path: root/doc/rfc/rfc3533.txt

Network Working Group                                        S. Pfeiffer
Request for Comments: 3533                                         CSIRO
Category: Informational                                         May 2003


                 The Ogg Encapsulation Format Version 0

Status of this Memo

   This memo provides information for the Internet community.  It does
   not specify an Internet standard of any kind.  Distribution of this
   memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2003).  All Rights Reserved.

Abstract

   This document describes the Ogg bitstream format version 0, which is
   a general, freely-available encapsulation format for media streams.
   It is able to encapsulate any kind and number of video and audio
   encoding formats as well as other data streams in a single bitstream.

Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in BCP 14, RFC 2119 [2].

Table of Contents

   1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . .   2
   2. Definitions  . . . . . . . . . . . . . . . . . . . . . . . . .   2
   3. Requirements for a generic encapsulation format  . . . . . . .   3
   4. The Ogg bitstream format . . . . . . . . . . . . . . . . . . .   3
   5. The encapsulation process  . . . . . . . . . . . . . . . . . .   6
   6. The Ogg page format  . . . . . . . . . . . . . . . . . . . . .   9
   7. Security Considerations  . . . . . . . . . . . . . . . . . . .  11
   8. References . . . . . . . . . . . . . . . . . . . . . . . . . .  12
   A. Glossary of terms and abbreviations  . . . . . . . . . . . . .  13
   B. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . .  14
      Author's Address . . . . . . . . . . . . . . . . . . . . . . .  14
      Full Copyright Statement . . . . . . . . . . . . . . . . . . .  15







Pfeiffer                     Informational                      [Page 1]
^L
RFC 3533                          OGG                           May 2003


1. Introduction

   The Ogg bitstream format has been developed as a part of a larger
   project aimed at creating a set of components for the coding and
   decoding of multimedia content (codecs) which are to be freely
   available and freely re-implementable, both in software and in
   hardware for the computing community at large, including the Internet
   community.  It is the intention of the Ogg developers represented by
   Xiph.Org that it be usable without intellectual property concerns.

   This document describes the Ogg bitstream format and how to use it to
   encapsulate one or several media bitstreams created by one or several
   encoders.  The Ogg transport bitstream is designed to provide
   framing, error protection and seeking structure for higher-level
   codec streams that consist of raw, unencapsulated data packets, such
   as the Vorbis audio codec or the upcoming Tarkin and Theora video
   codecs.  It is capable of interleaving different binary media and
   other time-continuous data streams that are prepared by an encoder as
   a sequence of data packets.  Ogg provides enough information to
   properly separate data back into such encoder created data packets at
   the original packet boundaries without relying on decoding to find
   packet boundaries.

   Please note that the MIME type application/ogg has been registered
   with the IANA [1].

2. Definitions

   For describing the Ogg encapsulation process, a set of terms will be
   used whose meaning needs to be well understood.  Therefore, some of
   the most fundamental terms are defined now before we start with the
   description of the requirements for a generic media stream
   encapsulation format, the process of encapsulation, and the concrete
   format of the Ogg bitstream.  See the Appendix for a more complete
   glossary.

   The result of an Ogg encapsulation is called the "Physical (Ogg)
   Bitstream".  It encapsulates one or several encoder-created
   bitstreams, which are called "Logical Bitstreams".  A logical
   bitstream, provided to the Ogg encapsulation process, has a
   structure, i.e., it is split up into a sequence of so-called
   "Packets".  The packets are created by the encoder of that logical
   bitstream and represent meaningful entities for that encoder only
   (e.g., an uncompressed stream may use video frames as packets).  They
   do not contain boundary information - strung together they appear to
   be streams of random bytes with no landmarks.





Pfeiffer                     Informational                      [Page 2]
^L
RFC 3533                          OGG                           May 2003


   Please note that the term "packet" is not used in this document to
   signify entities for transport over a network.

3. Requirements for a generic encapsulation format

   The design idea behind Ogg was to provide a generic, linear media
   transport format to enable both file-based storage and stream-based
   transmission of one or several interleaved media streams independent
   of the encoding format of the media data.  Such an encapsulation
   format needs to provide:

   o  framing for logical bitstreams.

   o  interleaving of different logical bitstreams.

   o  detection of corruption.

   o  recapture after a parsing error.

   o  position landmarks for direct random access of arbitrary positions
      in the bitstream.

   o  streaming capability (i.e., no seeking is needed to build a 100%
      complete bitstream).

   o  small overhead (i.e., use no more than approximately 1-2% of
      bitstream bandwidth for packet boundary marking, high-level
      framing, sync and seeking).

   o  simplicity to enable fast parsing.

   o  simple concatenation mechanism of several physical bitstreams.

   All of these design considerations have been taken into consideration
   for Ogg.  Ogg supports framing and interleaving of logical
   bitstreams, seeking landmarks, detection of corruption, and stream
   resynchronisation after a parsing error with no more than
   approximately 1-2% overhead.  It is a generic framework to perform
   encapsulation of time-continuous bitstreams.  It does not know any
   specifics about the codec data that it encapsulates and is thus
   independent of any media codec.

4. The Ogg bitstream format

   A physical Ogg bitstream consists of multiple logical bitstreams
   interleaved in so-called "Pages".  Whole pages are taken in order
   from multiple logical bitstreams multiplexed at the page level.  The
   logical bitstreams are identified by a unique serial number in the



Pfeiffer                     Informational                      [Page 3]
^L
RFC 3533                          OGG                           May 2003


   header of each page of the physical bitstream.  This unique serial
   number is created randomly and does not have any connection to the
   content or encoder of the logical bitstream it represents.  Pages of
   all logical bitstreams are concurrently interleaved, but they need
   not be in a regular order - they are only required to be consecutive
   within the logical bitstream.  Ogg demultiplexing reconstructs the
   original logical bitstreams from the physical bitstream by taking the
   pages in order from the physical bitstream and redirecting them into
   the appropriate logical decoding entity.

   Each Ogg page contains only one type of data as it belongs to one
   logical bitstream only.  Pages are of variable size and have a page
   header containing encapsulation and error recovery information.  Each
   logical bitstream in a physical Ogg bitstream starts with a special
   start page (bos=beginning of stream) and ends with a special page
   (eos=end of stream).

   The bos page contains information to uniquely identify the codec type
   and MAY contain information to set up the decoding process.  The bos
   page SHOULD also contain information about the encoded media - for
   example, for audio, it should contain the sample rate and number of
   channels.  By convention, the first bytes of the bos page contain
   magic data that uniquely identifies the required codec.  It is the
   responsibility of anyone fielding a new codec to make sure it is
   possible to reliably distinguish his/her codec from all other codecs
   in use.  There is no fixed way to detect the end of the codec-
   identifying marker.  The format of the bos page is dependent on the
   codec and therefore MUST be given in the encapsulation specification
   of that logical bitstream type.  Ogg also allows but does not require
   secondary header packets after the bos page for logical bitstreams
   and these must also precede any data packets in any logical
   bitstream.  These subsequent header packets are framed into an
   integral number of pages, which will not contain any data packets.
   So, a physical bitstream begins with the bos pages of all logical
   bitstreams containing one initial header packet per page, followed by
   the subsidiary header packets of all streams, followed by pages
   containing data packets.

   The encapsulation specification for one or more logical bitstreams is
   called a "media mapping".  An example for a media mapping is "Ogg
   Vorbis", which uses the Ogg framework to encapsulate Vorbis-encoded
   audio data for stream-based storage (such as files) and transport
   (such as TCP streams or pipes).  Ogg Vorbis provides the name and
   revision of the Vorbis codec, the audio rate and the audio quality on
   the Ogg Vorbis bos page.  It also uses two additional header pages
   per logical bitstream.  The Ogg Vorbis bos page starts with the byte
   0x01, followed by "vorbis" (a total of 7 bytes of identifier).




Pfeiffer                     Informational                      [Page 4]
^L
RFC 3533                          OGG                           May 2003


   Ogg knows two types of multiplexing: concurrent multiplexing (so-
   called "Grouping") and sequential multiplexing (so-called
   "Chaining").  Grouping defines how to interleave several logical
   bitstreams page-wise in the same physical bitstream.  Grouping is for
   example needed for interleaving a video stream with several
   synchronised audio tracks using different codecs in different logical
   bitstreams.  Chaining on the other hand, is defined to provide a
   simple mechanism to concatenate physical Ogg bitstreams, as is often
   needed for streaming applications.

   In grouping, all bos pages of all logical bitstreams MUST appear
   together at the beginning of the Ogg bitstream.  The media mapping
   specifies the order of the initial pages.  For example, the grouping
   of a specific Ogg video and Ogg audio bitstream may specify that the
   physical bitstream MUST begin with the bos page of the logical video
   bitstream, followed by the bos page of the audio bitstream.  Unlike
   bos pages, eos pages for the logical bitstreams need not all occur
   contiguously.  Eos pages may be 'nil' pages, that is, pages
   containing no content but simply a page header with position
   information and the eos flag set in the page header.  Each grouped
   logical bitstream MUST have a unique serial number within the scope
   of the physical bitstream.

   In chaining, complete logical bitstreams are concatenated.  The
   bitstreams do not overlap, i.e., the eos page of a given logical
   bitstream is immediately followed by the bos page of the next.  Each
   chained logical bitstream MUST have a unique serial number within the
   scope of the physical bitstream.

   It is possible to consecutively chain groups of concurrently
   multiplexed bitstreams.  The groups, when unchained, MUST stand on
   their own as a valid concurrently multiplexed bitstream.  The
   following diagram shows a schematic example of such a physical
   bitstream that obeys all the rules of both grouped and chained
   multiplexed bitstreams.

               physical bitstream with pages of
          different logical bitstreams grouped and chained
      -------------------------------------------------------------
      |*A*|*B*|*C*|A|A|C|B|A|B|#A#|C|...|B|C|#B#|#C#|*D*|D|...|#D#|
      -------------------------------------------------------------
       bos bos bos             eos           eos eos bos       eos

   In this example, there are two chained physical bitstreams, the first
   of which is a grouped stream of three logical bitstreams A, B, and C.
   The second physical bitstream is chained after the end of the grouped
   bitstream, which ends after the last eos page of all its grouped
   logical bitstreams.  As can be seen, grouped bitstreams begin



Pfeiffer                     Informational                      [Page 5]
^L
RFC 3533                          OGG                           May 2003


   together - all of the bos pages MUST appear before any data pages.
   It can also be seen that pages of concurrently multiplexed bitstreams
   need not conform to a regular order.  And it can be seen that a
   grouped bitstream can end long before the other bitstreams in the
   group end.

   Ogg does not know any specifics about the codec data except that each
   logical bitstream belongs to a different codec, the data from the
   codec comes in order and has position markers (so-called "Granule
   positions").  Ogg does not have a concept of 'time': it only knows
   about sequentially increasing, unitless position markers.  An
   application can only get temporal information through higher layers
   which have access to the codec APIs to assign and convert granule
   positions or time.

   A specific definition of a media mapping using Ogg may put further
   constraints on its specific use of the Ogg bitstream format.  For
   example, a specific media mapping may require that all the eos pages
   for all grouped bitstreams need to appear in direct sequence.  An
   example for a media mapping is the specification of "Ogg Vorbis".
   Another example is the upcoming "Ogg Theora" specification which
   encapsulates Theora-encoded video data and usually comes multiplexed
   with a Vorbis stream for an Ogg containing synchronised audio and
   video.  As Ogg does not specify temporal relationships between the
   encapsulated concurrently multiplexed bitstreams, the temporal
   synchronisation between the audio and video stream will be specified
   in this media mapping.  To enable streaming, pages from various
   logical bitstreams will typically be interleaved in chronological
   order.

5. The encapsulation process

   The process of multiplexing different logical bitstreams happens at
   the level of pages as described above.  The bitstreams provided by
   encoders are however handed over to Ogg as so-called "Packets" with
   packet boundaries dependent on the encoding format.  The process of
   encapsulating packets into pages will be described now.

   From Ogg's perspective, packets can be of any arbitrary size.  A
   specific media mapping will define how to group or break up packets
   from a specific media encoder.  As Ogg pages have a maximum size of
   about 64 kBytes, sometimes a packet has to be distributed over
   several pages.  To simplify that process, Ogg divides each packet
   into 255 byte long chunks plus a final shorter chunk.  These chunks
   are called "Ogg Segments".  They are only a logical construct and do
   not have a header for themselves.





Pfeiffer                     Informational                      [Page 6]
^L
RFC 3533                          OGG                           May 2003


   A group of contiguous segments is wrapped into a variable length page
   preceded by a header.  A segment table in the page header tells about
   the "Lacing values" (sizes) of the segments included in the page.  A
   flag in the page header tells whether a page contains a packet
   continued from a previous page.  Note that a lacing value of 255
   implies that a second lacing value follows in the packet, and a value
   of less than 255 marks the end of the packet after that many
   additional bytes.  A packet of 255 bytes (or a multiple of 255 bytes)
   is terminated by a lacing value of 0.  Note also that a 'nil' (zero
   length) packet is not an error; it consists of nothing more than a
   lacing value of zero in the header.

   The encoding is optimized for speed and the expected case of the
   majority of packets being between 50 and 200 bytes large.  This is a
   design justification rather than a recommendation.  This encoding
   both avoids imposing a maximum packet size as well as imposing
   minimum overhead on small packets.  In contrast, e.g., simply using
   two bytes at the head of every packet and having a max packet size of
   32 kBytes would always penalize small packets (< 255 bytes, the
   typical case) with twice the segmentation overhead.  Using the lacing
   values as suggested, small packets see the minimum possible byte-
   aligned overhead (1 byte) and large packets (>512 bytes) see a fairly
   constant ~0.5% overhead on encoding space.




























Pfeiffer                     Informational                      [Page 7]
^L
RFC 3533                          OGG                           May 2003


   The following diagram shows a schematic example of a media mapping
   using Ogg and grouped logical bitstreams:

          logical bitstream with packet boundaries
 -----------------------------------------------------------------
 > |       packet_1             | packet_2         | packet_3 |  <
 -----------------------------------------------------------------

                     |segmentation (logically only)
                     v

      packet_1 (5 segments)          packet_2 (4 segs)    p_3 (2 segs)
     ------------------------------ -------------------- ------------
 ..  |seg_1|seg_2|seg_3|seg_4|s_5 | |seg_1|seg_2|seg_3|| |seg_1|s_2 | ..
     ------------------------------ -------------------- ------------

                     | page encapsulation
                     v

 page_1 (packet_1 data)   page_2 (pket_1 data)   page_3 (packet_2 data)
------------------------  ----------------  ------------------------
|H|------------------- |  |H|----------- |  |H|------------------- |
|D||seg_1|seg_2|seg_3| |  |D|seg_4|s_5 | |  |D||seg_1|seg_2|seg_3| | ...
|R|------------------- |  |R|----------- |  |R|------------------- |
------------------------  ----------------  ------------------------

                    |
pages of            |
other    --------|  |
logical         -------
bitstreams      | MUX |
                -------
                   |
                   v

              page_1  page_2          page_3
      ------  ------  -------  -----  -------
 ...  ||   |  ||   |  ||    |  ||  |  ||    |  ...
      ------  ------  -------  -----  -------
              physical Ogg bitstream

   In this example we take a snapshot of the encapsulation process of
   one logical bitstream.  We can see part of that bitstream's
   subdivision into packets as provided by the codec.  The Ogg
   encapsulation process chops up the packets into segments.  The
   packets in this example are rather large such that packet_1 is split
   into 5 segments - 4 segments with 255 bytes and a final smaller one.
   Packet_2 is split into 4 segments - 3 segments with 255 bytes and a



Pfeiffer                     Informational                      [Page 8]
^L
RFC 3533                          OGG                           May 2003


   final very small one - and packet_3 is split into two segments.  The
   encapsulation process then creates pages, which are quite small in
   this example.  Page_1 consists of the first three segments of
   packet_1, page_2 contains the remaining 2 segments from packet_1, and
   page_3 contains the first three pages of packet_2.  Finally, this
   logical bitstream is multiplexed into a physical Ogg bitstream with
   pages of other logical bitstreams.

6. The Ogg page format

   A physical Ogg bitstream consists of a sequence of concatenated
   pages.  Pages are of variable size, usually 4-8 kB, maximum 65307
   bytes.  A page header contains all the information needed to
   demultiplex the logical bitstreams out of the physical bitstream and
   to perform basic error recovery and landmarks for seeking.  Each page
   is a self-contained entity such that the page decode mechanism can
   recognize, verify, and handle single pages at a time without
   requiring the overall bitstream.

   The Ogg page header has the following format:

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1| Byte
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| capture_pattern: Magic number for page start "OggS"           | 0-3
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| version       | header_type   | granule_position              | 4-7
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               | 8-11
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                               | bitstream_serial_number       | 12-15
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                               | page_sequence_number          | 16-19
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                               | CRC_checksum                  | 20-23
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                               |page_segments  | segment_table | 24-27
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ...                                                           | 28-
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The LSb (least significant bit) comes first in the Bytes.  Fields
   with more than one byte length are encoded LSB (least significant
   byte) first.







Pfeiffer                     Informational                      [Page 9]
^L
RFC 3533                          OGG                           May 2003


   The fields in the page header have the following meaning:

   1. capture_pattern: a 4 Byte field that signifies the beginning of a
      page.  It contains the magic numbers:

            0x4f 'O'

            0x67 'g'

            0x67 'g'

            0x53 'S'

      It helps a decoder to find the page boundaries and regain
      synchronisation after parsing a corrupted stream.  Once the
      capture pattern is found, the decoder verifies page sync and
      integrity by computing and comparing the checksum.

   2. stream_structure_version: 1 Byte signifying the version number of
      the Ogg file format used in this stream (this document specifies
      version 0).

   3. header_type_flag: the bits in this 1 Byte field identify the
      specific type of this page.

      *  bit 0x01

         set: page contains data of a packet continued from the previous
            page

         unset: page contains a fresh packet

      *  bit 0x02

         set: this is the first page of a logical bitstream (bos)

         unset: this page is not a first page

      *  bit 0x04

         set: this is the last page of a logical bitstream (eos)

         unset: this page is not a last page

   4. granule_position: an 8 Byte field containing position information.
      For example, for an audio stream, it MAY contain the total number
      of PCM samples encoded after including all frames finished on this
      page.  For a video stream it MAY contain the total number of video



Pfeiffer                     Informational                     [Page 10]
^L
RFC 3533                          OGG                           May 2003


      frames encoded after this page.  This is a hint for the decoder
      and gives it some timing and position information.  Its meaning is
      dependent on the codec for that logical bitstream and specified in
      a specific media mapping.  A special value of -1 (in two's
      complement) indicates that no packets finish on this page.

   5. bitstream_serial_number: a 4 Byte field containing the unique
      serial number by which the logical bitstream is identified.

   6. page_sequence_number: a 4 Byte field containing the sequence
      number of the page so the decoder can identify page loss.  This
      sequence number is increasing on each logical bitstream
      separately.

   7. CRC_checksum: a 4 Byte field containing a 32 bit CRC checksum of
      the page (including header with zero CRC field and page content).
      The generator polynomial is 0x04c11db7.

   8. number_page_segments: 1 Byte giving the number of segment entries
      encoded in the segment table.

   9. segment_table: number_page_segments Bytes containing the lacing
      values of all segments in this page.  Each Byte contains one
      lacing value.

   The total header size in bytes is given by:
   header_size = number_page_segments + 27 [Byte]

   The total page size in Bytes is given by:
   page_size = header_size + sum(lacing_values: 1..number_page_segments)
   [Byte]

7. Security Considerations

   The Ogg encapsulation format is a container format and only
   encapsulates content (such as Vorbis-encoded audio).  It does not
   provide for any generic encryption or signing of itself or its
   contained content bitstreams.  However, it encapsulates any kind of
   content bitstream as long as there is a codec for it, and is thus
   able to contain encrypted and signed content data.  It is also
   possible to add an external security mechanism that encrypts or signs
   an Ogg physical bitstream and thus provides content confidentiality
   and authenticity.

   As Ogg encapsulates binary data, it is possible to include executable
   content in an Ogg bitstream.  This can be an issue with applications
   that are implemented using the Ogg format, especially when Ogg is
   used for streaming or file transfer in a networking scenario.  As



Pfeiffer                     Informational                     [Page 11]
^L
RFC 3533                          OGG                           May 2003


   such, Ogg does not pose a threat there.  However, an application
   decoding Ogg and its encapsulated content bitstreams has to ensure
   correct handling of manipulated bitstreams, of buffer overflows and
   the like.

8. References

   [1] Walleij, L., "The application/ogg Media Type", RFC 3534, May
       2003.

   [2] Bradner, S., "Key words for use in RFCs to Indicate Requirement
       Levels", BCP 14, RFC 2119, March 1997.







































Pfeiffer                     Informational                     [Page 12]
^L
RFC 3533                          OGG                           May 2003


Appendix A. Glossary of terms and abbreviations

   bos page: The initial page (beginning of stream) of a logical
      bitstream which contains information to identify the codec type
      and other decoding-relevant information.

   chaining (or sequential multiplexing): Concatenation of two or more
      complete physical Ogg bitstreams.

   eos page: The final page (end of stream) of a logical bitstream.

   granule position: An increasing position number for a specific
      logical bitstream stored in the page header.  Its meaning is
      dependent on the codec for that logical bitstream and specified in
      a specific media mapping.

   grouping (or concurrent multiplexing): Interleaving of pages of
      several logical bitstreams into one complete physical Ogg
      bitstream under the restriction that all bos pages of all grouped
      logical bitstreams MUST appear before any data pages.

   lacing value: An entry in the segment table of a page header
      representing the size of the related segment.

   logical bitstream: A sequence of bits being the result of an encoded
      media stream.

   media mapping: A specific use of the Ogg encapsulation format
      together with a specific (set of) codec(s).

   (Ogg) packet: A subpart of a logical bitstream that is created by the
      encoder for that bitstream and represents a meaningful entity for
      the encoder, but only a sequence of bits to the Ogg encapsulation.

   (Ogg) page: A physical bitstream consists of a sequence of Ogg pages
      containing data of one logical bitstream only.  It usually
      contains a group of contiguous segments of one packet only, but
      sometimes packets are too large and need to be split over several
      pages.

   physical (Ogg) bitstream: The sequence of bits resulting from an Ogg
      encapsulation of one or several logical bitstreams.  It consists
      of a sequence of pages from the logical bitstreams with the
      restriction that the pages of one logical bitstream MUST come in
      their correct temporal order.






Pfeiffer                     Informational                     [Page 13]
^L
RFC 3533                          OGG                           May 2003


   (Ogg) segment: The Ogg encapsulation process splits each packet into
      chunks of 255 bytes plus a last fractional chunk of less than 255
      bytes.  These chunks are called segments.

Appendix B. Acknowledgements

   The author gratefully acknowledges the work that Christopher
   Montgomery  and the Xiph.Org foundation have done in defining the Ogg
   multimedia project and as part of it the open file format described
   in this document.  The author hopes that providing this document to
   the Internet community will help in promoting the Ogg multimedia
   project at http://www.xiph.org/.  Many thanks also for the many
   technical and typo corrections that C. Montgomery and the Ogg
   community provided as feedback to this RFC.

Author's Address

   Silvia Pfeiffer
   CSIRO, Australia
   Locked Bag 17
   North Ryde, NSW  2113
   Australia

   Phone: +61 2 9325 3141
   EMail: Silvia.Pfeiffer@csiro.au
   URI:   http://www.cmis.csiro.au/Silvia.Pfeiffer/

























Pfeiffer                     Informational                     [Page 14]
^L
RFC 3533                          OGG                           May 2003


Full Copyright Statement

   Copyright (C) The Internet Society (2003).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.



















Pfeiffer                     Informational                     [Page 15]
^L