1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
|
Network Working Group W. Hathaway
Request for Comments: 135 AMES
NIC: 6712 29 April 1971
Updates: 110
Response to NWG/RFC #110
(Conventions for Using an IBM 2741 Terminal as a User Console for
Access to Network Server Hosts)
I would like to propose the following conventions to replace the ones
proposed in RFC #110. The original conventions suffer from lack of
consideration of the correspondence 2741 and what I feel are
inconsistencies and considerable difficulty of use. (The 2741
terminal with correspondence keyboard does not have all of the
standard characters, notably:
less than <
greater than >
logical not [1]
vertical bar |
Thus we must not use any of these characters in our conventions if we
wish to support the correspondence 2741.)
The dedication of certain characters to special functions involves a
trade-off: the convenience of having the function as a single key
versus the inconvenience of having to use two keys to enter the
character as data. I believe that only two of the special functions
listed in RFC #110 justify the dedication of a key: the "character
escape" function and the "character delete" function. For the
"character escape" function I recommend the cent sign [2], as this
character is on both the regular and correspondence 2741 terminals
and is not in the ASCII character set. For the "character delete"
function I recommend the backspace key for obvious reasons. While
there is some need to be able to enter the character "backspace" (as
for underscoring output etc.,) I feel that the trade-off mentioned
above clearly indicates a single key "character delete" would be much
more valuable than a single key "backspace" and a two key "character
delete."
For the other special functions I recommend two key combinations,
consisting of "character escape" [2] and a key to define the
function. These are summarized below:
Hathaway [Page 1]
^L
RFC 135 Response to NWG/RFC #110 29 April 1971
character escape [2]
character delete backspace
system delete [2]$
line delete [2]# or [2]#NL
logical line end [2];
line continuation [2]NL
ASCII control [2]@
The option in "line delete" is to allow the user to enter a new line
(NL) immediately after the "line delete" to line up margins without
entering a null line; to enter a null line after a "line delete"
would require two NL characters.
The two new functions defined above, "line continuation" and "ASCII
control," are used as follows. The "line continuation" is used to
enter a line which is longer than the 2741 carriage (or the margin
placement) will permit. It can be looked on as the complement of the
"logical line end" in that is allows you to enter one logical line on
several physical lines.
The use of the "ASCII control" function requires some background.
There are of course many characters in ASCII which are keyed as
combinations of "control" and another key. The "character escape"
function may be used to handle these control characters as follows: a
"character escape" followed by a letter will be the equivalent of the
ASCII "control" "letter", written as Xc (where X is the letter).
This will greatly simplify the conventions for users, as they will
simply key "[2]A" where they are used to using Ac and so forth. For
completeness, however, there needs to be a way to key the additional
control characters which require both "control" and "shift" in
addition to a letter (such as ESC, which is SHIFT Mc). Further it is
desirable that a more mnemonic system be provided for the non-
Teletype user, who knows he wants a LF but does not know that it is a
Jc. To satisfy both of these needs I recommend the "ASCII control"
special function, which is used to enter any of the ASCII control
character as "[2]@" followed by the standard two or three character
abbreviation. Thus "escape" would be [2]@ESC, "line feed" would be
[2]@LF, and so forth. The use of the variable length abbreviation
does not introduce any ambiguity, although from an implementation
standpoint it may be advantageous to use the two character
abbreviation proposed in RFC #110.
Finally we must be able to enter the eight ASCII graphics which do
not appear on either 2741 terminal, as well as the "cent sign" and
"backspace" themselves (without their special functions). For these
I recommend the following:
Hathaway [Page 2]
^L
RFC 135 Response to NWG/RFC #110 29 April 1971
[2]( for [
[2]) for ]
[2]6 for {
[2]9 for }
[2]/ for \
[2]' for '
[2]" for ^
[2]- for ~
[2][2] for [2]
[2]backspace for backspace
Note that the characters "<" and ">" do not appear on the
correspondence 2741 and hence should not be used.
Endnotes
[1] logical not
[2] cent sign
[This RFC was put into machine readable form for entry]
[into the online RFC archives by Lorrie Shiota, 10/02]
Hathaway [Page 3]
^L
|
