summaryrefslogtreecommitdiff
path: root/doc/rfc/rfc2132.txt
diff options
context:
space:
mode:
Diffstat (limited to 'doc/rfc/rfc2132.txt')
-rw-r--r--doc/rfc/rfc2132.txt1907
1 files changed, 1907 insertions, 0 deletions
diff --git a/doc/rfc/rfc2132.txt b/doc/rfc/rfc2132.txt
new file mode 100644
index 0000000..e9c4f4b
--- /dev/null
+++ b/doc/rfc/rfc2132.txt
@@ -0,0 +1,1907 @@
+
+
+
+
+
+
+Network Working Group S. Alexander
+Request for Comments: 2132 Silicon Graphics, Inc.
+Obsoletes: 1533 R. Droms
+Category: Standards Track Bucknell University
+ March 1997
+
+ DHCP Options and BOOTP Vendor Extensions
+
+Status of this memo
+
+ This document specifies an Internet standards track protocol for the
+ Internet community, and requests discussion and suggestions for
+ improvements. Please refer to the current edition of the "Internet
+ Official Protocol Standards" (STD 1) for the standardization state
+ and status of this protocol. Distribution of this memo is unlimited.
+
+Abstract
+
+ The Dynamic Host Configuration Protocol (DHCP) [1] provides a
+ framework for passing configuration information to hosts on a TCP/IP
+ network. Configuration parameters and other control information are
+ carried in tagged data items that are stored in the 'options' field
+ of the DHCP message. The data items themselves are also called
+ "options."
+
+ This document specifies the current set of DHCP options. Future
+ options will be specified in separate RFCs. The current list of
+ valid options is also available in ftp://ftp.isi.edu/in-
+ notes/iana/assignments [22].
+
+ All of the vendor information extensions defined in RFC 1497 [2] may
+ be used as DHCP options. The definitions given in RFC 1497 are
+ included in this document, which supersedes RFC 1497. All of the
+ DHCP options defined in this document, except for those specific to
+ DHCP as defined in section 9, may be used as BOOTP vendor information
+ extensions.
+
+Table of Contents
+
+ 1. Introduction .............................................. 2
+ 2. BOOTP Extension/DHCP Option Field Format .................. 4
+ 3. RFC 1497 Vendor Extensions ................................ 5
+ 4. IP Layer Parameters per Host .............................. 11
+ 5. IP Layer Parameters per Interface ........................ 13
+ 6. Link Layer Parameters per Interface ....................... 16
+ 7. TCP Parameters ............................................ 17
+ 8. Application and Service Parameters ........................ 18
+ 9. DHCP Extensions ........................................... 25
+
+
+
+Alexander & Droms Standards Track [Page 1]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ 10. Defining new extensions ................................... 31
+ 11. Acknowledgements .......................................... 31
+ 12. References ................................................ 32
+ 13. Security Considerations ................................... 33
+ 14. Authors' Addresses ........................................ 34
+
+1. Introduction
+
+ This document specifies options for use with both the Dynamic Host
+ Configuration Protocol and the Bootstrap Protocol.
+
+ The full description of DHCP packet formats may be found in the DHCP
+ specification document [1], and the full description of BOOTP packet
+ formats may be found in the BOOTP specification document [3]. This
+ document defines the format of information in the last field of DHCP
+ packets ('options') and of BOOTP packets ('vend'). The remainder of
+ this section defines a generalized use of this area for giving
+ information useful to a wide class of machines, operating systems and
+ configurations. Sites with a single DHCP or BOOTP server that is
+ shared among heterogeneous clients may choose to define other, site-
+ specific formats for the use of the 'options' field.
+
+ Section 2 of this memo describes the formats of DHCP options and
+ BOOTP vendor extensions. Section 3 describes options defined in
+ previous documents for use with BOOTP (all may also be used with
+ DHCP). Sections 4-8 define new options intended for use with both
+ DHCP and BOOTP. Section 9 defines options used only in DHCP.
+
+ References further describing most of the options defined in sections
+ 2-6 can be found in section 12. The use of the options defined in
+ section 9 is described in the DHCP specification [1].
+
+ Information on registering new options is contained in section 10.
+
+ This document updates the definition of DHCP/BOOTP options that
+ appears in RFC1533. The classing mechanism has been extended to
+ include vendor classes as described in section 8.4 and 9.13. The new
+ procedure for defining new DHCP/BOOTP options in described in section
+ 10. Several new options, including NIS+ domain and servers, Mobile
+ IP home agent, SMTP server, TFTP server and Bootfile server, have
+ been added. Text giving definitions used throughout the document has
+ been added in section 1.1. Text emphasizing the need for uniqueness
+ of client-identifiers has been added to section 9.14.
+
+
+
+
+
+
+
+
+Alexander & Droms Standards Track [Page 2]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+1.1 Requirements
+
+ Throughout this document, the words that are used to define the
+ significance of particular requirements are capitalized. These words
+ are:
+
+ o "MUST"
+
+ This word or the adjective "REQUIRED" means that the item is an
+ absolute requirement of this specification.
+
+ o "MUST NOT"
+
+ This phrase means that the item is an absolute prohibition of
+ this specification.
+
+ o "SHOULD"
+
+ This word or the adjective "RECOMMENDED" means that there may
+ exist valid reasons in particular circumstances to ignore this
+ item, but the full implications should be understood and the case
+ carefully weighed before choosing a different course.
+
+ o "SHOULD NOT"
+
+ This phrase means that there may exist valid reasons in
+ particular circumstances when the listed behavior is acceptable
+ or even useful, but the full implications should be understood
+ and the case carefully weighed before implementing any behavior
+ described with this label.
+
+ o "MAY"
+
+ This word or the adjective "OPTIONAL" means that this item is
+ truly optional. One vendor may choose to include the item
+ because a particular marketplace requires it or because it
+ enhances the product, for example; another vendor may omit the
+ same item.
+
+1.2 Terminology
+
+ This document uses the following terms:
+
+ o "DHCP client"
+
+ A DHCP client or "client" is an Internet host using DHCP to
+ obtain configuration parameters such as a network address.
+
+
+
+
+Alexander & Droms Standards Track [Page 3]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ o "DHCP server"
+
+ A DHCP server of "server"is an Internet host that returns
+ configuration parameters to DHCP clients.
+
+ o "binding"
+
+ A binding is a collection of configuration parameters, including
+ at least an IP address, associated with or "bound to" a DHCP
+ client. Bindings are managed by DHCP servers.
+
+2. BOOTP Extension/DHCP Option Field Format
+
+
+ DHCP options have the same format as the BOOTP 'vendor extensions'
+ defined in RFC 1497 [2]. Options may be fixed length or variable
+ length. All options begin with a tag octet, which uniquely
+ identifies the option. Fixed-length options without data consist of
+ only a tag octet. Only options 0 and 255 are fixed length. All
+ other options are variable-length with a length octet following the
+ tag octet. The value of the length octet does not include the two
+ octets specifying the tag and length. The length octet is followed
+ by "length" octets of data. Options containing NVT ASCII data SHOULD
+ NOT include a trailing NULL; however, the receiver of such options
+ MUST be prepared to delete trailing nulls if they exist. The
+ receiver MUST NOT require that a trailing null be included in the
+ data. In the case of some variable-length options the length field
+ is a constant but must still be specified.
+
+ Any options defined subsequent to this document MUST contain a length
+ octet even if the length is fixed or zero.
+
+ All multi-octet quantities are in network byte-order.
+
+ When used with BOOTP, the first four octets of the vendor information
+ field have been assigned to the "magic cookie" (as suggested in RFC
+ 951). This field identifies the mode in which the succeeding data is
+ to be interpreted. The value of the magic cookie is the 4 octet
+ dotted decimal 99.130.83.99 (or hexadecimal number 63.82.53.63) in
+ network byte order.
+
+ All of the "vendor extensions" defined in RFC 1497 are also DHCP
+ options.
+
+ Option codes 128 to 254 (decimal) are reserved for site-specific
+ options.
+
+
+
+
+
+Alexander & Droms Standards Track [Page 4]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ Except for the options in section 9, all options may be used with
+ either DHCP or BOOTP.
+
+ Many of these options have their default values specified in other
+ documents. In particular, RFC 1122 [4] specifies default values for
+ most IP and TCP configuration parameters.
+
+ Many options supply one or more 32-bit IP address. Use of IP
+ addresses rather than fully-qualified Domain Names (FQDNs) may make
+ future renumbering of IP hosts more difficult. Use of these
+ addresses is discouraged at sites that may require renumbering.
+
+3. RFC 1497 Vendor Extensions
+
+ This section lists the vendor extensions as defined in RFC 1497.
+ They are defined here for completeness.
+
+3.1. Pad Option
+
+ The pad option can be used to cause subsequent fields to align on
+ word boundaries.
+
+ The code for the pad option is 0, and its length is 1 octet.
+
+ Code
+ +-----+
+ | 0 |
+ +-----+
+
+3.2. End Option
+
+ The end option marks the end of valid information in the vendor
+ field. Subsequent octets should be filled with pad options.
+
+ The code for the end option is 255, and its length is 1 octet.
+
+ Code
+ +-----+
+ | 255 |
+ +-----+
+
+3.3. Subnet Mask
+
+ The subnet mask option specifies the client's subnet mask as per RFC
+ 950 [5].
+
+ If both the subnet mask and the router option are specified in a DHCP
+ reply, the subnet mask option MUST be first.
+
+
+
+Alexander & Droms Standards Track [Page 5]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ The code for the subnet mask option is 1, and its length is 4 octets.
+
+ Code Len Subnet Mask
+ +-----+-----+-----+-----+-----+-----+
+ | 1 | 4 | m1 | m2 | m3 | m4 |
+ +-----+-----+-----+-----+-----+-----+
+
+3.4. Time Offset
+
+ The time offset field specifies the offset of the client's subnet in
+ seconds from Coordinated Universal Time (UTC). The offset is
+ expressed as a two's complement 32-bit integer. A positive offset
+ indicates a location east of the zero meridian and a negative offset
+ indicates a location west of the zero meridian.
+
+ The code for the time offset option is 2, and its length is 4 octets.
+
+ Code Len Time Offset
+ +-----+-----+-----+-----+-----+-----+
+ | 2 | 4 | n1 | n2 | n3 | n4 |
+ +-----+-----+-----+-----+-----+-----+
+
+3.5. Router Option
+
+ The router option specifies a list of IP addresses for routers on the
+ client's subnet. Routers SHOULD be listed in order of preference.
+
+ The code for the router option is 3. The minimum length for the
+ router option is 4 octets, and the length MUST always be a multiple
+ of 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 3 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+3.6. Time Server Option
+
+ The time server option specifies a list of RFC 868 [6] time servers
+ available to the client. Servers SHOULD be listed in order of
+ preference.
+
+ The code for the time server option is 4. The minimum length for
+ this option is 4 octets, and the length MUST always be a multiple of
+ 4.
+
+
+
+
+
+
+Alexander & Droms Standards Track [Page 6]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 4 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+3.7. Name Server Option
+
+ The name server option specifies a list of IEN 116 [7] name servers
+ available to the client. Servers SHOULD be listed in order of
+ preference.
+
+ The code for the name server option is 5. The minimum length for
+ this option is 4 octets, and the length MUST always be a multiple of
+ 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 5 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+3.8. Domain Name Server Option
+
+ The domain name server option specifies a list of Domain Name System
+ (STD 13, RFC 1035 [8]) name servers available to the client. Servers
+ SHOULD be listed in order of preference.
+
+ The code for the domain name server option is 6. The minimum length
+ for this option is 4 octets, and the length MUST always be a multiple
+ of 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 6 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+3.9. Log Server Option
+
+ The log server option specifies a list of MIT-LCS UDP log servers
+ available to the client. Servers SHOULD be listed in order of
+ preference.
+
+ The code for the log server option is 7. The minimum length for this
+ option is 4 octets, and the length MUST always be a multiple of 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 7 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+
+
+Alexander & Droms Standards Track [Page 7]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+3.10. Cookie Server Option
+
+ The cookie server option specifies a list of RFC 865 [9] cookie
+ servers available to the client. Servers SHOULD be listed in order
+ of preference.
+
+ The code for the log server option is 8. The minimum length for this
+ option is 4 octets, and the length MUST always be a multiple of 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 8 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+3.11. LPR Server Option
+
+ The LPR server option specifies a list of RFC 1179 [10] line printer
+ servers available to the client. Servers SHOULD be listed in order
+ of preference.
+
+ The code for the LPR server option is 9. The minimum length for this
+ option is 4 octets, and the length MUST always be a multiple of 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 9 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+3.12. Impress Server Option
+
+ The Impress server option specifies a list of Imagen Impress servers
+ available to the client. Servers SHOULD be listed in order of
+ preference.
+
+ The code for the Impress server option is 10. The minimum length for
+ this option is 4 octets, and the length MUST always be a multiple of
+ 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 10 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+3.13. Resource Location Server Option
+
+ This option specifies a list of RFC 887 [11] Resource Location
+ servers available to the client. Servers SHOULD be listed in order
+ of preference.
+
+
+
+Alexander & Droms Standards Track [Page 8]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ The code for this option is 11. The minimum length for this option
+ is 4 octets, and the length MUST always be a multiple of 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 11 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+3.14. Host Name Option
+
+ This option specifies the name of the client. The name may or may
+ not be qualified with the local domain name (see section 3.17 for the
+ preferred way to retrieve the domain name). See RFC 1035 for
+ character set restrictions.
+
+ The code for this option is 12, and its minimum length is 1.
+
+ Code Len Host Name
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 12 | n | h1 | h2 | h3 | h4 | h5 | h6 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+3.15. Boot File Size Option
+
+ This option specifies the length in 512-octet blocks of the default
+ boot image for the client. The file length is specified as an
+ unsigned 16-bit integer.
+
+ The code for this option is 13, and its length is 2.
+
+ Code Len File Size
+ +-----+-----+-----+-----+
+ | 13 | 2 | l1 | l2 |
+ +-----+-----+-----+-----+
+
+3.16. Merit Dump File
+
+ This option specifies the path-name of a file to which the client's
+ core image should be dumped in the event the client crashes. The
+ path is formatted as a character string consisting of characters from
+ the NVT ASCII character set.
+
+ The code for this option is 14. Its minimum length is 1.
+
+ Code Len Dump File Pathname
+ +-----+-----+-----+-----+-----+-----+---
+ | 14 | n | n1 | n2 | n3 | n4 | ...
+ +-----+-----+-----+-----+-----+-----+---
+
+
+
+Alexander & Droms Standards Track [Page 9]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+3.17. Domain Name
+
+ This option specifies the domain name that client should use when
+ resolving hostnames via the Domain Name System.
+
+ The code for this option is 15. Its minimum length is 1.
+
+ Code Len Domain Name
+ +-----+-----+-----+-----+-----+-----+--
+ | 15 | n | d1 | d2 | d3 | d4 | ...
+ +-----+-----+-----+-----+-----+-----+--
+
+3.18. Swap Server
+
+ This specifies the IP address of the client's swap server.
+
+ The code for this option is 16 and its length is 4.
+
+ Code Len Swap Server Address
+ +-----+-----+-----+-----+-----+-----+
+ | 16 | n | a1 | a2 | a3 | a4 |
+ +-----+-----+-----+-----+-----+-----+
+
+3.19. Root Path
+
+ This option specifies the path-name that contains the client's root
+ disk. The path is formatted as a character string consisting of
+ characters from the NVT ASCII character set.
+
+ The code for this option is 17. Its minimum length is 1.
+
+ Code Len Root Disk Pathname
+ +-----+-----+-----+-----+-----+-----+---
+ | 17 | n | n1 | n2 | n3 | n4 | ...
+ +-----+-----+-----+-----+-----+-----+---
+
+3.20. Extensions Path
+
+ A string to specify a file, retrievable via TFTP, which contains
+ information which can be interpreted in the same way as the 64-octet
+ vendor-extension field within the BOOTP response, with the following
+ exceptions:
+
+ - the length of the file is unconstrained;
+ - all references to Tag 18 (i.e., instances of the
+ BOOTP Extensions Path field) within the file are
+ ignored.
+
+
+
+
+Alexander & Droms Standards Track [Page 10]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ The code for this option is 18. Its minimum length is 1.
+
+ Code Len Extensions Pathname
+ +-----+-----+-----+-----+-----+-----+---
+ | 18 | n | n1 | n2 | n3 | n4 | ...
+ +-----+-----+-----+-----+-----+-----+---
+
+4. IP Layer Parameters per Host
+
+ This section details the options that affect the operation of the IP
+ layer on a per-host basis.
+
+4.1. IP Forwarding Enable/Disable Option
+
+ This option specifies whether the client should configure its IP
+ layer for packet forwarding. A value of 0 means disable IP
+ forwarding, and a value of 1 means enable IP forwarding.
+
+ The code for this option is 19, and its length is 1.
+
+ Code Len Value
+ +-----+-----+-----+
+ | 19 | 1 | 0/1 |
+ +-----+-----+-----+
+
+4.2. Non-Local Source Routing Enable/Disable Option
+
+ This option specifies whether the client should configure its IP
+ layer to allow forwarding of datagrams with non-local source routes
+ (see Section 3.3.5 of [4] for a discussion of this topic). A value
+ of 0 means disallow forwarding of such datagrams, and a value of 1
+ means allow forwarding.
+
+ The code for this option is 20, and its length is 1.
+
+ Code Len Value
+ +-----+-----+-----+
+ | 20 | 1 | 0/1 |
+ +-----+-----+-----+
+
+4.3. Policy Filter Option
+
+ This option specifies policy filters for non-local source routing.
+ The filters consist of a list of IP addresses and masks which specify
+ destination/mask pairs with which to filter incoming source routes.
+
+ Any source routed datagram whose next-hop address does not match one
+ of the filters should be discarded by the client.
+
+
+
+Alexander & Droms Standards Track [Page 11]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ See [4] for further information.
+
+ The code for this option is 21. The minimum length of this option is
+ 8, and the length MUST be a multiple of 8.
+
+ Code Len Address 1 Mask 1
+ +-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
+ | 21 | n | a1 | a2 | a3 | a4 | m1 | m2 | m3 | m4 |
+ +-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
+ Address 2 Mask 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+---
+ | a1 | a2 | a3 | a4 | m1 | m2 | m3 | m4 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+---
+
+4.4. Maximum Datagram Reassembly Size
+
+ This option specifies the maximum size datagram that the client
+ should be prepared to reassemble. The size is specified as a 16-bit
+ unsigned integer. The minimum value legal value is 576.
+
+ The code for this option is 22, and its length is 2.
+
+ Code Len Size
+ +-----+-----+-----+-----+
+ | 22 | 2 | s1 | s2 |
+ +-----+-----+-----+-----+
+
+4.5. Default IP Time-to-live
+
+ This option specifies the default time-to-live that the client should
+ use on outgoing datagrams. The TTL is specified as an octet with a
+ value between 1 and 255.
+
+ The code for this option is 23, and its length is 1.
+
+ Code Len TTL
+ +-----+-----+-----+
+ | 23 | 1 | ttl |
+ +-----+-----+-----+
+
+4.6. Path MTU Aging Timeout Option
+
+ This option specifies the timeout (in seconds) to use when aging Path
+ MTU values discovered by the mechanism defined in RFC 1191 [12]. The
+ timeout is specified as a 32-bit unsigned integer.
+
+ The code for this option is 24, and its length is 4.
+
+
+
+
+Alexander & Droms Standards Track [Page 12]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ Code Len Timeout
+ +-----+-----+-----+-----+-----+-----+
+ | 24 | 4 | t1 | t2 | t3 | t4 |
+ +-----+-----+-----+-----+-----+-----+
+
+4.7. Path MTU Plateau Table Option
+
+ This option specifies a table of MTU sizes to use when performing
+ Path MTU Discovery as defined in RFC 1191. The table is formatted as
+ a list of 16-bit unsigned integers, ordered from smallest to largest.
+ The minimum MTU value cannot be smaller than 68.
+
+ The code for this option is 25. Its minimum length is 2, and the
+ length MUST be a multiple of 2.
+
+ Code Len Size 1 Size 2
+ +-----+-----+-----+-----+-----+-----+---
+ | 25 | n | s1 | s2 | s1 | s2 | ...
+ +-----+-----+-----+-----+-----+-----+---
+
+5. IP Layer Parameters per Interface
+
+ This section details the options that affect the operation of the IP
+ layer on a per-interface basis. It is expected that a client can
+ issue multiple requests, one per interface, in order to configure
+ interfaces with their specific parameters.
+
+5.1. Interface MTU Option
+
+ This option specifies the MTU to use on this interface. The MTU is
+ specified as a 16-bit unsigned integer. The minimum legal value for
+ the MTU is 68.
+
+ The code for this option is 26, and its length is 2.
+
+ Code Len MTU
+ +-----+-----+-----+-----+
+ | 26 | 2 | m1 | m2 |
+ +-----+-----+-----+-----+
+
+5.2. All Subnets are Local Option
+
+ This option specifies whether or not the client may assume that all
+ subnets of the IP network to which the client is connected use the
+ same MTU as the subnet of that network to which the client is
+ directly connected. A value of 1 indicates that all subnets share
+ the same MTU. A value of 0 means that the client should assume that
+ some subnets of the directly connected network may have smaller MTUs.
+
+
+
+Alexander & Droms Standards Track [Page 13]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ The code for this option is 27, and its length is 1.
+
+ Code Len Value
+ +-----+-----+-----+
+ | 27 | 1 | 0/1 |
+ +-----+-----+-----+
+
+5.3. Broadcast Address Option
+
+ This option specifies the broadcast address in use on the client's
+ subnet. Legal values for broadcast addresses are specified in
+ section 3.2.1.3 of [4].
+
+ The code for this option is 28, and its length is 4.
+
+ Code Len Broadcast Address
+ +-----+-----+-----+-----+-----+-----+
+ | 28 | 4 | b1 | b2 | b3 | b4 |
+ +-----+-----+-----+-----+-----+-----+
+
+5.4. Perform Mask Discovery Option
+
+ This option specifies whether or not the client should perform subnet
+ mask discovery using ICMP. A value of 0 indicates that the client
+ should not perform mask discovery. A value of 1 means that the
+ client should perform mask discovery.
+
+ The code for this option is 29, and its length is 1.
+
+ Code Len Value
+ +-----+-----+-----+
+ | 29 | 1 | 0/1 |
+ +-----+-----+-----+
+
+5.5. Mask Supplier Option
+
+ This option specifies whether or not the client should respond to
+ subnet mask requests using ICMP. A value of 0 indicates that the
+ client should not respond. A value of 1 means that the client should
+ respond.
+
+ The code for this option is 30, and its length is 1.
+
+ Code Len Value
+ +-----+-----+-----+
+ | 30 | 1 | 0/1 |
+ +-----+-----+-----+
+
+
+
+
+Alexander & Droms Standards Track [Page 14]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+5.6. Perform Router Discovery Option
+
+ This option specifies whether or not the client should solicit
+ routers using the Router Discovery mechanism defined in RFC 1256
+ [13]. A value of 0 indicates that the client should not perform
+ router discovery. A value of 1 means that the client should perform
+ router discovery.
+
+ The code for this option is 31, and its length is 1.
+
+ Code Len Value
+ +-----+-----+-----+
+ | 31 | 1 | 0/1 |
+ +-----+-----+-----+
+
+5.7. Router Solicitation Address Option
+
+ This option specifies the address to which the client should transmit
+ router solicitation requests.
+
+ The code for this option is 32, and its length is 4.
+
+ Code Len Address
+ +-----+-----+-----+-----+-----+-----+
+ | 32 | 4 | a1 | a2 | a3 | a4 |
+ +-----+-----+-----+-----+-----+-----+
+
+5.8. Static Route Option
+
+ This option specifies a list of static routes that the client should
+ install in its routing cache. If multiple routes to the same
+ destination are specified, they are listed in descending order of
+ priority.
+
+ The routes consist of a list of IP address pairs. The first address
+ is the destination address, and the second address is the router for
+ the destination.
+
+ The default route (0.0.0.0) is an illegal destination for a static
+ route. See section 3.5 for information about the router option.
+
+ The code for this option is 33. The minimum length of this option is
+ 8, and the length MUST be a multiple of 8.
+
+
+
+
+
+
+
+
+Alexander & Droms Standards Track [Page 15]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ Code Len Destination 1 Router 1
+ +-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
+ | 33 | n | d1 | d2 | d3 | d4 | r1 | r2 | r3 | r4 |
+ +-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
+ Destination 2 Router 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+---
+ | d1 | d2 | d3 | d4 | r1 | r2 | r3 | r4 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+---
+
+6. Link Layer Parameters per Interface
+
+ This section lists the options that affect the operation of the data
+ link layer on a per-interface basis.
+
+6.1. Trailer Encapsulation Option
+
+ This option specifies whether or not the client should negotiate the
+ use of trailers (RFC 893 [14]) when using the ARP protocol. A value
+ of 0 indicates that the client should not attempt to use trailers. A
+ value of 1 means that the client should attempt to use trailers.
+
+ The code for this option is 34, and its length is 1.
+
+ Code Len Value
+ +-----+-----+-----+
+ | 34 | 1 | 0/1 |
+ +-----+-----+-----+
+
+6.2. ARP Cache Timeout Option
+
+ This option specifies the timeout in seconds for ARP cache entries.
+ The time is specified as a 32-bit unsigned integer.
+
+ The code for this option is 35, and its length is 4.
+
+ Code Len Time
+ +-----+-----+-----+-----+-----+-----+
+ | 35 | 4 | t1 | t2 | t3 | t4 |
+ +-----+-----+-----+-----+-----+-----+
+
+6.3. Ethernet Encapsulation Option
+
+ This option specifies whether or not the client should use Ethernet
+ Version 2 (RFC 894 [15]) or IEEE 802.3 (RFC 1042 [16]) encapsulation
+ if the interface is an Ethernet. A value of 0 indicates that the
+ client should use RFC 894 encapsulation. A value of 1 means that the
+ client should use RFC 1042 encapsulation.
+
+
+
+
+Alexander & Droms Standards Track [Page 16]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ The code for this option is 36, and its length is 1.
+
+ Code Len Value
+ +-----+-----+-----+
+ | 36 | 1 | 0/1 |
+ +-----+-----+-----+
+
+7. TCP Parameters
+
+ This section lists the options that affect the operation of the TCP
+ layer on a per-interface basis.
+
+7.1. TCP Default TTL Option
+
+ This option specifies the default TTL that the client should use when
+ sending TCP segments. The value is represented as an 8-bit unsigned
+ integer. The minimum value is 1.
+
+ The code for this option is 37, and its length is 1.
+
+ Code Len TTL
+ +-----+-----+-----+
+ | 37 | 1 | n |
+ +-----+-----+-----+
+
+7.2. TCP Keepalive Interval Option
+
+ This option specifies the interval (in seconds) that the client TCP
+ should wait before sending a keepalive message on a TCP connection.
+ The time is specified as a 32-bit unsigned integer. A value of zero
+ indicates that the client should not generate keepalive messages on
+ connections unless specifically requested by an application.
+
+ The code for this option is 38, and its length is 4.
+
+ Code Len Time
+ +-----+-----+-----+-----+-----+-----+
+ | 38 | 4 | t1 | t2 | t3 | t4 |
+ +-----+-----+-----+-----+-----+-----+
+
+7.3. TCP Keepalive Garbage Option
+
+ This option specifies the whether or not the client should send TCP
+ keepalive messages with a octet of garbage for compatibility with
+ older implementations. A value of 0 indicates that a garbage octet
+ should not be sent. A value of 1 indicates that a garbage octet
+ should be sent.
+
+
+
+
+Alexander & Droms Standards Track [Page 17]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ The code for this option is 39, and its length is 1.
+
+ Code Len Value
+ +-----+-----+-----+
+ | 39 | 1 | 0/1 |
+ +-----+-----+-----+
+
+8. Application and Service Parameters
+
+ This section details some miscellaneous options used to configure
+ miscellaneous applications and services.
+
+8.1. Network Information Service Domain Option
+
+ This option specifies the name of the client's NIS [17] domain. The
+ domain is formatted as a character string consisting of characters
+ from the NVT ASCII character set.
+
+ The code for this option is 40. Its minimum length is 1.
+
+ Code Len NIS Domain Name
+ +-----+-----+-----+-----+-----+-----+---
+ | 40 | n | n1 | n2 | n3 | n4 | ...
+ +-----+-----+-----+-----+-----+-----+---
+
+8.2. Network Information Servers Option
+
+ This option specifies a list of IP addresses indicating NIS servers
+ available to the client. Servers SHOULD be listed in order of
+ preference.
+
+ The code for this option is 41. Its minimum length is 4, and the
+ length MUST be a multiple of 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 41 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+8.3. Network Time Protocol Servers Option
+
+ This option specifies a list of IP addresses indicating NTP [18]
+ servers available to the client. Servers SHOULD be listed in order
+ of preference.
+
+ The code for this option is 42. Its minimum length is 4, and the
+ length MUST be a multiple of 4.
+
+
+
+
+Alexander & Droms Standards Track [Page 18]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 42 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+8.4. Vendor Specific Information
+
+ This option is used by clients and servers to exchange vendor-
+ specific information. The information is an opaque object of n
+ octets, presumably interpreted by vendor-specific code on the clients
+ and servers. The definition of this information is vendor specific.
+ The vendor is indicated in the vendor class identifier option.
+ Servers not equipped to interpret the vendor-specific information
+ sent by a client MUST ignore it (although it may be reported).
+ Clients which do not receive desired vendor-specific information
+ SHOULD make an attempt to operate without it, although they may do so
+ (and announce they are doing so) in a degraded mode.
+
+ If a vendor potentially encodes more than one item of information in
+ this option, then the vendor SHOULD encode the option using
+ "Encapsulated vendor-specific options" as described below:
+
+ The Encapsulated vendor-specific options field SHOULD be encoded as a
+ sequence of code/length/value fields of identical syntax to the DHCP
+ options field with the following exceptions:
+
+ 1) There SHOULD NOT be a "magic cookie" field in the encapsulated
+ vendor-specific extensions field.
+
+ 2) Codes other than 0 or 255 MAY be redefined by the vendor within
+ the encapsulated vendor-specific extensions field, but SHOULD
+ conform to the tag-length-value syntax defined in section 2.
+
+ 3) Code 255 (END), if present, signifies the end of the
+ encapsulated vendor extensions, not the end of the vendor
+ extensions field. If no code 255 is present, then the end of
+ the enclosing vendor-specific information field is taken as the
+ end of the encapsulated vendor-specific extensions field.
+
+ The code for this option is 43 and its minimum length is 1.
+
+ Code Len Vendor-specific information
+ +-----+-----+-----+-----+---
+ | 43 | n | i1 | i2 | ...
+ +-----+-----+-----+-----+---
+
+
+
+
+
+
+Alexander & Droms Standards Track [Page 19]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ When encapsulated vendor-specific extensions are used, the
+ information bytes 1-n have the following format:
+
+ Code Len Data item Code Len Data item Code
+ +-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
+ | T1 | n | d1 | d2 | ... | T2 | n | D1 | D2 | ... | ... |
+ +-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
+
+8.5. NetBIOS over TCP/IP Name Server Option
+
+ The NetBIOS name server (NBNS) option specifies a list of RFC
+ 1001/1002 [19] [20] NBNS name servers listed in order of preference.
+
+ The code for this option is 44. The minimum length of the option is
+ 4 octets, and the length must always be a multiple of 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+----
+ | 44 | n | a1 | a2 | a3 | a4 | b1 | b2 | b3 | b4 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+----
+
+8.6. NetBIOS over TCP/IP Datagram Distribution Server Option
+
+ The NetBIOS datagram distribution server (NBDD) option specifies a
+ list of RFC 1001/1002 NBDD servers listed in order of preference. The
+ code for this option is 45. The minimum length of the option is 4
+ octets, and the length must always be a multiple of 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+----
+ | 45 | n | a1 | a2 | a3 | a4 | b1 | b2 | b3 | b4 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+----
+
+8.7. NetBIOS over TCP/IP Node Type Option
+
+ The NetBIOS node type option allows NetBIOS over TCP/IP clients which
+ are configurable to be configured as described in RFC 1001/1002. The
+ value is specified as a single octet which identifies the client type
+ as follows:
+
+ Value Node Type
+ ----- ---------
+ 0x1 B-node
+ 0x2 P-node
+ 0x4 M-node
+ 0x8 H-node
+
+
+
+
+
+Alexander & Droms Standards Track [Page 20]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ In the above chart, the notation '0x' indicates a number in base-16
+ (hexadecimal).
+
+ The code for this option is 46. The length of this option is always
+ 1.
+
+ Code Len Node Type
+ +-----+-----+-----------+
+ | 46 | 1 | see above |
+ +-----+-----+-----------+
+
+8.8. NetBIOS over TCP/IP Scope Option
+
+ The NetBIOS scope option specifies the NetBIOS over TCP/IP scope
+ parameter for the client as specified in RFC 1001/1002. See [19],
+ [20], and [8] for character-set restrictions.
+
+ The code for this option is 47. The minimum length of this option is
+ 1.
+
+ Code Len NetBIOS Scope
+ +-----+-----+-----+-----+-----+-----+----
+ | 47 | n | s1 | s2 | s3 | s4 | ...
+ +-----+-----+-----+-----+-----+-----+----
+
+8.9. X Window System Font Server Option
+
+ This option specifies a list of X Window System [21] Font servers
+ available to the client. Servers SHOULD be listed in order of
+ preference.
+
+ The code for this option is 48. The minimum length of this option is
+ 4 octets, and the length MUST be a multiple of 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+---
+ | 48 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+---
+
+8.10. X Window System Display Manager Option
+
+ This option specifies a list of IP addresses of systems that are
+ running the X Window System Display Manager and are available to the
+ client.
+
+ Addresses SHOULD be listed in order of preference.
+
+
+
+
+
+Alexander & Droms Standards Track [Page 21]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ The code for the this option is 49. The minimum length of this option
+ is 4, and the length MUST be a multiple of 4.
+
+ Code Len Address 1 Address 2
+
+ +-----+-----+-----+-----+-----+-----+-----+-----+---
+ | 49 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+---
+
+8.11. Network Information Service+ Domain Option
+
+ This option specifies the name of the client's NIS+ [17] domain. The
+ domain is formatted as a character string consisting of characters
+ from the NVT ASCII character set.
+
+ The code for this option is 64. Its minimum length is 1.
+
+ Code Len NIS Client Domain Name
+ +-----+-----+-----+-----+-----+-----+---
+ | 64 | n | n1 | n2 | n3 | n4 | ...
+ +-----+-----+-----+-----+-----+-----+---
+
+8.12. Network Information Service+ Servers Option
+
+ This option specifies a list of IP addresses indicating NIS+ servers
+ available to the client. Servers SHOULD be listed in order of
+ preference.
+
+ The code for this option is 65. Its minimum length is 4, and the
+ length MUST be a multiple of 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 65 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+8.13. Mobile IP Home Agent option
+
+ This option specifies a list of IP addresses indicating mobile IP
+ home agents available to the client. Agents SHOULD be listed in
+ order of preference.
+
+ The code for this option is 68. Its minimum length is 0 (indicating
+ no home agents are available) and the length MUST be a multiple of 4.
+ It is expected that the usual length will be four octets, containing
+ a single home agent's address.
+
+
+
+
+
+Alexander & Droms Standards Track [Page 22]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ Code Len Home Agent Addresses (zero or more)
+ +-----+-----+-----+-----+-----+-----+--
+ | 68 | n | a1 | a2 | a3 | a4 | ...
+ +-----+-----+-----+-----+-----+-----+--
+
+8.14. Simple Mail Transport Protocol (SMTP) Server Option
+
+ The SMTP server option specifies a list of SMTP servers available to
+ the client. Servers SHOULD be listed in order of preference.
+
+ The code for the SMTP server option is 69. The minimum length for
+ this option is 4 octets, and the length MUST always be a multiple of
+ 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 69 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+8.15. Post Office Protocol (POP3) Server Option
+
+ The POP3 server option specifies a list of POP3 available to the
+ client. Servers SHOULD be listed in order of preference.
+
+ The code for the POP3 server option is 70. The minimum length for
+ this option is 4 octets, and the length MUST always be a multiple of
+ 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 70 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+8.16. Network News Transport Protocol (NNTP) Server Option
+
+ The NNTP server option specifies a list of NNTP available to the
+ client. Servers SHOULD be listed in order of preference.
+
+ The code for the NNTP server option is 71. The minimum length for
+ this option is 4 octets, and the length MUST always be a multiple of
+ 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 71 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+
+
+
+
+Alexander & Droms Standards Track [Page 23]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+8.17. Default World Wide Web (WWW) Server Option
+
+ The WWW server option specifies a list of WWW available to the
+ client. Servers SHOULD be listed in order of preference.
+
+ The code for the WWW server option is 72. The minimum length for
+ this option is 4 octets, and the length MUST always be a multiple of
+ 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 72 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+8.18. Default Finger Server Option
+
+ The Finger server option specifies a list of Finger available to the
+ client. Servers SHOULD be listed in order of preference.
+
+ The code for the Finger server option is 73. The minimum length for
+ this option is 4 octets, and the length MUST always be a multiple of
+ 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 73 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+8.19. Default Internet Relay Chat (IRC) Server Option
+
+ The IRC server option specifies a list of IRC available to the
+ client. Servers SHOULD be listed in order of preference.
+
+ The code for the IRC server option is 74. The minimum length for
+ this option is 4 octets, and the length MUST always be a multiple of
+ 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 74 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+8.20. StreetTalk Server Option
+
+ The StreetTalk server option specifies a list of StreetTalk servers
+ available to the client. Servers SHOULD be listed in order of
+ preference.
+
+
+
+
+Alexander & Droms Standards Track [Page 24]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ The code for the StreetTalk server option is 75. The minimum length
+ for this option is 4 octets, and the length MUST always be a multiple
+ of 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 75 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+8.21. StreetTalk Directory Assistance (STDA) Server Option
+
+ The StreetTalk Directory Assistance (STDA) server option specifies a
+ list of STDA servers available to the client. Servers SHOULD be
+ listed in order of preference.
+
+ The code for the StreetTalk Directory Assistance server option is 76.
+ The minimum length for this option is 4 octets, and the length MUST
+ always be a multiple of 4.
+
+ Code Len Address 1 Address 2
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+ | 76 | n | a1 | a2 | a3 | a4 | a1 | a2 | ...
+ +-----+-----+-----+-----+-----+-----+-----+-----+--
+
+9. DHCP Extensions
+
+ This section details the options that are specific to DHCP.
+
+9.1. Requested IP Address
+
+ This option is used in a client request (DHCPDISCOVER) to allow the
+ client to request that a particular IP address be assigned.
+
+ The code for this option is 50, and its length is 4.
+
+ Code Len Address
+ +-----+-----+-----+-----+-----+-----+
+ | 50 | 4 | a1 | a2 | a3 | a4 |
+ +-----+-----+-----+-----+-----+-----+
+
+9.2. IP Address Lease Time
+
+ This option is used in a client request (DHCPDISCOVER or DHCPREQUEST)
+ to allow the client to request a lease time for the IP address. In a
+ server reply (DHCPOFFER), a DHCP server uses this option to specify
+ the lease time it is willing to offer.
+
+
+
+
+
+Alexander & Droms Standards Track [Page 25]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ The time is in units of seconds, and is specified as a 32-bit
+ unsigned integer.
+
+ The code for this option is 51, and its length is 4.
+
+ Code Len Lease Time
+ +-----+-----+-----+-----+-----+-----+
+ | 51 | 4 | t1 | t2 | t3 | t4 |
+ +-----+-----+-----+-----+-----+-----+
+
+9.3. Option Overload
+
+ This option is used to indicate that the DHCP 'sname' or 'file'
+ fields are being overloaded by using them to carry DHCP options. A
+ DHCP server inserts this option if the returned parameters will
+ exceed the usual space allotted for options.
+
+ If this option is present, the client interprets the specified
+ additional fields after it concludes interpretation of the standard
+ option fields.
+
+ The code for this option is 52, and its length is 1. Legal values
+ for this option are:
+
+ Value Meaning
+ ----- --------
+ 1 the 'file' field is used to hold options
+ 2 the 'sname' field is used to hold options
+ 3 both fields are used to hold options
+
+ Code Len Value
+ +-----+-----+-----+
+ | 52 | 1 |1/2/3|
+ +-----+-----+-----+
+
+9.4 TFTP server name
+
+ This option is used to identify a TFTP server when the 'sname' field
+ in the DHCP header has been used for DHCP options.
+
+ The code for this option is 66, and its minimum length is 1.
+
+ Code Len TFTP server
+ +-----+-----+-----+-----+-----+---
+ | 66 | n | c1 | c2 | c3 | ...
+ +-----+-----+-----+-----+-----+---
+
+
+
+
+
+Alexander & Droms Standards Track [Page 26]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+9.5 Bootfile name
+
+ This option is used to identify a bootfile when the 'file' field in
+ the DHCP header has been used for DHCP options.
+
+ The code for this option is 67, and its minimum length is 1.
+
+ Code Len Bootfile name
+ +-----+-----+-----+-----+-----+---
+ | 67 | n | c1 | c2 | c3 | ...
+ +-----+-----+-----+-----+-----+---
+
+9.6. DHCP Message Type
+
+ This option is used to convey the type of the DHCP message. The code
+ for this option is 53, and its length is 1. Legal values for this
+ option are:
+
+ Value Message Type
+ ----- ------------
+ 1 DHCPDISCOVER
+ 2 DHCPOFFER
+ 3 DHCPREQUEST
+ 4 DHCPDECLINE
+ 5 DHCPACK
+ 6 DHCPNAK
+ 7 DHCPRELEASE
+ 8 DHCPINFORM
+
+ Code Len Type
+ +-----+-----+-----+
+ | 53 | 1 | 1-9 |
+ +-----+-----+-----+
+
+9.7. Server Identifier
+
+ This option is used in DHCPOFFER and DHCPREQUEST messages, and may
+ optionally be included in the DHCPACK and DHCPNAK messages. DHCP
+ servers include this option in the DHCPOFFER in order to allow the
+ client to distinguish between lease offers. DHCP clients use the
+ contents of the 'server identifier' field as the destination address
+ for any DHCP messages unicast to the DHCP server. DHCP clients also
+ indicate which of several lease offers is being accepted by including
+ this option in a DHCPREQUEST message.
+
+ The identifier is the IP address of the selected server.
+
+ The code for this option is 54, and its length is 4.
+
+
+
+Alexander & Droms Standards Track [Page 27]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ Code Len Address
+ +-----+-----+-----+-----+-----+-----+
+ | 54 | 4 | a1 | a2 | a3 | a4 |
+ +-----+-----+-----+-----+-----+-----+
+
+9.8. Parameter Request List
+
+ This option is used by a DHCP client to request values for specified
+ configuration parameters. The list of requested parameters is
+ specified as n octets, where each octet is a valid DHCP option code
+ as defined in this document.
+
+ The client MAY list the options in order of preference. The DHCP
+ server is not required to return the options in the requested order,
+ but MUST try to insert the requested options in the order requested
+ by the client.
+
+ The code for this option is 55. Its minimum length is 1.
+
+ Code Len Option Codes
+ +-----+-----+-----+-----+---
+ | 55 | n | c1 | c2 | ...
+ +-----+-----+-----+-----+---
+
+9.9. Message
+
+ This option is used by a DHCP server to provide an error message to a
+ DHCP client in a DHCPNAK message in the event of a failure. A client
+ may use this option in a DHCPDECLINE message to indicate the why the
+ client declined the offered parameters. The message consists of n
+ octets of NVT ASCII text, which the client may display on an
+ available output device.
+
+ The code for this option is 56 and its minimum length is 1.
+
+ Code Len Text
+ +-----+-----+-----+-----+---
+ | 56 | n | c1 | c2 | ...
+ +-----+-----+-----+-----+---
+
+9.10. Maximum DHCP Message Size
+
+ This option specifies the maximum length DHCP message that it is
+ willing to accept. The length is specified as an unsigned 16-bit
+ integer. A client may use the maximum DHCP message size option in
+ DHCPDISCOVER or DHCPREQUEST messages, but should not use the option
+ in DHCPDECLINE messages.
+
+
+
+
+Alexander & Droms Standards Track [Page 28]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ The code for this option is 57, and its length is 2. The minimum
+ legal value is 576 octets.
+
+ Code Len Length
+ +-----+-----+-----+-----+
+ | 57 | 2 | l1 | l2 |
+ +-----+-----+-----+-----+
+
+9.11. Renewal (T1) Time Value
+
+ This option specifies the time interval from address assignment until
+ the client transitions to the RENEWING state.
+
+ The value is in units of seconds, and is specified as a 32-bit
+ unsigned integer.
+
+ The code for this option is 58, and its length is 4.
+
+ Code Len T1 Interval
+ +-----+-----+-----+-----+-----+-----+
+ | 58 | 4 | t1 | t2 | t3 | t4 |
+ +-----+-----+-----+-----+-----+-----+
+
+9.12. Rebinding (T2) Time Value
+
+ This option specifies the time interval from address assignment until
+ the client transitions to the REBINDING state.
+
+ The value is in units of seconds, and is specified as a 32-bit
+ unsigned integer.
+
+ The code for this option is 59, and its length is 4.
+
+ Code Len T2 Interval
+ +-----+-----+-----+-----+-----+-----+
+ | 59 | 4 | t1 | t2 | t3 | t4 |
+ +-----+-----+-----+-----+-----+-----+
+
+9.13. Vendor class identifier
+
+ This option is used by DHCP clients to optionally identify the vendor
+ type and configuration of a DHCP client. The information is a string
+ of n octets, interpreted by servers. Vendors may choose to define
+ specific vendor class identifiers to convey particular configuration
+ or other identification information about a client. For example, the
+ identifier may encode the client's hardware configuration. Servers
+ not equipped to interpret the class-specific information sent by a
+ client MUST ignore it (although it may be reported). Servers that
+
+
+
+Alexander & Droms Standards Track [Page 29]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ respond SHOULD only use option 43 to return the vendor-specific
+ information to the client.
+
+ The code for this option is 60, and its minimum length is 1.
+
+ Code Len Vendor class Identifier
+ +-----+-----+-----+-----+---
+ | 60 | n | i1 | i2 | ...
+ +-----+-----+-----+-----+---
+
+9.14. Client-identifier
+
+ This option is used by DHCP clients to specify their unique
+ identifier. DHCP servers use this value to index their database of
+ address bindings. This value is expected to be unique for all
+ clients in an administrative domain.
+
+ Identifiers SHOULD be treated as opaque objects by DHCP servers.
+
+ The client identifier MAY consist of type-value pairs similar to the
+ 'htype'/'chaddr' fields defined in [3]. For instance, it MAY consist
+ of a hardware type and hardware address. In this case the type field
+ SHOULD be one of the ARP hardware types defined in STD2 [22]. A
+ hardware type of 0 (zero) should be used when the value field
+ contains an identifier other than a hardware address (e.g. a fully
+ qualified domain name).
+
+ For correct identification of clients, each client's client-
+ identifier MUST be unique among the client-identifiers used on the
+ subnet to which the client is attached. Vendors and system
+ administrators are responsible for choosing client-identifiers that
+ meet this requirement for uniqueness.
+
+ The code for this option is 61, and its minimum length is 2.
+
+ Code Len Type Client-Identifier
+ +-----+-----+-----+-----+-----+---
+ | 61 | n | t1 | i1 | i2 | ...
+ +-----+-----+-----+-----+-----+---
+
+
+
+
+
+
+
+
+
+
+
+
+Alexander & Droms Standards Track [Page 30]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+10. Defining new extensions
+
+ The author of a new DHCP option will follow these steps to obtain
+ acceptance of the option as a part of the DHCP Internet Standard:
+
+ 1. The author devises the new option.
+ 2. The author requests a number for the new option from IANA by
+ contacting:
+ Internet Assigned Numbers Authority (IANA)
+ USC/Information Sciences Institute
+ 4676 Admiralty Way
+ Marina del Rey, California 90292-6695
+
+ or by email as: iana@iana.org
+
+ 3. The author documents the new option, using the newly obtained
+ option number, as an Internet Draft.
+ 4. The author submits the Internet Draft for review through the IETF
+ standards process as defined in "Internet Official Protocol
+ Standards" (STD 1). The new option will be submitted for eventual
+ acceptance as an Internet Standard.
+ 5. The new option progresses through the IETF standards process; the
+ new option will be reviewed by the Dynamic Host Configuration
+ Working Group (if that group still exists), or as an Internet
+ Draft not submitted by an IETF working group.
+ 6. If the new option fails to gain acceptance as an Internet
+ Standard, the assigned option number will be returned to IANA for
+ reassignment.
+
+ This procedure for defining new extensions will ensure that:
+
+ * allocation of new option numbers is coordinated from a single
+ authority,
+ * new options are reviewed for technical correctness and
+ appropriateness, and
+ * documentation for new options is complete and published.
+
+11. Acknowledgements
+
+ The author thanks the many (and too numerous to mention!) members of
+ the DHC WG for their tireless and ongoing efforts in the development
+ of DHCP and this document.
+
+ The efforts of J Allard, Mike Carney, Dave Lapp, Fred Lien and John
+ Mendonca in organizing DHCP interoperability testing sessions are
+ gratefully acknowledged.
+
+
+
+
+
+Alexander & Droms Standards Track [Page 31]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ The development of this document was supported in part by grants from
+ the Corporation for National Research Initiatives (CNRI), Bucknell
+ University and Sun Microsystems.
+
+12. References
+
+ [1] Droms, R., "Dynamic Host Configuration Protocol", RFC 2131,
+ Bucknell University, March 1997.
+
+ [2] Reynolds, J., "BOOTP Vendor Information Extensions", RFC 1497,
+ USC/Information Sciences Institute, August 1993.
+
+ [3] Croft, W., and J. Gilmore, "Bootstrap Protocol", RFC 951,
+ Stanford University and Sun Microsystems, September 1985.
+
+ [4] Braden, R., Editor, "Requirements for Internet Hosts -
+ Communication Layers", STD 3, RFC 1122, USC/Information Sciences
+ Institute, October 1989.
+
+ [5] Mogul, J., and J. Postel, "Internet Standard Subnetting
+ Procedure", STD 5, RFC 950, USC/Information Sciences Institute,
+ August 1985.
+
+ [6] Postel, J., and K. Harrenstien, "Time Protocol", STD 26, RFC
+ 868, USC/Information Sciences Institute, SRI, May 1983.
+
+ [7] Postel, J., "Name Server", IEN 116, USC/Information Sciences
+ Institute, August 1979.
+
+ [8] Mockapetris, P., "Domain Names - Implementation and
+ Specification", STD 13, RFC 1035, USC/Information Sciences
+ Institute, November 1987.
+
+ [9] Postel, J., "Quote of the Day Protocol", STD 23, RFC 865,
+ USC/Information Sciences Institute, May 1983.
+
+ [10] McLaughlin, L., "Line Printer Daemon Protocol", RFC 1179, The
+ Wollongong Group, August 1990.
+
+ [11] Accetta, M., "Resource Location Protocol", RFC 887, CMU,
+ December 1983.
+
+ [12] Mogul, J. and S. Deering, "Path MTU Discovery", RFC 1191,
+ DECWRL, Stanford University, November 1990.
+
+ [13] Deering, S., "ICMP Router Discovery Messages", RFC 1256,
+ Xerox PARC, September 1991.
+
+
+
+
+Alexander & Droms Standards Track [Page 32]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+ [14] Leffler, S. and M. Karels, "Trailer Encapsulations", RFC 893,
+ U. C. Berkeley, April 1984.
+
+ [15] Hornig, C., "Standard for the Transmission of IP Datagrams over
+ Ethernet Networks", RFC 894, Symbolics, April 1984.
+
+ [16] Postel, J. and J. Reynolds, "Standard for the Transmission of
+ IP Datagrams Over IEEE 802 Networks", RFC 1042, USC/Information
+ Sciences Institute, February 1988.
+
+ [17] Sun Microsystems, "System and Network Administration", March
+ 1990.
+
+ [18] Mills, D., "Internet Time Synchronization: The Network Time
+ Protocol", RFC 1305, UDEL, March 1992.
+
+ [19] NetBIOS Working Group, "Protocol Standard for a NetBIOS Service
+ on a TCP/UDP transport: Concepts and Methods", STD 19, RFC 1001,
+ March 1987.
+
+ [20] NetBIOS Working Group, "Protocol Standard for a NetBIOS Service
+ on a TCP/UDP transport: Detailed Specifications", STD 19, RFC
+ 1002, March 1987.
+
+ [21] Scheifler, R., "FYI On the X Window System", FYI 6, RFC 1198,
+ MIT Laboratory for Computer Science, January 1991.
+
+ [22] Reynolds, J., and J. Postel, "Assigned Numbers", STD 2, RFC 1700,
+ USC/Information Sciences Institute, July 1992.
+
+13. Security Considerations
+
+ Security issues are not discussed in this memo.
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+Alexander & Droms Standards Track [Page 33]
+
+RFC 2132 DHCP Options and BOOTP Vendor Extensions March 1997
+
+
+14. Authors' Addresses
+
+ Steve Alexander
+ Silicon Graphics, Inc.
+ 2011 N. Shoreline Boulevard
+ Mailstop 510
+ Mountain View, CA 94043-1389
+
+ Phone: (415) 933-6172
+ EMail: sca@engr.sgi.com
+
+
+ Ralph Droms
+ Bucknell University
+ Lewisburg, PA 17837
+
+ Phone: (717) 524-1145
+ EMail: droms@bucknell.edu
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+Alexander & Droms Standards Track [Page 34]
+