1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
|
Network Working Group K. Alagappan
Request for Comments: 1412 Digital Equipment Corporation
January 1993
Telnet Authentication: SPX
Status of this Memo
This memo defines an Experimental Protocol for the Internet
community. Discussion and suggestions for improvement are requested.
Please refer to the current edition of the "IAB Official Protocol
Standards" for the standardization state and status of this protocol.
Distribution of this memo is unlimited.
1. Command Names and Codes
Authentication Types
SPX 3
Suboption Commands
AUTH 0
REJECT 1
ACCEPT 2
2. Command Meanings
IAC SB AUTHENTICATION IS <authentication-type-pair> AUTH
<SPX authentication token> IAC SE
This is used to pass the SPX authentication token to the remote
side of the connection. (A document which describes the
authentication token syntax is forthcoming.) The first octet of
the <authentication-type-pair> value is SPX. The second octet is
a modifier to the SPX authentication type.
IAC SB AUTHENTICATION REPLY <authentication-type-pair> ACCEPT
<mutual response> IAC SE
This command indicates that the authentication was successful.
After an SPX authentication exchange, both sides have securely
established a random 8-byte key to be used as the default key for
the ENCRYPTION option. If the AUTH_HOW_MUTUAL bit is set in the
second octet of the authentication-type-pair, the sender includes
the mutual response bytes. The receiver of the ACCEPT command
compares the "mutual response" with its expected mutual response.
Telnet Working Group [Page 1]
^L
RFC 1412 SPX for Telnet January 1993
(A document which describes the mutual response syntax is forth
coming.) If the AUTH_HOW_ONE_WAY bit is set in the second octet
of the authentication-type-pair, the sender includes zero bytes of
mutual response.
IAC SB AUTHENTICATION REPLY <authentication-type-pair> REJECT
<optional reason for rejection> IAC SE
This command indicates that the authentication was not successful,
and if there is any more data in the sub-option, it is an ASCII
text message of the reason for the rejection.
3. Implementation Rules
Every command after the first AUTHENTICATION IS must carry the same
set of modifiers (e.g., CLIENT|MUTUAL) for subsequent AUTHENTICATION
IS and AUTHENTICATION REPLY commands.
If the second octet of the authentication-type-pair has the AUTH_WHO
bit set to AUTH_WHO_CLIENT, then the client sends the initial AUTH
command, and the server responds with either ACCEPT or REJECT.
If the second octet of the authentication-type-pair has the AUTH_WHO
bit set to AUTH_WHO_SERVER, then the server sends the initial AUTH
command, and the client responds with either ACCEPT or REJECT.
4. Examples
User "joe" may wish to log in as user "pete" on machine "foo". If
"pete" has set things up on "foo" to allow "joe" access to his
account, then the client would send IAC SB AUTHENTICATION NAME "pete"
IAC SE IAC SB AUTHENTICATION IS SPX AUTH <joe's spx authentication
token> IAC SE. The server would then authenticate the user as "joe"
from the token information, and the server would send back either
ACCEPT or REJECT. If mutual authentication is being used, the server
would include in the ACCEPT message, a mutual response. The
authorization check to see if "pete" is allowing "joe" to use his
account is made after the authentication exchange is complete.
Therefore, it is possible for the client to receive an ACCEPT
response (based on the authentication token), but for joe to be
denied access to log in to pete's account.
Telnet Working Group [Page 2]
^L
RFC 1412 SPX for Telnet January 1993
Client Server
IAC DO AUTHENTICATION
IAC WILL AUTHENTICATION
[ The server is now free to request authentication information.
]
IAC SB AUTHENTICATION SEND SPX
CLIENT|MUTUAL SPX CLIENT|ONE_WAY
IAC SE
[ The server has requested mutual SPX authentication. If mutual
authentication is not supported, then the server is willing to
do one-way SPX authentication. ]
[ The client will now respond with the name of the user that it
wants to log in as, and the SPX authentication token. ]
IAC SB AUTHENTICATION NAME
"pete" IAC SE
IAC SB AUTHENTICATION IS SPX
CLIENT|MUTUAL AUTH <spx
authentication token
information> IAC SE
[ The server responds with an ACCEPT command to state that the
authentication was successful. ]
[ If AUTH_HOW_MUTUAL, the server responds with the mutual
response so the client can verify that it is really talking to
the right server. ]
[ If AUTH_HOW_ONE_WAY, the server responds with a NULL mutual
response, since the client is willing to trust the server
already. ]
IAC SB AUTHENTICATION REPLY SPX
CLIENT|MUTUAL ACCEPT <mutual
response> IAC SE
Telnet Working Group [Page 3]
^L
RFC 1412 SPX for Telnet January 1993
Security Considerations
The ability to negotiate a common authentication mechanism between
client and server is a feature of the authentication option that
should be used with caution. When the negotiation is performed, no
authentication has yet occurred. Therefore, each system has no way
of knowing whether or not it is talking to the system it intends. An
intruder could attempt to negotiate the use of an authentication
system which is either weak, or already compromised by the intruder.
Author's Address
Kannan Alagappan
Digital Equipment Corporation
550 King Street, LKG1-2/A19
Littleton, MA 01460
EMail: kannan@sejour.lkg.dec.com
Mailing List: telnet-ietf@CRAY.COM
The working group can be contacted via the current chair:
Steve Alexander
INTERACTIVE Systems Corporation
1901 North Naper Boulevard
Naperville, IL 60563-8895
Phone: (708) 505-9100 x256
EMail: stevea@isc.com
Telnet Working Group [Page 4]
^L
|
