summaryrefslogtreecommitdiff
path: root/doc/rfc/rfc6519.txt
diff options
context:
space:
mode:
Diffstat (limited to 'doc/rfc/rfc6519.txt')
-rw-r--r--doc/rfc/rfc6519.txt619
1 files changed, 619 insertions, 0 deletions
diff --git a/doc/rfc/rfc6519.txt b/doc/rfc/rfc6519.txt
new file mode 100644
index 0000000..2f29ee4
--- /dev/null
+++ b/doc/rfc/rfc6519.txt
@@ -0,0 +1,619 @@
+
+
+
+
+
+
+Internet Engineering Task Force (IETF) R. Maglione
+Request for Comments: 6519 Telecom Italia
+Category: Standards Track A. Durand
+ISSN: 2070-1721 Juniper Networks
+ February 2012
+
+
+ RADIUS Extensions for Dual-Stack Lite
+
+Abstract
+
+ Dual-Stack Lite is a solution to offer both IPv4 and IPv6
+ connectivity to customers that are addressed only with an IPv6
+ prefix. Dual-Stack Lite requires pre-configuration of the Dual-Stack
+ Lite Address Family Transition Router (AFTR) tunnel information on
+ the Basic Bridging BroadBand (B4) element. In many networks, the
+ customer profile information may be stored in Authentication,
+ Authorization, and Accounting (AAA) servers, while client
+ configurations are mainly provided through the Dynamic Host
+ Configuration Protocol (DHCP). This document specifies a new Remote
+ Authentication Dial-In User Service (RADIUS) attribute to carry the
+ Dual-Stack Lite AFTR tunnel name; the RADIUS attribute is defined
+ based on the equivalent DHCPv6 OPTION_AFTR_NAME option. This RADIUS
+ attribute is meant to be used between the RADIUS server and the
+ Network Access Server (NAS); it is not intended to be used directly
+ between the B4 element and the RADIUS server.
+
+Status of This Memo
+
+ This is an Internet Standards Track document.
+
+ This document is a product of the Internet Engineering Task Force
+ (IETF). It represents the consensus of the IETF community. It has
+ received public review and has been approved for publication by the
+ Internet Engineering Steering Group (IESG). Further information on
+ Internet Standards is available in Section 2 of RFC 5741.
+
+ Information about the current status of this document, any errata,
+ and how to provide feedback on it may be obtained at
+ http://www.rfc-editor.org/info/rfc6519.
+
+
+
+
+
+
+
+
+
+
+
+Maglione & Durand Standards Track [Page 1]
+
+RFC 6519 DS-Lite RADIUS Extensions February 2012
+
+
+Copyright Notice
+
+ Copyright (c) 2012 IETF Trust and the persons identified as the
+ document authors. All rights reserved.
+
+ This document is subject to BCP 78 and the IETF Trust's Legal
+ Provisions Relating to IETF Documents
+ (http://trustee.ietf.org/license-info) in effect on the date of
+ publication of this document. Please review these documents
+ carefully, as they describe your rights and restrictions with respect
+ to this document. Code Components extracted from this document must
+ include Simplified BSD License text as described in Section 4.e of
+ the Trust Legal Provisions and are provided without warranty as
+ described in the Simplified BSD License.
+
+ This document may contain material from IETF Documents or IETF
+ Contributions published or made publicly available before November
+ 10, 2008. The person(s) controlling the copyright in some of this
+ material may not have granted the IETF Trust the right to allow
+ modifications of such material outside the IETF Standards Process.
+ Without obtaining an adequate license from the person(s) controlling
+ the copyright in such materials, this document may not be modified
+ outside the IETF Standards Process, and derivative works of it may
+ not be created outside the IETF Standards Process, except to format
+ it for publication as an RFC or to translate it into languages other
+ than English.
+
+Table of Contents
+
+ 1. Introduction ....................................................3
+ 2. Terminology .....................................................4
+ 3. DS-Lite Configuration with RADIUS and DHCPv6 ....................4
+ 4. RADIUS Attribute ................................................7
+ 4.1. DS-Lite-Tunnel-Name ........................................7
+ 5. Table of Attributes .............................................9
+ 6. Security Considerations .........................................9
+ 7. IANA Considerations .............................................9
+ 8. References .....................................................10
+ 8.1. Normative References ......................................10
+ 8.2. Informative References ....................................10
+
+
+
+
+
+
+
+
+
+
+
+Maglione & Durand Standards Track [Page 2]
+
+RFC 6519 DS-Lite RADIUS Extensions February 2012
+
+
+1. Introduction
+
+ Dual-Stack Lite [RFC6333] is a solution to offer both IPv4 and IPv6
+ connectivity to customers that are addressed only with an IPv6 prefix
+ (no IPv4 address is assigned to the attachment device). One of its
+ key components is an IPv4-over-IPv6 tunnel, but a Dual-Stack-Lite
+ Basic Bridging BroadBand (B4) element will not know if the network to
+ which it is attached offers Dual-Stack Lite support. Even if the B4
+ did know, it would not know the remote end of the tunnel to which it
+ could establish a connection.
+
+ To inform the B4 element of the location of the Address Family
+ Transition Router (AFTR), a Fully Qualified Domain Name (FQDN) may be
+ used. Once this information is conveyed, the presence of the
+ configuration indicating the AFTR's location also informs a host to
+ initiate Dual-Stack Lite (DS-Lite) service and become a Softwire
+ Initiator.
+
+ [RFC6334] specifies a DHCPv6 option that is meant to be used by a
+ DS-Lite client (B4 element) to discover its AFTR name. In order to
+ be able to populate such an option, the DHCPv6 server must be
+ pre-provisioned with the AFTR name.
+
+ In broadband environments, a customer profile may be managed by
+ Authentication, Authorization, and Accounting (AAA) servers, together
+ with AAA for users. The Remote Authentication Dial-In User Service
+ (RADIUS) protocol [RFC2865] is usually used by AAA servers to
+ communicate with network elements. [RADIUS-IPv6] describes a typical
+ broadband network scenario in which the Network Access Server (NAS)
+ acts as the access gateway for the users (hosts or Customer Premises
+ Equipment (CPE) devices) and also embeds a DHCPv6 server function
+ that allows it to locally handle any DHCPv6 requests issued by the
+ clients.
+
+ Since the DS-Lite AFTR information can be stored in AAA servers and
+ the client configuration is mainly provided through DHCP running
+ between the NAS and the requesting clients, a new RADIUS attribute is
+ needed to send AFTR information from the AAA server to the NAS.
+
+ This document defines a new RADIUS attribute to be used for carrying
+ the DS-Lite Tunnel Name, based on the equivalent DHCPv6 option
+ already specified in [RFC6334].
+
+
+
+
+
+
+
+
+
+Maglione & Durand Standards Track [Page 3]
+
+RFC 6519 DS-Lite RADIUS Extensions February 2012
+
+
+2. Terminology
+
+ The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
+ "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
+ document are to be interpreted as described in [RFC2119].
+
+ The terms DS-Lite Basic Bridging BroadBand element (B4) and the
+ DS-Lite Address Family Transition Router element (AFTR) are defined
+ in [RFC6333].
+
+3. DS-Lite Configuration with RADIUS and DHCPv6
+
+ Figure 1 illustrates how the RADIUS protocol and DHCPv6 work together
+ to accomplish DS-Lite configuration on the B4 element when a PPP
+ session is used to provide connectivity to the user.
+
+ The NAS operates as a client of RADIUS and as a DHCP Server. The NAS
+ initially sends a RADIUS Access-Request message to the RADIUS server,
+ requesting authentication. Once the RADIUS server receives the
+ request, it validates the sending client, and if the request is
+ approved, the AAA server replies with an Access-Accept message
+ including a list of attribute-value pairs that describe the
+ parameters to be used for this session. This list MAY also contain
+ the AFTR tunnel name. When the NAS receives a DHCPv6 client request
+ containing the DS-Lite tunnel option, the NAS SHALL use the name
+ returned in the RADIUS DS-Lite-Tunnel-Name attribute to populate the
+ DHCPv6 OPTION_AFTR_NAME option in the DHCPv6 reply message.
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+Maglione & Durand Standards Track [Page 4]
+
+RFC 6519 DS-Lite RADIUS Extensions February 2012
+
+
+ B4 NAS AAA
+ | | Server
+ | | |
+ |----PPP LCP Config-Request------> | |
+ | | |
+ | |----Access-Request ---->|
+ | | |
+ | |<---- Access-Accept-----|
+ | | (DS-Lite-Tunnel-Name) |
+ |<-----PPP LCP Config-ACK ------- | |
+ | | |
+ | | |
+ |--- PPP IPv6CP Config-Request --->| |
+ | | |
+ |<----- PPP IPv6CP Config-ACK -----| |
+ | | |
+ |------- DHCPv6 Solicit -------->| |
+ | | |
+ |<-------DHCPv6 Advertisement -----| |
+ | (DHCPv6 OPTION_AFTR_NAME) | |
+ | | |
+ |------- DHCPv6 Request -------->| |
+ | | |
+ |<-------- DHCPv6 Reply ---------- | |
+ | (DHCPv6 OPTION_AFTR_NAME) | |
+
+ DHCPv6 RADIUS
+
+ Figure 1: RADIUS and DHCPv6 Message Flow for a PPP Session
+
+ Figure 2 illustrates how the RADIUS protocol and DHCPv6 work together
+ to accomplish DS-Lite configuration on the B4 element when an IP
+ session is used to provide connectivity to the user.
+
+ The only difference between this message flow and the previous one is
+ that in this scenario, the interaction between the NAS and the AAA/
+ RADIUS server is triggered by the DHCPv6 Solicit message received by
+ the NAS from the B4 acting as a DHCPv6 client, while in the case of a
+ PPP session, the trigger is the PPP Link Control Protocol (LCP)
+ Config-Request message received by the NAS.
+
+
+
+
+
+
+
+
+
+
+
+Maglione & Durand Standards Track [Page 5]
+
+RFC 6519 DS-Lite RADIUS Extensions February 2012
+
+
+ B4 NAS AAA
+ | | Server
+ |------ DHCPv6 Solicit ---------> | |
+ | | |
+ | |----Access-Request ---->|
+ | | |
+ | |<---Access-Accept-------|
+ | | (DS-Lite-Tunnel-Name) |
+ | | |
+ |<-------DHCPv6 Advertisement------| |
+ | (DHCPv6 OPTION_AFTR_NAME) | |
+ | | |
+ |------- DHCPv6 Request -------->| |
+ | | |
+ | | |
+ |<----- DHCPv6 Reply ------------- | |
+ | (DHCPv6 OPTION_AFTR_NAME) | |
+
+ DHCPv6 RADIUS
+
+ Figure 2: RADIUS and DHCPv6 Message Flow for an IP Session
+
+ In the scenario depicted in Figure 2, the Access-Request packet
+ contains a Service-Type attribute with the value Authorize Only (17);
+ thus, according to [RFC5080], the Access-Request packet MUST contain
+ a State attribute.
+
+ After receiving the DS-Lite-Tunnel-Name attribute in the initial
+ Access-Accept packet, the NAS MUST store the received AFTR tunnel
+ name locally. When the B4 sends a DHCPv6 Renew message to request an
+ extension of the lifetimes for the assigned address or prefix, the
+ NAS does not have to initiate a new Access-Request packet towards the
+ AAA server to request the AFTR tunnel name. The NAS retrieves the
+ previously stored AFTR tunnel name and uses it in its reply.
+
+ According to [RFC3315], if the DHCPv6 server to which the DHCPv6
+ Renew message was sent at time T1 has not responded, the DHCPv6
+ client initiates a Rebind/Reply message exchange with any available
+ server. In this scenario, the NAS receiving the DHCPv6 Rebind
+ message MUST initiate a new Access-Request message towards the AAA
+ server. The NAS MAY include the DS-Lite-Tunnel-Name attribute in its
+ Access-Request message.
+
+ If the NAS does not receive the DS-Lite-Tunnel-Name attribute in the
+ Access-Accept message, it MAY fall back to a pre-configured default
+ tunnel name, if any. If the NAS does not have any pre-configured
+
+
+
+
+
+Maglione & Durand Standards Track [Page 6]
+
+RFC 6519 DS-Lite RADIUS Extensions February 2012
+
+
+ default tunnel name or if the NAS receives an Access-Reject message,
+ the IPv4-over-IPv6 tunnel cannot be established; thus, the B4 element
+ has only IPv6 connectivity.
+
+4. RADIUS Attribute
+
+ This section specifies the format of the new RADIUS attribute.
+
+4.1. DS-Lite-Tunnel-Name
+
+ The DS-Lite-Tunnel-Name RADIUS attribute contains an FQDN that refers
+ to the AFTR to which the client is requested to establish a
+ connection. The NAS SHALL use the name returned in the RADIUS
+ DS-Lite-Tunnel-Name attribute to populate the DHCPv6 OPTION_AFTR_NAME
+ option [RFC6334].
+
+ This attribute MAY be used in Access-Request packets as a hint to the
+ RADIUS server; for example, if the NAS is pre-configured with a
+ default tunnel name, this name MAY be inserted in the attribute. The
+ RADIUS server MAY ignore the hint sent by the NAS, and it MAY assign
+ a different AFTR tunnel name.
+
+ If the NAS includes the DS-Lite-Tunnel-Name attribute, but the AAA
+ server does not recognize it, this attribute MUST be ignored by the
+ AAA server.
+
+ If the NAS does not receive the DS-Lite-Tunnel-Name attribute in the
+ Access-Accept message, it MAY fall back to a pre-configured default
+ tunnel name, if any. If the NAS does not have any pre-configured
+ default tunnel name, the tunnel cannot be established.
+
+ If the NAS is pre-provisioned with a default AFTR tunnel name and the
+ AFTR tunnel name received in the Access-Accept message is different
+ from the configured default, then the AFTR tunnel name received in
+ the Access-Accept message MUST be used for the session.
+
+ If the NAS cannot support the received AFTR tunnel name for any
+ reason, the tunnel SHOULD NOT be established.
+
+ When the Access-Request message is triggered by a DHCPv6 Rebind
+ message, if the AFTR tunnel name received in the Access-Accept
+ message is different from the currently used one for that session,
+ the NAS MUST force the B4 to re-establish the tunnel using the new
+ AFTR name received in the Access-Accept message.
+
+ If an implementation includes Change-of-Authorization (CoA) messages
+ [RFC5176], they could be used to modify the current established
+ DS-Lite tunnel. When the NAS receives a CoA Request message
+
+
+
+Maglione & Durand Standards Track [Page 7]
+
+RFC 6519 DS-Lite RADIUS Extensions February 2012
+
+
+ containing the DS-Lite-Tunnel-Name attribute, the NAS MUST send a
+ Reconfigure message to a B4 to inform the B4 that the NAS has new or
+ updated configuration parameters and that the B4 is to initiate a
+ Renew/Reply or Information-Request/Reply transaction with the NAS in
+ order to receive the updated information.
+
+ Upon receiving an AFTR tunnel name different from the currently used
+ one, the B4 MUST terminate the current DS-Lite tunnel, and the B4
+ MUST establish a new DS-Lite tunnel with the specified AFTR.
+
+ The DS-Lite-Tunnel-Name RADIUS attribute MAY be present in
+ Accounting-Request records where the Acct-Status-Type is set to
+ Start, Stop, or Interim-Update. The DS-Lite-Tunnel-Name RADIUS
+ attribute MUST NOT appear more than once in a message.
+
+ A summary of the DS-Lite-Tunnel-Name RADIUS attribute format is shown
+ below. The fields are transmitted from left to right.
+
+ 0 1 2 3
+ 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
+ | Type | Length | DS-Lite-Tunnel-Name (FQDN)...
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
+
+ Type:
+
+ 144 for DS-Lite-Tunnel-Name.
+
+ Length:
+
+ This field indicates the total length in octets of this
+ attribute including the Type and Length fields, and the length
+ in octets of the DS-Lite-Tunnel-Name field.
+
+ DS-Lite-Tunnel-Name:
+
+ This field contains a single FQDN of the remote tunnel endpoint,
+ located at the DS-Lite AFTR.
+
+ As the DS-Lite-Tunnel-Name attribute is used to populate the DHCPv6
+ OPTION_AFTR_NAME option, the DS-Lite-Tunnel-Name field is formatted
+ as required in DHCPv6 (Section 8 of [RFC3315] -- "Representation and
+ Use of Domain Names"). Briefly, the format described is using a
+ single octet noting the length of one DNS label (limited to at most
+ 63 octets), followed by the label contents. This repeats until all
+ labels in the FQDN are exhausted, including a terminating zero-length
+ label. Any updates to Section 8 of [RFC3315] also apply to the
+ encoding of this field.
+
+
+
+Maglione & Durand Standards Track [Page 8]
+
+RFC 6519 DS-Lite RADIUS Extensions February 2012
+
+
+ The data type of the DS-Lite-Tunnel-Name RADIUS attribute is a string
+ with opaque encapsulation, according to Section 5 of [RFC2865].
+
+5. Table of Attributes
+
+ The following tables provide a guide to which attributes may be found
+ in which kinds of packets, and in what quantity.
+
+ Access- Access- Access- Challenge Accounting # Attribute
+ Request Accept Reject Request
+ 0-1 0-1 0 0 0-1 144 DS-Lite-Tunnel-Name
+
+ CoA-Request CoA-ACK CoA-NACK # Attribute
+ 0-1 0 0 144 DS-Lite-Tunnel-Name
+
+ The following table defines the meaning of the above table entries.
+
+ 0 This attribute MUST NOT be present in the packet.
+ 0+ Zero or more instances of this attribute MAY be present in the
+ packet.
+ 0-1 Zero or one instance of this attribute MAY be present in the
+ packet.
+
+6. Security Considerations
+
+ This document has no additional security considerations beyond those
+ already identified in [RFC2865] for the RADIUS protocol and in
+ [RFC5176] for CoA messages.
+
+ [RFC6333] discusses security issues related to Dual-Stack Lite.
+
+7. IANA Considerations
+
+ Per this document, IANA has allocated a new RADIUS attribute type
+ from the IANA registry "Radius Attribute Types" located at
+ http://www.iana.org/assignments/radius-types.
+
+ DS-Lite-Tunnel-Name - 144
+
+
+
+
+
+
+
+
+
+
+
+
+
+Maglione & Durand Standards Track [Page 9]
+
+RFC 6519 DS-Lite RADIUS Extensions February 2012
+
+
+8. References
+
+8.1. Normative References
+
+ [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
+ Requirement Levels", BCP 14, RFC 2119, March 1997.
+
+ [RFC2865] Rigney, C., Willens, S., Rubens, A., and W. Simpson,
+ "Remote Authentication Dial In User Service (RADIUS)",
+ RFC 2865, June 2000.
+
+ [RFC3315] Droms, R., Ed., Bound, J., Volz, B., Lemon, T.,
+ Perkins, C., and M. Carney, "Dynamic Host
+ Configuration Protocol for IPv6 (DHCPv6)", RFC 3315,
+ July 2003.
+
+ [RFC5080] Nelson, D. and A. DeKok, "Common Remote Authentication
+ Dial In User Service (RADIUS) Implementation Issues
+ and Suggested Fixes", RFC 5080, December 2007.
+
+ [RFC6333] Durand, A., Droms, R., Woodyatt, J., and Y. Lee,
+ "Dual-Stack Lite Broadband Deployments Following IPv4
+ Exhaustion", RFC 6333, August 2011.
+
+ [RFC6334] Hankins, D. and T. Mrugalski, "Dynamic Host
+ Configuration Protocol for IPv6 (DHCPv6) Option for
+ Dual-Stack Lite", RFC 6334, August 2011.
+
+8.2. Informative References
+
+ [RADIUS-IPv6] Lourdelet, B., Dec, W., Ed., Sarikaya, B., Zorn, G.,
+ and D. Miles, "RADIUS attributes for IPv6 Access
+ Networks", Work in Progress, November 2011.
+
+ [RFC5176] Chiba, M., Dommety, G., Eklund, M., Mitton, D., and B.
+ Aboba, "Dynamic Authorization Extensions to Remote
+ Authentication Dial In User Service (RADIUS)",
+ RFC 5176, January 2008.
+
+
+
+
+
+
+
+
+
+
+
+
+
+Maglione & Durand Standards Track [Page 10]
+
+RFC 6519 DS-Lite RADIUS Extensions February 2012
+
+
+Authors' Addresses
+
+ Roberta Maglione
+ Telecom Italia
+ Via Reiss Romoli 274
+ Torino 10148
+ Italy
+
+ EMail: roberta.maglione@telecomitalia.it
+
+
+ Alain Durand
+ Juniper Networks
+ 1194 North Mathilda Avenue
+ Sunnyvale, CA 94089-1206
+ USA
+
+ EMail: adurand@juniper.net
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+Maglione & Durand Standards Track [Page 11]
+