diff options
| author | Thomas Voss <mail@thomasvoss.com> | 2024-11-27 20:54:24 +0100 |
|---|---|---|
| committer | Thomas Voss <mail@thomasvoss.com> | 2024-11-27 20:54:24 +0100 |
| commit | 4bfd864f10b68b71482b35c818559068ef8d5797 (patch) | |
| tree | e3989f47a7994642eb325063d46e8f08ffa681dc /doc/rfc/rfc4717.txt | |
| parent | ea76e11061bda059ae9f9ad130a9895cc85607db (diff) | |
doc: Add RFC documents
Diffstat (limited to 'doc/rfc/rfc4717.txt')
| -rw-r--r-- | doc/rfc/rfc4717.txt | 2243 |
1 files changed, 2243 insertions, 0 deletions
diff --git a/doc/rfc/rfc4717.txt b/doc/rfc/rfc4717.txt new file mode 100644 index 0000000..7b29e46 --- /dev/null +++ b/doc/rfc/rfc4717.txt @@ -0,0 +1,2243 @@ + + + + + + +Network Working Group L. Martini +Request for Comments: 4717 J. Jayakumar +Category: Standards Track Cisco Systems, Inc. + M. Bocci + Alcatel + N. El-Aawar + Level 3 Communications, LLC + J. Brayley + ECI Telecom Inc. + G. Koleyni + Nortel Networks + December 2006 + + + Encapsulation Methods for Transport of + Asynchronous Transfer Mode (ATM) over MPLS Networks + +Status of This Memo + + This document specifies an Internet standards track protocol for the + Internet community, and requests discussion and suggestions for + improvements. Please refer to the current edition of the "Internet + Official Protocol Standards" (STD 1) for the standardization state + and status of this protocol. Distribution of this memo is unlimited. + +Copyright Notice + + Copyright (C) The IETF Trust (2006). + +Abstract + + An Asynchronous Transfer Mode (ATM) Pseudowire (PW) is used to carry + ATM cells over an MPLS network. This enables service providers to + offer "emulated" ATM services over existing MPLS networks. This + document specifies methods for the encapsulation of ATM cells within + a pseudowire. It also specifies the procedures for using a PW to + provide an ATM service. + + + + + + + + + + + + + + +Martini, et al. Standards Track [Page 1] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + +Table of Contents + + 1. Introduction ....................................................3 + 2. Specification of Requirements ...................................4 + 3. Applicability Statement .........................................4 + 4. Terminology .....................................................4 + 5. General Encapsulation Method ....................................6 + 5.1. The Control Word ...........................................6 + 5.1.1. The Generic Control Word ............................7 + 5.1.2. The Preferred Control Word ..........................8 + 5.1.3. Setting the Sequence Number Field in the + Control Word ........................................9 + 5.2. MTU Requirements ...........................................9 + 5.3. MPLS Shim S Bit Value .....................................10 + 5.4. MPLS Shim TTL Values ......................................10 + 6. Encapsulation Mode Applicability ...............................10 + 6.1. ATM N-to-One Cell Mode ....................................11 + 6.2. ATM One-to-One Cell Encapsulation .........................13 + 6.3. AAL5 SDU Frame Encapsulation ..............................13 + 6.4. AAL5 PDU Frame Encapsulation ..............................14 + 7. ATM OAM Cell Support ...........................................15 + 7.1. VCC Case ..................................................15 + 7.2. VPC Case ..................................................16 + 7.3. SDU/PDU OAM Cell Emulation Mode ...........................16 + 7.4. Defect Handling ...........................................17 + 8. ATM N-to-One Cell Mode .........................................18 + 8.1. ATM N-to-One Service Encapsulation ........................19 + 9. ATM One-to-One Cell Mode .......................................21 + 9.1. ATM One-to-One Service Encapsulation ......................21 + 9.2. Sequence Number ...........................................22 + 9.3. ATM VCC Cell Transport Service ............................22 + 9.4. ATM VPC Services ..........................................24 + 9.4.1. ATM VPC Cell Transport Services ....................25 + 10. ATM AAL5 CPCS-SDU Mode ........................................26 + 10.1. Transparent AAL5 SDU Frame Encapsulation .................27 + 11. AAL5 PDU Frame Mode ...........................................28 + 11.1. Transparent AAL5 PDU Frame Encapsulation .................28 + 11.2. Fragmentation ............................................30 + 11.2.1. Procedures in the ATM-to-PSN Direction ............30 + 11.2.2. Procedures in the PSN-to-ATM Direction ............31 + 12. Mapping of ATM and PSN Classes of Service .....................31 + 13. ILMI Support ..................................................32 + 14. ATM-Specific Interface Parameter Sub-TLVs .....................32 + 15. Congestion Control ............................................32 + 16. Security Considerations .......................................33 + 17. Normative References ..........................................34 + 18. Informative References ........................................34 + 19. Significant Contributors ......................................36 + + + +Martini, et al. Standards Track [Page 2] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + +1. Introduction + + Packet Switched Networks (PSNs) have the potential to reduce the + complexity of a service provider's infrastructure by allowing + virtually any existing digital service to be supported over a single + networking infrastructure. The benefit of this model to a service + provider is threefold: + + -i. Leveraging of the existing systems and services to provide + increased capacity from a packet-switched core. + + -ii. Preserving existing network operational processes and + procedures used to maintain the legacy services. + + -iii. Using the common packet-switched network infrastructure to + support both the core capacity requirements of existing + services and the requirements of new services supported + natively over the packet-switched network. + + This document describes a method to carry ATM services over MPLS. It + lists ATM-specific requirements and provides encapsulation formats + and semantics for connecting ATM edge networks through a packet- + switched network using MPLS. + + Figure 1, below, displays the ATM services reference model. This + model is adapted from [RFC3985]. + + |<----- Pseudowire ----->| + | | + | |<-- PSN Tunnel -->| | + ATM Service V V V V ATM Service + | +----+ +----+ | + +----+ | | PE1|==================| PE2| | +----+ + | |----------|............PW1.............|----------| | + | CE1| | | | | | | |CE2 | + | |----------|............PW2.............|----------| | + +----+ | | |==================| | | +----+ + ^ +----+ +----+ | ^ + | Provider Edge 1 Provider Edge 2 | + | | + |<-------------- Emulated Service ---------------->| + Customer Customer + Edge 1 Edge 2 + + Figure 1: ATM Service Reference Model + + + + + + +Martini, et al. Standards Track [Page 3] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + +2. Specification of Requirements + + The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", + "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this + document are to be interpreted as described in [RFC2119]. + +3. Applicability Statement + + The ATM over PW service is not intended to perfectly emulate a + traditional ATM service, but it can be used for applications that + need an ATM transport service. + + The following are notable differences between traditional ATM service + and the protocol described in this document: + + - ATM cell ordering can be preserved using the OPTIONAL sequence + field in the control word; however, implementations are not + required to support this feature. The use of this feature may + impact other ATM quality of service (QoS) commitments. + + - The QoS model for traditional ATM can be emulated. However, the + detailed specification of ATM QoS emulation is outside the scope + of this document. The emulation must be able to provide the + required ATM QoS commitments for the end-user application. + + - The ATM flow control mechanisms are transparent to the MPLS + network and cannot reflect the status of the MPLS network. + + - Control plane support for ATM SVCs, SVPs, SPVCs, and SPVPs is + outside the scope of this document. + + Note that the encapsulations described in this specification are + identical to those described in [Y.1411] and [Y.1412]. + +4. Terminology + + One-to-one mode: specifies an encapsulation method that maps one ATM + Virtual Channel Connection (VCC) (or one ATM Virtual Path Connection + (VPC)) to one pseudowire. + + N-to-one mode (N >= 1): specifies an encapsulation method that maps + one or more ATM VCCs (or one or more ATM VPCs) to one pseudowire. + + Packet-Switched Network (PSN): an IP or MPLS network. + + Pseudowire Emulation Edge to Edge (PWE3): a mechanism that emulates + the essential attributes of a service (such as a T1 leased line or + Frame Relay) over a PSN. + + + +Martini, et al. Standards Track [Page 4] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + Customer Edge (CE): a device where one end of a service originates + and/or terminates. The CE is not aware that it is using an emulated + service rather than a native service. + + Provider Edge (PE): a device that provides PWE3 to a CE. + + Pseudowire (PW): a connection between two PEs carried over a PSN. + The PE provides the adaptation between the CE and the PW. + + Pseudowire PDU: a PDU sent on the PW that contains all of the data + and control information necessary to provide the desired service. + + PSN Tunnel: a tunnel inside which multiple PWs can be nested so that + they are transparent to core PSN devices. + + PSN Bound: the traffic direction where information from a CE is + adapted to a PW, and PW-PDUs are sent into the PSN. + + CE Bound: the traffic direction where PW-PDUs are received on a PW + from the PSN, re-converted back in the emulated service, and sent out + to a CE. + + Ingress: the point where the ATM service is encapsulated into a + pseudowire PDU (ATM to PSN direction). + + Egress: the point where the ATM service is decapsulated from a + pseudowire PDU (PSN to ATM direction). + + CTD: Cell Transfer Delay. + + MTU: Maximum Transmission Unit. + + SDU: Service Data Unit. + + OAM: Operations And Maintenance. + + PVC: Permanent Virtual Connection. An ATM connection that is + provisioned via a network management interface. The connection is + not signaled. + + VCC: Virtual Circuit Connection. An ATM connection that is switched + based on the cell header's VCI. + + VPC: Virtual Path Connection. An ATM connection that is switched + based on the cell header's VPI. + + Additional terminology relevant to pseudowires and Layer 2 Virtual + Private Networking (L2VPN) in general may be found in [RFC4026]. + + + +Martini, et al. Standards Track [Page 5] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + +5. General Encapsulation Method + + This section describes the general encapsulation format for ATM over + PSN pseudowires. + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | PSN Transport Header (As Required) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Pseudowire Header | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | ATM Control Word | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | ATM Service Payload | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + Figure 2: General format for ATM encapsulation over PSNs + + The PSN Transport Header depends on the particular tunneling + technology in use. This header is used to transport the encapsulated + ATM information through the packet-switched core. + + The Pseudowire Header identifies a particular ATM service on a + tunnel. In case of MPLS, the pseudowire header is one or more MPLS + labels at the bottom of the MPLS label stack. + + The ATM Control Word is inserted before the ATM service payload. It + may contain a length and sequence number in addition to certain + control bits needed to carry the service. + +5.1. The Control Word + + The Control Words defined in this section are based on the Generic PW + MPLS Control Word as defined in [RFC4385]. They provide the ability + to sequence individual frames on the PW, avoidance of equal-cost + multiple-path load-balancing (ECMP) [RFC2992], and OAM mechanisms + including VCCV [VCCV]. + + [RFC4385] states, "If a PW is sensitive to packet misordering and is + being carried over an MPLS PSN that uses the contents of the MPLS + payload to select the ECMP path, it MUST employ a mechanism which + prevents packet misordering." This is necessary because ECMP + implementations may examine the first nibble after the MPLS label + stack to determine whether or not the labelled packet is IP. Thus, + if the VPI of an ATM connection carried over the PW using N-to-one + cell mode encapsulation, without a control word present, begins with + 0x4 or 0x6, it could be mistaken for an IPv4 or IPv6 packet. This + + + +Martini, et al. Standards Track [Page 6] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + could, depending on the configuration and topology of the MPLS + network, lead to a situation where all packets for a given PW do not + follow the same path. This may increase out-of-order frames on a + given PW, or cause OAM packets to follow a different path than actual + traffic (see section 4.4.3 on Frame Ordering). + + The features that the control word provides may not be needed for a + given ATM PW. For example, ECMP may not be present or active on a + given MPLS network, strict frame sequencing may not be required, etc. + If this is the case, and the control word is not REQUIRED by the + encapsulation mode for other functions (such as length or the + transport of ATM protocol specific information), the control word + provides little value and is therefore OPTIONAL. Early ATM PW + implementations have been deployed that do not include a control word + or the ability to process one if present. To aid in backwards + compatibility, future implementations MUST be able to send and + receive frames without a control word present. + + In all cases, the egress PE MUST be aware of whether the ingress PE + will send a control word over a specific PW. This may be achieved by + configuration of the PEs, or by signaling, as defined in [RFC4447]. + + If the pseudowire traverses a network link that requires a minimum + frame size (Ethernet is a practical example), with a minimum frame + size of 64 octets, then such links will apply padding to the + pseudowire PDU to reach its minimum frame size. In this case, the + control word must include a length field set to the PDU length. A + mechanism is required for the egress PE to detect and remove such + padding. + +5.1.1. The Generic Control Word + + This control word is used in the following encapsulation modes: + + - ATM One-to-one Cell Mode + - AAL5 PDU Frame Mode + + The PWE3 control word document [RFC4385] provides the following + structure for the generic control word: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |0 0 0 0| Specified by PW Encapsulation | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + + + + + +Martini, et al. Standards Track [Page 7] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + The detailed structure for the ATM One-to-one Cell Mode and for the + AAL5 PDU Frame Mode is as follows: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |0 0 0 0| Resvd | Sequence Number | ATM Specific | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + In the above diagram, the first 4 bits MUST be set to 0 to indicate + PW data. They MUST be ignored by the receiving PE. + + The next four bits are reserved and MUST be set to 0 upon + transmission and ignored upon reception. + + The next 16 bits provide a sequence number that can be used to + guarantee ordered packet delivery. The processing of the sequence + number field is OPTIONAL. + + The sequence number space is a 16-bit, unsigned circular space. The + sequence number value 0 is used to indicate that the sequence number + check algorithm is not used. + + The last 8 bits provide space for carrying ATM-specific flags. These + are defined in the protocol-specific details below. + + There is no requirement for a length field for the One-to-one Cell + and PDU Frame modes because the PSN PDU is always greater than 64 + bytes; therefore, no padding is applied in Ethernet links in the PSN. + +5.1.2. The Preferred Control Word + + This control word is used in the following encapsulation modes: + + - ATM N-to-one Cell Mode + - AAL5 SDU Frame Mode + + It is defined as follows: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |0 0 0 0| Flags |Res| Length | Sequence Number | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + In the above diagram, the first 4 bits MUST be set to 0 to indicate + PW data. They MUST be ignored by the receiving PE. + + + + +Martini, et al. Standards Track [Page 8] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + The next 4 bits provide space for carrying protocol-specific flags. + These are defined in the protocol-specific details below. + + The next 6 bits provide a length field, which is used as follows: If + the packet's length (defined as the length of the layer 2 payload + plus the length of the control word) is less than 64 bytes, the + length field MUST be set to the packet's length. Otherwise, the + length field MUST be set to zero. The value of the length field, if + non-zero, can be used to remove any padding. When the packet reaches + the service provider's egress router, it may be desirable to remove + the padding before forwarding the packet. Note that the length field + is not used in the N-to-one mode and MUST be set to 0. + + The last 16 bits provide a sequence number that can be used to + guarantee ordered packet delivery. The processing of the sequence + number field is OPTIONAL. + + The sequence number space is a 16-bit, unsigned circular space. The + sequence number value 0 is used to indicate that the sequence number + check algorithm is not used. + +5.1.3. Setting the Sequence Number Field in the Control Word + + This section applies to the sequence number field of both the Generic + and Preferred Control Words. + + For a given emulated VC and a pair of routers PE1 and PE2, if PE1 + supports packet sequencing, then the sequencing procedures defined in + [RFC4385] MUST be used. + + Packets that are received out of order MAY be dropped or reordered at + the discretion of the receiver. + + A simple extension of the processing algorithm in [RFC4385] MAY be + used to detect lost packets. + + If a PE router negotiated not to use receive sequence number + processing, and it received a non-zero sequence number, then it + SHOULD send a PW status message indicating a receive fault and + disable the PW. + +5.2. MTU Requirements + + The network MUST be configured with an MTU that is sufficient to + transport the largest encapsulation frames. If MPLS is used as the + tunneling protocol, for example, this is likely to be 12 or more + bytes greater than the largest frame size. Other tunneling protocols + may have longer headers and require larger MTUs. If the ingress + + + +Martini, et al. Standards Track [Page 9] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + router determines that an encapsulated layer 2 PDU exceeds the MTU of + the tunnel through which it must be sent, the PDU MUST be dropped. + If an egress router receives an encapsulated layer 2 PDU whose + payload length (i.e., the length of the PDU itself without any of the + encapsulation headers) exceeds the MTU of the destination layer 2 + interface, the PDU MUST be dropped. + +5.3. MPLS Shim S Bit Value + + The ingress label switching router (LSR), PE1, MUST set the S bit of + the PW label to a value of 1 to denote that the VC label is at the + bottom of the stack. For more information on setting the S Bit, see + [RFC3032]. + +5.4. MPLS Shim TTL Values + + The setting of the TTL value in the PW label is application + dependent. In any case, [RFC3032] TTL processing procedure, + including handling of expired TTLs, MUST be followed. + +6. Encapsulation Mode Applicability + + This document defines two methods for encapsulation of ATM cells, + namely, One-to-one mode and N-to-one mode. + + The N-to-one mode (N >= 1) specifies an encapsulation method that + maps one or more ATM VCCs (or one or more ATM VPCs) to one + pseudowire. This is the only REQUIRED mode. One format is used for + both the VCC or VPC mapping to the tunnel. The 4-octet ATM header is + unaltered in the encapsulation; thus, the VPI/VCI is always present. + Cells from one or more VCCs (or one or more VPCs) may be + concatenated. + + The One-to-one mode specifies an encapsulation method that maps one + ATM VCC or one ATM VPC to one pseudowire. For VCCs, the VPI/VCI is + not included. For VPCs, the VPI is not included. Cells from one VCC + or one VPC may be concatenated. This mode is OPTIONAL. + + Furthermore, different OPTIONAL encapsulations are supported for ATM + AAL5 transport: one for ATM AAL5 SDUs, and another for ATM AAL5 PDUs. + + Three deployment models are supported by the encapsulations described + in this document: + + -i. Single ATM Connection: A PW carries the cells of only one + ATM VCC or VPC. This supports both the transport of + multiservice ATM and L2VPN service over a PSN for all AAL + types. + + + +Martini, et al. Standards Track [Page 10] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + -ii. Multiple ATM Connections: A PW carries the cells of multiple + ATM VCCs and/or VPCs. This also supports both the transport + of multiservice ATM and L2VPN service over a PSN for all AAL + types. + + -iii. AAL5: A PW carries the AAL5 frames of only one ATM VCC. A + large proportion of the data carried on ATM networks is + frame based and therefore uses AAL5. The AAL5 mapping takes + advantage of the delineation of higher-layer frames in the + ATM layer to provide increased bandwidth efficiency compared + with the basic cell mapping. The nature of the service, as + defined by the ATM service category [TM4.0] or the ATM + transfer capability [I.371], should be preserved. + +6.1. ATM N-to-One Cell Mode + + This encapsulation supports both the Single and Multiple ATM + Connection deployment models. This encapsulation is REQUIRED. + + The encapsulation allows multiple VCCs/VPCs to be carried within a + single pseudowire. However, a service provider may wish to provision + a single VCC to a pseudowire in order to satisfy QoS or restoration + requirements. + + The encapsulation also supports the binding of multiple VCCs/VPCs to + a single pseudowire. This capability is useful in order to make more + efficient use of the PW demultiplexing header space as well as to + ease provisioning of the VCC/VPC services. + + In the simplest case, this encapsulation can be used to transmit a + single ATM cell per PSN PDU. However, in order to provide better PSN + bandwidth efficiency, several ATM cells may optionally be + encapsulated in a single PSN PDU. This process is called cell + concatenation. + + The encapsulation has the following attributes: + + -i. Supports all ATM Adaptation Layer Types. + + -ii. Non-terminating OAM/Admin cells are transported among the + user cells in the same order as they are received. This + requirement enables the use of various performance + management and security applications. + + + + + + + + +Martini, et al. Standards Track [Page 11] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + -iii. In order to gain transport efficiency on the PSN, multiple + cells may be encapsulated in a single PW PDU. This process + is called cell concatenation. How many cells to insert or + how long to wait for cell arrival before sending a PW PDU is + an implementation decision. Cell concatenation adds latency + and delay variation to a cell relay service. + + -iv. The CLP bit from each cell may be mapped to a corresponding + marking on the PW PDU. This allows the drop precedence to + be preserved across the PSN. + + -v. If the Single ATM connection deployment model is used, then + it is simpler to provide an ATM layer service. The nature + of the service, as defined by the ATM service category + [TM4.0] or ATM transfer capability [I.371], should be + preserved. + + The limitations of the ATM N-to-one cell encapsulation are: + + -vi. There is no currently defined method to translate the + forward congestion indication (EFCI) to a corresponding + function in the PSN. Nor is there a way to translate PSN + congestion to the EFCI upon transmission by the egress PE. + + -vii. The ATM cell header checksum can detect a 2-bit error or + detect and correct a single-bit error in the cell header. + Analogous functionality does not exist in most PSNs. A + single bit error in a PW PDU will most likely cause the + packet to be dropped due to an L2 Frame Check Sequence (FCS) + failure. + + -viii. Cells can be concatenated from multiple VCCs or VPCs + belonging to different service categories and QoS + requirements. In this case, the PSN packet must receive + treatment by the PSN to support the highest QoS of the ATM + VCCs/VPCs carried. + + -ix. Cell encapsulation only supports point-to-point Label + Switched Paths (LSPs). Multipoint-to-point and point-to- + multi-point are for further study (FFS). + + -x. The number of concatenated ATM cells is limited by the MTU + size and the cell transfer delay (CTD) and cell delay + variation (CDV) objectives of multiple ATM connections that + are multiplexed into a single PW. + + + + + + +Martini, et al. Standards Track [Page 12] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + +6.2. ATM One-to-One Cell Encapsulation + + This OPTIONAL encapsulation supports the Single ATM Connection + deployment model. + + Like the N-to-one cell encapsulation mode, the One-to-one mode + supports cell concatenation. The advantage of this encapsulation is + that it utilizes less bandwidth that the N-to-one encapsulation, for + a given number of concatenated cells. Since only one ATM VCC or VPC + is carried on a PW, the VCI and/or VPI of the ATM VCC or VPC can be + derived from the context of the PW using the PW label. These fields + therefore do not need to be encapsulated for a VCC, and only the VCI + needs to be encapsulated for a VPC. This encapsulation thus allows + service providers to achieve a higher bandwidth efficiency on PSN + links than the N-to-one encapsulation for a given number of + concatenated cells. + + The limitations vi, vii, ix, and x of N-to-one mode apply. + +6.3. AAL5 SDU Frame Encapsulation + + This OPTIONAL encapsulation supports the AAL5 model. This mode + allows the transport of ATM AAL5 CSPS-SDUs traveling on a particular + ATM PVC across the network to another ATM PVC. This encapsulation is + used by a PW of type 0x0002 "ATM AAL5 SDU VCC transport" as allocated + in [RFC4446]. + + The AAL5 SDU encapsulation is more efficient for small AAL5 SDUs than + the VCC cell encapsulations. In turn, it presents a more efficient + alternative to the cell relay service when carrying [RFC2684]- + encapsulated IP PDUs across a PSN. + + The AAL5-SDU encapsulation requires Segmentation and Reassembly (SAR) + on the PE-CE ATM interface. This SAR function is provided by common + off-the-shelf hardware components. Once reassembled, the AAL5-SDU is + carried via a pseudowire to the egress PE. Herein lies another + advantage of the AAL5-SDU encapsulation. + + The limitations of the AAL5 SDU encapsulation are: + + -i. If an ATM OAM cell is received at the ingress PE, it is sent + before the cells of the surrounding AAL5 frame. Therefore, + OAM cell reordering may occur, which may cause certain ATM + OAM performance monitoring and ATM security applications to + operate incorrectly. + + + + + + +Martini, et al. Standards Track [Page 13] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + -ii. If the ALL5 PDU is scrambled using ATM security standards, a + PE will not be able to extract the ALL5 SDU, and therefore + the whole PDU will be dropped. + + -iii. The AAL5 PDU CRC is not transported across the PSN. The CRC + must therefore be regenerated at the egress PE since the CRC + has end-to-end significance in ATM security. This means + that the AAL5 CRC may not be used to accurately check for + errors on the end-to-end ATM VCC. + + -iv. The Length of AAL5 frame may exceed the MTU of the PSN. + This requires fragmentation, which may not be available to + all nodes at the PW endpoint. + + -v. This mode does not preserve the value of the CLP bit for + every ATM cell within an AAL5 PDU. Therefore, transparency + of the CLP setting may be violated. Additionally, tagging + of some cells may occur when tagging is not allowed by the + conformance definition [TM4.0]. + + -vi. This mode does not preserve the EFCI state for every ATM + cell within an AAL5 PDU. Therefore, transparency of the + EFCI state may be violated. + +6.4. AAL5 PDU Frame Encapsulation + + This OPTIONAL encapsulation supports the AAL5 model. + + The primary application supported by AAL5 PDU frame encapsulation + over PSN is the transparent carriage of ATM layer services that use + AAL5 to carry higher-layer frames. The main advantage of this AAL5 + mode is that it is transparent to ATM OAM and ATM security + applications. + + One important consideration is to allow OAM information to be treated + as in the original network. This encapsulation mode allows this + transparency while performing AAL5 frame encapsulation. This mode + supports fragmentation, which may be performed in order to maintain + the position of the OAM cells with respect to the user cells. + + Fragmentation may also be performed to maintain the size of the + packet carrying the AAL5 PDU within the MTU of the link. + Fragmentation provides a means for the PE to set the size of the PW + packet to a different value than that of the original AAL5 PDU. This + means that the PE has control on the delay and jitter provided to the + ATM cells. + + + + + +Martini, et al. Standards Track [Page 14] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + The whole AAL5-PDU is encapsulated. In this case, all necessary + parameters, such as CPCS-UU (CPCS User-to-User indicator), CPI + (Common Part Indicator), Length (Length of the CPCS-SDU) and CRC + (Cyclic Redundancy Check), are transported as part of the payload. + Note that carrying of the full PDU also allows the simplification of + the fragmentation operation since it is performed at cell boundaries + and the CRC in the trailer of the AAL5 PDU can be used to check the + integrity of the PDU. + + Reassembly is not required at the egress PE for the PSN-to-ATM + direction. + + The limitations v and vi of the AAL5 SDU mode apply to this mode as + well. + +7. ATM OAM Cell Support + +7.1. VCC Case + + In general, when configured for ATM VCC service, both PEs SHOULD act + as a VC switch, in accordance with the OAM procedures defined in + [I.610]. + + The PEs SHOULD be able to pass the following OAM cells transparently: + + - F5 Alarm Indication Signal (AIS) (segment and end-to-end) + - F5 Remote Defect Indicator (RDI) (segment and end-to-end) + - F5 loopback (segment and end-to-end) + - Resource Management + - Performance Management + - Continuity Check + - Security + + However, if configured to be an administrative segment boundary, the + PE SHOULD terminate and process F5 segment OAM cells. + + F4 OAM cells are inserted or extracted at the VP link termination. + These OAM cells are not seen at the VC link termination and are + therefore not sent across the PSN. + + When the PE is operating in AAL5 CPCS-SDU transport mode if it does + not support transport of ATM cells, the PE MUST discard incoming MPLS + frames on an ATM PW that contain a PW label with the T bit set. + + + + + + + + +Martini, et al. Standards Track [Page 15] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + +7.2. VPC Case + + When configured for a VPC cell relay service, both PEs SHOULD act as + a VP cross-connect in accordance with the OAM procedures defined in + [I.610]. + + The PEs SHOULD be able to process and pass the following OAM cells + transparently according to [I.610]: + + - F4 AIS (segment and end-to-end) + - F4 RDI (segment and end-to-end) + - F4 loopback (segment and end-to-end) + + However, if configured to be an administrative segment boundary, the + PE SHOULD terminate and process F4 segment OAM cells. + + F5 OAM are not inserted or extracted here. The PEs MUST be able to + pass the following OAM cells transparently: + + - F5 AIS (segment and end-to-end) + - F5 RDI (segment and end-to-end) + - F5 loopback (segment and end-to-end) + - Resource Management + - Performance Management + - Continuity Check + - Security + + The OAM cell MAY be encapsulated together with other user data cells + if multiple cell encapsulation is used. + +7.3. SDU/PDU OAM Cell Emulation Mode + + A PE operating in ATM SDU or PDU transport mode that does not support + transport of OAM cells across a PW MAY provide OAM support on ATM + PVCs using the following procedures: + + - Loopback cells response + + If an F5 end-to-end OAM cell is received from an ATM VC, by + either PE that is transporting this ATM VC, with a loopback + indication value of 1, and the PE has a label mapping for the ATM + VC, then the PE MUST decrement the loopback indication value and + loop back the cell on the ATM VC. Otherwise, the loopback cell + MUST be discarded by the PE. + + + + + + + +Martini, et al. Standards Track [Page 16] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + - AIS alarm + + If an ingress PE, PE1, receives an AIS F4/F5 OAM cell, it MUST + notify the remote PE of the failure. The remote PE, PE2, MUST in + turn send F5 OAM AIS cells on the respective PVCs. Note that if + the PE supports forwarding of OAM cells, then the received OAM + AIS alarm cells MUST be forwarded along the PW as well. + + - Interface failure + + If the PE detects a physical interface failure, or the interface + is administratively disabled, the PE MUST notify the remote PE + for all VCs associated with the failure. + + - PSN/PW failure detection + + If the PE detects a failure in the PW, by receiving a label + withdraw for a specific PW ID, or the targeted Label Distribution + Protocol (LDP) session fails, or a PW status TLV notification is + received, then a proper AIS F5 OAM cell MUST be generated for all + the affected ATM PVCs. The AIS OAM alarm will be generated on + the ATM output port of the PE that detected the failure. + +7.4. Defect Handling + + Figure 3 illustrates four possible locations for defects on the PWE3 + service: + + - (a) On the ATM connection from CE to PE + - (b) On the ATM side of the PW + - (c) On the PSN side of the PE + - (d) In the PSN + + +----+ +----+ + +----+ | PE1|==================| PE2| +----+ + | |---a------|b..c........PW1...d.........|----------| | + | CE1| | | | | |CE2 | + | |----------|............PW2.............|----------| | + +----+ | |==================| | +----+ + ^ +----+ +----+ ^ + | Provider Edge 1 Provider Edge 2 | + | | + |<-------------- Emulated Service ---------------->| + Customer Customer + Edge 1 Edge 2 + + Figure 3: Defect Locations + + + + +Martini, et al. Standards Track [Page 17] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + For failures at (a) or (b), in the VPC case, the ingress PE MUST be + able to generate an F4 AIS upon reception of a lower-layer defect + (such as LOS). In the VCC case, the ingress PE SHOULD be able to + generate an F5 AIS upon reception of a corresponding F4 AIS or + lower-layer defect (such as LOS). These messages are sent across the + PSN. + + For failures at (c) or (d), in the VCC case, the egress PE SHOULD be + able to generate an F5 AIS based on a PSN failure (such as a PSN + tunnel failure or LOS on the PSN port). In the VPC case, the egress + PE SHOULD be able to generate an F4 AIS based on a PSN failure (such + as a PSN tunnel failure or LOS on the PSN port). + + If the ingress PE cannot support the generation of OAM cells, it MAY + notify the egress PE using a pseudowire-specific maintenance + mechanism such as the PW status message defined in [RFC4447]. + Alternatively, for example, the ingress PE MAY withdraw the + pseudowire (PW label) label associated with the service. Upon + receiving such a notification, the egress PE SHOULD generate the + appropriate F4 AIS (for VPC) or F5 AIS (for VCC). + + If the PW in one direction fails, then the complete bidirectional + service is considered to have failed. + +8. ATM N-to-One Cell Mode + + The N-to-one mode (N >= 1) described in this document allows a + service provider to offer an ATM PVC- or SVC-based service across a + network. The encapsulation allows multiple ATM VCCs or VPCs to be + carried within a single PSN tunnel. A service provider may also use + N-to-one mode to provision either one VCC or one VPC on a tunnel. + This section defines the VCC and VPC cell relay services over a PSN + and their applicability. + + + + + + + + + + + + + + + + + + +Martini, et al. Standards Track [Page 18] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + +8.1. ATM N-to-One Service Encapsulation + + This section describes the general encapsulation format for ATM over + PSN pseudowires. + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | PSN Transport Header (As Required) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | pseudowire Header | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |0 0 0 0| Flags |Res| Length | Sequence Number | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | ATM Service Payload | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + Figure 4: General format for ATM encapsulation over PSNs + + The PSN Transport Header depends on the particular tunneling + technology in use. This header is used to transport the encapsulated + ATM information through the packet-switched core. + + The Pseudowire Header identifies a particular ATM service on a + tunnel. Non-ATM services may also be carried on the PSN tunnel. + + As shown above, in Figure 4, the ATM Control Word is inserted before + the ATM service payload. It may contain a length field and a + sequence number field in addition to certain control bits needed to + carry the service. + + The ATM Service Payload is specific to the service being offered via + the pseudowire. It is defined in the following sections. + + In this encapsulation mode, ATM cells are transported individually. + The encapsulation of a single ATM cell is the only REQUIRED + encapsulation for ATM. The encapsulation of more than one ATM cell + in a PSN frame is OPTIONAL. + + The ATM cell encapsulation consists of an OPTIONAL control word and + one or more ATM cells, each consisting of a 4-byte ATM cell header + and the 48-byte ATM cell payload. This ATM cell header is defined as + in the FAST encapsulation [FBATM] section 3.1.1, but without the + trailer byte. The length of each frame, without the encapsulation + headers, is a multiple of 52 bytes. The maximum number of ATM cells + that can be fitted in a frame, in this fashion, is limited only by + the network MTU and by the ability of the egress router to process + them. The ingress router MUST NOT send more cells than the egress + + + +Martini, et al. Standards Track [Page 19] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + router is willing to receive. The number of cells that the egress + router is willing to receive may either be configured in the ingress + router or be signaled, for example using the methods described later + in this document and in [RFC4447]. The number of cells encapsulated + in a particular frame can be inferred by the frame length. The + control word is OPTIONAL. If the control word is used, then the flag + and length bits in the control word are not used. These bits MUST be + set to 0 when transmitting, and MUST be ignored upon receipt. + + The EFCI and CLP bits are carried across the network in the ATM cell + header. The edge routers that implement this document MAY, when + either adding or removing the encapsulation described herein, change + the EFCI bit from zero to one in order to reflect congestion in the + network that is known to the edge router, and change the CLP bit from + zero to one in order to reflect marking from edge policing of the ATM + Sustained Cell Rate. The EFCI and CLP bits SHOULD NOT be changed + from one to zero. + + This diagram illustrates an encapsulation of two ATM cells: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Control word ( Optional ) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | VPI | VCI | PTI |C| + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | ATM Payload ( 48 bytes ) | + | " | + | " | + | " | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | VPI | VCI | PTI |C| + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | ATM Payload ( 48 bytes ) | + | " | + | " | + | " | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + Figure 5: Multiple Cell ATM Encapsulation + + * When multiple VCCs or VPCs are transported in one pseudowire, + VPI/VCI values MUST be unique. When the multiple VCCs or VPCs + are from different a physical transmission path, it may be + necessary to assign unique VPI/VCI values to the ATM connections. + If they are from the same physical transmission path, the VPI/VCI + values are unique. + + + +Martini, et al. Standards Track [Page 20] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + * VPI + + The ingress router MUST copy the VPI field from the incoming cell + into this field. For particular emulated VCs, the egress router + MAY generate a new VPI and ignore the VPI contained in this + field. + + * VCI + + The ingress router MUST copy the VCI field from the incoming ATM + cell header into this field. For particular emulated VCs, the + egress router MAY generate a new VCI. + + * PTI & CLP (C bit) + + The PTI and CLP fields are the PTI and CLP fields of the incoming + ATM cells. The cell headers of the cells within the packet are + the ATM headers (without Header Error Check (HEC) field) of the + incoming cell. + +9. ATM One-to-One Cell Mode + + The One-to-one mode described in this document allows a service + provider to offer an ATM PVC- or SVC-based service across a network. + The encapsulation allows one ATM VCC or VPC to be carried within a + single pseudowire. + +9.1. ATM One-to-One Service Encapsulation + + This section describes the general encapsulation format for ATM over + pseudowires on an MPLS PSN. Figure 6 provides a general format for + encapsulation of ATM cells into packets. + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | PSN Transport Header (As Required) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Pseudowire Header | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |0 0 0 0| Resvd | Optional Sequence Number | ATM Specific | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | ATM Service Payload | + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + Figure 6: General format for One-to-one mode encapsulation over PSNs + + + + +Martini, et al. Standards Track [Page 21] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + The MPLS PSN Transport Header depends on how the MPLS network is + configured. The Pseudowire Header identifies a particular ATM + service within the PSN tunnel created by the PSN Transport Header. + + This header is used to transport the encapsulated ATM information + through the packet-switched core. + + The generic control word is inserted after the Pseudowire Header. + The presence of the control word is REQUIRED. + + The ATM Specific Header is inserted before the ATM service payload. + The ATM Specific Header contains control bits needed to carry the + service. These are defined in the ATM service descriptions below. + The length of ATM Specific Header may not always be one octet. It + depends on the service type. + + The ATM payload octet group is the payload of the service that is + being encapsulated. + +9.2. Sequence Number + + The sequence number is not required for all services. + + Treatment of the sequence number is according to section 5.1.3. + +9.3. ATM VCC Cell Transport Service + + The VCC cell transport service is characterized by the mapping of a + single ATM VCC (VPI/VCI) to a pseudowire. This service is fully + transparent to the ATM Adaptation Layer. The VCC single cell + transport service is OPTIONAL. This service MUST use the following + encapsulation format: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | PSN Transport Header (As Required) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Pseudowire Header | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |0 0 0 0| Resvd | Optional Sequence Number |M|V|Res| PTI |C| + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | | + | ATM Cell Payload ( 48 bytes ) | + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + Figure 7: Single ATM VCC Cell Encapsulation + + + +Martini, et al. Standards Track [Page 22] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + * M (transport mode) bit + + Bit (M) of the control byte indicates whether the packet contains + an ATM cell or a frame payload. If set to 0, the packet contains + an ATM cell. If set to 1, the PDU contains an AAL5 payload. + + * V (VCI present) bit + + Bit (V) of the control byte indicates whether the VCI field is + present in the packet. If set to 1, the VCI field is present for + the cell. If set to 0, no VCI field is present. In the case of + a VCC, the VCI field is not required. For VPC, the VCI field is + required and is transmitted with each cell. + + * Reserved bits + + The reserved bits should be set to 0 at the transmitter and + ignored upon reception. + + * PTI Bits + + The 3-bit Payload Type Identifier (PTI) incorporates ATM Layer + PTI coding of the cell. These bits are set to the value of the + PTI of the encapsulated ATM cell. + + * C (CLP) Bit + + The Cell Loss Priority (CLP) field indicates CLP value of the + encapsulated cell. + + For increased transport efficiency, the ingress PE SHOULD be able to + encapsulate multiple ATM cells into a pseudowire PDU. The ingress + and egress PE MUST agree to a maximum number of cells in a single + pseudowire PDU. This agreement may be accomplished via a + pseudowire-specific signaling mechanism or via static configuration. + + When multiple cells are encapsulated in the same PSN packet, the + ATM-specific byte MUST be repeated for each cell. This means that 49 + bytes are used to encapsulate each 53 byte ATM cell. + + + + + + + + + + + + +Martini, et al. Standards Track [Page 23] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | PSN Transport Header (As Required) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Pseudowire Header | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |0 0 0 0| Resvd | Optional Sequence Number |M|V|Res| PTI |C| + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | | + | ATM Cell Payload ( 48 bytes ) | + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |M|V|Res| PTI |C| | + +-+-+-+-+-+-+-+-+ | + | ATM Cell Payload ( 48 bytes ) | + | | + | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | | + +-+-+-+-+-+-+-+-+ + + Figure 8: Multiple ATM VCC Cell Encapsulation + +9.4. ATM VPC Services + + The VPC service is defined by mapping a single VPC (VPI) to a + pseudowire. As such, it emulates a Virtual Path cross-connect across + the PSN. All VCCs belonging to the VPC are carried transparently by + the VPC service. + + The egress PE may choose to apply a different VPI other than the one + that arrived at the ingress PE. The egress PE MUST choose the + outgoing VPI based solely upon the pseudowire header. As a VPC + service, the egress PE MUST NOT change the VCI field. + + + + + + + + + + + + + + + + + +Martini, et al. Standards Track [Page 24] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + +9.4.1. ATM VPC Cell Transport Services + + The ATM VPC cell transport service is OPTIONAL. + + This service MUST use the following cell mode encapsulation: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | PSN Transport Header (As Required) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Pseudowire Header | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |0 0 0 0| Resvd | Optional Sequence Number |M|V|Res| PTI |C| + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | VCI | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | + | | + | ATM Cell Payload ( 48 bytes ) | + | | + | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + Figure 9: Single Cell VPC Encapsulation + + The ATM control byte contains the same information as in the VCC + encapsulation except for the VCI field. + + * VCI Bits + + The 16-bit Virtual Circuit Identifier (VCI) incorporates ATM + Layer VCI value of the cell. + + For increased transport efficiency, the ingress PE SHOULD be able to + encapsulate multiple ATM cells into a pseudowire PDU. The ingress + and egress PE MUST agree to a maximum number of cells in a single + pseudowire PDU. This agreement may be accomplished via a + pseudowire-specific signaling mechanism or via static configuration. + + If the Egress PE supports cell concatenation, the ingress PE MUST + only concatenate cells up to the "Maximum Number of concatenated ATM + cells in a frame" interface parameter sub-TLV as received as part of + the control protocol [RFC4447]. + + When multiple ATM cells are encapsulated in the same PSN packet, the + ATM-specific byte MUST be repeated for each cell. This means that 51 + bytes are used to encapsulate each 53-byte ATM cell. + + + +Martini, et al. Standards Track [Page 25] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | PSN Transport Header (As Required) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Pseudowire Header | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |0 0 0 0| Resvd | Optional Sequence Number |M|V|Res| PTI |C| + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | VCI | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | + | | + | ATM Cell Payload (48 bytes) | + | | + | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | |M|V|Res| PTI |C| VCI | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | VCI | | + +-+-+-+-+-+-+-+-+ | + | ATM Cell Payload (48 bytes) | + | | + | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | | + +-+-+-+-+-+-+-+-+ + + Figure 10: Multiple Cell VPC Encapsulation + +10. ATM AAL5 CPCS-SDU Mode + + The AAL5 payload VCC service defines a mapping between the payload of + an AAL5 VCC and a single pseudowire. The AAL5 payload VCC service + requires ATM segmentation and reassembly support on the PE. + + The AAL5 payload CPCS-SDU service is OPTIONAL. + + Even the smallest TCP packet requires two ATM cells when sent over + AAL5 on a native ATM device. It is desirable to avoid this padding + on the pseudowire. Therefore, once the ingress PE reassembles the + AAL5 CPCS-PDU, the PE discards the PAD and CPCS-PDU trailer, and then + the ingress PE inserts the resulting payload into a pseudowire PDU. + + The egress PE MUST regenerate the PAD and trailer before transmitting + the AAL5 frame on the egress ATM port. + + This service does allow the transport of OAM and RM cells, but it + does not attempt to maintain the relative order of these cells with + respect to the cells that comprise the AAL5 CPCS-PDU. All OAM cells, + regardless of their type, that arrive during the reassembly of a + + + +Martini, et al. Standards Track [Page 26] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + single AAL5 CPCS-PDU are sent immediately on the pseudowire using + N-to-one cell encapsulation, followed by the AAL5 payload. + Therefore, the AAL5 payload VCC service will not be suitable for ATM + applications that require strict ordering of OAM cells (such as + performance monitoring and security applications). + +10.1. Transparent AAL5 SDU Frame Encapsulation + + The AAL5 CPCS-SDU is prepended by the following header: + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Res |T|E|C|U|Res| Length | Sequence Number (Optional) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | " | + | ATM cell or AAL5 CPCS-SDU | + | " | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + Figure 11: AAL5 CPCS-SDU Encapsulation + + The AAL5 payload service encapsulation requires the ATM control word. + The Flag bits are described below. + + * Res (Reserved) + + These bits are reserved and MUST be set to 0 upon transmission + and ignored upon reception. + + * T (transport type) bit + + Bit (T) of the control word indicates whether the packet contains + an ATM admin cell or an AAL5 payload. If T = 1, the packet + contains an ATM admin cell, encapsulated according to the N-to- + one cell relay encapsulation, Figure 4. If not set, the PDU + contains an AAL5 payload. The ability to transport an ATM cell + in the AAL5 SDU mode is intended to provide a means of enabling + administrative functionality over the AAL5 VCC (though it does + not endeavor to preserve user-cell and admin-cell + arrival/transport ordering). + + * E (EFCI) Bit + + The ingress router, PE1, SHOULD set this bit to 1 if the EFCI bit + of the final cell of those that transported the AAL5 CPCS-SDU is + set to 1, or if the EFCI bit of the single ATM cell to be + transported in the packet is set to 1. Otherwise, this bit + + + +Martini, et al. Standards Track [Page 27] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + SHOULD be set to 0. The egress router, PE2, SHOULD set the EFCI + bit of all cells that transport the AAL5 CPCS-SDU to the value + contained in this field. + + * C (CLP) Bit + + The ingress router, PE1, SHOULD set this bit to 1 if the CLP bit + of any of the ATM cells that transported the AAL5 CPCS-SDU is set + to 1, or if the CLP bit of the single ATM cell to be transported + in the packet is set to 1. Otherwise this bit SHOULD be set to + 0. The egress router, PE2, SHOULD set the CLP bit of all cells + that transport the AAL5 CPCS-SDU to the value contained in this + field. + + * U (Command/Response Field) Bit + + When FRF.8.1 Frame Relay/ATM PVC Service Interworking [RFC3916] + traffic is being transported, the CPCS-UU Least Significant Bit + (LSB) of the AAL5 CPCS-PDU may contain the Frame Relay C/R bit. + The ingress router, PE1, SHOULD copy this bit to the U bit of the + control word. The egress router, PE2, SHOULD copy the U bit to + the CPCS-UU Least Significant Bit (LSB) of the AAL5 CPCS PDU. + +11. AAL5 PDU Frame Mode + + The AAL5 payload PDU service is OPTIONAL. + +11.1. Transparent AAL5 PDU Frame Encapsulation + + In this mode, the ingress PE encapsulates the entire CPCS-PDU + including the PAD and trailer. + + This mode MAY support fragmentation procedures described in the + "Fragmentation" section below, in order to maintain OAM cell + sequencing. + + Like the ATM AAL5 payload VCC service, the AAL5 transparent VCC + service is intended to be more efficient than the VCC cell transport + service. However, the AAL5 transparent VCC service carries the + entire AAL5 CPCS-PDU, including the PAD and trailer. Note that the + AAL5 CPCS-PDU is not processed, i.e., an AAL5 frame with an invalid + CRC or length field will be transported. One reason for this is that + there may be a security agent that has scrambled the ATM cell + payloads that form the AAL5 CPCS-PDU. + + This service supports all OAM cell flows by using a fragmentation + procedure that ensures that OAM cells are not repositioned in respect + to AAL5 composite cells. + + + +Martini, et al. Standards Track [Page 28] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + The AAL5 transparent VCC service is OPTIONAL. + + 0 1 2 3 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | PSN Transport Header (As Required) | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | Pseudowire Header | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + |0 0 0 0| Resvd | Optional Sequence Number |M|V| Res |U|E|C| + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | " | + | AAL5 CPCS-PDU | + | (n * 48 bytes) | + | " | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + + Figure 12: AAL5 transparent service encapsulation + + The generic control word is inserted after the Pseudowire Header. + The presence of the control word is MANDATORY. + + The M, V, Res, and C bits are as defined earlier for VCC One-to-one + cell mode. + + * U Bit + + This field indicates whether this frame contains the last cell of + an AAL5 PDU and represents the value of the ATM User-to-User bit + for the last ATM cell of the PSN frame. Note: The ATM User-to- + User bit is the least significant bit of the PTI field in the ATM + header. This field is used to support the fragmentation + functionality described later in this section. + + * E (EFCI) bit + + This field is used to convey the EFCI state of the ATM cells. + The EFCI state is indicated in the middle bit of each ATM cell's + PTI field. + + ATM-to-PSN direction (ingress): The EFCI field of the control + byte is set to the EFCI state of the last cell of the AAL5 PDU or + AAL5 fragment. + + PSN-to-ATM direction (egress): The EFCI state of all constituent + cells of the AAL5 PDU or AAL5 fragment is set to the value of the + EFCI field in the control byte. + + + + +Martini, et al. Standards Track [Page 29] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + * C (CLP) bit + + This field is used to convey the cell loss priority of the ATM + cells. + + ATM-to-PSN direction (ingress): The CLP field of the control byte + is set to 1 if any of the constituent cells of the AAL5 PDU or + AAL5 fragment has its CLP bit set to 1; otherwise, this field is + set to 0. + + PSN-to-ATM direction (egress): The CLP bit of all constituent + cells for an AAL5 PDU or AAL5 fragment is set to the value of the + CLP field in the control byte. The payload consists of the + re-assembled AAL5 CPCS-PDU, including the AAL5 padding and + trailer or the AAL5 fragment. + +11.2. Fragmentation + + The ingress PE may not always be able to reassemble a full AAL5 + frame. This may be because the AAL5 PDU exceeds the pseudowire MTU + or because OAM cells arrive during reassembly of the AAL5 PDU. In + these cases, the AAL5 PDU shall be fragmented. In addition, + fragmentation may be desirable to bound ATM cell delay. + + When fragmentation occurs, the procedures described in the following + subsections shall be followed. + +11.2.1. Procedures in the ATM-to-PSN Direction + + The following procedures shall apply while fragmenting AAL5 PDUs: + + - Fragmentation shall always occur at cell boundaries within the + AAL5 PDU. + + - Set the UU bit to the value of the ATM User-to-User bit in the + cell header of the most recently received ATM cell. + + - The E and C bits of the fragment shall be set as defined in + section 9. + + - If the arriving cell is an OAM or an RM cell, send the current + PSN frame and then send the OAM or RM cell using One-to-one + single cell encapsulation (VCC). + + + + + + + + +Martini, et al. Standards Track [Page 30] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + +11.2.2. Procedures in the PSN-to-ATM Direction + + The following procedures shall apply: + + - The 3-bit PTI field of each ATM cell header is constructed as + follows: + + -i. The most significant bit is set to 0, indicating a user data + cell. + + -ii. The middle bit is set to the E bit value of the fragment. + + -iii. The least significant bit for the last ATM cell in the PSN + frame is set to the value of the UU bit of Figure 12. + + -iv. The least significant PTI bit is set to 0 for all other + cells in the PSN frame. + + - The CLP bit of each ATM cell header is set to the value of the C + bit of the control byte in Figure 12. + + - When a fragment is received, each constituent ATM cell is sent in + correct order. + +12. Mapping of ATM and PSN Classes of Service + + This section is provided for informational purposes, and for guidance + only. This section should not be considered part of the standard + proposed in this document. + + When ATM PW service is configured over a PSN, the ATM service + category of a connection SHOULD be mapped to a compatible class of + service in the PSN network. A compatible class of service maintains + the integrity of the service end to end. For example, the CBR + service category SHOULD be mapped to a class of service with + stringent loss and delay objectives. If the PSN implements the IP + Diffserv framework, a class of service based on the EF PHB is a good + candidate. + + Furthermore, ATM service categories have support for multiple + conformance definitions [TM4.0]. Some are CLP blind (e.g., CBR), + meaning that the QoS objectives apply to the aggregate CLP0+1 + conforming cell flow. Some are CLP significant (e.g., VBR.3), + meaning that the QoS objectives apply to the CLP0 conforming cell + flow only. + + When the PSN is MPLS based, a mapping between the CLP bit and the EXP + field can be performed to provide visibility of the cell loss + + + +Martini, et al. Standards Track [Page 31] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + priority in the MPLS network. The actual value to be marked in the + EXP field depends on the ATM service category, the ATM conformance + definition, and the type of tunnel LSP used (E-LSP or L-LSP). The + details of this mapping are outside the scope of this document. + Operators have the flexibility to design a specific mapping that + satisfies their own requirements. + + In both the ATM-to-PSN and PSN-to-ATM directions, the method used to + transfer the CLP and EFCI information of the individual cells into + the ATM-specific field, or flags, of the PW packet is described in + detail in sections 6 through 9 for each encapsulation mode. + +13. ILMI Support + + An MPLS edge PE MAY provide an ATM Integrated Local Management + Interface (ILMI) to the ATM edge switch. If an ingress PE receives + an ILMI message indicating that the ATM edge switch has deleted a VC, + or if the physical interface goes down, it MUST send a PW status + notification message for all PWs associated with the failure. When a + PW label mapping is withdrawn, or PW status notification message is + received, the egress PE MUST notify its client of this failure by + deleting the VC using ILMI. + +14. ATM-Specific Interface Parameter Sub-TLVs + + The Interface parameter TLV is defined in [RFC4447], and the IANA + registry with initial values for interface parameter sub-TLV types is + defined in [RFC4446], but the ATM PW-specific interface parameter is + specified as follows: + + - 0x02 Maximum Number of concatenated ATM cells. + + A 2-octet value specifying the maximum number of concatenated ATM + cells that can be processed as a single PDU by the egress PE. An + ingress PE transmitting concatenated cells on this PW can + concatenate a number of cells up to the value of this parameter, + but MUST NOT exceed it. This parameter is applicable only to PW + types 3, 9, 0x0a, 0xc, [RFC4446], and 0xd and is REQUIRED for + these PWC types. This parameter does not need to match in both + directions of a specific PW. + +15. Congestion Control + + As explained in [RFC3985], the PSN carrying the PW may be subject to + congestion, with congestion characteristics depending on PSN type, + network architecture, configuration, and loading. During congestion + the PSN may exhibit packet loss that will impact the service carried + by the ATM PW. In addition, since ATM PWs carry a variety of + + + +Martini, et al. Standards Track [Page 32] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + services across the PSN, including but not restricted to TCP/IP, they + may or may not behave in a TCP-friendly manner prescribed by + [RFC2914]. In the presence of services that reduce transmission + rate, ATM PWs may thus consume more than their fair share and in that + case SHOULD be halted. + + Whenever possible, ATM PWs should be run over traffic-engineered PSNs + providing bandwidth allocation and admission control mechanisms. + IntServ-enabled domains providing the Guaranteed Service (GS) or + Diffserv-enabled domains using EF (expedited forwarding) are examples + of traffic-engineered PSNs. Such PSNs will minimize loss and delay + while providing some degree of isolation of the ATM PW's effects from + neighboring streams. + + It should be noted that when transporting ATM, Diffserv-enabled + domains may use AF (Assured Forwarding) and/or DF (Default + Forwarding) instead of EF, in order to place less burden on the + network and gain additional statistical multiplexing advantage. In + particular, Table 1 of Appendix "V" in [ATM-MPLS] contains a detailed + mapping between ATM classes and Diffserv classes. + + The PEs SHOULD monitor for congestion (by using explicit congestion + notification, [VCCV], or by measuring packet loss) in order to ensure + that the service using the ATM PW may be maintained. When a PE + detects significant congestion while receiving the PW PDUs, the PE + MAY use RM cells for ABR connections to notify the remote PE. + + If the PW has been set up using the protocol defined in [RFC4447], + then procedures specified in [RFC4447] for status notification can be + used to disable packet transmission on the ingress PE from the egress + PE. The PW may be restarted by manual intervention, or by automatic + means after an appropriate waiting time. + +16. Security Considerations + + This document specifies only encapsulations, not the protocols used + to carry the encapsulated packets across the PSN. Each such protocol + may have its own set of security issues [RFC4447][RFC3985], but those + issues are not affected by the encapsulations specified herein. Note + that the security of the transported ATM service will only be as good + as the security of the PSN. This level of security might be less + rigorous than a native ATM service. + + + + + + + + + +Martini, et al. Standards Track [Page 33] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + +17. Normative References + + [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate + Requirement Levels", BCP 14, RFC 2119, March 1997. + + [RFC4447] Martini, L., Rosen, E., El-Aawar, N., Smith, T., and G. + Heron, "Pseudowire Setup and Maintenance Using the Label + Distribution Protocol (LDP)", RFC 4447, April 2006. + + [RFC3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., + Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack + Encoding", RFC 3032, January 2001. + + [RFC4446] Martini, L., "IANA Allocations for Pseudowire Edge to Edge + Emulation (PWE3)", BCP 116, RFC 4446, April 2006. + + [RFC4385] Bryant, S., Swallow, G., Martini, L., and D. McPherson, + "Pseudowire Emulation Edge-to-Edge (PWE3) Control Word for + Use over an MPLS PSN", RFC 4385, February 2006. + +18. Informative References + + [FBATM] ATM Forum Specification af-fbatm-0151.000 (2000), "Frame + Based ATM over SONET/SDH Transport (FAST)" + + [TM4.0] ATM Forum Specification af-tm-0121.000 (1999), "Traffic + Management Specification Version 4.1" + + [I.371] ITU-T Recommendation I.371 (2000), "Traffic control and + congestion control in B-ISDN". + + [I.610] ITU-T Recommendation I.610, (1999), "B-ISDN operation and + maintenance principles and functions". + + [Y.1411] ITU-T Recommendation Y.1411 (2003), ATM-MPLS Network + Interworking - Cell Mode user Plane Interworking + + [Y.1412] ITU-T Recommendation Y.1412 (2003), ATM-MPLS network + interworking - Frame mode user plane interworking + + [RFC3985] Bryant, S. and P. Pate, "Pseudo Wire Emulation Edge-to- + Edge (PWE3) Architecture", RFC 3985, March 2005. + + [RFC3916] Xiao, X., McPherson, D., and P. Pate, "Requirements for + Pseudo-Wire Emulation Edge-to-Edge (PWE3)", RFC 3916, + September 2004. + + + + + +Martini, et al. Standards Track [Page 34] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + [RFC4026] Andersson, L. and T. Madsen, "Provider Provisioned Virtual + Private Network (VPN) Terminology", RFC 4026, March 2005. + + [VCCV] Nadeau, T., Pignataro, C., and R. Aggarwal, "Pseudowire + Virtual Circuit Connectivity Verification (VCCV)", Work in + Progress, June 2006. + + [RFC2992] Hopps, C., "Analysis of an Equal-Cost Multi-Path + Algorithm", RFC 2992, November 2000. + + [ATM-MPLS] ATM Forum Specification af-aic-0178.001, "ATM-MPLS Network + Interworking Version 2.0", August 2003. + + [RFC2914] Floyd, S., "Congestion Control Principles", BCP 41, RFC + 2914, September 2000. + + [RFC2684] Grossman, D. and J. Heinanen, "Multiprotocol Encapsulation + over ATM Adaptation Layer 5", RFC 2684, September 1999. + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +Martini, et al. Standards Track [Page 35] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + +19. Significant Contributors + + Giles Heron + Tellabs + Abbey Place + 24-28 Easton Street + High Wycombe + Bucks + HP11 1NT + UK + EMail: giles.heron@tellabs.com + + + Dimitri Stratton Vlachos + Mazu Networks, Inc. + 125 Cambridgepark Drive + Cambridge, MA 02140 + EMail: d@mazunetworks.com + + + Dan Tappan + Cisco Systems, Inc. + 1414 Massachusetts Avenue + Boxborough, MA 01719 + EMail: tappan@cisco.com + + + Eric C. Rosen + Cisco Systems, Inc. + 1414 Massachusetts Avenue + Boxborough, MA 01719 + EMail: erosen@cisco.com + + + Steve Vogelsang + ECI Telecom + Omega Corporate Center + 1300 Omega Drive + Pittsburgh, PA 15205 + EMail: stephen.vogelsang@ecitele.com + + + Gerald de Grace + ECI Telecom + Omega Corporate Center + 1300 Omega Drive + Pittsburgh, PA 15205 + EMail: gerald.degrace@ecitele.com + + + +Martini, et al. Standards Track [Page 36] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + John Shirron + ECI Telecom + Omega Corporate Center + 1300 Omega Drive + Pittsburgh, PA 15205 + EMail: john.shirron@ecitele.com + + + Andrew G. Malis + Verizon Communications + 40 Sylvan Road + Waltham, MA + EMail: andrew.g.malis@verizon.com + Phone: 781-466-2362 + + + Vinai Sirkay + Redback Networks + 300 Holger Way + San Jose, CA 95134 + EMail: vsirkay@redback.com + + + Chris Liljenstolpe + Alcatel + 11600 Sallie Mae Dr. + 9th Floor + Reston, VA 20193 + EMail: chris.liljenstolpe@alcatel.com + + + Kireeti Kompella + Juniper Networks + 1194 N. Mathilda Ave + Sunnyvale, CA 94089 + EMail: kireeti@juniper.net + + + John Fischer + Alcatel + 600 March Rd + Kanata, ON, Canada. K2K 2E6 + EMail: john.fischer@alcatel.com + + + + + + + + +Martini, et al. Standards Track [Page 37] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + + Mustapha Aissaoui + Alcatel + 600 March Rd + Kanata, ON, Canada. K2K 2E6 + EMail: mustapha.aissaoui@alcatel.com + + + Tom Walsh + Lucent Technologies + 1 Robbins Road + Westford, MA 01886 USA + EMail: tdwalsh@lucent.com + + + John Rutemiller + Marconi Networks + 1000 Marconi Drive + Warrendale, PA 15086 + EMail: John.Rutemiller@marconi.com + + + Rick Wilder + Alcatel + 45195 Business Court + Loudoun Gateway II Suite 300 + M/S STERV-SMAE + Sterling, VA 20166 + EMail: Rick.Wilder@alcatel.com + + + Laura Dominik + Qwest Communications, Inc. + 600 Stinson Blvd. + Minneapolis, MN 55413 + Email: ldomini@qwest.com + + + + + + + + + + + + + + + + +Martini, et al. Standards Track [Page 38] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + +Authors' Addresses + + Luca Martini + Cisco Systems, Inc. + 9155 East Nichols Avenue, Suite 400 + Englewood, CO 80112 + EMail: lmartini@cisco.com + + + Jayakumar Jayakumar + Cisco Systems, Inc. + 225 E.Tasman, MS-SJ3/3 + San Jose, CA 95134 + EMail: jjayakum@cisco.com + + + Matthew Bocci + Alcatel + Grove House, Waltham Road Rd + White Waltham, Berks, UK. SL6 3TN + EMail: matthew.bocci@alcatel.co.uk + + + Nasser El-Aawar + Level 3 Communications, LLC. + 1025 Eldorado Blvd. + Broomfield, CO 80021 + EMail: nna@level3.net + + + Jeremy Brayley + ECI Telecom Inc. + Omega Corporate Center + 1300 Omega Drive + Pittsburgh, PA 15205 + EMail: jeremy.brayley@ecitele.com + + + Ghassem Koleyni + Nortel Networks + P O Box 3511, Station C Ottawa, Ontario, + K1Y 4H7 Canada + EMail: ghassem@nortelnetworks.com + + + + + + + + +Martini, et al. Standards Track [Page 39] + +RFC 4717 Encapsulation for ATM over MPLS December 2006 + + +Full Copyright Statement + + Copyright (C) The IETF Trust (2006). + + This document is subject to the rights, licenses and restrictions + contained in BCP 78, and except as set forth therein, the authors + retain all their rights. + + This document and the information contained herein are provided on an + "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS + OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST, + AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, + EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT + THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY + IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR + PURPOSE. + +Intellectual Property + + The IETF takes no position regarding the validity or scope of any + Intellectual Property Rights or other rights that might be claimed to + pertain to the implementation or use of the technology described in + this document or the extent to which any license under such rights + might or might not be available; nor does it represent that it has + made any independent effort to identify any such rights. Information + on the procedures with respect to rights in RFC documents can be + found in BCP 78 and BCP 79. + + Copies of IPR disclosures made to the IETF Secretariat and any + assurances of licenses to be made available, or the result of an + attempt made to obtain a general license or permission for the use of + such proprietary rights by implementers or users of this + specification can be obtained from the IETF on-line IPR repository at + http://www.ietf.org/ipr. + + The IETF invites any interested party to bring to its attention any + copyrights, patents or patent applications, or other proprietary + rights that may cover technology that may be required to implement + this standard. Please address the information to the IETF at + ietf-ipr@ietf.org. + +Acknowledgement + + Funding for the RFC Editor function is currently provided by the + Internet Society. + + + + + + +Martini, et al. Standards Track [Page 40] + |