path: root/doc/rfc/rfc7554.txt

Internet Engineering Task Force (IETF)                  T. Watteyne, Ed.
Request for Comments: 7554                             Linear Technology
Category: Informational                                    M. Palattella
ISSN: 2070-1721                                 University of Luxembourg
                                                               L. Grieco
                                                     Politecnico di Bari
                                                                May 2015


    Using IEEE 802.15.4e Time-Slotted Channel Hopping (TSCH) in the
              Internet of Things (IoT): Problem Statement

Abstract

   This document describes the environment, problem statement, and goals
   for using the Time-Slotted Channel Hopping (TSCH) Medium Access
   Control (MAC) protocol of IEEE 802.14.4e in the context of Low-Power
   and Lossy Networks (LLNs).  The set of goals enumerated in this
   document form an initial set only.

Status of This Memo

   This document is not an Internet Standards Track specification; it is
   published for informational purposes.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Not all documents
   approved by the IESG are a candidate for any level of Internet
   Standard; see Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc7554.
















Watteyne, et al.              Informational                     [Page 1]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


Copyright Notice

   Copyright (c) 2015 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.





































Watteyne, et al.              Informational                     [Page 2]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   4
   2.  TSCH in the LLN Context . . . . . . . . . . . . . . . . . . .   5
   3.  Problems and Goals  . . . . . . . . . . . . . . . . . . . . .   7
     3.1.  Network Formation . . . . . . . . . . . . . . . . . . . .   8
     3.2.  Network Maintenance . . . . . . . . . . . . . . . . . . .   8
     3.3.  Multi-Hop Topology  . . . . . . . . . . . . . . . . . . .   8
     3.4.  Routing and Timing Parents  . . . . . . . . . . . . . . .   8
     3.5.  Resource Management . . . . . . . . . . . . . . . . . . .   9
     3.6.  Dataflow Control  . . . . . . . . . . . . . . . . . . . .   9
     3.7.  Deterministic Behavior  . . . . . . . . . . . . . . . . .   9
     3.8.  Scheduling Mechanisms . . . . . . . . . . . . . . . . . .  10
     3.9.  Secure Communication  . . . . . . . . . . . . . . . . . .  10
   4.  Security Considerations . . . . . . . . . . . . . . . . . . .  11
   5.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  11
     5.1.  Normative References  . . . . . . . . . . . . . . . . . .  11
     5.2.  Informative References  . . . . . . . . . . . . . . . . .  11
   Appendix A.  TSCH Protocol Highlights . . . . . . . . . . . . . .  15
     A.1.  Time Slots  . . . . . . . . . . . . . . . . . . . . . . .  15
     A.2.  Slotframes  . . . . . . . . . . . . . . . . . . . . . . .  15
     A.3.  Node TSCH Schedule  . . . . . . . . . . . . . . . . . . .  15
     A.4.  Cells and Bundles . . . . . . . . . . . . . . . . . . . .  16
     A.5.  Dedicated vs. Shared Cells  . . . . . . . . . . . . . . .  17
     A.6.  Absolute Slot Number  . . . . . . . . . . . . . . . . . .  17
     A.7.  Channel Hopping . . . . . . . . . . . . . . . . . . . . .  17
     A.8.  Time Synchronization  . . . . . . . . . . . . . . . . . .  18
     A.9.  Power Consumption . . . . . . . . . . . . . . . . . . . .  19
     A.10. Network TSCH Schedule . . . . . . . . . . . . . . . . . .  19
     A.11. Join Process  . . . . . . . . . . . . . . . . . . . . . .  19
     A.12. Information Elements  . . . . . . . . . . . . . . . . . .  20
     A.13. Extensibility . . . . . . . . . . . . . . . . . . . . . .  20
   Appendix B.  TSCH Features  . . . . . . . . . . . . . . . . . . .  21
     B.1.  Collision-Free Communication  . . . . . . . . . . . . . .  21
     B.2.  Multi-Channel vs. Channel Hopping . . . . . . . . . . . .  21
     B.3.  Cost of (Continuous) Synchronization  . . . . . . . . . .  21
     B.4.  Topology Stability  . . . . . . . . . . . . . . . . . . .  21
     B.5.  Multiple Concurrent Slotframes  . . . . . . . . . . . . .  22
   Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . .  22
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  23











Watteyne, et al.              Informational                     [Page 3]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


1.  Introduction

   IEEE 802.15.4e [IEEE.802.15.4e] was published in 2012 as an amendment
   to the Medium Access Control (MAC) protocol defined by the IEEE
   802.15.4 standard (of 2011) [IEEE.802.15.4].  IEEE 802.15.4e will be
   rolled into the next revision of IEEE 802.15.4, scheduled to be
   published in 2015.  The Time-Slotted Channel Hopping (TSCH) mode of
   IEEE 802.15.4e is the object of this document.  The term "TSCH"
   refers to TSCH as used in [IEEE.802.15.4e].

   This document describes the main issues arising from the adoption of
   the TSCH in the LLN context, following the terminology defined in
   [TERMS-6TISCH].  Appendix A further gives an overview of the key
   features of the TSCH amendment to IEEE 802.15.4e.  Appendix B details
   features of TSCH, which might be interesting for the work of the
   6TiSCH WG.

   TSCH was designed to allow IEEE 802.15.4 devices to support a wide
   range of applications including, but not limited to, industrial ones
   [IEEE.802.15.4e].  At its core is a medium access technique that uses
   time synchronization to achieve low-power operation and channel
   hopping to enable high reliability.  Synchronization accuracy impacts
   power consumption and can vary from microseconds to milliseconds
   depending on the solution.  This is very different from the "legacy"
   IEEE 802.15.4 MAC protocol and is therefore better described as a
   "redesign".  TSCH does not amend the physical layer, i.e., it can
   operate on any hardware that is compliant with IEEE 802.15.4.

   IEEE 802.15.4e is the latest generation of ultra-lower power and
   reliable networking solutions for LLNs.  [RFC5673] discusses
   industrial applications and highlights the harsh operating conditions
   as well as the stringent reliability, availability, and security
   requirements for an LLN to operate in an industrial environment.  In
   these environments, vast deployment environments with large
   (metallic) equipment cause multi-path fading and interference to
   thwart any attempt of a single-channel solution to be reliable; the
   channel agility of TSCH is the key to its ultra-high reliability.
   Commercial networking solutions are available today in which nodes
   consume 10's of microamps on average [CurrentCalculator] with end-to-
   end packet delivery ratios over 99.999% [Doherty07channel].

   IEEE 802.15.4e has been designed for low-power constrained devices,
   often called "motes".  Several terms are used in the IETF to refer to
   those devices, including "LLN nodes" [RFC7102] and "constrained
   nodes" [RFC7228].  In this document, we use the generic (and shorter)
   term "node", used as a synonym for "LLN node", "constrained node", or
   "mote".




Watteyne, et al.              Informational                     [Page 4]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


   Enabling the LLN protocol stack to operate in industrial environments
   opens up new application domains for these networks.  Sensors
   deployed in smart cities [RFC5548] will be able to be installed for
   years without needing battery replacement.  "Umbrella" networks will
   interconnect smart elements from different entities in smart
   buildings [RFC5867].  Peel-and-stick switches will obsolete the need
   for costly conduits for lighting solutions in smart homes [RFC5826].

   TSCH focuses on the MAC layer only.  This clean layering allows for
   TSCH to fit under an IPv6-enabled protocol stack for LLNs, running an
   IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN)
   [RFC6282], the IPv6 Routing Protocol for Low-Power and Lossy Networks
   (RPL) [RFC6550], and the Constrained Application Protocol (CoAP)
   [RFC7252].  What is missing is a functional entity that is in charge
   of scheduling TSCH time slots for frames to be sent on.  In this
   document, we refer to this entity as the "Logical Link Control"
   (LLC), bearing in mind that realizations of this entity can be of
   different types, including a distributed protocol or a centralized
   server in charge of scheduling.

   While [IEEE.802.15.4e] defines the mechanisms for a TSCH node to
   communicate, it does not define the policies to build and maintain
   the communication schedule, match that schedule to the multi-hop
   paths maintained by RPL, adapt the resources allocated between
   neighbor nodes to the data traffic flows, enforce a differentiated
   treatment for data generated at the application layer and signaling
   messages needed by 6LoWPAN and RPL to discover neighbors, react to
   topology changes, self-configure IP addresses, or manage keying
   material.

   In other words, TSCH is designed to allow optimizations and strong
   customizations, simplifying the merging of TSCH with a protocol stack
   based on IPv6, 6LoWPAN, and RPL.

2.  TSCH in the LLN Context

   To map the services required by the IP layer to the services provided
   by the link layer, an adaptation layer is used
   [Palattella12standardized].  In 2007, the 6LoWPAN WG started working
   on specifications for transmitting IPv6 packets over IEEE 802.15.4
   networks [RFC4919].  A low-power Wireless Personal Area Network
   (WPAN) is typically composed of a large number of battery-powered
   devices that are deployed at locations that are unknown a priori.
   Nodes form a star or a mesh topology and communicate with one another
   at a low datarate and using short frames.  The wireless nature of the
   links means that they are unreliable in nature.  Nodes turn off their
   radio interface most of the time to conserve energy.  Given these




Watteyne, et al.              Informational                     [Page 5]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


   features, it is clear that the adoption of IPv6 on top of a low-power
   WPAN is not straightforward but poses strong requirements for the
   optimization of this adaptation layer.

   For instance, due to the IPv6 default minimum MTU size (1280 bytes),
   an unfragmented IPv6 packet is too large to fit in an IEEE 802.15.4
   frame.  Moreover, the overhead due to the 40-byte-long IPv6 header
   wastes the scarce bandwidth available at the PHY layer [RFC4944].
   For these reasons, the 6LoWPAN WG has defined an effective adaptation
   layer [RFC6282].  Further issues encompass the autoconfiguration of
   IPv6 addresses [RFC2460] [RFC4862], the compliance with the
   recommendation on supporting link-layer subnet broadcast in shared
   networks [RFC3819], the reduction of routing and management overhead
   [RFC6606], the adoption of lightweight application protocols (or
   novel data encoding techniques), and the support for security
   mechanisms (confidentiality and integrity protection, device
   bootstrapping, key establishment, and management).

   These features can run on top of TSCH.  There are, however, important
   issues to solve, as highlighted in Section 3.

   Routing issues are challenging for 6LoWPAN, given the low-power and
   lossy radio links, the battery-powered nodes, the multi-hop mesh
   topologies, and the frequent topology changes due to mobility.
   Successful solutions take into account the specific application
   requirements, along with IPv6 behavior and 6LoWPAN mechanisms
   [Palattella12standardized].  The ROLL WG has defined RPL in
   [RFC6550].  RPL can support a wide variety of link layers, including
   ones that are constrained, potentially lossy, or typically utilized
   in conjunction with host or router devices with very limited
   resources, as in building/home automation [RFC5867] [RFC5826],
   industrial environments [RFC5673], and urban applications [RFC5548].
   RPL is able to quickly build up network routes, distribute routing
   knowledge among nodes, and adapt to a changing topology.  In a
   typical setting, nodes are connected through multi-hop paths to a
   small set of root devices, which are usually responsible for data
   collection and coordination.  For each of them, a Destination-
   Oriented Directed Acyclic Graph (DODAG) is created by accounting for
   link costs, node attributes/status information, and an Objective
   Function, which maps the optimization requirements of the target
   scenario.

   The topology is set up based on a Rank metric, which encodes the
   distance of each node with respect to its reference root, as
   specified by the Objective Function.  Regardless of the way it is
   computed, the Rank monotonically decreases along the DODAG towards
   the root, building a gradient.  RPL encompass different kinds of
   traffic and signaling information.  Multipoint-to-Point (MP2P) is the



Watteyne, et al.              Informational                     [Page 6]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


   dominant traffic in LLN applications.  Data is routed towards nodes
   with some application relevance, such as the LLN gateway to the
   larger Internet or to the core of private IP networks.  In general,
   these destinations are the DODAG roots and act as data collection
   points for distributed monitoring applications.  Point-to-Multipoint
   (P2MP) data streams are used for actuation purposes, where messages
   are sent from DODAG roots to destination nodes.  Point-to-Point (P2P)
   traffic allows communication between two devices belonging to the
   same LLN, such as a sensor and an actuator.  A packet flows from the
   source to the common ancestor of those two communicating devices,
   then downward towards the destination.  Therefore, RPL has to
   discover both upward routes (i.e., from nodes to DODAG roots) in
   order to enable MP2P and P2P flows and downward routes (i.e., from
   DODAG roots to nodes) to support P2MP and P2P traffic.

   Section 3 highlights the challenges that need to be addressed to use
   RPL on top of TSCH.

   Open-source initiatives have emerged around TSCH, with the OpenWSN
   project [OpenWSN] [OpenWSNETT] being the first open-source
   implementation of a standards-based protocol stack.  This
   implementation was used as the foundation for an IP for the Smart
   Objects Alliance (IPSO) [IPSO] interoperability event in 2011.  In
   the absence of a standardized scheduling mechanism for TSCH, a
   "slotted Aloha" schedule was used.

3.  Problems and Goals

   As highlighted in Appendix A, TSCH differs from other low-power MAC
   protocols because of its scheduled nature.  TSCH defines the
   mechanisms to execute a communication schedule; yet, it is the entity
   that sets up the schedule that controls the topology of the network.
   This scheduling entity also controls the resources allocated to each
   link in that topology.

   How this entity should operate is out of scope of TSCH.  The
   remainder of this section highlights the problems this entity needs
   to address.  For simplicity, we refer to this entity by the generic
   name "LLC".  Note that the 6top sublayer, currently being defined in
   [SUBLAYER-6top], can be seen as an embodiment of this generic "LLC".

   Some of the issues the LLC needs to target might overlap with the
   scope of other protocols (e.g., 6LoWPAN, RPL, and RSVP).  In this
   case, the LLC will profit from the services provided by other
   protocols to pursue these objectives.






Watteyne, et al.              Informational                     [Page 7]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


3.1.  Network Formation

   The LLC needs to control the way the network is formed, including how
   new nodes join and how already joined nodes advertise the presence of
   the network.  The LLC needs to:

   1.  Define the Information Elements included in the Enhanced Beacons
       (EBs) [IEEE.802.15.4e] advertising the presence of the network.

   2.  (For a new node), define rules to process and filter received
       EBs.

   3.  Define the joining procedure.  This might include a mechanism to
       assign a unique 16-bit address to a node and the management of
       initial keying material.

   4.  Define a mechanism to secure the joining process and the
       subsequent optional process of scheduling more communication
       cells.

3.2.  Network Maintenance

   Once a network is formed, the LLC needs to maintain the network's
   health, allowing for nodes to stay synchronized.  The LLC needs to:

   1.  Manage each node's time source neighbor.

   2.  Define a mechanism for a node to update the join priority it
       announces in its EB.

   3.  Schedule transmissions of EBs to advertise the presence of the
       network.

3.3.  Multi-Hop Topology

   RPL, given a weighted connectivity graph, determines multi-hop
   routes.  The LLC needs to:

   1.  Define a mechanism to gather topological information, node and
       link state, which it can then feed to RPL.

   2.  Ensure that the TSCH schedule contains cells along the multi-hop
       routes identified by RPL (a cell in a TSCH schedule is an atomic
       "unit" of resource, see Section 3.5).

   3.  Where applicable, maintain independent sets of cells to transport
       independent flows of data.




Watteyne, et al.              Informational                     [Page 8]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


3.4.  Routing and Timing Parents

   At all times, a TSCH node needs to have a time-source neighbor to
   which it can synchronize.  Therefore, LLC needs to assign a time-
   source neighbor to allow for correct operation of the TSCH network.
   A time-source neighbor could, or not, be taken from the RPL routing
   parent set.

3.5.  Resource Management

   A cell in a TSCH schedule is an atomic "unit" of resource.  The
   number of cells to assign between neighbor nodes needs to be
   appropriate for the size of the traffic flow.  The LLC needs to:

   1.  Define a mechanism for neighbor nodes to exchange information
       about their schedule and, if applicable, negotiate the addition/
       deletion of cells.

   2.  Allow for an entity (e.g., a set of devices, a distributed
       protocol, a Path Computation Element (PCE), etc.) to take control
       of the schedule.

3.6.  Dataflow Control

   TSCH defines mechanisms for a node to signal when it cannot accept an
   incoming packet.  It does not, however, define the policy that
   determines when to stop accepting packets.  The LLC needs to:

   1.  Allow for the implementation and configuration of policy to queue
       incoming and outgoing packets.

   2.  Manage the buffer space, and indicate to TSCH when to stop
       accepting incoming packets.

   3.  Handle transmissions that have failed.  A transmission is
       declared failed when TSCH has retransmitted the packet multiple
       times, without receiving an acknowledgment.  This covers both
       dedicated and shared cells.

3.7.  Deterministic Behavior

   As highlighted in [RFC5673], in some applications, data is generated
   periodically and has a well-understood data bandwidth requirement,
   which is deterministic and predictable.  The LLC needs to:

   1.  Ensure that the data is delivered to its final destination before
       a deadline possibly determined by the application.




Watteyne, et al.              Informational                     [Page 9]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


   2.  Provide a mechanism for such deterministic flows to coexist with
       bursty or infrequent traffic flows of different priorities.

3.8.  Scheduling Mechanisms

   Several scheduling mechanisms can be envisioned and could possibly
   coexist in the same network.  For example, [RPL] describes how the
   allocation of bandwidth can be optimized by an external PCE
   [RFC4655].  Another centralized (PCE-based) traffic-aware scheduling
   algorithm is defined in [TASA-PIMRC].  Alternatively, two neighbor
   nodes can adapt the number of cells autonomously by monitoring the
   amount of traffic and negotiating the allocation to extra cell when
   needed.  An example of a decentralized algorithm (i.e., no PCE is
   needed) is provided in [Tinka10decentralized].  This mechanism can be
   used to establish multi-hop paths in a fashion similar to RSVP
   [RFC2205].  The LLC needs to:

   1.  Provide a mechanism for two devices to negotiate the allocation
       and deallocation of cells between them.

   2.  Provide a mechanism for the device to monitor and manage the
       capabilities of a node several hops away.

   3.  Define a mechanism for these different scheduling mechanisms to
       coexist in the same network.

3.9.  Secure Communication

   Given some keying material, TSCH defines mechanisms to encrypt and
   authenticate MAC frames.  It does not define how this keying material
   is generated.  The LLC needs to:

   1.  Define the keying material and authentication mechanism needed by
       a new node to join an existing network.

   2.  Define a mechanism to allow for the secure transfer of
       application data between neighbor nodes.

   3.  Define a mechanism to allow for the secure transfer of signaling
       data between nodes and the LLC.











Watteyne, et al.              Informational                    [Page 10]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


4.  Security Considerations

   This memo is an informational overview of existing standards and does
   not define any new mechanisms or protocols.

   It does describe the need for the 6TiSCH WG to define a secure
   solution.  In particular, Section 3.1 describes security in the join
   process.  Section 3.9 discusses data-frame protection.

5.  References

5.1.  Normative References

   [IEEE.802.15.4]
              IEEE, "IEEE Standard for Local and metropolitan area
              networks -- Part. 15.4: Low-Rate Wireless Personal Area
              Networks", IEEE Std. 802.15.4-2011, September 2011.

   [IEEE.802.15.4e]
              IEEE, "IEEE Standard for Local and metropolitan area
              networks -- Part 15.4: Low-Rate Wireless Personal Area
              Networks (LR-WPANs) Amendment 1: MAC sublayer", IEEE Std.
              802.15.4e-2012, April 2012.

5.2.  Informative References

   [CurrentCalculator]
              Linear Technology, "Application Note: Using the Current
              Calculator to Estimate Mote Power", August 2012,
              <http://www.linear.com/docs/43189>.

   [Doherty07channel]
              Doherty, L., Lindsay, W., and J. Simon, "Channel-Specific
              Wireless Sensor Network Path Data", IEEE International
              Conference on Computer Communications and Networks
              (ICCCN), pp. 89-94, 2007.

   [IPSO]     IPSO Alliance, "IP for Smart Objects Alliance Homepage",
              <http://www.ipso-alliance.org/>.

   [OpenWSN]  "Berkeley's OpenWSN Project Homepage",
              <http://www.openwsn.org/>.









Watteyne, et al.              Informational                    [Page 11]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


   [OpenWSNETT]
              Watteyne, T., Vilajosana, X., Kerkez, B., Chraim, F.,
              Weekly, K., Wang, Q., Glaser, S., and K. Pister, "OpenWSN:
              A Standards-Based Low-Power Wireless Development
              Environment", Transactions on Emerging Telecommunications
              Technologies, Volume 23: Issue 5, August 2012.

   [Palattella12standardized]
              Palattella, MR., Accettura, N., Vilajosana, X., Watteyne,
              T., Grieco, LA., Boggia, G., and M. Dohler, "Standardized
              Protocol Stack For The Internet Of (Important) Things",
              IEEE Communications Surveys and Tutorials, Volume: 15,
              Issue 3, December 2012.

   [RFC2205]  Braden, R., Ed., Zhang, L., Berson, S., Herzog, S., and S.
              Jamin, "Resource ReSerVation Protocol (RSVP) -- Version 1
              Functional Specification", RFC 2205, DOI 10.17487/RFC2205,
              September 1997, <http://www.rfc-editor.org/info/rfc2205>.

   [RFC2460]  Deering, S. and R. Hinden, "Internet Protocol, Version 6
              (IPv6) Specification", RFC 2460, DOI 10.17487/RFC2460,
              December 1998, <http://www.rfc-editor.org/info/rfc2460>.

   [RFC3819]  Karn, P., Ed., Bormann, C., Fairhurst, G., Grossman, D.,
              Ludwig, R., Mahdavi, J., Montenegro, G., Touch, J., and L.
              Wood, "Advice for Internet Subnetwork Designers", BCP 89,
              RFC 3819, DOI 10.17487/RFC3819, July 2004,
              <http://www.rfc-editor.org/info/rfc3819>.

   [RFC4655]  Farrel, A., Vasseur, J., and J. Ash, "A Path Computation
              Element (PCE)-Based Architecture", RFC 4655,
              DOI 10.17487/RFC4655, August 2006,
              <http://www.rfc-editor.org/info/rfc4655>.

   [RFC4862]  Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
              Address Autoconfiguration", RFC 4862,
              DOI 10.17487/RFC4862, September 2007,
              <http://www.rfc-editor.org/info/rfc4862>.

   [RFC4919]  Kushalnagar, N., Montenegro, G., and C. Schumacher, "IPv6
              over Low-Power Wireless Personal Area Networks (6LoWPANs):
              Overview, Assumptions, Problem Statement, and Goals",
              RFC 4919, DOI 10.17487/RFC4919, August 2007,
              <http://www.rfc-editor.org/info/rfc4919>.







Watteyne, et al.              Informational                    [Page 12]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


   [RFC4944]  Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler,
              "Transmission of IPv6 Packets over IEEE 802.15.4
              Networks", RFC 4944, DOI 10.17487/RFC4944, September 2007,
              <http://www.rfc-editor.org/info/rfc4944>.

   [RFC5548]  Dohler, M., Ed., Watteyne, T., Ed., Winter, T., Ed., and
              D. Barthel, Ed., "Routing Requirements for Urban Low-Power
              and Lossy Networks", RFC 5548, DOI 10.17487/RFC5548, May
              2009, <http://www.rfc-editor.org/info/rfc5548>.

   [RFC5673]  Pister, K., Ed., Thubert, P., Ed., Dwars, S., and T.
              Phinney, "Industrial Routing Requirements in Low-Power and
              Lossy Networks", RFC 5673, DOI 10.17487/RFC5673, October
              2009, <http://www.rfc-editor.org/info/rfc5673>.

   [RFC5826]  Brandt, A., Buron, J., and G. Porcu, "Home Automation
              Routing Requirements in Low-Power and Lossy Networks",
              RFC 5826, DOI 10.17487/RFC5826, April 2010,
              <http://www.rfc-editor.org/info/rfc5826>.

   [RFC5867]  Martocci, J., Ed., De Mil, P., Riou, N., and W. Vermeylen,
              "Building Automation Routing Requirements in Low-Power and
              Lossy Networks", RFC 5867, DOI 10.17487/RFC5867, June
              2010, <http://www.rfc-editor.org/info/rfc5867>.

   [RFC6282]  Hui, J., Ed. and P. Thubert, "Compression Format for IPv6
              Datagrams over IEEE 802.15.4-Based Networks", RFC 6282,
              DOI 10.17487/RFC6282, September 2011,
              <http://www.rfc-editor.org/info/rfc6282>.

   [RFC6550]  Winter, T., Ed., Thubert, P., Ed., Brandt, A., Hui, J.,
              Kelsey, R., Levis, P., Pister, K., Struik, R., Vasseur,
              JP., and R. Alexander, "RPL: IPv6 Routing Protocol for
              Low-Power and Lossy Networks", RFC 6550,
              DOI 10.17487/RFC6550, March 2012,
              <http://www.rfc-editor.org/info/rfc6550>.

   [RFC6606]  Kim, E., Kaspar, D., Gomez, C., and C. Bormann, "Problem
              Statement and Requirements for IPv6 over Low-Power
              Wireless Personal Area Network (6LoWPAN) Routing",
              RFC 6606, DOI 10.17487/RFC6606, May 2012,
              <http://www.rfc-editor.org/info/rfc6606>.

   [RFC7102]  Vasseur, JP., "Terms Used in Routing for Low-Power and
              Lossy Networks", RFC 7102, DOI 10.17487/RFC7102, January
              2014, <http://www.rfc-editor.org/info/rfc7102>.





Watteyne, et al.              Informational                    [Page 13]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


   [RFC7228]  Bormann, C., Ersue, M., and A. Keranen, "Terminology for
              Constrained-Node Networks", RFC 7228,
              DOI 10.17487/RFC7228, May 2014,
              <http://www.rfc-editor.org/info/rfc7228>.

   [RFC7252]  Shelby, Z., Hartke, K., and C. Bormann, "The Constrained
              Application Protocol (CoAP)", RFC 7252,
              DOI 10.17487/RFC7252, June 2014,
              <http://www.rfc-editor.org/info/rfc7252>.

   [RPL]      Phinney, T., Thubert, P., and R. Assimiti, "RPL
              applicability in industrial networks", Work in Progress,
              draft-ietf-roll-rpl-industrial-applicability-02, October
              2013.

   [SUBLAYER-6top]
              Wang, Q., Vilajosana, X., and T. Watteyne, "6TiSCH
              Operation Sublayer (6top)", Work in Progress, draft-wang-
              6tisch-6top-sublayer-01, July 2014.

   [TASA-PIMRC]
              Palattella, MR., Accettura, N., Dohler, M., Grieco, LA.,
              and G. Boggia, "Traffic Aware Scheduling Algorithm for
              reliable low-power multi-hop IEEE 802.15.4e networks",
              IEEE 23rd International Symposium on Personal, Indoor and
              Mobile Radio Communications (PIMRC), pp. 327-332,
              September 2012.

   [TERMS-6TISCH]
              Palattella, M., Thubert, P., Watteyne, T., and Q. Wang,
              "Terminology in IPv6 over the TSCH mode of IEEE
              802.15.4e", Work in Progress, draft-ietf-6tisch-
              terminology-04, March 2015.

   [Tinka10decentralized]
              Tinka, A., Watteyne, T., and K. Pister, "A Decentralized
              Scheduling Algorithm for Time Synchronized Channel
              Hopping", Ad Hoc Networks, 2010.

   [Watteyne09reliability]
              Watteyne, T., Mehta, A., and K. Pister, "Reliability
              Through Frequency Diversity: Why Channel Hopping Makes
              Sense", Proceedings of the 6th ACM Symposium on
              Performance Evaluation of Wireless Ad Hoc, Sensor, and
              Ubiquitous Networks (PE-WASUN), pp. 116-123, October 2009.






Watteyne, et al.              Informational                    [Page 14]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


Appendix A.  TSCH Protocol Highlights

   This appendix gives an overview of the key features of the IEEE
   802.15.4e TSCH amendment.  It makes no attempt at repeating the
   standard, rather it focuses on the following:

   o  Concepts that are sufficiently different from other IEEE 802.15.4
      networking that they may need to be defined and presented
      precisely.

   o  Techniques and ideas that are part of IEEE 802.15.4e and that
      might be useful for the work of the 6TiSCH WG.

A.1.  Time Slots

   All nodes in a TSCH network are synchronized.  Time is sliced up into
   time slots.  A time slot is long enough for a MAC frame of maximum
   size to be sent from node A to node B, and for node B to reply with
   an acknowledgment (ACK) frame indicating successful reception.

   The duration of a time slot is not defined by the standard.  With
   radios that are compliant with IEEE 802.15.4 operating in the 2.4 GHz
   frequency band, a maximum-length frame of 127 bytes takes about 4 ms
   to transmit; a shorter ACK takes about 1 ms.  With a 10 ms slot (a
   typical duration), this leaves 5 ms to radio turnaround, packet
   processing, and security operations.

A.2.  Slotframes

   Time slots are grouped into one of more slotframes.  A slotframe
   continuously repeats over time.  TSCH does not impose a slotframe
   size.  Depending on the application needs, these can range from 10's
   to 1000's of time slots.  The shorter the slotframe, the more often a
   time slot repeats, resulting in more available bandwidth, but also in
   a higher power consumption.

A.3.  Node TSCH Schedule

   A TSCH schedule instructs each node what to do in each time slot:
   transmit, receive, or sleep.  The schedule indicates, for each
   scheduled (transmit or receive) cell, a channelOffset and the address
   of the neighbor with which to communicate.









Watteyne, et al.              Informational                    [Page 15]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


   Once a node obtains its schedule, it executes it:

   o  For each transmit cell, the node checks whether there is a packet
      in the outgoing buffer that matches the neighbor written in the
      schedule information for that time slot.  If there is none, the
      node keeps its radio off for the duration of the time slot.  If
      there is one, the node can ask for the neighbor to acknowledge it,
      in which case it has to listen for the acknowledgment after
      transmitting.

   o  For each receive cell, the node listens for possible incoming
      packets.  If none is received after some listening period, it
      shuts down its radio.  If a packet is received, addressed to the
      node, and passes security checks, the node can send back an
      acknowledgment.

   How the schedule is built, updated, and maintained, and by which
   entity, is outside of the scope of the IEEE 802.15.4e standard.

A.4.  Cells and Bundles

   Assuming the schedule is well built, if node A is scheduled to
   transmit to node B at slotOffset 5 and channelOffset 11, node B will
   be scheduled to receive from node A at the same slotOffset and
   channelOffset.

   A single element of the schedule characterized by a slotOffset and
   channelOffset, and reserved for node A to transmit to node B (or for
   node B to receive from node A) within a given slotframe, is called a
   "scheduled cell".

   If there is a lot of data flowing from node A to node B, the schedule
   might contain multiple cells from A to B, at different times.
   Multiple cells scheduled to the same neighbor can be equivalent,
   i.e., the MAC layer sends the packet on whichever of these cells
   shows up first after the packet was put in the MAC queue.  The union
   of all cells between two neighbors, A and B, is called a "bundle".
   Since the slotframe repeats over time (and the length of the
   slotframe is typically constant), each cell gives a "quantum" of
   bandwidth to a given neighbor.  Modifying the number of equivalent
   cells in a bundle modifies the amount of resources allocated between
   two neighbors.









Watteyne, et al.              Informational                    [Page 16]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


A.5.  Dedicated vs. Shared Cells

   By default, each scheduled transmit cell within the TSCH schedule is
   dedicated, i.e., reserved only for node A to transmit to node B.
   IEEE 802.15.4e also allows a cell to be marked as shared.  In a
   shared cell, multiple nodes can transmit at the same time, on the
   same frequency.  To avoid contention, TSCH defines a backoff
   algorithm for shared cells.

   A scheduled cell can be marked as both transmitting and receiving.
   In this case, a node transmits if it has an appropriate packet in its
   output buffer, or listens otherwise.  Marking a cell as
   [transmit,receive,shared] results in slotted-Aloha behavior.

A.6.  Absolute Slot Number

   TSCH defines a timeslot counter called Absolute Slot Number (ASN).
   When a new network is created, the ASN is initialized to 0; from then
   on, it increments by 1 at each timeslot.  In detail:

   ASN = (k*S+t)

   where k is the slotframe cycle (i.e., the number of slotframe
   repetitions since the network was started), S the slotframe size, and
   t the slotOffset.  A node learns the current ASN when it joins the
   network.  Since nodes are synchronized, they all know the current
   value of the ASN, at any time.  The ASN is encoded as a 5-byte
   number: this allows it to increment for hundreds of years (the exact
   value depends on the duration of a timeslot) without wrapping over.
   The ASN is used to calculate the frequency to communicate on and can
   be used for security-related operations.

A.7.  Channel Hopping

   For each scheduled cell, the schedule specifies a slotOffset and a
   channelOffset.  In a well-built schedule, when node A has a transmit
   cell to node B on channelOffset 5, node B has a receive cell from
   node A on the same channelOffset.  The channelOffset is translated by
   both nodes into a frequency using the following function:

   frequency = F {(ASN + channelOffset) mod nFreq}

   The function F consists of a lookup table containing the set of
   available channels.  The value nFreq (the number of available
   frequencies) is the size of this lookup table.  There are as many
   channelOffset values as there are frequencies available (e.g., 16
   when using radios that are compliant with IEEE 802.15.4 at 2.4 GHz,
   when all channels are used).  Since both nodes have the same



Watteyne, et al.              Informational                    [Page 17]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


   channelOffset written in their schedule for that scheduled cell, and
   the same ASN counter, they compute the same frequency.  At the next
   iteration (cycle) of the slotframe, however, while the channelOffset
   is the same, the ASN has changed, resulting in the computation of a
   different frequency.

   This results in "channel hopping": even with a static schedule, pairs
   of neighbors "hop" between the different frequencies when
   communicating.  A way of ensuring communication happens on all
   available frequencies is to set the number of timeslots in a
   slotframe to a prime number.  Channel hopping is a technique known to
   efficiently combat multi-path fading and external interference
   [Watteyne09reliability].

A.8.  Time Synchronization

   Because of the slotted nature of communication in a TSCH network,
   nodes have to maintain tight synchronization.  All nodes are assumed
   to be equipped with clocks to keep track of time.  Yet, because
   clocks in different nodes drift with respect to one another, neighbor
   nodes need to periodically resynchronize.

   Each node needs to periodically synchronize its network clock to
   another node, and it also provides its network time to its neighbors.
   It is up to the entity that manages the schedule to assign an
   adequate time source neighbor to each node, i.e., to indicate in the
   schedule which neighbor is its "time source neighbor".  While setting
   the time source neighbor, it is important to avoid synchronization
   loops, which could result in the formation of independent clusters of
   synchronized nodes.

   TSCH adds timing information in all packets that are exchanged (both
   data and ACK frames).  This means that neighbor nodes can
   resynchronize to one another whenever they exchange data.  In detail,
   two methods are defined in IEEE 802.15.4e (of 2012) for allowing a
   device to synchronize in a TSCH network: (i) Acknowledgment-based and
   (ii) Frame-based synchronization.  In both cases, the receiver
   calculates the difference in time between the expected time of frame
   arrival and its actual arrival.  In Acknowledgment-based
   synchronization, the receiver provides such information to the sender
   node in its acknowledgment.  In this case, it is the sender node that
   synchronizes to the clock of the receiver.  In Frame-based
   synchronization, the receiver uses the computed delta for adjusting
   its own clock.  In this case, it is the receiver node that
   synchronizes to the clock of the sender.






Watteyne, et al.              Informational                    [Page 18]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


   Different synchronization policies are possible.  Nodes can keep
   synchronization exclusively by exchanging EBs.  Nodes can also keep
   synchronized by periodically sending valid frames to a time source
   neighbor and use the acknowledgment to resynchronize.  Both methods
   (or a combination thereof) are valid synchronization policies; which
   one to use depends on network requirements.

A.9.  Power Consumption

   There are only a handful of activities a node can perform during a
   timeslot: transmit, receive, or sleep.  Each of these operations has
   some energy cost associated to them; the exact value depends on the
   hardware used.  Given the schedule of a node, it is straightforward
   to calculate the expected average power consumption of that node.

A.10.  Network TSCH Schedule

   The schedule entirely defines the synchronization and communication
   between nodes.  By adding/removing cells between neighbors, one can
   adapt a schedule to the needs of the application.  Intuitive examples
   are:

   o  Make the schedule "sparse" for applications where nodes need to
      consume as little energy as possible, at the price of reduced
      bandwidth.

   o  Make the schedule "dense" for applications where nodes generate a
      lot of data, at the price of increased power consumption.

   o  Add more cells along a multi-hop route over which many packets
      flow.

A.11.  Join Process

   Nodes already part of the network can periodically send EB frames to
   announce the presence of the network.  These contain information
   about the size of the timeslot used in the network, the current ASN,
   information about the slotframes and timeslots the beaconing node is
   listening on, and a 1-byte join priority.  The join priority field
   gives information to make a better decision of which node to join.
   Even if a node is configured to send all EB frames on the same
   channelOffset, because of the channel hopping nature of TSCH
   described in Appendix A.7, this channelOffset translates into a
   different frequency at different slotframe cycles.  As a result, EB
   frames are sent on all frequencies.






Watteyne, et al.              Informational                    [Page 19]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


   A node wishing to join the network listens for EBs.  Since EBs are
   sent on all frequencies, the joining node can listen on any frequency
   until it hears an EB.  What frequency it listens on is implementation
   specific.  Once it has received one or more EBs, the new node enables
   the TSCH mode and uses the ASN and the other timing information from
   the EB to synchronize to the network.  Using the slotframe and cell
   information from the EB, it knows how to contact other nodes in the
   network.

   The IEEE 802.15.4e TSCH standard does not define the steps beyond
   this network "bootstrap".

A.12.  Information Elements

   TSCH introduces the concept of Information Elements (IEs).  An IE is
   a list of Type-Length-Value containers placed at the end of the MAC
   header.  A small number of types are defined for TSCH (e.g., the ASN
   in the EB is contained in an IE), and an unmanaged range is available
   for extensions.

   A data bit in the MAC header indicates whether the frame contains
   IEs.  IEs are grouped into Header IEs, consumed by the MAC layer and
   therefore typically invisible to the next higher layer, and Payload
   IEs, which are passed untouched to the next higher layer, possibly
   followed by regular payload.  Payload IEs can therefore be used for
   the next higher layers of two neighbor nodes to exchange information.

A.13.  Extensibility

   The TSCH standard is designed to be extensible.  It introduces the
   mechanisms as "building block" (e.g., cells, bundles, slotframes,
   etc.), but leaves entire freedom to the upper layer to assemble
   those.  The MAC protocol can be extended by defining new Header IEs.
   An intermediate layer can be defined to manage the MAC layer by
   defining new Payload IEs.
















Watteyne, et al.              Informational                    [Page 20]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


Appendix B.  TSCH Features

   This section details features of TSCH, which might be interesting for
   the work of the 6TiSCH WG.  It does not define any requirements.

B.1.  Collision-Free Communication

   TSCH allows one to design a schedule that yields collision-free
   communication.  This is done by building the schedule with dedicated
   cells in such a way that at most, one node communicates with a
   specific neighbor in each slotOffset/channelOffset cell.  Multiple
   pairs of neighbor nodes can exchange data at the same time, but on
   different frequencies.

B.2.  Multi-Channel vs. Channel Hopping

   A TSCH schedule looks like a matrix of width "slotframe size", S, and
   of height "number of frequencies", nFreq.  For a scheduling
   algorithm, cells can be considered atomic "units" to schedule.  In
   particular, because of the channel hopping nature of TSCH, the
   scheduling algorithm should not worry about the actual frequency
   communication happens on, since it changes at each slotframe
   iteration.

B.3.  Cost of (Continuous) Synchronization

   When there is traffic in the network, nodes that are communicating
   implicitly resynchronize using the data frames they exchange.  In the
   absence of data traffic, nodes are required to synchronize to their
   time source neighbor(s) periodically not to drift in time.  If they
   have not been communicating for some time (typically 30 s), nodes can
   exchange a dummy data frame to resynchronize.  The frequency at which
   such messages need to be transmitted depends on the stability of the
   clock source and on how "early" each node starts listening for data
   (the "guard time").  Theoretically, with a 10 ppm clock and a 1 ms
   guard time, this period can be 100 s.  Assuming this exchange causes
   the node's radio to be on for 5 ms, this yields a radio duty cycle
   needed to keep synchronized of 5 ms / 100 s = 0.005%.  While TSCH
   does require nodes to resynchronize periodically, the cost of doing
   so is very low.

B.4.  Topology Stability

   The channel hopping nature of TSCH causes links to be very "stable".
   Wireless phenomena such as multi-path fading and external
   interference impact a wireless link between two nodes differently on
   each frequency.  If a transmission from node A to node B fails,
   retransmitting on a different frequency has a higher likelihood of



Watteyne, et al.              Informational                    [Page 21]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


   succeeding that retransmitting on the same frequency.  As a result,
   even when some frequencies are "behaving bad", channel hopping
   "smoothens" the contribution of each frequency, resulting in more
   stable links and therefore a more stable topology.

B.5.  Multiple Concurrent Slotframes

   The TSCH standard allows for multiple slotframes to coexist in a
   node's schedule.  It is possible that, at some timeslot, a node has
   multiple activities scheduled (e.g., transmit to node B on slotframe
   2, receive from node C on slotframe 1).  To handle this situation,
   the TSCH standard defines the following precedence rules:

   1.  Transmissions take precedence over receptions;

   2.  Lower slotframe identifiers take precedence over higher slotframe
       identifiers.

   In the example above, the node would transmit to node B on slotframe
   2.

Acknowledgments

   Special thanks to Dominique Barthel, Patricia Brett, Guillaume
   Gaillard, Pat Kinney, Ines Robles, Timothy J.  Salo, Jonathan Simon,
   Rene Struik, and Xavi Vilajosana for reviewing the document and
   providing valuable feedback.  Thanks to the IoT6 European Project
   (STREP) of the 7th Framework Program (Grant 288445).























Watteyne, et al.              Informational                    [Page 22]
^L
RFC 7554                       6TiSCH-TSCH                      May 2015


Authors' Addresses

   Thomas Watteyne (editor)
   Linear Technology
   32990 Alvarado-Niles Road, Suite 910
   Union City, CA  94587
   United States

   Phone: +1 (510) 400-2978
   EMail: twatteyne@linear.com


   Maria Rita Palattella
   University of Luxembourg
   Interdisciplinary Centre for Security, Reliability and Trust
   4, rue Alphonse Weicker
   Luxembourg  L-2721
   Luxembourg

   Phone: +352 46 66 44 5841
   EMail: maria-rita.palattella@uni.lu


   Luigi Alfredo Grieco
   Politecnico di Bari
   Department of Electrical and Information Engineering
   Via Orabona 4
   Bari  70125
   Italy

   Phone: +39 08 05 96 3911
   EMail: a.grieco@poliba.it



















Watteyne, et al.              Informational                    [Page 23]
^L