path: root/doc/rfc/rfc7412.txt

Internet Engineering Task Force (IETF)                     Y. Weingarten
Request for Comments: 7412
Category: Informational                                        S. Aldrin
ISSN: 2070-1721                                      Huawei Technologies
                                                                  P. Pan
                                                                Infinera
                                                                 J. Ryoo
                                                                    ETRI
                                                               G. Mirsky
                                                                Ericsson
                                                           December 2014


           Requirements for MPLS Transport Profile (MPLS-TP)
                         Shared Mesh Protection

Abstract

   This document presents the basic network objectives for the behavior
   of Shared Mesh Protection (SMP) that are not based on control-plane
   support.  This document provides an expansion of the basic
   requirements presented in RFC 5654 ("Requirements of an MPLS
   Transport Profile") and RFC 6372 ("MPLS Transport Profile (MPLS-TP)
   Survivability Framework").  This document provides requirements for
   any mechanism that would be used to implement SMP for MPLS-TP data
   paths, in networks that delegate protection switch coordination to
   the data plane.

Status of This Memo

   This document is not an Internet Standards Track specification; it is
   published for informational purposes.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Not all documents
   approved by the IESG are a candidate for any level of Internet
   Standard; see Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc7412.








Weingarten, et al.            Informational                     [Page 1]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


Copyright Notice

   Copyright (c) 2014 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1. Introduction ....................................................3
   2. Terminology and Notation ........................................3
      2.1. Acronyms and Terminology ...................................4
   3. Shared Mesh Protection Reference Model ..........................4
      3.1. Protection or Restoration ..................................5
      3.2. Scope of Document ..........................................5
           3.2.1. Relationship to MPLS ................................5
   4. SMP Architecture ................................................6
      4.1. Coordination of Resources ..................................8
      4.2. Control Plane or Data Plane ................................8
   5. SMP Network Objectives ..........................................9
      5.1. Resource Reservation and Coordination ......................9
           5.1.1. Checking Resource Availability for Multiple
                  Protection Paths ....................................9
      5.2. Multiple Triggers .........................................10
           5.2.1. Soft Preemption ....................................10
           5.2.2. Hard Preemption ....................................10
      5.3. Notification ..............................................11
      5.4. Reversion .................................................11
      5.5. Protection Switching Time .................................11
      5.6. Timers ....................................................12
      5.7. Communication Channel and Fate-Sharing ....................12
   6. Manageability Considerations ...................................13
   7. Security Considerations ........................................13
   8. Normative References ...........................................13
   Acknowledgements ..................................................15
   Contributors ......................................................15
   Authors' Addresses ................................................16






Weingarten, et al.            Informational                     [Page 2]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


1.  Introduction

   The MPLS Transport Profile (MPLS-TP) is described in [RFC5921].
   [RFC6372] provides a survivability framework for MPLS-TP and is the
   foundation for this document.

   Terminology for recovery of connectivity in networks is provided in
   [RFC4427] and includes the concept of surviving network faults
   (survivability) through the use of re-established connections
   (restoration) and switching of traffic to pre-established backup
   paths (protection).  MPLS provides control-plane tools to support
   various survivability schemes, some of which are identified in
   [RFC4426].  In addition, recent efforts in the IETF have started
   providing for data-plane tools to address aspects of data protection.
   In particular, [RFC6378] and [RFC7271] define a set of triggers and
   coordination protocols for 1:1 and 1+1 linear protection of point-to-
   point paths.

   When considering a full-mesh network and the protection of different
   paths that traverse the mesh, it is possible to provide an acceptable
   level of protection while conserving the amount of protection
   resources needed to protect the different data paths.  As pointed out
   in [RFC6372] and [RFC4427], applying 1+1 protection requires that
   resources are allocated for use by both the working and protection
   paths.  Applying 1:1 protection requires that the same resources are
   allocated but allows the resources of the protection path to be
   utilized for preemptible extra traffic.  Extending this to 1:n or m:n
   protection allows the resources of the protection path to be shared
   in the protection of several working paths.  However, 1:n or m:n
   protection architecture is limited by the restriction that all of the
   n+1 or m+n paths must have the same endpoints.  m:n protection
   architecture provides m protection paths to protect n working paths,
   where m or n can be 1.

   This document provides requirements for any mechanism that would be
   used to implement SMP for MPLS-TP data paths, in networks that
   delegate protection switch coordination to the data plane.

2.  Terminology and Notation

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

   Although this document is not a protocol specification, the use of
   this language clarifies the instructions to protocol designers
   producing solutions that satisfy the requirements set out in this
   document.



Weingarten, et al.            Informational                     [Page 3]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


   The terminology used in this document is based on the terminology
   defined in the MPLS-TP Survivability Framework document [RFC6372],
   which in turn is based on [RFC4427].

2.1.  Acronyms and Terminology

   This document uses the following acronyms:

      LSP  Label Switched Path
      SLA  Service Level Agreement
      SMP  Shared Mesh Protection
      SRLG Shared Risk Link Group

   This document defines the following term:

   SMP Protection Group: the set of different protection paths that
      share a common segment.

3.  Shared Mesh Protection Reference Model

   As described in [RFC6372], SMP supports the sharing of protection
   resources, while providing protection for multiple working paths that
   need not have common endpoints and do not share common points of
   failure.  Note that some protection resources may be shared, while
   some others may not be.  An example of data paths that employ SMP is
   shown in Figure 1.  It shows two working paths -- <ABCDE> and <VWXYZ>
   -- that are protected employing 1:1 linear protection by protection
   paths <APQRE> and <VPQRZ>, respectively.  The two protection paths
   that traverse segment <PQR> share the protection resources on this
   segment.

                           A----B----C----D----E
                            \                 /
                             \               /
                              \             /
                               P-----Q-----R
                              /             \
                             /               \
                            /                 \
                           V----W----X----Y----Z

                     Figure 1: Basic SMP Architecture









Weingarten, et al.            Informational                     [Page 4]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


3.1.  Protection or Restoration

   [RFC6372], based upon the definitions in [RFC4427], differentiates
   between "protection" and "restoration", depending on the dynamism of
   the resource allocation.  The same distinction is used in [RFC3945],
   [RFC4426], and [RFC4428].

   This document also uses the same distinction between protection and
   restoration as the distinction stated in [RFC6372].

3.2.  Scope of Document

   [RFC5654] establishes that MPLS-TP SHOULD support shared protection
   (Requirement 68) and that MPLS-TP MUST support sharing of protection
   resources (Requirement 69).  This document presents the network
   objectives and a framework for applying SMP within an MPLS network,
   without the use of control-plane protocols.  Although there are
   existing control-plane solutions for SMP within MPLS, a data-plane
   solution is required for networks that do not employ a full control-
   plane operation for some reason (e.g., service provider preferences
   or limitations) or require service restoration faster than is
   achievable with control-plane mechanisms.

   The network objectives will also address possible additional
   restrictions on the behavior of SMP in networks that delegate
   protection switching for resiliency to the data plane.  Definitions
   of logic and specific protocol messaging are out of scope for this
   document.

3.2.1.  Relationship to MPLS

   While some of the restrictions presented by this document originate
   from the properties of transport networks, nothing prevents the
   information presented here from being applied to MPLS networks
   outside the scope of the Transport Profile of MPLS.
















Weingarten, et al.            Informational                     [Page 5]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


4.  SMP Architecture

   Figure 1 shows a very basic configuration of working and protection
   paths that may employ SMP.  We may consider a slightly more complex
   configuration, such as the one in Figure 2 in order to illustrate
   characteristics of a mesh network that implements SMP.

                      A----B----C----D----E---N
                       \            /    /    \
                        \          M ---/--    \
                         \             /   \    \
                          P-----Q-----R-----S----T
                         /|      \     \     \    \
                        / F---G---H    J--K---L    \
                       /                            \
                      V------W-------X-------Y-------Z

              Figure 2: Example of a Larger SMP Architecture

   Consider the network presented in Figure 2.  There are five working
   paths:

      -  <ABCDE>

      -  <MDEN>

      -  <FGH>

      -  <JKL>

      -  <VWXYZ>

   Each of these has a corresponding protection path:

      -  <APQRE> (p1)

      -  <MSTN> (p2)

      -  <FPQH> (p3)

      -  <JRSL> (p4)

      -  <VPQRSTZ> (p5)








Weingarten, et al.            Informational                     [Page 6]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


   The following segments are shared by two or more of the protection
   paths -- <PQ> is shared by p1, p3, and p5; <QR> is shared by p1 and
   p5; <RS> is shared by p4 and p5; and <ST> is shared by p2 and p5.  In
   Figure 2, we have the following SMP Protection Groups -- {p1, p3, p5}
   for <PQ>, {p1, p5} for <QR>, {p4, p5} for <RS>, and {p2, p5}
   for <ST>.

   We assume that the available protection resources for these shared
   segments are not sufficient to support the complete traffic capacity
   of the respective working paths that may use the protection paths.
   We can further observe that with a method of coordinating sharing and
   preemption, there are no co-routing constraints on shared components
   at the segment level.

   The use of preemption in the network is typically a business or
   policy decision such that when protection resources are contested,
   priority can be applied to determine which parties utilize the
   protection resources.

   As opposed to the case of simple linear protection, where the
   relationship between the working and protection paths is defined and
   the resources for the protection path are fully dedicated, the
   protection path in the case of SMP consists of segments that are used
   for the protection of the related working path and also segments that
   are shared with other protection paths such that typically the
   protection resources are oversubscribed to support working paths that
   do not share common points of failure.  What is required is a
   preemption mechanism to implement business priority when multiple
   failure scenarios occur.  As such, the protection resources may be
   allocated but would not be utilized until requested and resolved in
   relation to other members of the SMP Protection Group as part of a
   protection switchover.

   [RFC6372] defines two types of preemption that can be considered for
   how the resources of SMP Protection Groups are shared: "soft
   preemption", where traffic of lower-priority paths is degraded; and
   "hard preemption", where traffic of lower-priority paths is
   completely blocked.  The traffic of lower-priority paths in this
   document can be viewed as the extra traffic being preempted, as
   described in [RFC6372].  "Hard preemption" requires the programming
   of selectors at the ingress of each shared segment to specify the
   priorities of backup paths, so that traffic of lower-priority paths
   can be preempted.  When any protection mechanism where the protection
   endpoint may have a choice of protection paths (e.g., m:n or m:1) is
   deployed, the shared segment selectors require coordination with the
   protection endpoints as well.





Weingarten, et al.            Informational                     [Page 7]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


   Typical deployment of services that use SMP requires various network
   planning activities.  These include the following:

   o  Determining the number of working and protection paths required to
      achieve resiliency targets for the service.

   o  Reviewing network topology to determine which working or
      protection paths are required to be disjoint from each other, and
      excluding specified resources such as links, nodes, or shared risk
      link groups (SRLGs).

   o  Determining the size (bandwidth) of the shared resource.

4.1.  Coordination of Resources

   When a protection switch is triggered, the SMP network performs two
   operations -- switching data traffic over to a protection path and
   coordinating the utilization of the associated shared resources.
   Both operations should occur at the same time, or as close together
   as possible, to provide fast protection.  The resource utilization
   coordination is dependent upon their availability at each of the
   shared segments.

   When the reserved resources of the shared segments are utilized by a
   particular protection path, there may not be sufficient resources
   available for an additional protection path.  This then implies that
   if another working path of the SMP domain triggers a protection
   switch, the resource utilization coordination may fail.  The
   different working paths in the SMP network are involved in the
   resource utilization coordination, which is a part of a whole SMP
   protection switching coordination.

4.2.  Control Plane or Data Plane

   As stated in both [RFC6372] and [RFC4428], full control of SMP,
   including both configuration and the coordination of the protection
   switching, is potentially very complex.  Therefore, it is suggested
   that this be carried out under the control of a dynamic control plane
   based on Generalized MPLS (GMPLS) [RFC3945].  Implementations for SMP
   with GMPLS exist, and the general principles of its operation are
   well known, if not fully documented.

   However, there are operators, in particular in the transport sector,
   that do not operate their MPLS-TP networks under the control of a
   control plane or for other reasons have delegated executive action
   for resilience to the data plane, and require the ability to utilize





Weingarten, et al.            Informational                     [Page 8]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


   SMP protection.  For such networks, it is imperative that it be
   possible to perform all required coordination of selectors and
   endpoints for SMP via data-plane operations.

5.  SMP Network Objectives

5.1.  Resource Reservation and Coordination

   SMP is based on pre-configuration of the working paths and the
   corresponding protection paths.  This configuration may be based on
   either a control protocol or static configuration by the management
   system.  However, even when the configuration is performed by a
   control protocol, e.g., GMPLS, the control protocol SHALL NOT be used
   as the primary mechanism for detecting or reporting network failures,
   or for initiating or coordinating protection switchover.  That is, it
   SHALL NOT be used as the primary resilience mechanism.

   The protection relationship between the working and protection paths
   SHOULD be configured, and the shared segments of the protection path
   MUST be identified prior to use of the protection paths.  Relative
   priority for working paths to be used to resolve contention for
   protection path usage by multiple working paths MAY also be specified
   ahead of time.

   When a protection switch is triggered by any fault condition or
   operator command, the SMP network MUST perform two operations --
   switch data traffic over to a protection path, and coordinate the
   utilization of the associated shared resources.  To provide fast
   protection, both operations MUST occur at the same time or as close
   to the same time as possible.

   In the case of multiple working paths failing, the shared resource
   utilization coordination SHALL be between the different working paths
   in the SMP network.

5.1.1.  Checking Resource Availability for Multiple Protection Paths

   In a hard-preemption scenario, when an endpoint identifies a
   protection switching trigger and has more than one potential action
   (e.g., m:1 protection), it MUST verify that the necessary protection
   resources are available on the selected protection path.  The
   resources may not be available because they have already been
   utilized for the protection of, for example, one or more higher-
   priority working paths.







Weingarten, et al.            Informational                     [Page 9]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


5.2.  Multiple Triggers

   If more than one working path is triggering a protection switch such
   that a protection segment is oversubscribed, there are two different
   actions that the SMP network can choose -- soft preemption and hard
   preemption [RFC6372].

5.2.1.  Soft Preemption

   For networks that support multiplexing packets over the shared
   segments, the requirement is as follows:

   o  All of the protection paths MAY be allowed to share the resources
      of the shared segments.

5.2.2.  Hard Preemption

   There are networks that require the exclusive use of the protection
   resources when a protection segment is oversubscribed.  Traffic of
   lower-priority paths is completely blocked.  These include networks
   that support the requirements in [RFC5654], and in particular support
   Requirement 58.  For such networks, the following requirements apply:

   1. Relative priority MAY be assigned to each of the working paths of
      an SMP domain.  If the priority is not assigned, the working paths
      are assumed to have equal priority.

   2. Resources of the shared segments SHALL be utilized by the
      protection path according to the highest priority amongst those
      requesting use of the resources.

   3. If multiple protection paths of equal priority are requesting the
      shared resources, the resources SHALL be utilized on a first come
      first served basis.  Traffic of the protection paths that request
      the shared resources late SHALL be preempted.  In order to cover
      the situation where the first come first served principle cannot
      resolve the contention among multiple equal-priority requests,
      i.e., when the requests occur simultaneously, tie-breaking rules
      SHALL be defined in the scope of an SMP domain.

   4. If a higher-priority path requires the protection resources that
      are being utilized by a lower-priority path, the resources SHALL
      be utilized by the higher-priority path.  Traffic with the lower
      priority SHALL be preempted.







Weingarten, et al.            Informational                    [Page 10]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


   5. Once resources of shared segments have been successfully utilized
      by a protection path, the traffic on that protection path SHALL
      NOT be interrupted by any protection traffic whose priority is
      equal to or lower than the protecting path currently in use.

   6. During preemption, shared segment resources MAY be used by both
      existing traffic (that is being preempted) and higher-priority
      traffic.

5.3.  Notification

   When a working path endpoint has a protection switch triggered, it
   SHOULD attempt to switch the traffic to the protection path and
   request the coordination of the shared resource utilization.  If the
   necessary shared resources are unavailable, the endpoints of the
   requesting working path SHALL be notified of protection switchover
   failure, and switchover will not be completed.

   Similarly, if preemption is supported and the resources currently
   utilized by a particular working path are being preempted, then the
   endpoints of the affected working path whose traffic is being
   preempted SHALL be notified that the resources are being preempted.
   As described in [RFC6372], the event of preemption may be detected by
   Operations, Administration, and Maintenance (OAM) and reported as a
   fault or a degradation of traffic delivery.

5.4.  Reversion

   When the condition that triggered the protection switch is cleared,
   it is possible to either revert to using the working path resources
   or continue to utilize the protection resources.  Continuing the use
   of protection resources allows the operator to delay the disruption
   of service caused by the switchover until periods of lighter traffic.
   The switchover would need to be performed via an explicit operator
   command, unless the protection resources are preempted by a higher-
   priority fault.  Hence, both automatic and manual revertive behaviors
   MUST be supported for hard preemption in an SMP domain.  Normally,
   the network should revert to use of the working path resources in
   order to clear the protection resources for protection of other path
   triggers.  However, the protocol MUST support non-revertive
   configurations.

5.5.  Protection Switching Time

   Protection switching time refers to the transfer time (Tt) defined in
   [G.808.1] and recovery switching time defined in [RFC4427], and is
   defined as the interval after a switching trigger is identified until
   the traffic begins to be transmitted on the protection path.  This



Weingarten, et al.            Informational                    [Page 11]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


   time does not include the time needed to initiate the protection
   switching process after a failure occurred, and the time needed to
   complete preemption of existing traffic on the shared segments as
   described in Section 4.2.  The time needed to initiate the protection
   switching process, which is known as detection time or correlation
   time in [RFC4427], is related to the OAM or management process, but
   the time needed to complete preemption is related to the actions
   within an SMP domain.  Support for a protection switching time of
   50 ms is dependent upon the initial switchover to the protection
   path, but the preemption time SHOULD also be taken into account to
   minimize total service interruption time.

   When triggered, protection switching action SHOULD be initiated
   immediately to minimize service interruption time.

5.6.  Timers

   In order to prevent multiple switching actions for a single switching
   trigger, when there are multiple layers of networks, SMP SHOULD be
   controlled by a hold-off timer that would allow lower-layer
   mechanisms to complete their switching actions before invoking SMP
   protection actions as described in [RFC6372].

   In order to prevent an unstable recovering working path from invoking
   intermittent switching operations, SMP SHOULD employ a
   Wait-To-Restore timer during any reversion switching, as described in
   [RFC6372].

5.7.  Communication Channel and Fate-Sharing

   SMP SHOULD provide a communication channel, along the protection
   path, between the endpoints of the protection path, to support fast
   protection switching.

   SMP in hard-preemption mode SHOULD include support for communicating
   information to coordinate the use of the shared protection resources
   among multiple working paths.  The message encoding and communication
   channel between the nodes of the shared protection resource and the
   endpoints of the protection path are out of the scope of this
   document.

   Bidirectional protection switching SHOULD be supported in SMP.









Weingarten, et al.            Informational                    [Page 12]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


6.  Manageability Considerations

   The network management architecture and requirements for MPLS-TP are
   specified in [RFC5951].  They derive from the generic specifications
   described in ITU-T G.7710/Y.1701 [G.7710] for transport technologies.
   This document does not introduce any new manageability requirements
   beyond those covered in those documents.

7.  Security Considerations

   General security considerations for MPLS-TP are covered in [RFC5921].
   The security considerations for the generic associated control
   channel are described in [RFC5586].

   Security considerations for any proposed solution should consider
   exhaustion of resources related to preemption, especially by a
   malicious actor as a threat vector against which the resources should
   be protected.  Protections should also be considered to prevent a
   malicious actor from attempting to create an alternate path on which
   to force traffic from a sensor/device, thereby enabling pervasive
   monitoring [RFC7258].

8.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.

   [RFC3945]  Mannie, E., Ed., "Generalized Multi-Protocol Label
              Switching (GMPLS) Architecture", RFC 3945, October 2004,
              <http://www.rfc-editor.org/info/rfc3945>.

   [RFC4426]  Lang, J., Ed., Rajagopalan, B., Ed., and D. Papadimitriou,
              Ed., "Generalized Multi-Protocol Label Switching (GMPLS)
              Recovery Functional Specification", RFC 4426, March 2006,
              <http://www.rfc-editor.org/info/rfc4426>.

   [RFC4427]  Mannie, E., Ed., and D. Papadimitriou, Ed., "Recovery
              (Protection and Restoration) Terminology for Generalized
              Multi-Protocol Label Switching (GMPLS)", RFC 4427,
              March 2006, <http://www.rfc-editor.org/info/rfc4427>.

   [RFC4428]  Papadimitriou, D., Ed., and E. Mannie, Ed., "Analysis of
              Generalized Multi-Protocol Label Switching (GMPLS)-based
              Recovery Mechanisms (including Protection and
              Restoration)", RFC 4428, March 2006,
              <http://www.rfc-editor.org/info/rfc4428>.




Weingarten, et al.            Informational                    [Page 13]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


   [RFC5586]  Bocci, M., Ed., Vigoureux, M., Ed., and S. Bryant, Ed.,
              "MPLS Generic Associated Channel", RFC 5586, June 2009,
              <http://www.rfc-editor.org/info/rfc5586>.

   [RFC5654]  Niven-Jenkins, B., Ed., Brungard, D., Ed., Betts, M., Ed.,
              Sprecher, N., and S. Ueno, "Requirements of an MPLS
              Transport Profile", RFC 5654, September 2009,
              <http://www.rfc-editor.org/info/rfc5654>.

   [RFC5921]  Bocci, M., Ed., Bryant, S., Ed., Frost, D., Ed., Levrau,
              L., and L. Berger, "A Framework for MPLS in Transport
              Networks", RFC 5921, July 2010,
              <http://www.rfc-editor.org/info/rfc5921>.

   [RFC5951]  Lam, K., Mansfield, S., and E. Gray, "Network Management
              Requirements for MPLS-based Transport Networks", RFC 5951,
              September 2010, <http://www.rfc-editor.org/info/rfc5951>.

   [RFC6372]  Sprecher, N., Ed., and A. Farrel, Ed., "MPLS Transport
              Profile (MPLS-TP) Survivability Framework", RFC 6372,
              September 2011, <http://www.rfc-editor.org/info/rfc6372>.

   [RFC6378]  Weingarten, Y., Ed., Bryant, S., Osborne, E., Sprecher,
              N., and A. Fulignoli, Ed., "MPLS Transport Profile
              (MPLS-TP) Linear Protection", RFC 6378, October 2011,
              <http://www.rfc-editor.org/info/rfc6378>.

   [RFC7258]  Farrell, S. and H. Tschofenig, "Pervasive Monitoring Is an
              Attack", BCP 188, RFC 7258, May 2014,
              <http://www.rfc-editor.org/info/rfc7258>.

   [RFC7271]  Ryoo, J., Ed., Gray, E., Ed., van Helvoort, H.,
              D'Alessandro, A., Cheung, T., and E. Osborne, "MPLS
              Transport Profile (MPLS-TP) Linear Protection to Match the
              Operational Expectations of Synchronous Digital Hierarchy,
              Optical Transport Network, and Ethernet Transport Network
              Operators", RFC 7271, June 2014,
              <http://www.rfc-editor.org/info/rfc7271>.

   [G.7710]   International Telecommunication Union, "Common equipment
              management function requirements", ITU-T Recommendation
              G.7710/Y.1701, February 2012.

   [G.808.1]  International Telecommunication Union, "Generic Protection
              Switching - Linear trail and subnetwork protection", ITU-T
              Recommendation G.808.1, May 2014.





Weingarten, et al.            Informational                    [Page 14]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


Acknowledgements

   This document is the outcome of discussions on Shared Mesh Protection
   for MPLS-TP.  The authors would like to thank all contributors to
   these discussions, and especially Eric Osborne for facilitating them.

   We would also like to thank Matt Hartley for working on the English
   review and Lou Berger for his valuable comments and suggestions on
   this document.

Contributors

   David Allan
   Ericsson
   EMail: david.i.allan@ericsson.com

   Daniel King
   Old Dog Consulting
   EMail: daniel@olddog.co.uk

   Taesik Cheung
   ETRI
   EMail: cts@etri.re.kr




























Weingarten, et al.            Informational                    [Page 15]
^L
RFC 7412                  MPLS SMP Requirements            December 2014


Authors' Addresses

   Yaacov Weingarten
   34 Hagefen St.
   Karnei Shomron,  4485500
   Israel

   EMail: wyaacov@gmail.com


   Sam Aldrin
   Huawei Technologies
   2330 Central Expressway
   Santa Clara, CA  95050
   United States

   EMail: aldrin.ietf@gmail.com


   Ping Pan
   Infinera

   EMail: ppan@infinera.com


   Jeong-dong Ryoo
   ETRI
   218 Gajeongno
   Yuseong, Daejeon  305-700
   South Korea

   EMail: ryoo@etri.re.kr


   Greg Mirsky
   Ericsson

   EMail: gregory.mirsky@ericsson.com













Weingarten, et al.            Informational                    [Page 16]
^L