initialized with
            the value of the associated smLaunchExpireTime object and
            ticks backwards. The entry in the smRunTable is destroyed
            when the value reaches 0 and the smRunState has the value
            `terminated'.

            The value of this object may be set in order to increase or
            reduce the remaining time that the row may exist.  Setting
            the value to 0 will destroy this entry as soon as the
            smRunState has the value `terminated'."
       ::= { smRunEntry 6 }

   smRunExitCode OBJECT-TYPE
       SYNTAX      INTEGER {
                       noError(1),
                       halted(2),
                       lifeTimeExceeded(3),
                       noResourcesLeft(4),
                       languageError(5),
                       runtimeError(6),
                       invalidArgument(7),
                       securityViolation(8),
                       genericError(9)
                   }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The value of this object indicates the reason why a
            script finished execution. The smRunExitCode code may have
            one of the following values:

            - `noError', which indicates that the script completed
               successfully without errors;

            - `halted', which indicates that the script was halted
               by a request from an authorized manager;

            - `lifeTimeExceeded', which indicates that the script
               exited because a time limit was exceeded;



Levi & Schoenwaelder        Standards Track                    [Page 39]
^L
RFC 3165                       Script MIB                    August 2001


            - `noResourcesLeft', which indicates that the script
               exited because it ran out of resources (e.g. memory);

            - `languageError', which indicates that the script exited
               because of a language error (e.g. a syntax error in an
               interpreted language);

            - `runtimeError', which indicates that the script exited
               due to a runtime error (e.g. a division by zero);

            - `invalidArgument', which indicates that the script could
               not be run because of invalid script arguments;

            - `securityViolation', which indicates that the script
               exited due to a security violation;

            - `genericError', which indicates that the script exited
               for an unspecified reason.

            If the script has not yet begun running, or is currently
            running, the value will be `noError'."
       DEFVAL { noError }
       ::= { smRunEntry 7 }

   smRunResult OBJECT-TYPE
       SYNTAX      OCTET STRING
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The result value produced by the running script. Note that
            the result may change while the script is executing."
       DEFVAL { ''H }
       ::= { smRunEntry 8 }

   smRunControl OBJECT-TYPE
       SYNTAX      INTEGER {
                       abort(1),
                       suspend(2),
                       resume(3),
                       nop(4)
                   }
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "The value of this object indicates the desired status of the
            script execution defined by this row.

            Setting this object to `abort' will abort execution if the



Levi & Schoenwaelder        Standards Track                    [Page 40]
^L
RFC 3165                       Script MIB                    August 2001


            value of smRunState is `initializing', `executing',
            `suspending', `suspended' or `resuming'. Setting this object
            to `abort' when the value of smRunState is `aborting' or
            `terminated', or if the implementation can determine that
            the attempt to abort the execution would fail, will result
            in an inconsistentValue error.

            Setting this object to `suspend' will suspend execution
            if the value of smRunState is `executing'. Setting this
            object to `suspend' will cause an inconsistentValue error
            if the value of smRunState is not `executing' or if the
            implementation can determine that the attempt to suspend
            the execution would fail.

            Setting this object to `resume' will resume execution
            if the value of smRunState is `suspending' or
            `suspended'. Setting this object to `resume' will cause an
            inconsistentValue error if the value of smRunState is
            not `suspended' or if the implementation can determine
            that the attempt to resume the execution would fail.

            Setting this object to nop(4) has no effect."
       DEFVAL { nop }
       ::= { smRunEntry 9 }

   smRunState OBJECT-TYPE
       SYNTAX      INTEGER {
                       initializing(1),
                       executing(2),
                       suspending(3),
                       suspended(4),
                       resuming(5),
                       aborting(6),
                       terminated(7)
                   }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The value of this object indicates the script's execution
            state. If the script has been invoked but has not yet
            begun execution, the value will be `initializing'. If the
            script is running, the value will be `executing'.

            A running script which received a request to suspend
            execution first transitions into a temporary `suspending'
            state.  The temporary `suspending' state changes to
            `suspended' when the script has actually been suspended. The
            temporary `suspending' state changes back to `executing' if



Levi & Schoenwaelder        Standards Track                    [Page 41]
^L
RFC 3165                       Script MIB                    August 2001


            the attempt to suspend the running script fails.

            A suspended script which received a request to resume
            execution first transitions into a temporary `resuming'
            state. The temporary `resuming' state changes to `running'
            when the script has actually been resumed. The temporary
            `resuming' state changes back to `suspended' if the attempt
            to resume the suspended script fails.

            A script which received a request to abort execution but
            which is still running first transitions into a temporary
            `aborting' state.

            A script which has finished its execution is `terminated'."
       ::= { smRunEntry 10 }

   smRunError OBJECT-TYPE
       SYNTAX      SnmpAdminString
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "This object contains a descriptive error message if the
            script startup or execution raised an abnormal condition.
            An implementation must store a descriptive error message
            in this object if the script exits with the smRunExitCode
            `genericError'."
       DEFVAL { ''H }
       ::= { smRunEntry 11 }

   smRunResultTime OBJECT-TYPE
       SYNTAX      DateAndTime
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The date and time when the smRunResult was last updated.
            The value '0000000000000000'H is returned if smRunResult
            has not yet been updated after the creation of this
            smRunTable entry."
       DEFVAL { '0000000000000000'H }
       ::= { smRunEntry 12 }

   smRunErrorTime OBJECT-TYPE
       SYNTAX      DateAndTime
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The date and time when the smRunError was last updated.
            The value '0000000000000000'H is returned if smRunError



Levi & Schoenwaelder        Standards Track                    [Page 42]
^L
RFC 3165                       Script MIB                    August 2001


            has not yet been updated after the creation of this
            smRunTable entry."
       DEFVAL { '0000000000000000'H }
       ::= { smRunEntry 13 }

   --
   -- Notifications. The definition of smTraps makes notification
   -- registrations reversible (see STD 58, RFC 2578).
   --

   smTraps OBJECT IDENTIFIER ::= { smNotifications 0 }

   smScriptAbort NOTIFICATION-TYPE
       OBJECTS     { smRunExitCode, smRunEndTime, smRunError }
       STATUS      current
       DESCRIPTION
           "This notification is generated whenever a running script
            terminates with an smRunExitCode unequal to `noError'."
       ::= { smTraps 1 }

   smScriptResult NOTIFICATION-TYPE
       OBJECTS     { smRunResult }
       STATUS      current
       DESCRIPTION
           "This notification can be used by scripts to notify other
            management applications about results produced by the
            script.

            This notification is not automatically generated by the
            Script MIB implementation. It is the responsibility of
            the executing script to emit this notification where it
            is appropriate to do so."
       ::= { smTraps 2 }

   smScriptException NOTIFICATION-TYPE
       OBJECTS     { smRunError }
       STATUS      current
       DESCRIPTION
           "This notification can be used by scripts to notify other
            management applications about script errors.

            This notification is not automatically generated by the
            Script MIB implementation. It is the responsibility of
            the executing script or the runtime system to emit this
            notification where it is appropriate to do so."
       ::= { smTraps 3 }

   -- conformance information



Levi & Schoenwaelder        Standards Track                    [Page 43]
^L
RFC 3165                       Script MIB                    August 2001


   smCompliances OBJECT IDENTIFIER ::= { smConformance 1 }
   smGroups      OBJECT IDENTIFIER ::= { smConformance 2 }

   -- compliance statements

   smCompliance2 MODULE-COMPLIANCE
       STATUS      current
       DESCRIPTION
           "The compliance statement for SNMP entities which implement
            the Script MIB."
       MODULE      -- this module
       MANDATORY-GROUPS {
               smLanguageGroup, smScriptGroup2, smLaunchGroup2,
               smRunGroup2, smNotificationsGroup2
       }
       GROUP   smCodeGroup
       DESCRIPTION
           "The smCodeGroup is mandatory only for those implementations
            that support the downloading of scripts via SNMP."
       OBJECT  smScriptSource
       MIN-ACCESS  read-only
       DESCRIPTION
           "The smScriptSource object is read-only for implementations
            that are not able to download script code from a URL."
       OBJECT smCodeText
       DESCRIPTION
           "A compliant implementation need only support write access to
            the smCodeText object only during row creation."
       OBJECT smLaunchArgument
       DESCRIPTION
           "A compliant implementation has to support a minimum size
            for smLaunchArgument of 255 octets."
       OBJECT smRunArgument
       DESCRIPTION
           "A compliant implementation has to support a minimum size
            for smRunArgument of 255 octets."
       OBJECT smRunResult
       DESCRIPTION
           "A compliant implementation has to support a minimum size
            for smRunResult of 255 octets."
       OBJECT smRunState
       DESCRIPTION
           "A compliant implementation does not have to support script
            suspension and the smRunState `suspended'. Such an
            implementation will change into the `suspending' state
            when the smRunControl is set to `suspend' and remain in this
            state until smRunControl is set to `resume' or the script
            terminates."



Levi & Schoenwaelder        Standards Track                    [Page 44]
^L
RFC 3165                       Script MIB                    August 2001


       ::= { smCompliances 2 }

   smLanguageGroup OBJECT-GROUP
       OBJECTS {
           smLangLanguage, smLangVersion,
           smLangVendor, smLangRevision,
           smLangDescr, smExtsnExtension,
           smExtsnVersion, smExtsnVendor,
           smExtsnRevision, smExtsnDescr
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing information about the
            capabilities of the scripting engine."
       ::= { smGroups 1 }

   smScriptGroup2 OBJECT-GROUP
       OBJECTS {
           smScriptDescr, smScriptLanguage,
           smScriptSource, smScriptAdminStatus,
           smScriptOperStatus, smScriptStorageType,
           smScriptRowStatus, smScriptError,
           smScriptLastChange
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing information about
            installed scripts."
       ::= { smGroups 7 }

   smCodeGroup OBJECT-GROUP
       OBJECTS {
           smCodeText, smCodeRowStatus
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects used to download or modify scripts
            by using SNMP set requests."
       ::= { smGroups 3 }

   smLaunchGroup2 OBJECT-GROUP
       OBJECTS {
           smLaunchScriptOwner, smLaunchScriptName,
           smLaunchArgument, smLaunchMaxRunning,
           smLaunchMaxCompleted, smLaunchLifeTime,
           smLaunchExpireTime, smLaunchStart,
           smLaunchControl, smLaunchAdminStatus,
           smLaunchOperStatus, smLaunchRunIndexNext,



Levi & Schoenwaelder        Standards Track                    [Page 45]
^L
RFC 3165                       Script MIB                    August 2001


           smLaunchStorageType, smLaunchRowStatus,
           smLaunchError, smLaunchLastChange,
           smLaunchRowExpireTime
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing information about scripts
            that can be launched."
       ::= { smGroups 8 }

   smRunGroup2 OBJECT-GROUP
       OBJECTS {
           smRunArgument, smRunStartTime,
           smRunEndTime, smRunLifeTime,
           smRunExpireTime, smRunExitCode,
           smRunResult, smRunState,
           smRunControl, smRunError,
           smRunResultTime, smRunErrorTime
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing information about running
            scripts."
       ::= { smGroups 9 }

   smNotificationsGroup2 NOTIFICATION-GROUP
       NOTIFICATIONS {
           smScriptAbort,
           smScriptResult,
           smScriptException
       }
       STATUS      current
       DESCRIPTION
           "The notifications emitted by the Script MIB."
       ::= { smGroups 10 }

   --
   -- Deprecated compliance and conformance group definitions
   -- from RFC 2592.
   --

   smCompliance MODULE-COMPLIANCE
       STATUS      deprecated
       DESCRIPTION
           "The compliance statement for SNMP entities which implement
            the Script MIB."
       MODULE      -- this module
       MANDATORY-GROUPS {



Levi & Schoenwaelder        Standards Track                    [Page 46]
^L
RFC 3165                       Script MIB                    August 2001


               smLanguageGroup, smScriptGroup, smLaunchGroup, smRunGroup
       }
       GROUP   smCodeGroup
       DESCRIPTION
           "The smCodeGroup is mandatory only for those implementations
            that support the downloading of scripts via SNMP."
       OBJECT  smScriptSource
       MIN-ACCESS  read-only
       DESCRIPTION
           "The smScriptSource object is read-only for implementations
            that are not able to download script code from a URL."
       OBJECT smCodeText
       DESCRIPTION
           "A compliant implementation need only support write access
            to the smCodeText object during row creation."
       OBJECT smLaunchArgument
       DESCRIPTION
           "A compliant implementation has to support a minimum size
            for smLaunchArgument of 255 octets."
       OBJECT smRunArgument
       DESCRIPTION
           "A compliant implementation has to support a minimum size
            for smRunArgument of 255 octets."
       OBJECT smRunResult
       DESCRIPTION
           "A compliant implementation has to support a minimum size
            for smRunResult of 255 octets."
       OBJECT smRunState
       DESCRIPTION
           "A compliant implementation does not have to support script
            suspension and the smRunState `suspended'. Such an
            implementation will change into the `suspending' state
            when the smRunControl is set to `suspend' and remain in this
            state until smRunControl is set to `resume' or the script
            terminates."
       ::= { smCompliances 1 }

   smScriptGroup OBJECT-GROUP
       OBJECTS {
           smScriptDescr, smScriptLanguage,
           smScriptSource, smScriptAdminStatus,
           smScriptOperStatus, smScriptStorageType,
           smScriptRowStatus
       }
       STATUS      deprecated
       DESCRIPTION
           "A collection of objects providing information about
            installed scripts."



Levi & Schoenwaelder        Standards Track                    [Page 47]
^L
RFC 3165                       Script MIB                    August 2001


       ::= { smGroups 2 }

   smLaunchGroup OBJECT-GROUP
       OBJECTS {
           smLaunchScriptOwner, smLaunchScriptName,
           smLaunchArgument, smLaunchMaxRunning,
           smLaunchMaxCompleted, smLaunchLifeTime,
           smLaunchExpireTime, smLaunchStart,
           smLaunchControl, smLaunchAdminStatus,
           smLaunchOperStatus, smLaunchRunIndexNext,
           smLaunchStorageType, smLaunchRowStatus
       }
       STATUS      deprecated
       DESCRIPTION
           "A collection of objects providing information about scripts
            that can be launched."
       ::= { smGroups 4 }

   smRunGroup OBJECT-GROUP
       OBJECTS {
           smRunArgument, smRunStartTime,
           smRunEndTime, smRunLifeTime,
           smRunExpireTime, smRunExitCode,
           smRunResult, smRunState,
           smRunControl, smRunError
       }
       STATUS      deprecated
       DESCRIPTION
           "A collection of objects providing information about running
            scripts."
       ::= { smGroups 5 }

   smNotificationsGroup NOTIFICATION-GROUP
       NOTIFICATIONS {
           smScriptAbort,
           smScriptResult
       }
       STATUS      deprecated
       DESCRIPTION
           "The notifications emitted by the Script MIB."
       ::= { smGroups 6 }

   END








Levi & Schoenwaelder        Standards Track                    [Page 48]
^L
RFC 3165                       Script MIB                    August 2001


7.  Usage Examples

   This section presents some examples that explain how a manager can
   use the Script MIB defined in this memo.  The purpose of these
   examples is to explain the steps that are normally used to delegate
   management scripts.

7.1.  Pushing a Script via SNMP

   This example explains the steps performed by a manager to push a
   script into a distributed manager.

   1. The manager first checks the smLangTable and the smExtsnTable in
      order to select the appropriate script or language.

   2. The manager creates a row in the smScriptTable by issuing an SNMP
      set-request.  The smScriptRowStatus object is set to
      `createAndWait' and the smScriptSource object is set to an empty
      string.  The smScriptLanguage object is set to the language in
      which the script was written.  The smScriptStorageType object is
      set to `volatile' to indicate that the script will be loaded via
      the smCodeTable.  The smScriptOwner is set to a string which
      identifies the principal who owns the new row.  The smScriptName
      defines the administratively assigned unique name for the script.

   3. The manager sets the smScriptRowStatus object to `active' and the
      smScriptAdminStatus object to `editing'.

   4. The manager pushes the script to the distributed manager by
      issuing a couple of SNMP set-requests to fill the smCodeTable.

   5. Once the whole script has been transferred, the manager sends a
      set-request to set the smScriptAdminStatus object to `enabled'.
      The Script MIB implementation now makes the script accessible to
      the runtime system.  This might include the compilation of the
      script if the language requires a compilation step.

   6. The manager polls the smScriptOperStatus object until the value is
      either `enabled' or one of the error status codes.  The script can
      only be used if the value of smScriptOperStatus is `enabled'.

   7. If the manager wants to store the script in local non-volatile
      storage, it should send a set-request which changes the
      smScriptStorageType object to `nonVolatile'.







Levi & Schoenwaelder        Standards Track                    [Page 49]
^L
RFC 3165                       Script MIB                    August 2001


7.2.  Pulling a Script from a URL

   This example explains the steps performed by a manager to cause a
   distributed manager to pull a script from a URL.

   1. The manager first checks the smLangTable and the smExtsnTable in
      order to select the appropriate script or language.

   2. The manager creates a row in the smScriptTable by issuing an SNMP
      set-request.  The smScriptRowStatus object is set to
      `createAndWait' and the smScriptSource object is set to the URL
      which points to the script source.  The smScriptLanguage object is
      set to the language in which the script was written.  The
      smScriptOwner is set to a string which identifies the principal
      who owns the new row.  The smScriptName defines the
      administratively assigned unique name for the script.

   3. The manager sets the smScriptRowStatus object to `active'.

   4. The manager sends a set-request to set the smScriptAdminStatus
      object to `enabled'.  The Script MIB implementation now makes the
      script accessible to the runtime system.  This causes a retrieval
      operation to pull the script from the URL stored in
      smScriptSource.  This retrieval operation might be followed by a
      compile operation if the language requires a compilation step.

   5. The manager polls the smScriptOperStatus object until the value is
      either `enabled' or one of the error status codes.  The script can
      only be used if the value of smScriptOperStatus is `enabled'.

   6. If the manager wants to store the script in local non-volatile
      storage, it should send a set-request which changes the
      smScriptStorageType object to `nonVolatile'.

7.3.  Modifying an Existing Script

   This section explains how a manager can modify a script by sending
   SNMP set-requests.

   1. First, the script is de-activated by setting the
      smScriptAdminStatus to `disabled'.

   2. The manager polls the smScriptOperStatus object until the value is
      `disabled'.

   3. The manager sets smScriptSource to an empty string and
      smScriptAdminStatus to `editing'.  This makes the script source
      available in the smCodeTable.



Levi & Schoenwaelder        Standards Track                    [Page 50]
^L
RFC 3165                       Script MIB                    August 2001


   4. The manager polls the smScriptOperStatus object until the value is
      `editing'.

   5. The manager sends SNMP set-requests to modify the script in the
      smCodeTable.

   6. The manager sends a set-request to set the smScriptAdminStatus
      object to `enabled'.  The Script MIB implementation now makes the
      script accessible to the runtime system.  This might include the
      compilation of the script if the language requires a compilation
      step.

   7. The manager polls the smScriptOperStatus object until the value is
      either `enabled' or one of the error status codes.  The script can
      only be used if the value of smScriptOperStatus is `enabled'.

7.4.  Removing an Existing Script

   This section explains how a manager can remove a script from a
   distributed manager.

   1. First, the manager sets the smScriptAdminStatus to `disabled'.
      This will ensure that no new scripts can be started while running
      scripts finish their execution.

   2. The manager polls the smScriptOperStatus object until the value is
      `disabled'.

   3. The manager sends an SNMP set-request to change the
      smScriptRowStatus object to `destroy'.  This will remove the row
      and all associated resources from the Script MIB implementation.

7.5.  Creating a Launch Button

   This section explains how a manager can create a launch button for
   starting a script.

   1. The manager, who is identified by an smLaunchOwner value, first
      chooses a name for the new row in the smLaunchTable.  The manager
      sends an SNMP set-request to set the smLaunchRowStatus object for
      this smLaunchOwner and smLaunchName to `createAndWait'.

   2. The manager fills the new smLaunchTable row with all required
      parameters.  The smLaunchScriptOwner and smLaunchScriptName values
      point to the script that should be started from this launch
      button.

   3. The manager sets the smLaunchRowStatus object to `active'.



Levi & Schoenwaelder        Standards Track                    [Page 51]
^L
RFC 3165                       Script MIB                    August 2001


   4. The manager sends a set-request to change smLaunchAdminStatus to
      `enabled' once the new smLaunchTable row is complete.

   5. The manager polls the smLaunchOperStatus object until the value is
      `enabled'.

7.6.  Launching a Script

   This section explains the suggested way to launch a script from a
   given launch button.

   1. The manager first retrieves the value of smLaunchRunIndexNext from
      the launch button selected to start the script.

   2. The manager sends an SNMP set-request to set the smLaunchStart
      object to the value obtained in step 1.  This will launch the
      script if all necessary pre-conditions are satisfied (see the
      definition of smLaunchStart for more details).  The manager can
      also provide the smLaunchArgument in the same set-request that is
      used to start the script.  Upon successful start, a new row will
      be created in the smRunTable indexed by smLaunchOwner,
      smLaunchName and the value written to smLaunchStart.

   3. The manager polls the smRunState object until the value is either
      `executing' (the default case), `suspended' or `terminated'.

   The first step is not required.  A manager can also try to guess an
   unused value for smRunIndex if the manager wants to start the script
   in a single transaction.  A manager can also use the special value 0
   if it does not care about the smRunIndex.

7.7.  Suspending a Running Script

   This section explains how a manager can suspend a running script.

   1. The manager sets the smRunControl object of the running script or
      the smLaunchControl object of the launch button used to start the
      running script to `suspend'.  Setting smLaunchControl will suspend
      all running scripts started from the launch button while
      smRunControl will only suspend the running script associated with
      the smRunControl instance.

   2. The manager polls the smRunState object until the value is either
      `suspended', `executing', or `terminated'.  If the value is
      `suspended', then the suspend operation was successful.  If the
      value is `executing', then the attempt to suspend the script





Levi & Schoenwaelder        Standards Track                    [Page 52]
^L
RFC 3165                       Script MIB                    August 2001


      failed.  The value `terminated' can be received in cases where the
      suspend operation failed and the running script terminated between
      the polls.

   Note that the set operation in the first step can lead to an
   inconsistentValue error which indicates that the suspend operation
   failed (e.g., because the runtime system does not support
   suspend/resume).  There is no need to poll smRunState in this case.

7.8.  Resuming a Suspended Script

   This section explains how a manager can resume a suspended script.

   1. The manager sets the smRunControl object of the running script or
      the smLaunchControl object of the launch button used to start the
      running script to `resume'.  Setting smLaunchControl will resume
      all running scripts started from the launch button while
      smRunControl will only resume the running script associated with
      the smRunControl instance.

   2. The manager polls the smRunState object until the value is either
      `suspended', `executing', or `terminated'.  If the value is
      `executing', then the resume operation was successful.  If the
      value is `suspended', then the attempt to resume the script
      failed.  The value `terminated' can be received in cases where the
      resume operation was successful and the running script terminated
      between the polls.

   Note that the set operation in the first step can lead to an
   inconsistentValue error which indicates that the resume operation
   failed (e.g., because the runtime system does not support
   suspend/resume).  There is no need to poll smRunState in this case.

7.9.  Terminating a Running Script

   This section explains two ways to terminate a running script.  The
   first approach is as follows:

   1. The manager sets the smRunControl object of the running script or
      the smLaunchControl object of the launch button used to start the
      running script to `abort'.  Setting smLaunchControl will abort all
      running scripts started from the launch button while smRunControl
      will only abort the running script associated with the
      smRunControl instance.

   2. The manager polls the smRunState object until the value is
      `terminated'.




Levi & Schoenwaelder        Standards Track                    [Page 53]
^L
RFC 3165                       Script MIB                    August 2001


   The second way to terminate a script is to set the smRunLifeTime to
   zero which causes the runtime system to terminate the script with a
   `lifeTimeExceeded' exit code:

   1. The manager changes the value of smRunLifeTime to 0.  This causes
      the Script MIB implementation to abort the script because the
      remaining life time has expired.

   2. The manager polls the smRunState object until the value is
      `terminated'.

   Note that changing the smRunLifeTime value can also be used to
   increase the permitted lifetime of a running script.  For example, a
   manager can choose to set smRunLifeTime to a small fixed time
   interval and increase the value periodically.  This strategy has the
   nice effect that scripts terminate automatically if the manager loses
   contact with the Script MIB engine.

7.10.  Removing a Terminated Script

   This section explains how a manager can remove a terminated script.

   1. The manager changes the smRunExpireTime to 0.  This causes the
      Script MIB implementation to destroy the smRunTable entry of the
      terminated script.

7.11.  Removing a Launch Button

   This section explains how a manager can remove a launch button from a
   distributed manager.

   1. First, the manager sets the smLaunchAdminStatus to `disabled'.
      This will ensure that no new scripts can be started from this
      launch button while running scripts finish their execution.

   2. The manager polls the smLaunchOperStatus object until the value is
      `disabled'.

   3. The manager sends an SNMP set-request to change the
      smLaunchRowStatus object to `destroy'.  This will remove the row
      and all associated resources from the Script MIB implementation.

8.  VACM Configuration Examples

   This section shows how the view-based access control model defined in
   RFC 2575 [RFC2575] can be configured to control access to the Script
   MIB.




Levi & Schoenwaelder        Standards Track                    [Page 54]
^L
RFC 3165                       Script MIB                    August 2001


8.1.  Sandbox for Guests

   The first example demonstrates how to configure VACM to give the
   members of the VACM group "guest" limited access to the Script MIB.
   The MIB views defined below give the members of the "guest" group a
   sandbox where they can install and start their own scripts, but not
   access any other scripts maintained by the Script MIB implementation.

      vacmAccessReadView."guest"."".usm.authNoPriv = "guestReadView"
      vacmAccessWriteView."guest"."".usm.authNoPriv = "guestWriteView"

   The guestReadView grants read access to the smLangTable, the
   smExtsnTable and to all the table entries owned by "guest":

      guestReadView:
          smLangTable                       (included)
          smExtsnTable                      (included)
          smScriptObjects.*.*.*."guest"     (included)
          smRunObjects.*.*.*."guest"        (included)

   The guestWriteView grants write access to all the table entries owned
   by "guest":

      guestWriteView:
          smScriptObjects.*.*.*."guest"     (included)
          smRunObjects.*.*.*."guest"        (included)

8.2.  Sharing Scripts

   This example demonstrates how VACM can be used to share a repository
   of scripts between the members of the "senior" and the members of the
   "junior" VACM group:

      vacmAccessReadView."junior"."".usm.authNoPriv = "juniorReadView"
      vacmAccessWriteView."junior"."".usm.authNoPriv = "juniorWriteView"

      juniorReadView:
          smLangTable                       (included)
          smExtsnTable                      (included)
          smScriptObjects.*.*.*."junior"    (included)
          smRunObjects.*.*.*."junior"       (included)
          smScriptObjects.*.*.*."utils"     (included)

      juniorWriteView:
          smScriptObjects.*.*.*."junior"    (included)
          smRunObjects.*.*.*."junior"       (included)





Levi & Schoenwaelder        Standards Track                    [Page 55]
^L
RFC 3165                       Script MIB                    August 2001


   The definitions above allow the members of the "junior" VACM group to
   start the scripts owned by "utils" in addition to the script the
   members of the "junior" VACM group installed themselves.  This is
   accomplished by giving the members of "junior" read access to scripts
   in "utils".  This allows members of "junior" to create entries in the
   smLaunchTable which refer to scripts in "utils", and to launch those
   scripts using these entries in the smLaunchTable.

      vacmAccessReadView."senior"."".usm.authNoPriv = "seniorReadView"
      vacmAccessWriteView."senior"."".usm.authNoPriv = "seniorWriteView"

      seniorReadView:
          smLangTable                       (included)
          smExtsnTable                      (included)
          smScriptObjects.*.*.*."senior"    (included)
          smRunObjects.*.*.*."senior"       (included)
          smScriptObjects.*.*.*."utils"     (included)

      seniorWriteView:
          smScriptObjects.*.*.*."senior"    (included)
          smRunObjects.*.*.*."senior"       (included)
          smScriptObjects.*.*.*."utils"     (included)

   The definitions for the members of the "senior" VACM group allow to
   start the scripts owned by "utils" in addition to the script the
   members of the "senior" VACM group installed themself.  The third
   write access rule in the seniorWriteView also grants the permission
   to install scripts owned by "utils".  The members of the "senior"
   VACM group therefore have the permissions to install and modify
   scripts that can be called by the members of the "junior" VACM group.

8.3.  Emergency Scripts

   This example demonstrates how VACM can be used to allow the members
   of the "junior" VACM group to launch scripts that are executed with
   the permissions associated with the "emergency" owner.  This works by
   adding the following rules to the juniorReadView and the
   juniorWriteView:

      juniorReadView:
          smScriptObjects.*.*.*."emergency" (included)
          smRunObjects.*.*.*."emergency"    (included)

      juniorWriteView
          smLaunchStart."emergency"         (included)
          smLaunchArgument."emergency"      (included)





Levi & Schoenwaelder        Standards Track                    [Page 56]
^L
RFC 3165                       Script MIB                    August 2001


   The rules added to the juniorReadView grant read access to the
   scripts, the launch buttons and the results owned by "emergency".
   The rules added to the juniorWriteView grant write permissions to the
   smLaunchStart and smLaunchArgument variables owned by "emergency".
   Members of the "junior" VACM group can therefore start scripts that
   will execute under the owner "emergency".

      seniorReadView:
          smScriptObjects.*.*.*."emergency" (included)
          smRunObjects.*.*.*."emergency"    (included)

      seniorWriteView:
          smScriptObjects.*.*.*."emergency" (included)
          smRunObjects.*.*.*."emergency"    (included)

   The rules added to the seniorReadView and the seniorWriteView will
   give the members of the "senior" VACM group the rights to install
   emergency scripts and to configure appropriate launch buttons.

9.  IANA Considerations

   The Internet Assigned Numbers Authority (IANA) is responsible for
   maintaining a MIB module (IANA-LANGUAGE-MIB) which provides OID
   registrations for well-known languages.  The IANA language registry
   is intended to reduce interoperability problems by providing a single
   list of well-known languages.  However, it is of course still
   possible to register languages in private OID spaces.  Registering
   languages in private OID spaces is especially attractive if a
   language is used for experimentation or if a language is only used in
   environments where the distribution of MIB modules with the language
   registration does not cause any maintenance problems.

   Any additions or changes to the list of languages registered via IANA
   require Designated Expert Review as defined in the IANA guidelines
   [RFC2434].  The Designated Expert will be selected by the IESG Area
   Director for the IETF Operations and Management Area.

10.  Security Considerations

   There are a number of management objects defined in this MIB that
   have a MAX-ACCESS clause of read-write and/or read-create.  Such
   objects may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.






Levi & Schoenwaelder        Standards Track                    [Page 57]
^L
RFC 3165                       Script MIB                    August 2001


   SNMPv1 by itself is not a secure environment.  Even if the network
   itself is secure (for example by using IPSec), even then, there is no
   control as to who on the secure network is allowed to access and
   GET/SET (read/change/create/delete) the objects in this MIB.

   It is recommended that the implementers consider the security
   features as provided by the SNMPv3 framework.  Specifically, the use
   of the User-based Security Model RFC 2574 [RFC2574] and the View-
   based Access Control Model RFC 2575 [RFC2575] is recommended.

   It is then a customer/user responsibility to ensure that the SNMP
   entity giving access to an instance of this MIB, is properly
   configured to give access to the objects only to those principals
   (users) that have legitimate rights to indeed GET or SET
   (change/create/delete) them.

   This MIB provides the ability to distribute applications written in
   an arbitrary language to remote systems in a network.  The security
   features of the languages available in a particular implementation
   should be taken into consideration when deploying an implementation
   of this MIB.

   To facilitate the provisioning of access control by a security
   administrator using the View-Based Access Control Model (VACM)
   defined in RFC 2575 [RFC2575] for tables in which multiple users may
   need to independently create or modify entries, the initial index is
   used as an "owner index".  Such an initial index has a syntax of
   SnmpAdminString, and can thus be trivially mapped to a securityName
   or groupName as defined in VACM, in accordance with a security
   policy.

   All entries in related tables belonging to a particular user will
   have the same value for this initial index.  For a given user's
   entries in a particular table, the object identifiers for the
   information in these entries will have the same subidentifiers
   (except for the "column" subidentifier) up to the end of the encoded
   owner index.  To configure VACM to permit access to this portion of
   the table, one would create vacmViewTreeFamilyTable entries with the
   value of vacmViewTreeFamilySubtree including the owner index portion,
   and vacmViewTreeFamilyMask "wildcarding" the column subidentifier.
   More elaborate configurations are possible.

   The VACM access control mechanism described above provides control
   over SNMP access to Script MIB objects.  There are a number of other
   access control issues that are outside of the scope of this MIB.  For
   example, access control on URLs, especially those that use the file
   scheme, must be realized by the underlying operating system.  A
   mapping of the owner index value to a local operating system security



Levi & Schoenwaelder        Standards Track                    [Page 58]
^L
RFC 3165                       Script MIB                    August 2001


   user identity should be used by an implementation of this MIB to
   control access to operating system resources when resolving URLs or
   executing scripts.

11.  Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights.  Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11.  Copies of
   claims of rights made available for publication and any assurances of
   licenses to be made available, or the result of an attempt made to
   obtain a general license or permission for the use of such
   proprietary rights by implementors or users of this specification can
   be obtained from the IETF Secretariat.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard.  Please address the information to the IETF Executive
   Director.

12.  Changes from RFC 2592

   The following list documents major changes from the previous version
   of this document, published as RFC 2592:

   -  Updated the boilerplate and the references.

   -  Added revision clauses to the module identity macro.

   -  Various typos have been fixed.

   -  Added SIZE restriction to smScriptName which is consistent with
      smLaunchScriptName.  Added DEFVAL and some clarifying text on the
      usage of a zero-length string to smLaunchScriptName.

   -  Clarified under which conditions changes to smScriptLanguage are
      invalid.

   -  Added new smScriptError and smLaunchError objects.

   -  Setting smRunLifeTime to its maximum value now disables the timer
      so that scripts can run forever.



Levi & Schoenwaelder        Standards Track                    [Page 59]
^L
RFC 3165                       Script MIB                    August 2001


   -  Added the `autostart' value to the smLaunchAdminStatus object
      which allows to launch scripts during the disable->enabled
      transition of smLaunchOperStatus.

   -  Added an additional step to the "creating a launch button"
      procedure which sets the smLaunchRowStatus to active.

   -  Added a final polling step in the procedure to launch a script.

   -  Added a final polling step in the procedure to terminate a running
      script.

   -  Removed the requirement that smRunError is a zero-length string
      while the smRunExitCode has the value `noError'.

   -  Added new smScriptLastChange, smLaunchLastChange, smRunResultTime,
      and smRunErrorTime objects.

   -  Added some additional boilerplate text to the security
      considerations section.

   -  Added a new smLaunchRowExpireTime object and a new `expired' state
      to the smLaunchOperStatus object.

   -  Clarified that the smRunState object reports the actual state if
      attempts to suspend or resume scripts fail.

   -  Clarified the conditions under which set operations to
      smLaunchControl and smRunControl can lead to inconsistentValue
      errors.

   -  Added procedures for suspending/resuming/removing running scripts
      to section 7.

   -  Added text to the smScriptStorageType description to better
      highlight the difference between the storage type of the script
      row entry and the script itself.

   -  Updated the smCompliances statement to not require write access to
      the smCodeText object after row creation.

   -  Deprecated smCompliance, smScriptGroup, smLaunchGroup, smRunGroup,
      smNotificationsGroup and created smCompliance2, smScriptGroup2,
      smLaunchGroup2, smRunGroup2 and smNotificationsGroup2 that take
      care of the new objects and notifications.






Levi & Schoenwaelder        Standards Track                    [Page 60]
^L
RFC 3165                       Script MIB                    August 2001


13.  Acknowledgments

   This document was produced by the IETF Distributed Management
   (DISMAN) working group.

14.  References

   [RFC2571]  Harrington, D., Presuhn, R. and B. Wijnen, "An
              Architecture for Describing SNMP Management Frameworks",
              RFC 2571, April 1999.

   [RFC1155]  Rose, M. and K. McCloghrie, "Structure and Identification
              of Management Information for TCP/IP-based Internets", STD
              16, RFC 1155, May 1990.

   [RFC1212]  Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD
              16, RFC 1212, March 1991.

   [RFC1215]  Rose, M., "A Convention for Defining Traps for use with
              the SNMP", RFC 1215, March 1991.

   [RFC2578]  McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
              Rose, M. and S. Waldbusser, "Structure of Management
              Information Version 2 (SMIv2)", STD 58, RFC 2578, April
              1999.

   [RFC2579]  McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
              Rose, M. and S. Waldbusser, "Textual Conventions for
              SMIv2", STD 58, RFC 2579, April 1999.

   [RFC2580]  McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
              Rose, M. and S. Waldbusser, "Conformance Statements for
              SMIv2", STD 58, RFC 2580, April 1999.

   [RFC1157]  Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple
              Network Management Protocol", STD 15, RFC 1157, May 1990.

   [RFC1901]  Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
              "Introduction to Community-based SNMPv2", RFC 1901,
              January 1996.

   [RFC1906]  Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
              "Transport Mappings for Version 2 of the Simple Network
              Management Protocol (SNMPv2)", RFC 1906, January 1996.

   [RFC2572]  Case, J., Harrington D., Presuhn R. and B. Wijnen,
              "Message Processing and Dispatching for the Simple Network
              Management Protocol (SNMP)", RFC 2572, April 1999.



Levi & Schoenwaelder        Standards Track                    [Page 61]
^L
RFC 3165                       Script MIB                    August 2001


   [RFC2574]  Blumenthal, U. and B. Wijnen, "User-based Security Model
              (USM) for version 3 of the Simple Network Management
              Protocol (SNMPv3)", RFC 2574, April 1999.

   [RFC1905]  Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
              "Protocol Operations for Version 2 of the Simple Network
              Management Protocol (SNMPv2)", RFC 1905, January 1996.

   [RFC2573]  Levi, D., Meyer, P. and B. Stewart, "SNMPv3 Applications",
              RFC 2573, April 1999.

   [RFC2575]  Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based
              Access Control Model (VACM) for the Simple Network
              Management Protocol (SNMP)", RFC 2575, April 1999.

   [RFC2570]  Case, J., Mundy, R., Partain, D. and B. Stewart,
              "Introduction to Version 3 of the Internet-standard
              Network Management Framework", RFC 2570, April 1999.

   [RFC2028]  Hovey, R. and S. Bradner, "The Organizations Involved in
              the IETF Standards Process", BCP 11, RFC 2028, October
              1996.

   [RFC2396]  Berners-Lee, T., Fielding, R. and L. Masinter, " Uniform
              Resource Identifiers (URI): Generic Syntax", RFC 2396,
              August 1998.

   [RFC959]   Postel, J. and J. Reynolds, "File Transfer Protocol", STD
              9, RFC 959, October 1985.

   [RFC2616]  Fielding, R., Gettys, J., Mogul, J., Frystyk, H.,
              Masinter, L., Leach, P. and T. Berners-Lee, "Hypertext
              Transfer Protocol -- HTTP/1.1", RFC 2616, June 1999.

   [RFC2434]  Narten, T. and H. Alvestrand, "Guidelines for Writing an
              IANA Considerations Section in RFCs", BCP 26, RFC 2434,
              October 1998.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.











Levi & Schoenwaelder        Standards Track                    [Page 62]
^L
RFC 3165                       Script MIB                    August 2001


15.  Editors' Addresses

   David B. Levi
   Nortel Networks
   4401 Great America Parkway
   Santa Clara, CA 95052-8185
   USA

   Phone: +1 423 686 0432
   EMail: dlevi@nortelnetworks.com


   Juergen Schoenwaelder
   TU Braunschweig
   Bueltenweg 74/75
   38106 Braunschweig
   Germany

   Phone: +49 531 391-3283
   EMail: schoenw@ibr.cs.tu-bs.de































Levi & Schoenwaelder        Standards Track                    [Page 63]
^L
RFC 3165                       Script MIB                    August 2001


16.  Full Copyright Statement

   Copyright (C) The Internet Society (2001).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.



















Levi & Schoenwaelder        Standards Track                    [Page 64]
^L