path: root/doc/rfc/rfc5012.txt

Network Working Group                                     H. Schulzrinne
Request for Comments: 5012                                   Columbia U.
Category: Informational                                 R. Marshall, Ed.
                                                                     TCS
                                                            January 2008


           Requirements for Emergency Context Resolution with
                         Internet Technologies

Status of This Memo

   This memo provides information for the Internet community.  It does
   not specify an Internet standard of any kind.  Distribution of this
   memo is unlimited.

Abstract

   This document defines terminology and enumerates requirements for the
   context resolution of emergency calls placed by the public using
   voice-over-IP (VoIP) and general Internet multimedia systems, where
   Internet protocols are used end to end.

Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  2
   2.  Requirements Terminology . . . . . . . . . . . . . . . . . . .  3
   3.  Terminology  . . . . . . . . . . . . . . . . . . . . . . . . .  3
     3.1.  Emergency Services . . . . . . . . . . . . . . . . . . . .  3
     3.2.  Service Providers  . . . . . . . . . . . . . . . . . . . .  3
     3.3.  Actors . . . . . . . . . . . . . . . . . . . . . . . . . .  4
     3.4.  Call Routing Entities  . . . . . . . . . . . . . . . . . .  5
     3.5.  Location . . . . . . . . . . . . . . . . . . . . . . . . .  5
     3.6.  Identifiers, Numbers, and Dial Strings . . . . . . . . . .  6
     3.7.  Mapping  . . . . . . . . . . . . . . . . . . . . . . . . .  7
   4.  Basic Actors . . . . . . . . . . . . . . . . . . . . . . . . .  8
   5.  High-Level Requirements  . . . . . . . . . . . . . . . . . . . 10
   6.  Identifying the Caller's Location  . . . . . . . . . . . . . . 12
   7.  Emergency Service Identifier . . . . . . . . . . . . . . . . . 14
   8.  Mapping Protocol . . . . . . . . . . . . . . . . . . . . . . . 16
   9.  Security Considerations  . . . . . . . . . . . . . . . . . . . 20
   10. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 20
   11. Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . 21
   12. References . . . . . . . . . . . . . . . . . . . . . . . . . . 21
     12.1. Normative References . . . . . . . . . . . . . . . . . . . 21
     12.2. Informative References . . . . . . . . . . . . . . . . . . 21





Schulzrinne & Marshall       Informational                      [Page 1]
^L
RFC 5012                   ECRIT Requirements               January 2008


1.  Introduction

   Users of both voice-centric (telephone-like) and non-voice services,
   such as text communication for hearing-disabled users (see [RFC3351]
   and [toip]), expect to be able to initiate a request for help in case
   of an emergency.

   Unfortunately, the existing mechanisms to support emergency calls
   that have evolved within the public circuit-switched telephone
   network (PSTN) are not appropriate to handle evolving IP-based voice,
   text, and real-time multimedia communications.  This document
   outlines the key requirements that IP-based end systems and network
   elements, such as Session Initiation Protocol (SIP) [RFC3261]
   proxies, need to satisfy in order to provide emergency call services,
   which at a minimum, offer the same functionality as existing PSTN
   services, with the additional overall goal of making emergency
   calling more robust, less costly to implement, and multimedia-
   capable.

   This document only focuses on end-to-end IP-based calls, i.e., where
   the emergency call originates from an IP end system and terminates in
   an IP-capable public safety answering point (PSAP), conveyed entirely
   over an IP network.

   We first define terminology in Section 3.  The document then outlines
   various functional issues that relate to placing an IP-based
   emergency call, including a description of baseline requirements
   (Section 5), identification of the emergency caller's location
   (Section 6), use of a service identifier to declare a call to be an
   emergency call (Section 7), and finally, the mapping function
   required to route the call to the appropriate PSAP (Section 8).

   The primary purpose of the mapping protocol is to produce a PSAP URI
   drawn from a preferred set of URI schemes such as SIP or SIPS URIs,
   based on both location information [RFC4119] and a service identifier
   in order to facilitate the IP end-to-end completion of an emergency
   call.

   Aside from obtaining a PSAP URI, the mapping protocol is useful for
   obtaining other information as well.  There may be a case, for
   example, where an appropriate emergency number is not known, only the
   location.  The mapping protocol can then return a geographically
   appropriate emergency number based on the input.








Schulzrinne & Marshall       Informational                      [Page 2]
^L
RFC 5012                   ECRIT Requirements               January 2008


   Since some PSAPs may not immediately support IP, or because some user
   equipment (UE) may not initially support emergency service
   identifiers, it may be necessary to also support emergency service
   identifiers that utilize less-preferred URI schemes, such as a tel
   URI in order to complete an emergency call via the PSTN.

   Identification of the caller, while not incompatible with the
   requirements for messaging outlined within this document, is
   considered to be outside the scope of this document.

   Location is required for two separate purposes: first, to support the
   routing of the emergency call to the appropriate PSAP and second, to
   display the caller's location to the call taker to help in
   dispatching emergency assistance to the appropriate location.

   This latter use, the display of location information to the PSAP, is
   orthogonal to the mapping protocol, and is outside the scope of this
   document.

2.  Requirements Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119],
   with the important qualification that, unless otherwise stated, these
   terms apply to the design of the mapping protocol, not its
   implementation or application.

3.  Terminology

3.1.  Emergency Services

   Basic emergency service:  Basic emergency service allows a caller to
      reach a PSAP serving its current location, but the PSAP may not be
      able to determine the identity or geographic location of the
      caller, except by the call taker asking the caller.

   Enhanced emergency service:  In enhanced emergency service, the PSAP
      call taker can determine the caller's current location.

3.2.  Service Providers

   Internet Access Provider (IAP):  An organization that provides
      physical and data link (layer 2) network connectivity to its
      customers or users, e.g., through digital subscriber lines, cable
      TV plants, Ethernet, leased lines, or radio frequencies.  Examples
      of such organizations include telecommunication carriers,




Schulzrinne & Marshall       Informational                      [Page 3]
^L
RFC 5012                   ECRIT Requirements               January 2008


      municipal utilities, larger enterprises with their own network
      infrastructure, and government organizations, such as the
      military.

   Internet Service Provider (ISP):  An organization that provides IP
      network-layer services to its customers or users.  This entity may
      or may not provide the physical-layer and data link (layer-2)
      connectivity, such as fiber or Ethernet, i.e., it may or may not
      play the role of an IAP.

   Application Service Provider (ASP):  The organization or entity that
      provides application-layer services, which may include voice (see
      "Voice Service Provider").  This entity can be a private
      individual, an enterprise, a government, or a service provider.
      An ASP is more general than a Voice Service Provider, since
      emergency calls may use other media beyond voice, including text
      and video.  For a particular user, the ASP may or may not be the
      same organization as his IAP or ISP.

   Voice Service Provider (VSP):  A specific type of Application Service
      Provider that provides voice related services based on IP, such as
      call routing, a SIP URI, or PSTN termination.  In this document,
      unless noted otherwise, any reference to "Voice Service Provider"
      or "VSP" may be used interchangeably with "Application/Voice
      Service Provider" or "ASP/VSP".

3.3.  Actors

   (Emergency) caller:  The term "caller" or "emergency caller" refers
      to the person placing an emergency call or sending an emergency
      instant message (IM).

   User Equipment (UE):  User equipment is the device or software
      operated by the caller to place an emergency call.  A SIP user
      agent (UA) is an example of user equipment.

   Call taker:  A call taker is an agent at the PSAP that accepts calls
      and may dispatch emergency help.  Sometimes the functions of call
      taking and dispatching are handled by different groups of people,
      but these divisions of labor are not generally visible to the
      caller and thus do not concern us here.










Schulzrinne & Marshall       Informational                      [Page 4]
^L
RFC 5012                   ECRIT Requirements               January 2008


3.4.  Call Routing Entities

   Emergency Service Routing Proxy (ESRP):  An ESRP is an emergency call
      routing support entity that invokes the location-to-PSAP URI
      mapping function, to return an appropriate PSAP URI, or the URI
      for another ESRP.  Client mapping requests could also be performed
      by a number of entities, including entities that instantiate the
      SIP proxy role and the SIP user agent client role.

   Public Safety Answering Point (PSAP):  A PSAP is a facility where
      emergency calls are received under the responsibility of a public
      authority.  (This terminology is used by both the European
      Telecommunications Standards Institute (ETSI), in ETSI SR 002 180,
      and the National Emergency Number Association (NENA).)  In the
      United Kingdom, PSAPs are called Operator Assistance Centres; in
      New Zealand, Communications Centres.  Within this document, it is
      assumed, unless stated otherwise, that PSAPs support the receipt
      of emergency calls over IP, using appropriate application layer
      protocols, such as SIP for call signaling and RTP for media.

3.5.  Location

   Location:  A geographic identification assigned to a region or
      feature based on a specific coordinate system, or by other precise
      information such as a street number and name.  It can be either a
      civic or geographic location.

   Civic location:  A described location based on some reference system,
      such as jurisdictional region or postal delivery grid.  A street
      address is a common example of a civic location.

   Geographic location:  A reference to a point that is able to be
      located, as described by a set of defined coordinates within a
      geographic coordinate system, such as latitude and longitude
      within the WGS-84 datum.  For example, a 2-D geographic location
      is defined as an (x,y) coordinate value pair according to the
      distance north or south of the equator and east or west of the
      prime meridian.

   Location validation:  A caller location is considered valid if the
      civic or geographic location is recognizable within an acceptable
      location reference system (e.g., United States Postal Address or
      the WGS-84 datum) and can be mapped to one or more PSAPs.  While
      it is desirable to determine that a location exists, validation
      may not ensure that such a location exists, but rather may only






Schulzrinne & Marshall       Informational                      [Page 5]
^L
RFC 5012                   ECRIT Requirements               January 2008


      ensure that the location falls within some range of known values.
      Location validation ensures that a location is able to be
      referenced for mapping, but makes no assumption about the
      association between the caller and the caller's location.

3.6.  Identifiers, Numbers, and Dial Strings

   (Emergency) service number:  The (emergency) service number is a
      string of digits used to reach the (emergency) service.  The
      emergency service number is often just called the emergency
      number.  It is the number typically dialed on devices directly
      connected to the PSTN and the number reserved for emergency calls
      by national or regional numbering authorities.  It only contains
      the digits 0 through 9, #, and *.  The service number may depend
      on the location of the caller.  For example, the general emergency
      service number in the United States is 911 and the poison control
      service number is 18002221222.  In most cases, the service number
      and dial string are the same; they may differ in some private
      phone networks.  A service number may be carried in tel URLs
      [RFC3966], along with a context identifier.  In the North American
      numbering plan, some service numbers are three-digit N11 or
      service codes, but not all emergency numbers have three digits.  A
      caller may have to dial a service dial string (below) that differs
      from the service number when using a PBX.

   (Emergency) service dial string:  The service dial string identifies
      the string of digits that a caller must dial to reach a particular
      (emergency) service.  In devices directly connected to the PSTN,
      the service dial string is the same as the service number and may
      thus depend on the location of the caller.  However, in private
      phone networks, such as in PBXs, the service dial string consists
      of a dialing prefix to reach an outside line, followed by the
      emergency number.  For example, in a hotel, the dial string for
      emergency services in the United States might be 9911.  Dial
      strings may contain indications of pauses or wait-for-secondary-
      dial-tone indications.  Service dial strings are outside the scope
      of this document.

   (Emergency) service identifier:  The (emergency) service identifier
      describes the emergency service, independent of the user interface
      mechanism, the signaling protocol that is used to reach the
      service, or the caller's geographic location.  It is a protocol
      constant and used within the mapping and signaling protocols.  An
      example is the service URN [RFC5031].







Schulzrinne & Marshall       Informational                      [Page 6]
^L
RFC 5012                   ECRIT Requirements               January 2008


   (Emergency) service URL:  The service URL is a protocol-specific
      (e.g., SIP) or protocol-agnostic (e.g., im: [RFC3860]) identifier
      that contains the address of the PSAP or other emergency service.
      It depends on the specific signaling or data transport protocol
      used to reach the emergency service.

   Service URN:  A service URN is an implementation of a service
      identifier, which can be applied to both emergency and non-
      emergency contexts, e.g., urn:service:sos or
      urn:service:counseling.  Within this document, service URNs are
      referred to as 'emergency service URNs' [RFC5031].

   Home emergency number:  A home emergency number is the emergency
      number valid at the caller's customary home location, e.g., his
      permanent residence.  The home location may or may not coincide
      with the service area of the caller's VSP.

   Home emergency dial string:  A home dial string is the dial string
      valid at the caller's customary home location, e.g., his permanent
      residence.

   Visited emergency number:  A visited emergency number is the
      emergency number valid at the caller's current physical location.
      We distinguish the visited emergency number if the caller is
      traveling outside his home region.

   Visited emergency dial string:  A visited emergency dial string is
      the dial string number valid at the caller's current physical
      location.

3.7.  Mapping

   Mapping:  Mapping is the process of resolving a location to one or
      more PSAP URIs that directly identify a PSAP, or point to an
      intermediary that knows about a PSAP and that is designated as
      responsible for serving that location.

   Mapping client:  A mapping client interacts with the mapping server
      to learn one or more PSAP URIs for a given location.

   Mapping protocol:  A protocol used to convey the mapping request and
      response.

   Mapping server:  The mapping server holds information about the
      location-to-PSAP URI mapping.






Schulzrinne & Marshall       Informational                      [Page 7]
^L
RFC 5012                   ECRIT Requirements               January 2008


   Mapping service:  A network service that uses a distributed mapping
      protocol to perform a mapping between a location and a PSAP, or
      intermediary that knows about the PSAP, and is used to assist in
      routing an emergency call.

4.  Basic Actors

   In order to support emergency services covering a large physical
   area, various infrastructure elements are necessary, including
   Internet Access Providers (IAPs), Application/Voice Service Providers
   (ASP/VSPs), Emergency Service Routing Proxy (ESRP) providers, mapping
   service providers, and PSAPs.

   This section outlines which entities will be considered in the
   routing scenarios discussed.

      Location
      Information     +-----------------+
          |(1)        |Internet         |   +-----------+
          v           |Access           |   |           |
     +-----------+    |Provider         |   | Mapping   |
     |           |    | (3)             |   | Service   |
     | Emergency |<---+-----------------+-->|           |
     | Caller    |    | (2)             |   +-----------+
     |           |<---+-------+         |          ^
     +-----------+    |  +----|---------+------+   |
          ^           |  |   Location   |      |   |
          |           |  |   Information<-+    |   |
          |           +--+--------------+ |(5) |   | (6)
          |              |                |    |   |
          |              |    +-----------v+   |   |
          |   (4)        |    |            |   |   |
          +--------------+--->|    ESRP    |<--+---+
          |              |    |            |   |
          |              |    +------------+   |
          |              |          ^          |
          |              |      (7) |          |  +----+--+
          |    (8)       |          +------------>|       |
          +--------------+----------------------->| PSAP  |
                         |                     |  |       |
                         |Application/         |  +----+--+
                         |Voice                |
                         |Service              |
                         |Provider             |
                         +---------------------+

              Figure 1: Framework for Emergency Call Routing




Schulzrinne & Marshall       Informational                      [Page 8]
^L
RFC 5012                   ECRIT Requirements               January 2008


   Figure 1 shows the interaction between the entities involved in the
   call.  There are a number of different deployment choices, as can be
   easily seen from the figure.

   Is the Internet Access Provider also the Application/Voice Service
   Provider?  In the Internet today, the roles of Internet access
   provider and application/voice service provider are typically
   provided by different entities.  As a consequence, the Application/
   Voice Service Provider is typically not able to directly determine
   the physical location of the emergency caller.

   The overlapping squares in the figure indicate that some functions
   can be collapsed into a single entity.  As an example, the
   Application/Voice Service Provider might be the same entity as the
   Internet Access Provider.  There is, however, no requirement that
   this must be the case.  Additionally, we consider that end systems
   might act as their own ASP/VSP, e.g., either for enterprises or for
   residential users.

   Various potential interactions between the entities depicted in
   Figure 1 are described below:

   1.  Location information might be available to the end host itself.

   2.  Location information might, however, also be obtained from the
       Internet Access Provider.

   3.  The emergency caller might need to consult a mapping service to
       determine the PSAP (or other relevant information) that is
       appropriate for the physical location of the emergency caller,
       possibly considering other attributes, such as appropriate
       language support by the emergency call taker.

   4.  The emergency caller might get assistance for emergency call
       routing by infrastructure elements that are emergency call
       routing support entities, such as an Emergency Service Routing
       Proxy (ESRP) in SIP.

   5.  Location information is used by emergency call routing support
       entities for subsequent mapping requests.

   6.  Emergency call routing support entities might need to consult a
       mapping service to determine where to route the emergency call.

   7.  For infrastructure-based emergency call routing (in contrast to
       UE-based emergency call routing), the emergency call routing
       support entity needs to forward the call to the PSAP.




Schulzrinne & Marshall       Informational                      [Page 9]
^L
RFC 5012                   ECRIT Requirements               January 2008


   8.  The emergency caller may interact directly with the PSAP, where
       the UE invokes mapping, and initiates a connection, without
       relying on any intermediary emergency call routing support
       entities.

5.  High-Level Requirements

   Below, we summarize high-level architectural requirements that guide
   some of the component requirements detailed later in the document.

   Re1.  Application/Voice service provider existence:  The initiation
      of an IP-based emergency call SHOULD NOT assume the existence of
      an Application/Voice Service Provider (ASP/VSP).

      Motivation: The caller may not have an application/voice service
      provider.  For example, a residence may have its own DNS domain
      and run its own SIP proxy server for that domain.  On a larger
      scale, a university might provide voice services to its students
      and staff, but might not be a telecommunication provider.

   Re2.  International applicability:  Regional, political, and
      organizational aspects MUST be considered during the design of
      protocols and protocol extensions that support IP-based emergency
      calls.

      Motivation: It must be possible for a device or software developed
      or purchased in one country to place emergency calls in another
      country.  System components should not be biased towards a
      particular set of emergency numbers or languages.  Also, different
      countries have evolved different ways of organizing emergency
      services, e.g., either centralizing them or having smaller
      regional subdivisions, such as the United States or
      municipalities, handle emergency calls within their jurisdiction.

   Re3.  Distributed administration:  Deployment of IP-based emergency
      services MUST NOT depend on a single central administrative
      authority.

      Motivation: The design of the mapping protocol must make it
      possible to deploy and administer emergency calling features on a
      regional or national basis without requiring coordination with
      other regions or nations.  The system cannot assume, for example,
      that there is a single global entity issuing certificates for
      PSAPs, ASP/VSPs, IAPs, or other participants.







Schulzrinne & Marshall       Informational                     [Page 10]
^L
RFC 5012                   ECRIT Requirements               January 2008


   Re4.  Multi-mode communication:  IP-based emergency calls MUST
      support multiple communication modes, including, for example,
      audio, video, and text.

      Motivation: Within the PSTN, voice and text telephony (often
      called TTY or text-phone in North America) are the only commonly
      supported media.  Emergency calling must support a variety of
      media.  Such media should include voice, conversational text (RFC
      4103 [RFC4103]), instant messaging, and video.

   Re5.  Mapping result usability:  The mapping protocol MUST return one
      or more URIs that are usable within a standard signaling protocol
      (i.e., without special emergency extensions).

      Motivation: For example, a SIP URI that is returned by the mapping
      protocol needs to be usable by any SIP-capable phone within a SIP-
      initiated emergency call.  This is in contrast to a "special
      purpose" URI, which may not be recognizable by a legacy SIP
      device.

   Re6.  PSAP URI accessibility:  The mapping protocol MUST support
      interaction between the client and server where no enrollment to a
      mapping service exists or is required.

      Motivation: The mapping server may well be operated by a service
      provider, but access to the server offering the mapping must not
      require use of a specific ISP or ASP/VSP.

   Re7.  Common data structures and formats:  The mapping protocol
      SHOULD support common formats (e.g., PIDF-LO) for location data.

      Motivation: Location databases should not need to be transformed
      or modified in any unusual or unreasonable way in order for the
      mapping protocol to use the data.  For example, a database that
      contains civic addresses used by location servers may be used for
      multiple purposes and applications beyond emergency service
      location-to-PSAP URI mapping.

   Re8.  Anonymous mapping:  The mapping protocol MUST NOT require the
      true identity of the target for which the location information is
      attributed.

      Motivation: Ideally, no identity information is provided via the
      mapping protocol.  Where identity information is provided, it may
      be in the form of an unlinked pseudonym (RFC 3693 [RFC3693]).






Schulzrinne & Marshall       Informational                     [Page 11]
^L
RFC 5012                   ECRIT Requirements               January 2008


6.  Identifying the Caller's Location

   Location can either be provided directly (by value), or via a pointer
   (by reference), and represents either a civic location, or a
   geographic location.  An important question is how and when to attach
   location information to the VoIP emergency signaling messages.  In
   general, we can distinguish three modes of operation of how a
   location is associated with an emergency call:

   UA-inserted:  The caller's user agent inserts the location
      information into the call-signaling message.

   UA-referenced:  The caller's user agent provides a pointer (i.e., a
      location reference), via a permanent or temporary identifier, to
      the location information, which is stored by a location server
      somewhere else and then retrieved by the PSAP, ESRP, or other
      authorized entity.

   Proxy-inserted:  A proxy along the call path inserts the location or
      location reference.

   The following requirements apply:

   Lo1.  Reference datum:  The mapping protocol MUST support the WGS-84
      coordinate reference system and MAY support other coordinate
      reference systems.

      Motivation: Though many different datums exist around the world,
      this document recommends the WGS-84 datum since it is designed to
      describe the whole earth, rather than a single continent or other
      region, and is commonly used to represent Global Positioning
      System coordinates.

   Lo2.  Location delivery by-value:  The mapping protocol MUST support
      the delivery of location information using a by-value method,
      though it MAY also support de-referencing a URL that references a
      location object.

      Motivation: The mapping protocol is not required to support the
      ability to de-reference specific location references.

   Lo3.  Alternate community names:  The mapping protocol MUST support
      both the jurisdictional community name and the postal community
      name fields within the PIDF-LO [RFC4119] data.







Schulzrinne & Marshall       Informational                     [Page 12]
^L
RFC 5012                   ECRIT Requirements               January 2008


      Motivation: The mapping protocol must accept queries with either a
      postal or jurisdictional community name field, or both, and
      provide appropriate responses.  If a mapping query contains only
      one community name and the database contains both jurisdictional
      and postal community names, the mapping protocol response SHOULD
      return both community names.

   Lo4.  Validation of civic location:  The mapping protocol MUST be
      able to report the results of validating civic locations (street
      addresses).

      Motivation: Location validation provides an opportunity to help
      ascertain ahead of time whether or not a successful mapping to the
      appropriate PSAP will likely occur when it is required.
      Validation may also help to avoid delays during emergency call
      setup due to invalid location data.

   Lo5.  Information about location data used for mapping:  The mapping
      protocol MUST support the ability to provide ancillary information
      about the resolution of location data used to retrieve a PSAP URI.

      Motivation: The mapping server may not use all the data elements
      in the provided location information to determine a match, or may
      be able to find a match based on all of the information except for
      some specific data elements.  The uniqueness of this information
      set may be used to differentiate among emergency jurisdictions.
      Precision or resolution in the context of this requirement might
      mean, for example, explicit identification of the data elements
      that were used successfully in the mapping.

   Lo6.  Contact for location problems:  The mapping protocol MUST
      support a mechanism to contact an appropriate authority to resolve
      mapping-related issues for the queried location.  For example, the
      querier may want to report problems with the response values or
      indicate that the mapping database is mistaken on declaring a
      civic location as non-existent.

      Motivation: Initially, authorities may provide URLs where a human
      user can report problems with an address or location.  In
      addition, web services may be defined to automate such reporting.
      For example, the querier may wish to report that the mapping
      database may be missing a newly built or renamed street or house
      number.

   Lo7.  Limits to validation:  Successful validation of a civic
      location MUST NOT be required to place an emergency call.





Schulzrinne & Marshall       Informational                     [Page 13]
^L
RFC 5012                   ECRIT Requirements               January 2008


      Motivation: In some cases, a civic location may not be considered
      valid.  This fact should not result in the call being dropped or
      rejected by any entity along the call setup signaling path to the
      PSAP.

   Lo8. 3D sensitive mapping:  The mapping protocol MUST implement
      support for both 2D and 3D location information, and MAY accept
      either a 2D or 3D mapping request as input.

      Motivation: It is expected that queriers may provide either 2D or
      3D data.  When a 3D request is presented within an area only
      defined by 2D data within the mapping server, the mapping result
      would be the same as if the height or altitude coordinate had been
      omitted from the mapping request.

   Lo9.  Database type indicator:  The mapping protocol MAY support a
      mechanism that provides an indication describing a specific type
      of location database used.

      Motivation: It is useful to know the source of the data stored in
      the database used for location validation, either for civic or
      geographic location matching.  In the United States, sources of
      data could include the United States Postal Service, the Master
      Street Address Guide (MSAG), or commercial map data providers.

7.  Emergency Service Identifier

   Emergency service identifiers are protocol constants that allow
   protocol entities, such as SIP proxy servers, to distinguish
   emergency calls from non-emergency calls and to identify the specific
   emergency service desired.  Emergency service identifiers are a
   subclass of service identifiers that more generally identify services
   reachable by callers.  An example of a service identifier is the
   service URN [RFC5031], but other identifiers, such as tel URIs
   [RFC3966], may also serve this role during a transition period.

   Since this document only addresses emergency services, we use the
   terms "emergency service identifier" and "service identifier"
   interchangeably.  Requirements for these identifiers include:

   Id1.  Multiple emergency services:  The mapping protocol MUST be able
      to support different emergency services distinguished by different
      service identifiers.

      Motivation: Some jurisdictions may offer multiple types of
      emergency services that operate independently and can be contacted
      directly; for example, fire, police, and ambulance services.




Schulzrinne & Marshall       Informational                     [Page 14]
^L
RFC 5012                   ECRIT Requirements               January 2008


   Id2.  Extensible emergency service identifiers:  The mapping protocol
      MUST support an extensible list of emergency identifiers, though
      it is not required to provide mappings for every possible service.

      Motivation: Extensibility is required since new emergency services
      may be introduced over time, either globally or in some
      jurisdictions.  The availability of emergency services depends on
      the locations.  For example, the Netherlands are unlikely to offer
      a mountain rescue service.

   Id3.  Discovery of emergency number:  The mapping protocol MUST be
      able to return the location-dependent emergency number for the
      location indicated in the query.

      Motivation: Users are trained to dial the appropriate emergency
      number to reach emergency services.  There needs to be a way to
      figure out the emergency number at the current location of the
      caller.

   Id4.  Home emergency number recognition:  User equipment MUST be able
      to translate a home emergency number into an emergency service
      identifier.

      Motivation: The UE could be pre-provisioned with the appropriate
      information in order to perform such a translation or could
      discover the emergency number by querying the mapping protocol
      with its home location.

   Id5.  Emergency number replacement:  There SHOULD be support for
      replacement of the emergency number with the appropriate emergency
      service identifier for each signaling protocol used for an
      emergency call, based on local conventions, regulations, or
      preference (e.g., as in the case of an enterprise).

      Motivation: Any signaling protocol requires the use of some
      identifier to indicate the called party, and the user equipment
      may lack the capability to determine the actual service URL (PSAP
      URI).  The use of local conventions may be required as a
      transition mechanism.  Since relying on recognizing local
      numbering conventions makes it difficult for devices to be used
      outside their home context and for external devices to be
      introduced into a network, protocols should use standardized
      emergency service identifiers.

   Id6.  Emergency service identifier marking:  Signaling protocols MUST
      support emergency service identifiers to mark a call as an
      emergency call.




Schulzrinne & Marshall       Informational                     [Page 15]
^L
RFC 5012                   ECRIT Requirements               January 2008


      Motivation: Marking ensures proper handling as an emergency call
      by downstream elements that may not recognize, for example, a
      local variant of a logical emergency address.  This marking
      mechanism is related to, but independent of, marking calls for
      prioritized call handling [RFC4412].

   Id7.  Handling unrecognized emergency service identifiers:  There
      MUST be support for calls that are initiated as emergency calls
      even if the specific emergency service requested is not recognized
      by the ESRP.  Such calls will then be routed to a generic
      emergency service.

      Motivation: Fallback routing allows new emergency services to be
      introduced incrementally, while avoiding non-routable emergency
      calls.  For example, a call for marine rescue services would be
      routed to a general PSAP if the caller's location does not offer
      marine rescue services yet.

   Id8.  Return fallback service identifier:  The mapping protocol MUST
      be able to report back the actual service mapped if the mapping
      protocol substitutes another service for the one requested.

      Motivation: A mapping server may be configured to automatically
      look up the PSAP for another service if the user-requested service
      is not available for that location.  For example, if there is no
      marine rescue service, the mapping protocol might return the PSAP
      URL for general emergencies and include the "urn:service.sos"
      identifier in the response to alert the querier to that fact.

   Id9.  Discovery of visited emergency numbers:  The mapping protocol
      MUST support a mechanism to allow the end device to learn visited
      emergency numbers.

      Motivation: Travelers visiting a foreign country may observe the
      local emergency number, e.g., seeing it painted on the side of a
      fire truck, and then rightfully expect to be able to dial that
      emergency number.  Similarly, a local "good Samaritan" may use a
      tourist's cell phone to summon help.

8.  Mapping Protocol

   There are two basic approaches to invoke the mapping protocol.  We
   refer to these as caller-based and mediated.  In each case, the
   mapping client initiates a request to a mapping server via a mapping
   protocol.  A proposed mapping protocol, LoST, is outlined in [lost].

   For caller-based resolution, the caller's user agent invokes the
   mapping protocol to determine the appropriate PSAP based on the



Schulzrinne & Marshall       Informational                     [Page 16]
^L
RFC 5012                   ECRIT Requirements               January 2008


   location provided.  The resolution may take place well before the
   actual emergency call is placed, or at the time of the call.

   For mediated resolution, an emergency call routing support entity,
   such as a SIP (outbound) proxy or redirect server, invokes the
   mapping service.

   Since servers may be used as outbound proxy servers by clients that
   are not in the same geographic area as the proxy server, any proxy
   server has to be able to translate any caller location to the
   appropriate PSAP.  (A traveler may, for example, accidentally or
   intentionally configure its home proxy server as its outbound proxy
   server, even while far away from home.)

   Ma1.  Baseline query protocol:  A mandatory-to-implement protocol
      MUST be specified.

      Motivation: An over-abundance of similarly capable choices appears
      undesirable for interoperability.

   Ma2.  Extensible protocol:  The mapping protocol MUST be designed to
      support the extensibility of location data elements, both for new
      and existing fields.

      Motivation: This is needed, for example, to accommodate future
      extensions-to-location information that might be included in the
      PIDF-LO ([RFC4119]).

   Ma3.  Incrementally deployable:  The mapping protocol MUST be
      designed to support its incremental deployment.

      Motivation: It must not be necessary, for example, to have a
      global street level database before deploying the system.  It is
      acceptable to have some misrouting of calls when the database does
      not (yet) contain accurate PSAP service area information.

   Ma4.  Any time mapping:  The mapping protocol MUST support the
      ability of the mapping function to be invoked at any time,
      including while an emergency call is in process and before an
      emergency call is initiated.

      Motivation: If the mapping query fails at call time, it may be
      advantageous to be able to fall back to the result of an earlier
      mapping query.  This prior knowledge would be obtained by
      performing a mapping query at any time prior to an emergency call.






Schulzrinne & Marshall       Informational                     [Page 17]
^L
RFC 5012                   ECRIT Requirements               January 2008


   Ma5.  Anywhere mapping:  The mapping protocol MUST support the
      ability to provide mapping information in response to an
      individual query from any (earthly) location, regardless of where
      the mapping client is located, either geographically or by network
      location.

      Motivation: The mapping client, such as an ESRP, may not
      necessarily be anywhere close to the caller or the appropriate
      PSAP, but must still be able to obtain mapping information.

   Ma6.  Appropriate PSAP:  The mapping protocol MUST support the
      routing of an emergency call to the PSAP responsible for a
      particular geographic area.

      Motivation: Routing to the wrong PSAP will result in delays in
      handling emergencies as calls are redirected, and therefore will
      also result in inefficient use of PSAP resources at the initial
      point of contact.  It is important that the location determination
      mechanism not be fooled by the location of IP telephony gateways
      or dial-in lines into a corporate LAN (and dispatch emergency help
      to the gateway or campus, rather than the caller), multi-site LANs
      and similar arrangements.

   Ma7.  Multiple PSAP URIs:  The mapping protocol MUST support a method
      to return multiple PSAP URIs, which cover the same geographic
      area.

      Motivation: Different contact protocols (e.g., PSTN via tel URIs
      and IP via SIP URIs) may be routed to different PSAPs.  Less
      likely, two PSAPs may overlap in their coverage region.

   Ma8.  Single primary URI per contact protocol:  Though the mapping
      protocol may be able to include multiple URIs in the response, it
      SHOULD return only one primary URI per contact protocol used, so
      that clients are not required to select among different targets
      for the same contact protocol.

      Motivation: There may be two or more URIs returned when multiple
      contact protocols are available (e.g., SIP and SMS).  The client
      may select among multiple contact protocols based on its
      capabilities, preference settings, or availability.

   Ma9.  Non-preferred URI schemes:  The mapping protocol MAY support
      the return of a less-preferred URI scheme, such as a tel URI.

      Motivation: In order to provide incremental support to non-IP
      PSAPs, it may be necessary to be able to complete an emergency
      call via the PSTN.



Schulzrinne & Marshall       Informational                     [Page 18]
^L
RFC 5012                   ECRIT Requirements               January 2008


   Ma10.  URI properties:  The mapping protocol MUST support the ability
      to provide ancillary information about a contact that allows the
      mapping client to determine relevant properties of the PSAP URI.

      Motivation: In some cases, the same geographic area is served by
      several PSAPs; for example, a corporate campus might be served by
      both a corporate security department and the municipal PSAP.  The
      mapping protocol should then return URIs for both, with
      information allowing the querying entity to choose one or the
      other.  This determination could be made by either an ESRP, based
      on local policy, or by direct user choice, in the case of caller-
      based methods.

   Ma11.  Mapping referral:  The mapping protocol MUST support a
      mechanism for the mapping client to contact any mapping server and
      be referred to another mapping server that is more qualified to
      answer the query.

      Motivation: Referrals help mitigate the impact of incorrect
      configuration that directs a client to the wrong initial mapping
      server.

   Ma12.  Split responsibility:  The mapping protocol MUST support the
      division of data subset handling between multiple mapping servers
      within a single level of a civic location hierarchy.

      Motivation: For example, two mapping servers for the same city or
      county may handle different streets within that city or county.

   Ma13.  URL for error reporting:  The mapping protocol MUST support
      the ability to return a URL that can be used to report a suspected
      or known error within the mapping database.

      Motivation: If an error is returned, for example, there needs to
      be a URL that points to a resource that can explain or potentially
      help resolve the error.

   Ma14.  Resilience to mapping server failure:  The mapping protocol
      MUST support a mechanism that enables the client to fail over to
      different (replica) mapping server.

      Motivation: The failure of a mapping server should not preclude
      the mapping client from receiving an answer to its query.

   Ma15.  Traceable resolution:  The mapping protocol SHOULD support the
      ability of the mapping client to be able to determine the entity
      or entities that provided the emergency address resolution
      information.



Schulzrinne & Marshall       Informational                     [Page 19]
^L
RFC 5012                   ECRIT Requirements               January 2008


      Motivation: To improve reliability and performance, it is
      important to be able to trace which servers contributed to the
      resolution of a query.

   Ma16.  Minimal additional delay:  Mapping protocol execution SHOULD
      minimize the amount of delay within the overall call-setup time.

      Motivation: Since outbound proxies will likely be asked to resolve
      the same geographic coordinates repeatedly, a suitable time-
      limited caching mechanism should be supported.

   Ma17.  Freshness indication:  The mapping protocol SHOULD support an
      indicator describing how current the information provided by the
      mapping source is.

      Motivation: This is especially useful when an alternate mapping is
      requested, and alternative sources of mapping data may not have
      been created or updated with the same set of information or within
      the same time frame.  Differences in currency between mapping data
      contained within mapping sources should be minimized.

9.  Security Considerations

   Threats and security requirements are discussed in a separate
   document [RFC5069].

10.  Contributors

   The information in this document is partially derived from text
   written by the following contributors:

   Nadine Abbott          nabbott@telcordia.com

   Hideki Arai            arai859@oki.com

   Martin Dawson          Martin.Dawson@andrew.com

   Motoharu Kawanishi     kawanishi381@oki.com

   Brian Rosen            br@brianrosen.net

   Richard Stastny        Richard.Stastny@oefeg.at

   Martin Thomson         Martin.Thomson@andrew.com

   James Winterbottom     James.Winterbottom@andrew.com





Schulzrinne & Marshall       Informational                     [Page 20]
^L
RFC 5012                   ECRIT Requirements               January 2008


11.  Acknowledgments

   In addition to thanking those listed above, we would like to also
   thank Guy Caron, Barry Dingle, Keith Drage, Tim Dunn, Patrik
   Faltstrom, Clive D.W. Feather, Raymond Forbes, Randall Gellens,
   Michael Haberler, Michael Hammer, Ted Hardie, Gunnar Hellstrom,
   Cullen Jennings, Marc Linsner, Rohan Mahy, Patti McCalmont, Don
   Mitchell, John Morris, Andrew Newton, Steve Norreys, Jon Peterson,
   James Polk, Benny Rodrig, John Rosenberg, Jonathan Rosenberg, John
   Schnizlein, Shida Schubert, James Seng, Byron Smith, Barbara Stark,
   Richard Stastny, Tom Taylor, Hannes Tschofenig, and Nate Wilcox for
   their helpful input.

12.  References

12.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

12.2.  Informative References

   [RFC3261]  Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
              A., Peterson, J., Sparks, R., Handley, M., and E.
              Schooler, "SIP: Session Initiation Protocol", RFC 3261,
              June 2002.

   [RFC3351]  Charlton, N., Gasson, M., Gybels, G., Spanner, M., and A.
              van Wijk, "User Requirements for the Session Initiation
              Protocol (SIP) in Support of Deaf, Hard of Hearing and
              Speech-impaired Individuals", RFC 3351, August 2002.

   [RFC3693]  Cuellar, J., Morris, J., Mulligan, D., Peterson, J., and
              J. Polk, "Geopriv Requirements", RFC 3693, February 2004.

   [RFC3860]  Peterson, J., "Common Profile for Instant Messaging
              (CPIM)", RFC 3860, August 2004.

   [RFC3966]  Schulzrinne, H., "The tel URI for Telephone Numbers",
              RFC 3966, December 2004.

   [RFC4103]  Hellstrom, G. and P. Jones, "RTP Payload for Text
              Conversation", RFC 4103, June 2005.

   [RFC4119]  Peterson, J., "A Presence-based GEOPRIV Location Object
              Format", RFC 4119, December 2005.





Schulzrinne & Marshall       Informational                     [Page 21]
^L
RFC 5012                   ECRIT Requirements               January 2008


   [RFC4412]  Schulzrinne, H. and J. Polk, "Communications Resource
              Priority for the Session Initiation Protocol (SIP)",
              RFC 4412, February 2006.

   [RFC5031]  Schulzrinne, H., "A Uniform Resource Name (URN) for
              Emergency and Other Well-Known Services", RFC 5031,
              January 2008.

   [RFC5069]  Taylor, T., Ed., Tschofenig, H., Schulzrinne, H., and M.
              Shanmugam, "Security Threats and Requirements for
              Emergency Call Marking and Mapping", RFC 5069,
              January 2008.

   [lost]     Hardie, T., "LoST: A Location-to-Service Translation
              Protocol", Work in Progress, August 2007.

   [toip]     Wijk, A. and G. Gybels, "Framework for real-time text over
              IP using the Session Initiation Protocol  (SIP)", Work
              in Progress, August 2006.

Authors' Addresses

   Henning Schulzrinne
   Columbia University
   Department of Computer Science
   450 Computer Science Building
   New York, NY  10027
   US

   Phone: +1 212 939 7004
   EMail: hgs+ecrit@cs.columbia.edu
   URI:   http://www.cs.columbia.edu


   Roger Marshall (editor)
   TeleCommunication Systems, Inc.
   2401 Elliott Avenue
   2nd Floor
   Seattle, WA  98121
   US

   Phone: +1 206 792 2424
   EMail: rmarshall@telecomsys.com
   URI:   http://www.telecomsys.com







Schulzrinne & Marshall       Informational                     [Page 22]
^L
RFC 5012                   ECRIT Requirements               January 2008


Full Copyright Statement

   Copyright (C) The IETF Trust (2008).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.












Schulzrinne & Marshall       Informational                     [Page 23]
^L